#define RS422_MODE 2
#define RS485_4WIRE_MODE 3
#define OP_MODE_MASK 3
-// above add by Victor Yu. 01-05-2004
-
-#define TTY_THRESHOLD_THROTTLE 128
-
-#define LO_WATER (TTY_FLIPBUF_SIZE)
-#define HI_WATER (TTY_FLIPBUF_SIZE*2*3/4)
-
-// added by James. 03-11-2004.
-#define MOXA_SDS_GETICOUNTER (MOXA + 68)
-#define MOXA_SDS_RSTICOUNTER (MOXA + 69)
-// (above) added by James.
+#define MOXA_SDS_RSTICOUNTER (MOXA + 69)
#define MOXA_ASPP_OQUEUE (MOXA + 70)
#define MOXA_ASPP_SETBAUD (MOXA + 71)
#define MOXA_ASPP_GETBAUD (MOXA + 72)
#define MOXA_ASPP_MON_EXT (MOXA + 75)
#define MOXA_SET_BAUD_METHOD (MOXA + 76)
-
/* --------------------------------------------------- */
#define NPPI_NOTIFY_PARITY 0x01
#define NPPI_NOTIFY_SW_OVERRUN 0x08
#define NPPI_NOTIFY_BREAK 0x10
-#define NPPI_NOTIFY_CTSHOLD 0x01 // Tx hold by CTS low
-#define NPPI_NOTIFY_DSRHOLD 0x02 // Tx hold by DSR low
-#define NPPI_NOTIFY_XOFFHOLD 0x08 // Tx hold by Xoff received
-#define NPPI_NOTIFY_XOFFXENT 0x10 // Xoff Sent
-
-//CheckIsMoxaMust return value
-#define MOXA_OTHER_UART 0x00
-#define MOXA_MUST_MU150_HWID 0x01
-#define MOXA_MUST_MU860_HWID 0x02
-
-// follow just for Moxa Must chip define.
-//
-// when LCR register (offset 0x03) write following value,
-// the Must chip will enter enchance mode. And write value
-// on EFR (offset 0x02) bit 6,7 to change bank.
+#define NPPI_NOTIFY_CTSHOLD 0x01 /* Tx hold by CTS low */
+#define NPPI_NOTIFY_DSRHOLD 0x02 /* Tx hold by DSR low */
+#define NPPI_NOTIFY_XOFFHOLD 0x08 /* Tx hold by Xoff received */
+#define NPPI_NOTIFY_XOFFXENT 0x10 /* Xoff Sent */
+
+/* follow just for Moxa Must chip define. */
+/* */
+/* when LCR register (offset 0x03) write following value, */
+/* the Must chip will enter enchance mode. And write value */
+/* on EFR (offset 0x02) bit 6,7 to change bank. */
#define MOXA_MUST_ENTER_ENCHANCE 0xBF
-// when enhance mode enable, access on general bank register
+/* when enhance mode enable, access on general bank register */
#define MOXA_MUST_GDL_REGISTER 0x07
#define MOXA_MUST_GDL_MASK 0x7F
#define MOXA_MUST_GDL_HAS_BAD_DATA 0x80
-#define MOXA_MUST_LSR_RERR 0x80 // error in receive FIFO
-// enchance register bank select and enchance mode setting register
-// when LCR register equal to 0xBF
+#define MOXA_MUST_LSR_RERR 0x80 /* error in receive FIFO */
+/* enchance register bank select and enchance mode setting register */
+/* when LCR register equal to 0xBF */
#define MOXA_MUST_EFR_REGISTER 0x02
-// enchance mode enable
+/* enchance mode enable */
#define MOXA_MUST_EFR_EFRB_ENABLE 0x10
-// enchance reister bank set 0, 1, 2
+/* enchance reister bank set 0, 1, 2 */
#define MOXA_MUST_EFR_BANK0 0x00
#define MOXA_MUST_EFR_BANK1 0x40
#define MOXA_MUST_EFR_BANK2 0x80
#define MOXA_MUST_EFR_BANK3 0xC0
#define MOXA_MUST_EFR_BANK_MASK 0xC0
-// set XON1 value register, when LCR=0xBF and change to bank0
+/* set XON1 value register, when LCR=0xBF and change to bank0 */
#define MOXA_MUST_XON1_REGISTER 0x04
-// set XON2 value register, when LCR=0xBF and change to bank0
+/* set XON2 value register, when LCR=0xBF and change to bank0 */
#define MOXA_MUST_XON2_REGISTER 0x05
-// set XOFF1 value register, when LCR=0xBF and change to bank0
+/* set XOFF1 value register, when LCR=0xBF and change to bank0 */
#define MOXA_MUST_XOFF1_REGISTER 0x06
-// set XOFF2 value register, when LCR=0xBF and change to bank0
+/* set XOFF2 value register, when LCR=0xBF and change to bank0 */
#define MOXA_MUST_XOFF2_REGISTER 0x07
#define MOXA_MUST_RBRTL_REGISTER 0x04
#define MOXA_MUST_ECR_REGISTER 0x06
#define MOXA_MUST_CSR_REGISTER 0x07
-// good data mode enable
+/* good data mode enable */
#define MOXA_MUST_FCR_GDA_MODE_ENABLE 0x20
-// only good data put into RxFIFO
+/* only good data put into RxFIFO */
#define MOXA_MUST_FCR_GDA_ONLY_ENABLE 0x10
-// enable CTS interrupt
+/* enable CTS interrupt */
#define MOXA_MUST_IER_ECTSI 0x80
-// enable RTS interrupt
+/* enable RTS interrupt */
#define MOXA_MUST_IER_ERTSI 0x40
-// enable Xon/Xoff interrupt
+/* enable Xon/Xoff interrupt */
#define MOXA_MUST_IER_XINT 0x20
-// enable GDA interrupt
+/* enable GDA interrupt */
#define MOXA_MUST_IER_EGDAI 0x10
#define MOXA_MUST_RECV_ISR (UART_IER_RDI | MOXA_MUST_IER_EGDAI)
-// GDA interrupt pending
+/* GDA interrupt pending */
#define MOXA_MUST_IIR_GDA 0x1C
#define MOXA_MUST_IIR_RDA 0x04
#define MOXA_MUST_IIR_RTO 0x0C
#define MOXA_MUST_IIR_LSR 0x06
-// recieved Xon/Xoff or specical interrupt pending
+/* recieved Xon/Xoff or specical interrupt pending */
#define MOXA_MUST_IIR_XSC 0x10
-// RTS/CTS change state interrupt pending
+/* RTS/CTS change state interrupt pending */
#define MOXA_MUST_IIR_RTSCTS 0x20
#define MOXA_MUST_IIR_MASK 0x3E
#define MOXA_MUST_MCR_XON_ANY 0x80
#define MOXA_MUST_MCR_TX_XON 0x08
-
-// software flow control on chip mask value
+/* software flow control on chip mask value */
#define MOXA_MUST_EFR_SF_MASK 0x0F
-// send Xon1/Xoff1
+/* send Xon1/Xoff1 */
#define MOXA_MUST_EFR_SF_TX1 0x08
-// send Xon2/Xoff2
+/* send Xon2/Xoff2 */
#define MOXA_MUST_EFR_SF_TX2 0x04
-// send Xon1,Xon2/Xoff1,Xoff2
+/* send Xon1,Xon2/Xoff1,Xoff2 */
#define MOXA_MUST_EFR_SF_TX12 0x0C
-// don't send Xon/Xoff
+/* don't send Xon/Xoff */
#define MOXA_MUST_EFR_SF_TX_NO 0x00
-// Tx software flow control mask
+/* Tx software flow control mask */
#define MOXA_MUST_EFR_SF_TX_MASK 0x0C
-// don't receive Xon/Xoff
+/* don't receive Xon/Xoff */
#define MOXA_MUST_EFR_SF_RX_NO 0x00
-// receive Xon1/Xoff1
+/* receive Xon1/Xoff1 */
#define MOXA_MUST_EFR_SF_RX1 0x02
-// receive Xon2/Xoff2
+/* receive Xon2/Xoff2 */
#define MOXA_MUST_EFR_SF_RX2 0x01
-// receive Xon1,Xon2/Xoff1,Xoff2
+/* receive Xon1,Xon2/Xoff1,Xoff2 */
#define MOXA_MUST_EFR_SF_RX12 0x03
-// Rx software flow control mask
+/* Rx software flow control mask */
#define MOXA_MUST_EFR_SF_RX_MASK 0x03
-//#define MOXA_MUST_MIN_XOFFLIMIT 66
-//#define MOXA_MUST_MIN_XONLIMIT 20
-//#define ID1_RX_TRIG 120
-
-
-#define CHECK_MOXA_MUST_XOFFLIMIT(info) { \
- if ( (info)->IsMoxaMustChipFlag && \
- (info)->HandFlow.XoffLimit < MOXA_MUST_MIN_XOFFLIMIT ) { \
- (info)->HandFlow.XoffLimit = MOXA_MUST_MIN_XOFFLIMIT; \
- (info)->HandFlow.XonLimit = MOXA_MUST_MIN_XONLIMIT; \
- } \
-}
-
-#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+#define ENABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr |= MOXA_MUST_EFR_EFRB_ENABLE; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define DISABLE_MOXA_MUST_ENCHANCE_MODE(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define SET_MOXA_MUST_XON1_VALUE(baseio, Value) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK0; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK0; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
outb((u8)(Value), (baseio)+MOXA_MUST_XON1_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
-#define SET_MOXA_MUST_XON2_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK0; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_XON2_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_XOFF1_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK0; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK0; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
outb((u8)(Value), (baseio)+MOXA_MUST_XOFF1_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
-#define SET_MOXA_MUST_XOFF2_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK0; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_XOFF2_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_RBRTL_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_RBRTL_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_RBRTH_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_RBRTH_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_RBRTI_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_RBRTI_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_THRTL_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_THRTL_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-//#define MOXA_MUST_RBRL_VALUE 4
-#define SET_MOXA_MUST_FIFO_VALUE(info) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((info)->ioaddr+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR); \
+#define SET_MOXA_MUST_FIFO_VALUE(info) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((info)->ioaddr+UART_LCR); \
+ outb(MOXA_MUST_ENTER_ENCHANCE, (info)->ioaddr+UART_LCR);\
__efr = inb((info)->ioaddr+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK1; \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK1; \
outb(__efr, (info)->ioaddr+MOXA_MUST_EFR_REGISTER); \
- outb((u8)((info)->rx_high_water), (info)->ioaddr+MOXA_MUST_RBRTH_REGISTER); \
- outb((u8)((info)->rx_trigger), (info)->ioaddr+MOXA_MUST_RBRTI_REGISTER); \
- outb((u8)((info)->rx_low_water), (info)->ioaddr+MOXA_MUST_RBRTL_REGISTER); \
- outb(__oldlcr, (info)->ioaddr+UART_LCR); \
-}
-
-
-
-#define SET_MOXA_MUST_ENUM_VALUE(baseio, Value) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK2; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb((u8)(Value), (baseio)+MOXA_MUST_ENUM_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
- __efr |= MOXA_MUST_EFR_BANK2; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_MASK; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_JUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
- outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_MASK; \
- __efr |= MOXA_MUST_EFR_SF_TX1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ outb((u8)((info)->rx_high_water), (info)->ioaddr+ \
+ MOXA_MUST_RBRTH_REGISTER); \
+ outb((u8)((info)->rx_trigger), (info)->ioaddr+ \
+ MOXA_MUST_RBRTI_REGISTER); \
+ outb((u8)((info)->rx_low_water), (info)->ioaddr+ \
+ MOXA_MUST_RBRTL_REGISTER); \
+ outb(__oldlcr, (info)->ioaddr+UART_LCR); \
+} while (0)
+
+#define GET_MOXA_MUST_HARDWARE_ID(baseio, pId) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \
- __efr |= MOXA_MUST_EFR_SF_TX1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_BANK_MASK; \
+ __efr |= MOXA_MUST_EFR_BANK2; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ *pId = inb((baseio)+MOXA_MUST_HWID_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define SET_MOXA_MUST_JUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_MASK; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_MASK; \
- __efr |= MOXA_MUST_EFR_SF_RX1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \
+ __efr |= MOXA_MUST_EFR_SF_TX1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \
- __efr |= MOXA_MUST_EFR_SF_RX1; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_TX_MASK; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define ENABLE_MOXA_MUST_TX_RX_SOFTWARE_FLOW_CONTROL(baseio) { \
- u8 __oldlcr, __efr; \
- __oldlcr = inb((baseio)+UART_LCR); \
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \
+ __efr |= MOXA_MUST_EFR_SF_RX1; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
+
+#define DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(baseio) do { \
+ u8 __oldlcr, __efr; \
+ __oldlcr = inb((baseio)+UART_LCR); \
outb(MOXA_MUST_ENTER_ENCHANCE, (baseio)+UART_LCR); \
- __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
- __efr &= ~MOXA_MUST_EFR_SF_MASK; \
- __efr |= (MOXA_MUST_EFR_SF_RX1|MOXA_MUST_EFR_SF_TX1); \
- outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
- outb(__oldlcr, (baseio)+UART_LCR); \
-}
-
-#define ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \
- u8 __oldmcr; \
- __oldmcr = inb((baseio)+UART_MCR); \
- __oldmcr |= MOXA_MUST_MCR_XON_ANY; \
- outb(__oldmcr, (baseio)+UART_MCR); \
-}
-
-#define DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(baseio) { \
- u8 __oldmcr; \
- __oldmcr = inb((baseio)+UART_MCR); \
- __oldmcr &= ~MOXA_MUST_MCR_XON_ANY; \
- outb(__oldmcr, (baseio)+UART_MCR); \
-}
-
-#define READ_MOXA_MUST_GDL(baseio) inb((baseio)+MOXA_MUST_GDL_REGISTER)
+ __efr = inb((baseio)+MOXA_MUST_EFR_REGISTER); \
+ __efr &= ~MOXA_MUST_EFR_SF_RX_MASK; \
+ outb(__efr, (baseio)+MOXA_MUST_EFR_REGISTER); \
+ outb(__oldlcr, (baseio)+UART_LCR); \
+} while (0)
#endif
projects / linux-drm-fsl-dcu.git / commitdiff