Required subnode-properties:
- label: Descriptive name of the key.
- linux,code: Keycode to emit.
- - channel: Channel this key is attached to, mut be 0 or 1.
+ - channel: Channel this key is attached to, must be 0 or 1.
- voltage: Voltage in µV at lradc input when this key is pressed.
Example:
as RedBoot.
The partition table should be a subnode of the mtd node and should be named
-'partitions'. Partitions are defined in subnodes of the partitions node.
+'partitions'. This node should have the following property:
+- compatible : (required) must be "fixed-partitions"
+Partitions are then defined in subnodes of the partitions node.
For backwards compatibility partitions as direct subnodes of the mtd device are
supported. This use is discouraged.
flash@0 {
partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
flash@1 {
partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <2>;
flash@2 {
partitions {
+ compatible = "fixed-partitions";
#address-cells = <2>;
#size-cells = <2>;
S: Maintained
F: drivers/pinctrl/samsung/
+PIN CONTROLLER - SINGLE
+M: Tony Lindgren <tony@atomide.com>
+M: Haojian Zhuang <haojian.zhuang@linaro.org>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L: linux-omap@vger.kernel.org
+S: Maintained
+F: drivers/pinctrl/pinctrl-single.c
+
PIN CONTROLLER - ST SPEAR
M: Viresh Kumar <vireshk@kernel.org>
L: spear-devel@list.st.com
VERSION = 4
PATCHLEVEL = 4
SUBLEVEL = 0
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc7
NAME = Blurry Fish Butt
# *DOCUMENTATION*
However some customers have peripherals mapped at this addr, so
Linux needs to be scooted a bit.
If you don't know what the above means, leave this setting alone.
+ This needs to match memory start address specified in Device Tree
config HIGHMEM
bool "High Memory Support"
LIBGCC := $(shell $(CC) $(cflags-y) --print-libgcc-file-name)
# Modules with short calls might break for calls into builtin-kernel
-KBUILD_CFLAGS_MODULE += -mlong-calls
+KBUILD_CFLAGS_MODULE += -mlong-calls -mno-millicode
# Finally dump eveything into kernel build system
KBUILD_CFLAGS += $(cflags-y)
snps,pbl = < 32 >;
clocks = <&apbclk>;
clock-names = "stmmaceth";
+ max-speed = <100>;
};
ehci@0x40000 {
memory {
device_type = "memory";
- reg = <0x0 0x80000000 0x0 0x40000000 /* 1 GB low mem */
+ /* CONFIG_LINUX_LINK_BASE needs to match low mem start */
+ reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MB low mem */
0x1 0x00000000 0x0 0x40000000>; /* 1 GB highmem */
};
#define ARC_REG_IC_IVIC 0x10
#define ARC_REG_IC_CTRL 0x11
#define ARC_REG_IC_IVIL 0x19
-#if defined(CONFIG_ARC_MMU_V3) || defined(CONFIG_ARC_MMU_V4)
#define ARC_REG_IC_PTAG 0x1E
-#endif
#define ARC_REG_IC_PTAG_HI 0x1F
/* Bit val in IC_CTRL */
* @dt_compat: Array of device tree 'compatible' strings
* (XXX: although only 1st entry is looked at)
* @init_early: Very early callback [called from setup_arch()]
- * @init_cpu_smp: for each CPU as it is coming up (SMP as well as UP)
+ * @init_per_cpu: for each CPU as it is coming up (SMP as well as UP)
* [(M):init_IRQ(), (o):start_kernel_secondary()]
* @init_machine: arch initcall level callback (e.g. populate static
* platform devices or parse Devicetree)
const char **dt_compat;
void (*init_early)(void);
#ifdef CONFIG_SMP
- void (*init_cpu_smp)(unsigned int);
+ void (*init_per_cpu)(unsigned int);
#endif
void (*init_machine)(void);
void (*init_late)(void);
* @init_early_smp: A SMP specific h/w block can init itself
* Could be common across platforms so not covered by
* mach_desc->init_early()
- * @init_irq_cpu: Called for each core so SMP h/w block driver can do
+ * @init_per_cpu: Called for each core so SMP h/w block driver can do
* any needed setup per cpu (e.g. IPI request)
* @cpu_kick: For Master to kickstart a cpu (optionally at a PC)
* @ipi_send: To send IPI to a @cpu
struct plat_smp_ops {
const char *info;
void (*init_early_smp)(void);
- void (*init_irq_cpu)(int cpu);
+ void (*init_per_cpu)(int cpu);
void (*cpu_kick)(int cpu, unsigned long pc);
void (*ipi_send)(int cpu);
void (*ipi_clear)(int irq);
extern int arc_unwind(struct unwind_frame_info *frame);
extern void arc_unwind_init(void);
-extern void arc_unwind_setup(void);
extern void *unwind_add_table(struct module *module, const void *table_start,
unsigned long table_size);
extern void unwind_remove_table(void *handle, int init_only);
{
}
-static inline void arc_unwind_setup(void)
-{
-}
#define unwind_add_table(a, b, c)
#define unwind_remove_table(a, b)
static int arcv2_irq_map(struct irq_domain *d, unsigned int irq,
irq_hw_number_t hw)
{
- if (irq == TIMER0_IRQ || irq == IPI_IRQ)
+ /*
+ * core intc IRQs [16, 23]:
+ * Statically assigned always private-per-core (Timers, WDT, IPI, PCT)
+ */
+ if (hw < 24) {
+ /*
+ * A subsequent request_percpu_irq() fails if percpu_devid is
+ * not set. That in turns sets NOAUTOEN, meaning each core needs
+ * to call enable_percpu_irq()
+ */
+ irq_set_percpu_devid(irq);
irq_set_chip_and_handler(irq, &arcv2_irq_chip, handle_percpu_irq);
- else
+ } else {
irq_set_chip_and_handler(irq, &arcv2_irq_chip, handle_level_irq);
+ }
return 0;
}
#ifdef CONFIG_SMP
/* a SMP H/w block could do IPI IRQ request here */
- if (plat_smp_ops.init_irq_cpu)
- plat_smp_ops.init_irq_cpu(smp_processor_id());
+ if (plat_smp_ops.init_per_cpu)
+ plat_smp_ops.init_per_cpu(smp_processor_id());
- if (machine_desc->init_cpu_smp)
- machine_desc->init_cpu_smp(smp_processor_id());
+ if (machine_desc->init_per_cpu)
+ machine_desc->init_per_cpu(smp_processor_id());
#endif
}
set_irq_regs(old_regs);
}
+/*
+ * API called for requesting percpu interrupts - called by each CPU
+ * - For boot CPU, actually request the IRQ with genirq core + enables
+ * - For subsequent callers only enable called locally
+ *
+ * Relies on being called by boot cpu first (i.e. request called ahead) of
+ * any enable as expected by genirq. Hence Suitable only for TIMER, IPI
+ * which are guaranteed to be setup on boot core first.
+ * Late probed peripherals such as perf can't use this as there no guarantee
+ * of being called on boot CPU first.
+ */
+
void arc_request_percpu_irq(int irq, int cpu,
irqreturn_t (*isr)(int irq, void *dev),
const char *irq_nm,
if (!cpu) {
int rc;
+#ifdef CONFIG_ISA_ARCOMPACT
/*
- * These 2 calls are essential to making percpu IRQ APIs work
- * Ideally these details could be hidden in irq chip map function
- * but the issue is IPIs IRQs being static (non-DT) and platform
- * specific, so we can't identify them there.
+ * A subsequent request_percpu_irq() fails if percpu_devid is
+ * not set. That in turns sets NOAUTOEN, meaning each core needs
+ * to call enable_percpu_irq()
+ *
+ * For ARCv2, this is done in irq map function since we know
+ * which irqs are strictly per cpu
*/
irq_set_percpu_devid(irq);
- irq_modify_status(irq, IRQ_NOAUTOEN, 0); /* @irq, @clr, @set */
+#endif
rc = request_percpu_irq(irq, isr, irq_nm, percpu_dev);
if (rc)
struct plat_smp_ops plat_smp_ops = {
.info = smp_cpuinfo_buf,
.init_early_smp = mcip_probe_n_setup,
- .init_irq_cpu = mcip_setup_per_cpu,
+ .init_per_cpu = mcip_setup_per_cpu,
.ipi_send = mcip_ipi_send,
.ipi_clear = mcip_ipi_clear,
};
#endif /* CONFIG_ISA_ARCV2 */
-void arc_cpu_pmu_irq_init(void)
+static void arc_cpu_pmu_irq_init(void *data)
{
- struct arc_pmu_cpu *pmu_cpu = this_cpu_ptr(&arc_pmu_cpu);
+ int irq = *(int *)data;
- arc_request_percpu_irq(arc_pmu->irq, smp_processor_id(), arc_pmu_intr,
- "ARC perf counters", pmu_cpu);
+ enable_percpu_irq(irq, IRQ_TYPE_NONE);
/* Clear all pending interrupt flags */
write_aux_reg(ARC_REG_PCT_INT_ACT, 0xffffffff);
if (has_interrupts) {
int irq = platform_get_irq(pdev, 0);
- unsigned long flags;
if (irq < 0) {
pr_err("Cannot get IRQ number for the platform\n");
arc_pmu->irq = irq;
- /*
- * arc_cpu_pmu_irq_init() needs to be called on all cores for
- * their respective local PMU.
- * However we use opencoded on_each_cpu() to ensure it is called
- * on core0 first, so that arc_request_percpu_irq() sets up
- * AUTOEN etc. Otherwise enable_percpu_irq() fails to enable
- * perf IRQ on non master cores.
- * see arc_request_percpu_irq()
- */
- preempt_disable();
- local_irq_save(flags);
- arc_cpu_pmu_irq_init();
- local_irq_restore(flags);
- smp_call_function((smp_call_func_t)arc_cpu_pmu_irq_init, 0, 1);
- preempt_enable();
-
- /* Clean all pending interrupt flags */
- write_aux_reg(ARC_REG_PCT_INT_ACT, 0xffffffff);
+ /* intc map function ensures irq_set_percpu_devid() called */
+ request_percpu_irq(irq, arc_pmu_intr, "ARC perf counters",
+ this_cpu_ptr(&arc_pmu_cpu));
+
+ on_each_cpu(arc_cpu_pmu_irq_init, &irq, 1);
+
} else
arc_pmu->pmu.capabilities |= PERF_PMU_CAP_NO_INTERRUPT;
#endif
arc_unwind_init();
- arc_unwind_setup();
}
static int __init customize_machine(void)
pr_info("## CPU%u LIVE ##: Executing Code...\n", cpu);
/* Some SMP H/w setup - for each cpu */
- if (plat_smp_ops.init_irq_cpu)
- plat_smp_ops.init_irq_cpu(cpu);
+ if (plat_smp_ops.init_per_cpu)
+ plat_smp_ops.init_per_cpu(cpu);
- if (machine_desc->init_cpu_smp)
- machine_desc->init_cpu_smp(cpu);
+ if (machine_desc->init_per_cpu)
+ machine_desc->init_per_cpu(cpu);
arc_local_timer_setup();
static unsigned long read_pointer(const u8 **pLoc,
const void *end, signed ptrType);
+static void init_unwind_hdr(struct unwind_table *table,
+ void *(*alloc) (unsigned long));
+
+/*
+ * wrappers for header alloc (vs. calling one vs. other at call site)
+ * to elide section mismatches warnings
+ */
+static void *__init unw_hdr_alloc_early(unsigned long sz)
+{
+ return __alloc_bootmem_nopanic(sz, sizeof(unsigned int),
+ MAX_DMA_ADDRESS);
+}
+
+static void *unw_hdr_alloc(unsigned long sz)
+{
+ return kmalloc(sz, GFP_KERNEL);
+}
static void init_unwind_table(struct unwind_table *table, const char *name,
const void *core_start, unsigned long core_size,
__start_unwind, __end_unwind - __start_unwind,
NULL, 0);
/*__start_unwind_hdr, __end_unwind_hdr - __start_unwind_hdr);*/
+
+ init_unwind_hdr(&root_table, unw_hdr_alloc_early);
}
static const u32 bad_cie, not_fde;
e2->fde = v;
}
-static void __init setup_unwind_table(struct unwind_table *table,
- void *(*alloc) (unsigned long))
+static void init_unwind_hdr(struct unwind_table *table,
+ void *(*alloc) (unsigned long))
{
const u8 *ptr;
unsigned long tableSize = table->size, hdrSize;
if (cie == ¬_fde)
continue;
if (cie == NULL || cie == &bad_cie)
- return;
+ goto ret_err;
ptrType = fde_pointer_type(cie);
if (ptrType < 0)
- return;
+ goto ret_err;
ptr = (const u8 *)(fde + 2);
if (!read_pointer(&ptr, (const u8 *)(fde + 1) + *fde,
}
if (tableSize || !n)
- return;
+ goto ret_err;
hdrSize = 4 + sizeof(unsigned long) + sizeof(unsigned int)
+ 2 * n * sizeof(unsigned long);
+
header = alloc(hdrSize);
if (!header)
- return;
+ goto ret_err;
+
header->version = 1;
header->eh_frame_ptr_enc = DW_EH_PE_abs | DW_EH_PE_native;
header->fde_count_enc = DW_EH_PE_abs | DW_EH_PE_data4;
table->hdrsz = hdrSize;
smp_wmb();
table->header = (const void *)header;
-}
-
-static void *__init balloc(unsigned long sz)
-{
- return __alloc_bootmem_nopanic(sz,
- sizeof(unsigned int),
- __pa(MAX_DMA_ADDRESS));
-}
+ return;
-void __init arc_unwind_setup(void)
-{
- setup_unwind_table(&root_table, balloc);
+ret_err:
+ panic("Attention !!! Dwarf FDE parsing errors\n");;
}
#ifdef CONFIG_MODULES
table_start, table_size,
NULL, 0);
+ init_unwind_hdr(table, unw_hdr_alloc);
+
#ifdef UNWIND_DEBUG
unw_debug("Table added for [%s] %lx %lx\n",
module->name, table->core.pc, table->core.range);
info.init_only = init_only;
unlink_table(&info); /* XXX: SMP */
+ kfree(table->header);
kfree(table);
}
const u8 *ptr = (const u8 *)(cie + 2);
unsigned version = *ptr;
- if (version != 1)
- return -1; /* unsupported */
-
if (*++ptr) {
const char *aug;
const u8 *end = (const u8 *)(cie + 1) + *cie;
ptr = (const u8 *)(cie + 2);
end = (const u8 *)(cie + 1) + *cie;
frame->call_frame = 1;
- if ((state.version = *ptr) != 1)
- cie = NULL; /* unsupported version */
- else if (*++ptr) {
+ if (*++ptr) {
/* check if augmentation size is first (thus present) */
if (*ptr == 'z') {
while (++ptr < end && *ptr) {
}
EXPORT_SYMBOL(__kunmap_atomic);
-noinline pte_t *alloc_kmap_pgtable(unsigned long kvaddr)
+static noinline pte_t * __init alloc_kmap_pgtable(unsigned long kvaddr)
{
pgd_t *pgd_k;
pud_t *pud_k;
return pte_k;
}
-void kmap_init(void)
+void __init kmap_init(void)
{
/* Due to recursive include hell, we can't do this in processor.h */
BUILD_BUG_ON(PAGE_OFFSET < (VMALLOC_END + FIXMAP_SIZE + PKMAP_SIZE));
int in_use = 0;
if (!low_mem_sz) {
- BUG_ON(base != low_mem_start);
+ if (base != low_mem_start)
+ panic("CONFIG_LINUX_LINK_BASE != DT memory { }");
+
low_mem_sz = size;
in_use = 1;
} else {
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
&clks {
assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
<&clks IMX6QDL_PLL4_BYPASS>,
- <&clks IMX6QDL_CLK_PLL4_POST_DIV>,
<&clks IMX6QDL_CLK_LDB_DI0_SEL>,
- <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_PLL4_POST_DIV>;
assigned-clock-parents = <&clks IMX6QDL_CLK_LVDS2_IN>,
<&clks IMX6QDL_PLL4_BYPASS_SRC>,
<&clks IMX6QDL_CLK_PLL3_USB_OTG>,
<&clks IMX6QDL_CLK_PLL3_USB_OTG>;
- assigned-clock-rates = <0>, <0>, <24576000>;
+ assigned-clock-rates = <0>, <0>, <0>, <0>, <24576000>;
};
&ecspi1 {
};
};
+&uart3 {
+ interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
+ &omap4_pmx_core OMAP4_UART3_RX>;
+};
reg = <0x5d>;
interrupt-parent = <&pio>;
interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */
+ touchscreen-swapped-x-y;
};
};
/* CPU DFLL clock */
clock@0,70110000 {
- status = "okay";
+ status = "disabled";
vdd-cpu-supply = <&vdd_cpu>;
nvidia,i2c-fs-rate = <400000>;
};
select MACH_OMAP_GENERIC
select MIGHT_HAVE_CACHE_L2X0
select HAVE_ARM_SCU
+ select GENERIC_CLOCKEVENTS_BROADCAST
+ select HAVE_ARM_TWD
config SOC_DRA7XX
bool "TI DRA7XX"
return r;
}
+#if !defined(CONFIG_SMP) && defined(CONFIG_GENERIC_CLOCKEVENTS_BROADCAST)
+void tick_broadcast(const struct cpumask *mask)
+{
+}
+#endif
+
static void __init omap2_gp_clockevent_init(int gptimer_id,
const char *fck_source,
const char *property)
* On error, the variable @x is set to zero.
*/
#define __get_user_unaligned(x,ptr) \
- __get_user__unalignednocheck((x),(ptr),sizeof(*(ptr)))
+ __get_user_unaligned_nocheck((x),(ptr),sizeof(*(ptr)))
/*
* Yuck. We need two variants, one for 64bit operation and one
do { \
switch (size) { \
case 1: __get_data_asm(val, "lb", ptr); break; \
- case 2: __get_user_unaligned_asm(val, "ulh", ptr); break; \
- case 4: __get_user_unaligned_asm(val, "ulw", ptr); break; \
+ case 2: __get_data_unaligned_asm(val, "ulh", ptr); break; \
+ case 4: __get_data_unaligned_asm(val, "ulw", ptr); break; \
case 8: __GET_USER_UNALIGNED_DW(val, ptr); break; \
default: __get_user_unaligned_unknown(); break; \
} \
__cu_to = (to); \
__cu_from = (from); \
__cu_len = (n); \
- might_fault(); \
- __cu_len = __invoke_copy_from_user(__cu_to, __cu_from, \
- __cu_len); \
+ if (eva_kernel_access()) { \
+ __cu_len = __invoke_copy_from_kernel(__cu_to, \
+ __cu_from, \
+ __cu_len); \
+ } else { \
+ might_fault(); \
+ __cu_len = __invoke_copy_from_user(__cu_to, __cu_from, \
+ __cu_len); \
+ } \
__cu_len; \
})
{
__kernel_size_t res;
- might_fault();
- __asm__ __volatile__(
- "move\t$4, %1\n\t"
- "move\t$5, $0\n\t"
- "move\t$6, %2\n\t"
- __MODULE_JAL(__bzero)
- "move\t%0, $6"
- : "=r" (res)
- : "r" (addr), "r" (size)
- : "$4", "$5", "$6", __UA_t0, __UA_t1, "$31");
+ if (eva_kernel_access()) {
+ __asm__ __volatile__(
+ "move\t$4, %1\n\t"
+ "move\t$5, $0\n\t"
+ "move\t$6, %2\n\t"
+ __MODULE_JAL(__bzero_kernel)
+ "move\t%0, $6"
+ : "=r" (res)
+ : "r" (addr), "r" (size)
+ : "$4", "$5", "$6", __UA_t0, __UA_t1, "$31");
+ } else {
+ might_fault();
+ __asm__ __volatile__(
+ "move\t$4, %1\n\t"
+ "move\t$5, $0\n\t"
+ "move\t$6, %2\n\t"
+ __MODULE_JAL(__bzero)
+ "move\t%0, $6"
+ : "=r" (res)
+ : "r" (addr), "r" (size)
+ : "$4", "$5", "$6", __UA_t0, __UA_t1, "$31");
+ }
return res;
}
might_fault();
__asm__ __volatile__(
"move\t$4, %1\n\t"
- __MODULE_JAL(__strlen_kernel_asm)
+ __MODULE_JAL(__strlen_user_asm)
"move\t%0, $2"
: "=r" (res)
: "r" (s)
has_mt t0, 3f
.set push
- .set mips64r2
.set mt
/* Only allow 1 TC per VPE to execute... */
nop
.set push
- .set mips64r2
.set mt
1: /* Enter VPE configuration state */
#include <asm/fpu.h>
#include <asm/msa.h>
+extern void *__bzero_kernel(void *__s, size_t __count);
extern void *__bzero(void *__s, size_t __count);
extern long __strncpy_from_kernel_nocheck_asm(char *__to,
const char *__from, long __len);
EXPORT_SYMBOL(__copy_in_user_eva);
EXPORT_SYMBOL(__copy_to_user_eva);
EXPORT_SYMBOL(__copy_user_inatomic_eva);
+EXPORT_SYMBOL(__bzero_kernel);
#endif
EXPORT_SYMBOL(__bzero);
EXPORT_SYMBOL(__strncpy_from_kernel_nocheck_asm);
1:
#ifndef CONFIG_EVA
FEXPORT(__bzero)
+#else
+FEXPORT(__bzero_kernel)
#endif
__BUILD_BZERO LEGACY_MODE
static int rt288x_pci_probe(struct platform_device *pdev)
{
void __iomem *io_map_base;
- int i;
rt2880_pci_base = ioremap_nocache(RT2880_PCI_BASE, PAGE_SIZE);
void msp7120_reset(void)
{
void *start, *end, *iptr;
- register int i;
/* Diasble all interrupts */
local_irq_disable();
/* XXX This ends up at the ARC firmware prompt ... */
void sni_machine_restart(char *command)
{
- int i, j;
+ int i;
/* This does a normal via the keyboard controller like a PC.
We can do that easier ... */
# the comments on that file.
#
ifndef CONFIG_CPU_MIPSR6
- ifeq ($(call ld-ifversion, -gt, 22400000, y),)
- $(warning MIPS VDSO requires binutils > 2.24)
+ ifeq ($(call ld-ifversion, -lt, 22500000, y),)
+ $(warning MIPS VDSO requires binutils >= 2.25)
obj-vdso-y := $(filter-out gettimeofday.o, $(obj-vdso-y))
ccflags-vdso += -DDISABLE_MIPS_VDSO
endif
regs->gr[28]);
}
+/*
+ * Check how the syscall number gets loaded into %r20 within
+ * the delay branch in userspace and adjust as needed.
+ */
+
+static void check_syscallno_in_delay_branch(struct pt_regs *regs)
+{
+ u32 opcode, source_reg;
+ u32 __user *uaddr;
+ int err;
+
+ /* Usually we don't have to restore %r20 (the system call number)
+ * because it gets loaded in the delay slot of the branch external
+ * instruction via the ldi instruction.
+ * In some cases a register-to-register copy instruction might have
+ * been used instead, in which case we need to copy the syscall
+ * number into the source register before returning to userspace.
+ */
+
+ /* A syscall is just a branch, so all we have to do is fiddle the
+ * return pointer so that the ble instruction gets executed again.
+ */
+ regs->gr[31] -= 8; /* delayed branching */
+
+ /* Get assembler opcode of code in delay branch */
+ uaddr = (unsigned int *) ((regs->gr[31] & ~3) + 4);
+ err = get_user(opcode, uaddr);
+ if (err)
+ return;
+
+ /* Check if delay branch uses "ldi int,%r20" */
+ if ((opcode & 0xffff0000) == 0x34140000)
+ return; /* everything ok, just return */
+
+ /* Check if delay branch uses "nop" */
+ if (opcode == INSN_NOP)
+ return;
+
+ /* Check if delay branch uses "copy %rX,%r20" */
+ if ((opcode & 0xffe0ffff) == 0x08000254) {
+ source_reg = (opcode >> 16) & 31;
+ regs->gr[source_reg] = regs->gr[20];
+ return;
+ }
+
+ pr_warn("syscall restart: %s (pid %d): unexpected opcode 0x%08x\n",
+ current->comm, task_pid_nr(current), opcode);
+}
+
static inline void
syscall_restart(struct pt_regs *regs, struct k_sigaction *ka)
{
}
/* fallthrough */
case -ERESTARTNOINTR:
- /* A syscall is just a branch, so all
- * we have to do is fiddle the return pointer.
- */
- regs->gr[31] -= 8; /* delayed branching */
+ check_syscallno_in_delay_branch(regs);
break;
}
}
}
case -ERESTARTNOHAND:
case -ERESTARTSYS:
- case -ERESTARTNOINTR: {
- /* Hooray for delayed branching. We don't
- * have to restore %r20 (the system call
- * number) because it gets loaded in the delay
- * slot of the branch external instruction.
- */
- regs->gr[31] -= 8;
+ case -ERESTARTNOINTR:
+ check_syscallno_in_delay_branch(regs);
return;
- }
default:
break;
}
PPC64ONLY(switch_endian)
SYSCALL_SPU(userfaultfd)
SYSCALL_SPU(membarrier)
-SYSCALL(semop)
-SYSCALL(semget)
-COMPAT_SYS(semctl)
-COMPAT_SYS(semtimedop)
-COMPAT_SYS(msgsnd)
-COMPAT_SYS(msgrcv)
-SYSCALL(msgget)
-COMPAT_SYS(msgctl)
-COMPAT_SYS(shmat)
-SYSCALL(shmdt)
-SYSCALL(shmget)
-COMPAT_SYS(shmctl)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
+SYSCALL(ni_syscall)
SYSCALL(mlock2)
#define __NR_switch_endian 363
#define __NR_userfaultfd 364
#define __NR_membarrier 365
-#define __NR_semop 366
-#define __NR_semget 367
-#define __NR_semctl 368
-#define __NR_semtimedop 369
-#define __NR_msgsnd 370
-#define __NR_msgrcv 371
-#define __NR_msgget 372
-#define __NR_msgctl 373
-#define __NR_shmat 374
-#define __NR_shmdt 375
-#define __NR_shmget 376
-#define __NR_shmctl 377
#define __NR_mlock2 378
#endif /* _UAPI_ASM_POWERPC_UNISTD_H_ */
static void kvmppc_set_msr_hv(struct kvm_vcpu *vcpu, u64 msr)
{
+ /*
+ * Check for illegal transactional state bit combination
+ * and if we find it, force the TS field to a safe state.
+ */
+ if ((msr & MSR_TS_MASK) == MSR_TS_MASK)
+ msr &= ~MSR_TS_MASK;
vcpu->arch.shregs.msr = msr;
kvmppc_end_cede(vcpu);
}
set_bit(d->hwirq, &opal_event_irqchip.mask);
opal_poll_events(&events);
- opal_handle_events(be64_to_cpu(events));
+ last_outstanding_events = be64_to_cpu(events);
+
+ /*
+ * We can't just handle the events now with opal_handle_events().
+ * If we did we would deadlock when opal_event_unmask() is called from
+ * handle_level_irq() with the irq descriptor lock held, because
+ * calling opal_handle_events() would call generic_handle_irq() and
+ * then handle_level_irq() which would try to take the descriptor lock
+ * again. Instead queue the events for later.
+ */
+ if (last_outstanding_events & opal_event_irqchip.mask)
+ /* Need to retrigger the interrupt */
+ irq_work_queue(&opal_event_irq_work);
}
static int opal_event_set_type(struct irq_data *d, unsigned int flow_type)
/* Sanity check */
if (type >= OPAL_MSG_TYPE_MAX) {
- pr_warning("%s: Unknown message type: %u\n", __func__, type);
+ pr_warn_once("%s: Unknown message type: %u\n", __func__, type);
return;
}
opal_message_do_notify(type, (void *)&msg);
}
if (separator)
ptr += sprintf(ptr, "%c", separator);
+ /*
+ * Use four '%' characters below because of the
+ * following two conversions:
+ *
+ * 1) sprintf: %%%%r -> %%r
+ * 2) printk : %%r -> %r
+ */
if (operand->flags & OPERAND_GPR)
- ptr += sprintf(ptr, "%%r%i", value);
+ ptr += sprintf(ptr, "%%%%r%i", value);
else if (operand->flags & OPERAND_FPR)
- ptr += sprintf(ptr, "%%f%i", value);
+ ptr += sprintf(ptr, "%%%%f%i", value);
else if (operand->flags & OPERAND_AR)
- ptr += sprintf(ptr, "%%a%i", value);
+ ptr += sprintf(ptr, "%%%%a%i", value);
else if (operand->flags & OPERAND_CR)
- ptr += sprintf(ptr, "%%c%i", value);
+ ptr += sprintf(ptr, "%%%%c%i", value);
else if (operand->flags & OPERAND_VR)
- ptr += sprintf(ptr, "%%v%i", value);
+ ptr += sprintf(ptr, "%%%%v%i", value);
else if (operand->flags & OPERAND_PCREL)
ptr += sprintf(ptr, "%lx", (signed int) value
+ addr);
* really available. So we simply advertise only "crypto" support.
*/
#define HWCAP_SPARC_CRYPTO 0x04000000 /* CRYPTO insns available */
+#define HWCAP_SPARC_ADI 0x08000000 /* ADI available */
#define CORE_DUMP_USE_REGSET
#define __NR_bpf 349
#define __NR_execveat 350
#define __NR_membarrier 351
+#define __NR_userfaultfd 352
-#define NR_syscalls 352
+#define NR_syscalls 353
/* Bitmask values returned from kern_features system call. */
#define KERN_FEATURE_MIXED_MODE_STACK 0x00000001
mov 1, %o0
ENDPROC(__retl_one)
+ENTRY(__retl_one_fp)
+ VISExitHalf
+ retl
+ mov 1, %o0
+ENDPROC(__retl_one_fp)
+
ENTRY(__ret_one_asi)
wr %g0, ASI_AIUS, %asi
ret
mov 1, %o0
ENDPROC(__retl_one_asi)
+ENTRY(__retl_one_asi_fp)
+ wr %g0, ASI_AIUS, %asi
+ VISExitHalf
+ retl
+ mov 1, %o0
+ENDPROC(__retl_one_asi_fp)
+
ENTRY(__retl_o1)
retl
mov %o1, %o0
void
perf_callchain_user(struct perf_callchain_entry *entry, struct pt_regs *regs)
{
+ u64 saved_fault_address = current_thread_info()->fault_address;
+ u8 saved_fault_code = get_thread_fault_code();
+ mm_segment_t old_fs;
+
perf_callchain_store(entry, regs->tpc);
if (!current->mm)
return;
+ old_fs = get_fs();
+ set_fs(USER_DS);
+
flushw_user();
pagefault_disable();
perf_callchain_user_64(entry, regs);
pagefault_enable();
+
+ set_fs(old_fs);
+ set_thread_fault_code(saved_fault_code);
+ current_thread_info()->fault_address = saved_fault_address;
}
andn %l1, %l4, %l1
srl %l4, 20, %l4
ba,pt %xcc, rtrap_no_irq_enable
- wrpr %l4, %pil
+ nop
+ /* Do not actually set the %pil here. We will do that
+ * below after we clear PSTATE_IE in the %pstate register.
+ * If we re-enable interrupts here, we can recurse down
+ * the hardirq stack potentially endlessly, causing a
+ * stack overflow.
+ */
.align 64
.globl rtrap_irq, rtrap, irqsz_patchme, rtrap_xcall
*/
"mul32", "div32", "fsmuld", "v8plus", "popc", "vis", "vis2",
"ASIBlkInit", "fmaf", "vis3", "hpc", "random", "trans", "fjfmau",
- "ima", "cspare", "pause", "cbcond",
+ "ima", "cspare", "pause", "cbcond", NULL /*reserved for crypto */,
+ "adp",
};
static const char *crypto_hwcaps[] = {
seq_puts(m, "cpucaps\t\t: ");
for (i = 0; i < ARRAY_SIZE(hwcaps); i++) {
unsigned long bit = 1UL << i;
- if (caps & bit) {
+ if (hwcaps[i] && (caps & bit)) {
seq_printf(m, "%s%s",
printed ? "," : "", hwcaps[i]);
printed++;
for (i = 0; i < ARRAY_SIZE(hwcaps); i++) {
unsigned long bit = 1UL << i;
- if (caps & bit)
+ if (hwcaps[i] && (caps & bit))
report_one_hwcap(&printed, hwcaps[i]);
}
if (caps & HWCAP_SPARC_CRYPTO)
for (i = 0; i < ARRAY_SIZE(hwcaps); i++) {
unsigned long bit = 1UL << i;
- if (!strcmp(prop, hwcaps[i])) {
+ if (hwcaps[i] && !strcmp(prop, hwcaps[i])) {
caps |= bit;
break;
}
/*335*/ .long sys_syncfs, sys_sendmmsg, sys_setns, sys_process_vm_readv, sys_process_vm_writev
/*340*/ .long sys_ni_syscall, sys_kcmp, sys_finit_module, sys_sched_setattr, sys_sched_getattr
/*345*/ .long sys_renameat2, sys_seccomp, sys_getrandom, sys_memfd_create, sys_bpf
-/*350*/ .long sys_execveat, sys_membarrier
+/*350*/ .long sys_execveat, sys_membarrier, sys_userfaultfd
.word sys_syncfs, compat_sys_sendmmsg, sys_setns, compat_sys_process_vm_readv, compat_sys_process_vm_writev
/*340*/ .word sys_kern_features, sys_kcmp, sys_finit_module, sys_sched_setattr, sys_sched_getattr
.word sys32_renameat2, sys_seccomp, sys_getrandom, sys_memfd_create, sys_bpf
-/*350*/ .word sys32_execveat, sys_membarrier
+/*350*/ .word sys32_execveat, sys_membarrier, sys_userfaultfd
#endif /* CONFIG_COMPAT */
.word sys_syncfs, sys_sendmmsg, sys_setns, sys_process_vm_readv, sys_process_vm_writev
/*340*/ .word sys_kern_features, sys_kcmp, sys_finit_module, sys_sched_setattr, sys_sched_getattr
.word sys_renameat2, sys_seccomp, sys_getrandom, sys_memfd_create, sys_bpf
-/*350*/ .word sys64_execveat, sys_membarrier
+/*350*/ .word sys64_execveat, sys_membarrier, sys_userfaultfd
.text; \
.align 4;
+#define EX_LD_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_asi_fp;\
+ .text; \
+ .align 4;
+
#ifndef ASI_AIUS
#define ASI_AIUS 0x11
#endif
.text; \
.align 4;
+#define EX_ST_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_asi_fp;\
+ .text; \
+ .align 4;
+
#ifndef ASI_AIUS
#define ASI_AIUS 0x11
#endif
#ifndef EX_LD
#define EX_LD(x) x
#endif
+#ifndef EX_LD_FP
+#define EX_LD_FP(x) x
+#endif
#ifndef EX_ST
#define EX_ST(x) x
#endif
+#ifndef EX_ST_FP
+#define EX_ST_FP(x) x
+#endif
#ifndef EX_RETVAL
#define EX_RETVAL(x) x
fsrc2 %x6, %f12; \
fsrc2 %x7, %f14;
#define FREG_LOAD_1(base, x0) \
- EX_LD(LOAD(ldd, base + 0x00, %x0))
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0))
#define FREG_LOAD_2(base, x0, x1) \
- EX_LD(LOAD(ldd, base + 0x00, %x0)); \
- EX_LD(LOAD(ldd, base + 0x08, %x1));
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0)); \
+ EX_LD_FP(LOAD(ldd, base + 0x08, %x1));
#define FREG_LOAD_3(base, x0, x1, x2) \
- EX_LD(LOAD(ldd, base + 0x00, %x0)); \
- EX_LD(LOAD(ldd, base + 0x08, %x1)); \
- EX_LD(LOAD(ldd, base + 0x10, %x2));
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0)); \
+ EX_LD_FP(LOAD(ldd, base + 0x08, %x1)); \
+ EX_LD_FP(LOAD(ldd, base + 0x10, %x2));
#define FREG_LOAD_4(base, x0, x1, x2, x3) \
- EX_LD(LOAD(ldd, base + 0x00, %x0)); \
- EX_LD(LOAD(ldd, base + 0x08, %x1)); \
- EX_LD(LOAD(ldd, base + 0x10, %x2)); \
- EX_LD(LOAD(ldd, base + 0x18, %x3));
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0)); \
+ EX_LD_FP(LOAD(ldd, base + 0x08, %x1)); \
+ EX_LD_FP(LOAD(ldd, base + 0x10, %x2)); \
+ EX_LD_FP(LOAD(ldd, base + 0x18, %x3));
#define FREG_LOAD_5(base, x0, x1, x2, x3, x4) \
- EX_LD(LOAD(ldd, base + 0x00, %x0)); \
- EX_LD(LOAD(ldd, base + 0x08, %x1)); \
- EX_LD(LOAD(ldd, base + 0x10, %x2)); \
- EX_LD(LOAD(ldd, base + 0x18, %x3)); \
- EX_LD(LOAD(ldd, base + 0x20, %x4));
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0)); \
+ EX_LD_FP(LOAD(ldd, base + 0x08, %x1)); \
+ EX_LD_FP(LOAD(ldd, base + 0x10, %x2)); \
+ EX_LD_FP(LOAD(ldd, base + 0x18, %x3)); \
+ EX_LD_FP(LOAD(ldd, base + 0x20, %x4));
#define FREG_LOAD_6(base, x0, x1, x2, x3, x4, x5) \
- EX_LD(LOAD(ldd, base + 0x00, %x0)); \
- EX_LD(LOAD(ldd, base + 0x08, %x1)); \
- EX_LD(LOAD(ldd, base + 0x10, %x2)); \
- EX_LD(LOAD(ldd, base + 0x18, %x3)); \
- EX_LD(LOAD(ldd, base + 0x20, %x4)); \
- EX_LD(LOAD(ldd, base + 0x28, %x5));
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0)); \
+ EX_LD_FP(LOAD(ldd, base + 0x08, %x1)); \
+ EX_LD_FP(LOAD(ldd, base + 0x10, %x2)); \
+ EX_LD_FP(LOAD(ldd, base + 0x18, %x3)); \
+ EX_LD_FP(LOAD(ldd, base + 0x20, %x4)); \
+ EX_LD_FP(LOAD(ldd, base + 0x28, %x5));
#define FREG_LOAD_7(base, x0, x1, x2, x3, x4, x5, x6) \
- EX_LD(LOAD(ldd, base + 0x00, %x0)); \
- EX_LD(LOAD(ldd, base + 0x08, %x1)); \
- EX_LD(LOAD(ldd, base + 0x10, %x2)); \
- EX_LD(LOAD(ldd, base + 0x18, %x3)); \
- EX_LD(LOAD(ldd, base + 0x20, %x4)); \
- EX_LD(LOAD(ldd, base + 0x28, %x5)); \
- EX_LD(LOAD(ldd, base + 0x30, %x6));
+ EX_LD_FP(LOAD(ldd, base + 0x00, %x0)); \
+ EX_LD_FP(LOAD(ldd, base + 0x08, %x1)); \
+ EX_LD_FP(LOAD(ldd, base + 0x10, %x2)); \
+ EX_LD_FP(LOAD(ldd, base + 0x18, %x3)); \
+ EX_LD_FP(LOAD(ldd, base + 0x20, %x4)); \
+ EX_LD_FP(LOAD(ldd, base + 0x28, %x5)); \
+ EX_LD_FP(LOAD(ldd, base + 0x30, %x6));
.register %g2,#scratch
.register %g3,#scratch
nop
/* fall through for 0 < low bits < 8 */
110: sub %o4, 64, %g2
- EX_LD(LOAD_BLK(%g2, %f0))
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+ EX_LD_FP(LOAD_BLK(%g2, %f0))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f4, f6, f8, f10, f12, f14, f16)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_8(f16, f18, f20, f22, f24, f26, f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
120: sub %o4, 56, %g2
FREG_LOAD_7(%g2, f0, f2, f4, f6, f8, f10, f12)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f4, f6, f8, f10, f12, f16, f18)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_7(f18, f20, f22, f24, f26, f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
130: sub %o4, 48, %g2
FREG_LOAD_6(%g2, f0, f2, f4, f6, f8, f10)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f4, f6, f8, f10, f16, f18, f20)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_6(f20, f22, f24, f26, f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
140: sub %o4, 40, %g2
FREG_LOAD_5(%g2, f0, f2, f4, f6, f8)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f4, f6, f8, f16, f18, f20, f22)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_5(f22, f24, f26, f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
150: sub %o4, 32, %g2
FREG_LOAD_4(%g2, f0, f2, f4, f6)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f4, f6, f16, f18, f20, f22, f24)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_4(f24, f26, f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
160: sub %o4, 24, %g2
FREG_LOAD_3(%g2, f0, f2, f4)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f4, f16, f18, f20, f22, f24, f26)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_3(f26, f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
170: sub %o4, 16, %g2
FREG_LOAD_2(%g2, f0, f2)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f2, f16, f18, f20, f22, f24, f26, f28)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_2(f28, f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
180: sub %o4, 8, %g2
FREG_LOAD_1(%g2, f0)
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
- EX_LD(LOAD_BLK(%o4, %f16))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f16))
FREG_FROB(f0, f16, f18, f20, f22, f24, f26, f28, f30)
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
FREG_MOVE_1(f30)
subcc %g1, 64, %g1
add %o4, 64, %o4
nop
190:
-1: EX_ST(STORE_INIT(%g0, %o4 + %g3))
+1: EX_ST_FP(STORE_INIT(%g0, %o4 + %g3))
subcc %g1, 64, %g1
- EX_LD(LOAD_BLK(%o4, %f0))
- EX_ST(STORE_BLK(%f0, %o4 + %g3))
+ EX_LD_FP(LOAD_BLK(%o4, %f0))
+ EX_ST_FP(STORE_BLK(%f0, %o4 + %g3))
add %o4, 64, %o4
bne,pt %xcc, 1b
LOAD(prefetch, %o4 + 64, #one_read)
.text; \
.align 4;
+#define EX_LD_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_asi_fp;\
+ .text; \
+ .align 4;
+
#ifndef ASI_AIUS
#define ASI_AIUS 0x11
#endif
.text; \
.align 4;
+#define EX_ST_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_asi_fp;\
+ .text; \
+ .align 4;
+
#ifndef ASI_AIUS
#define ASI_AIUS 0x11
#endif
#ifndef EX_LD
#define EX_LD(x) x
#endif
+#ifndef EX_LD_FP
+#define EX_LD_FP(x) x
+#endif
#ifndef EX_ST
#define EX_ST(x) x
#endif
+#ifndef EX_ST_FP
+#define EX_ST_FP(x) x
+#endif
#ifndef EX_RETVAL
#define EX_RETVAL(x) x
sub %o2, %o4, %o2
alignaddr %o1, %g0, %g1
add %o1, %o4, %o1
- EX_LD(LOAD(ldd, %g1 + 0x00, %f0))
-1: EX_LD(LOAD(ldd, %g1 + 0x08, %f2))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x00, %f0))
+1: EX_LD_FP(LOAD(ldd, %g1 + 0x08, %f2))
subcc %o4, 0x40, %o4
- EX_LD(LOAD(ldd, %g1 + 0x10, %f4))
- EX_LD(LOAD(ldd, %g1 + 0x18, %f6))
- EX_LD(LOAD(ldd, %g1 + 0x20, %f8))
- EX_LD(LOAD(ldd, %g1 + 0x28, %f10))
- EX_LD(LOAD(ldd, %g1 + 0x30, %f12))
- EX_LD(LOAD(ldd, %g1 + 0x38, %f14))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x10, %f4))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x18, %f6))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x20, %f8))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x28, %f10))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x30, %f12))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x38, %f14))
faligndata %f0, %f2, %f16
- EX_LD(LOAD(ldd, %g1 + 0x40, %f0))
+ EX_LD_FP(LOAD(ldd, %g1 + 0x40, %f0))
faligndata %f2, %f4, %f18
add %g1, 0x40, %g1
faligndata %f4, %f6, %f20
faligndata %f10, %f12, %f26
faligndata %f12, %f14, %f28
faligndata %f14, %f0, %f30
- EX_ST(STORE(std, %f16, %o0 + 0x00))
- EX_ST(STORE(std, %f18, %o0 + 0x08))
- EX_ST(STORE(std, %f20, %o0 + 0x10))
- EX_ST(STORE(std, %f22, %o0 + 0x18))
- EX_ST(STORE(std, %f24, %o0 + 0x20))
- EX_ST(STORE(std, %f26, %o0 + 0x28))
- EX_ST(STORE(std, %f28, %o0 + 0x30))
- EX_ST(STORE(std, %f30, %o0 + 0x38))
+ EX_ST_FP(STORE(std, %f16, %o0 + 0x00))
+ EX_ST_FP(STORE(std, %f18, %o0 + 0x08))
+ EX_ST_FP(STORE(std, %f20, %o0 + 0x10))
+ EX_ST_FP(STORE(std, %f22, %o0 + 0x18))
+ EX_ST_FP(STORE(std, %f24, %o0 + 0x20))
+ EX_ST_FP(STORE(std, %f26, %o0 + 0x28))
+ EX_ST_FP(STORE(std, %f28, %o0 + 0x30))
+ EX_ST_FP(STORE(std, %f30, %o0 + 0x38))
add %o0, 0x40, %o0
bne,pt %icc, 1b
LOAD(prefetch, %g1 + 0x200, #n_reads_strong)
.text; \
.align 4;
+#define EX_LD_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_fp;\
+ .text; \
+ .align 4;
+
#define FUNC_NAME ___copy_from_user
#define LOAD(type,addr,dest) type##a [addr] %asi, dest
#define LOAD_BLK(addr,dest) ldda [addr] ASI_BLK_AIUS, dest
.text; \
.align 4;
+#define EX_ST_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_fp;\
+ .text; \
+ .align 4;
+
#define FUNC_NAME ___copy_to_user
#define STORE(type,src,addr) type##a src, [addr] ASI_AIUS
#define STORE_BLK(src,addr) stda src, [addr] ASI_BLK_AIUS
#ifndef EX_LD
#define EX_LD(x) x
#endif
+#ifndef EX_LD_FP
+#define EX_LD_FP(x) x
+#endif
#ifndef EX_ST
#define EX_ST(x) x
#endif
+#ifndef EX_ST_FP
+#define EX_ST_FP(x) x
+#endif
#ifndef EX_RETVAL
#define EX_RETVAL(x) x
faligndata %f8, %f9, %f62;
#define MAIN_LOOP_CHUNK(src, dest, fdest, fsrc, len, jmptgt) \
- EX_LD(LOAD_BLK(%src, %fdest)); \
- EX_ST(STORE_BLK(%fsrc, %dest)); \
+ EX_LD_FP(LOAD_BLK(%src, %fdest)); \
+ EX_ST_FP(STORE_BLK(%fsrc, %dest)); \
add %src, 0x40, %src; \
subcc %len, 0x40, %len; \
be,pn %xcc, jmptgt; \
#define DO_SYNC membar #Sync;
#define STORE_SYNC(dest, fsrc) \
- EX_ST(STORE_BLK(%fsrc, %dest)); \
+ EX_ST_FP(STORE_BLK(%fsrc, %dest)); \
add %dest, 0x40, %dest; \
DO_SYNC
#define STORE_JUMP(dest, fsrc, target) \
- EX_ST(STORE_BLK(%fsrc, %dest)); \
+ EX_ST_FP(STORE_BLK(%fsrc, %dest)); \
add %dest, 0x40, %dest; \
ba,pt %xcc, target; \
nop;
subcc %left, 8, %left;\
bl,pn %xcc, 95f; \
faligndata %f0, %f1, %f48; \
- EX_ST(STORE(std, %f48, %dest)); \
+ EX_ST_FP(STORE(std, %f48, %dest)); \
add %dest, 8, %dest;
#define UNEVEN_VISCHUNK_LAST(dest, f0, f1, left) \
and %g2, 0x38, %g2
1: subcc %g1, 0x1, %g1
- EX_LD(LOAD(ldub, %o1 + 0x00, %o3))
- EX_ST(STORE(stb, %o3, %o1 + %GLOBAL_SPARE))
+ EX_LD_FP(LOAD(ldub, %o1 + 0x00, %o3))
+ EX_ST_FP(STORE(stb, %o3, %o1 + %GLOBAL_SPARE))
bgu,pt %XCC, 1b
add %o1, 0x1, %o1
be,pt %icc, 3f
alignaddr %o1, %g0, %o1
- EX_LD(LOAD(ldd, %o1, %f4))
-1: EX_LD(LOAD(ldd, %o1 + 0x8, %f6))
+ EX_LD_FP(LOAD(ldd, %o1, %f4))
+1: EX_LD_FP(LOAD(ldd, %o1 + 0x8, %f6))
add %o1, 0x8, %o1
subcc %g2, 0x8, %g2
faligndata %f4, %f6, %f0
- EX_ST(STORE(std, %f0, %o0))
+ EX_ST_FP(STORE(std, %f0, %o0))
be,pn %icc, 3f
add %o0, 0x8, %o0
- EX_LD(LOAD(ldd, %o1 + 0x8, %f4))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x8, %f4))
add %o1, 0x8, %o1
subcc %g2, 0x8, %g2
faligndata %f6, %f4, %f0
- EX_ST(STORE(std, %f0, %o0))
+ EX_ST_FP(STORE(std, %f0, %o0))
bne,pt %icc, 1b
add %o0, 0x8, %o0
add %g1, %GLOBAL_SPARE, %g1
subcc %o2, %g3, %o2
- EX_LD(LOAD_BLK(%o1, %f0))
+ EX_LD_FP(LOAD_BLK(%o1, %f0))
add %o1, 0x40, %o1
add %g1, %g3, %g1
- EX_LD(LOAD_BLK(%o1, %f16))
+ EX_LD_FP(LOAD_BLK(%o1, %f16))
add %o1, 0x40, %o1
sub %GLOBAL_SPARE, 0x80, %GLOBAL_SPARE
- EX_LD(LOAD_BLK(%o1, %f32))
+ EX_LD_FP(LOAD_BLK(%o1, %f32))
add %o1, 0x40, %o1
/* There are 8 instances of the unrolled loop,
62: FINISH_VISCHUNK(o0, f44, f46, g3)
63: UNEVEN_VISCHUNK_LAST(o0, f46, f0, g3)
-93: EX_LD(LOAD(ldd, %o1, %f2))
+93: EX_LD_FP(LOAD(ldd, %o1, %f2))
add %o1, 8, %o1
subcc %g3, 8, %g3
faligndata %f0, %f2, %f8
- EX_ST(STORE(std, %f8, %o0))
+ EX_ST_FP(STORE(std, %f8, %o0))
bl,pn %xcc, 95f
add %o0, 8, %o0
- EX_LD(LOAD(ldd, %o1, %f0))
+ EX_LD_FP(LOAD(ldd, %o1, %f0))
add %o1, 8, %o1
subcc %g3, 8, %g3
faligndata %f2, %f0, %f8
- EX_ST(STORE(std, %f8, %o0))
+ EX_ST_FP(STORE(std, %f8, %o0))
bge,pt %xcc, 93b
add %o0, 8, %o0
95: brz,pt %o2, 2f
mov %g1, %o1
-1: EX_LD(LOAD(ldub, %o1, %o3))
+1: EX_LD_FP(LOAD(ldub, %o1, %o3))
add %o1, 1, %o1
subcc %o2, 1, %o2
- EX_ST(STORE(stb, %o3, %o0))
+ EX_ST_FP(STORE(stb, %o3, %o0))
bne,pt %xcc, 1b
add %o0, 1, %o0
.text; \
.align 4;
+#define EX_LD_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_fp;\
+ .text; \
+ .align 4;
+
#define FUNC_NAME U3copy_from_user
#define LOAD(type,addr,dest) type##a [addr] %asi, dest
#define EX_RETVAL(x) 0
.text; \
.align 4;
+#define EX_ST_FP(x) \
+98: x; \
+ .section __ex_table,"a";\
+ .align 4; \
+ .word 98b, __retl_one_fp;\
+ .text; \
+ .align 4;
+
#define FUNC_NAME U3copy_to_user
#define STORE(type,src,addr) type##a src, [addr] ASI_AIUS
#define STORE_BLK(src,addr) stda src, [addr] ASI_BLK_AIUS
#ifndef EX_LD
#define EX_LD(x) x
#endif
+#ifndef EX_LD_FP
+#define EX_LD_FP(x) x
+#endif
#ifndef EX_ST
#define EX_ST(x) x
#endif
+#ifndef EX_ST_FP
+#define EX_ST_FP(x) x
+#endif
#ifndef EX_RETVAL
#define EX_RETVAL(x) x
and %g2, 0x38, %g2
1: subcc %g1, 0x1, %g1
- EX_LD(LOAD(ldub, %o1 + 0x00, %o3))
- EX_ST(STORE(stb, %o3, %o1 + GLOBAL_SPARE))
+ EX_LD_FP(LOAD(ldub, %o1 + 0x00, %o3))
+ EX_ST_FP(STORE(stb, %o3, %o1 + GLOBAL_SPARE))
bgu,pt %XCC, 1b
add %o1, 0x1, %o1
be,pt %icc, 3f
alignaddr %o1, %g0, %o1
- EX_LD(LOAD(ldd, %o1, %f4))
-1: EX_LD(LOAD(ldd, %o1 + 0x8, %f6))
+ EX_LD_FP(LOAD(ldd, %o1, %f4))
+1: EX_LD_FP(LOAD(ldd, %o1 + 0x8, %f6))
add %o1, 0x8, %o1
subcc %g2, 0x8, %g2
faligndata %f4, %f6, %f0
- EX_ST(STORE(std, %f0, %o0))
+ EX_ST_FP(STORE(std, %f0, %o0))
be,pn %icc, 3f
add %o0, 0x8, %o0
- EX_LD(LOAD(ldd, %o1 + 0x8, %f4))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x8, %f4))
add %o1, 0x8, %o1
subcc %g2, 0x8, %g2
faligndata %f6, %f4, %f2
- EX_ST(STORE(std, %f2, %o0))
+ EX_ST_FP(STORE(std, %f2, %o0))
bne,pt %icc, 1b
add %o0, 0x8, %o0
LOAD(prefetch, %o1 + 0x080, #one_read)
LOAD(prefetch, %o1 + 0x0c0, #one_read)
LOAD(prefetch, %o1 + 0x100, #one_read)
- EX_LD(LOAD(ldd, %o1 + 0x000, %f0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x000, %f0))
LOAD(prefetch, %o1 + 0x140, #one_read)
- EX_LD(LOAD(ldd, %o1 + 0x008, %f2))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x008, %f2))
LOAD(prefetch, %o1 + 0x180, #one_read)
- EX_LD(LOAD(ldd, %o1 + 0x010, %f4))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x010, %f4))
LOAD(prefetch, %o1 + 0x1c0, #one_read)
faligndata %f0, %f2, %f16
- EX_LD(LOAD(ldd, %o1 + 0x018, %f6))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x018, %f6))
faligndata %f2, %f4, %f18
- EX_LD(LOAD(ldd, %o1 + 0x020, %f8))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x020, %f8))
faligndata %f4, %f6, %f20
- EX_LD(LOAD(ldd, %o1 + 0x028, %f10))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x028, %f10))
faligndata %f6, %f8, %f22
- EX_LD(LOAD(ldd, %o1 + 0x030, %f12))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x030, %f12))
faligndata %f8, %f10, %f24
- EX_LD(LOAD(ldd, %o1 + 0x038, %f14))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x038, %f14))
faligndata %f10, %f12, %f26
- EX_LD(LOAD(ldd, %o1 + 0x040, %f0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x040, %f0))
subcc GLOBAL_SPARE, 0x80, GLOBAL_SPARE
add %o1, 0x40, %o1
.align 64
1:
- EX_LD(LOAD(ldd, %o1 + 0x008, %f2))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x008, %f2))
faligndata %f12, %f14, %f28
- EX_LD(LOAD(ldd, %o1 + 0x010, %f4))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x010, %f4))
faligndata %f14, %f0, %f30
- EX_ST(STORE_BLK(%f16, %o0))
- EX_LD(LOAD(ldd, %o1 + 0x018, %f6))
+ EX_ST_FP(STORE_BLK(%f16, %o0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x018, %f6))
faligndata %f0, %f2, %f16
add %o0, 0x40, %o0
- EX_LD(LOAD(ldd, %o1 + 0x020, %f8))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x020, %f8))
faligndata %f2, %f4, %f18
- EX_LD(LOAD(ldd, %o1 + 0x028, %f10))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x028, %f10))
faligndata %f4, %f6, %f20
- EX_LD(LOAD(ldd, %o1 + 0x030, %f12))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x030, %f12))
subcc %o3, 0x01, %o3
faligndata %f6, %f8, %f22
- EX_LD(LOAD(ldd, %o1 + 0x038, %f14))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x038, %f14))
faligndata %f8, %f10, %f24
- EX_LD(LOAD(ldd, %o1 + 0x040, %f0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x040, %f0))
LOAD(prefetch, %o1 + 0x1c0, #one_read)
faligndata %f10, %f12, %f26
bg,pt %XCC, 1b
/* Finally we copy the last full 64-byte block. */
2:
- EX_LD(LOAD(ldd, %o1 + 0x008, %f2))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x008, %f2))
faligndata %f12, %f14, %f28
- EX_LD(LOAD(ldd, %o1 + 0x010, %f4))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x010, %f4))
faligndata %f14, %f0, %f30
- EX_ST(STORE_BLK(%f16, %o0))
- EX_LD(LOAD(ldd, %o1 + 0x018, %f6))
+ EX_ST_FP(STORE_BLK(%f16, %o0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x018, %f6))
faligndata %f0, %f2, %f16
- EX_LD(LOAD(ldd, %o1 + 0x020, %f8))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x020, %f8))
faligndata %f2, %f4, %f18
- EX_LD(LOAD(ldd, %o1 + 0x028, %f10))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x028, %f10))
faligndata %f4, %f6, %f20
- EX_LD(LOAD(ldd, %o1 + 0x030, %f12))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x030, %f12))
faligndata %f6, %f8, %f22
- EX_LD(LOAD(ldd, %o1 + 0x038, %f14))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x038, %f14))
faligndata %f8, %f10, %f24
cmp %g1, 0
be,pt %XCC, 1f
add %o0, 0x40, %o0
- EX_LD(LOAD(ldd, %o1 + 0x040, %f0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x040, %f0))
1: faligndata %f10, %f12, %f26
faligndata %f12, %f14, %f28
faligndata %f14, %f0, %f30
- EX_ST(STORE_BLK(%f16, %o0))
+ EX_ST_FP(STORE_BLK(%f16, %o0))
add %o0, 0x40, %o0
add %o1, 0x40, %o1
membar #Sync
sub %o2, %g2, %o2
be,a,pt %XCC, 1f
- EX_LD(LOAD(ldd, %o1 + 0x00, %f0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x00, %f0))
-1: EX_LD(LOAD(ldd, %o1 + 0x08, %f2))
+1: EX_LD_FP(LOAD(ldd, %o1 + 0x08, %f2))
add %o1, 0x8, %o1
subcc %g2, 0x8, %g2
faligndata %f0, %f2, %f8
- EX_ST(STORE(std, %f8, %o0))
+ EX_ST_FP(STORE(std, %f8, %o0))
be,pn %XCC, 2f
add %o0, 0x8, %o0
- EX_LD(LOAD(ldd, %o1 + 0x08, %f0))
+ EX_LD_FP(LOAD(ldd, %o1 + 0x08, %f0))
add %o1, 0x8, %o1
subcc %g2, 0x8, %g2
faligndata %f2, %f0, %f8
- EX_ST(STORE(std, %f8, %o0))
+ EX_ST_FP(STORE(std, %f8, %o0))
bne,pn %XCC, 1b
add %o0, 0x8, %o0
return best && (best->ecx & bit(X86_FEATURE_XSAVE));
}
+static inline bool guest_cpuid_has_mtrr(struct kvm_vcpu *vcpu)
+{
+ struct kvm_cpuid_entry2 *best;
+
+ best = kvm_find_cpuid_entry(vcpu, 1, 0);
+ return best && (best->edx & bit(X86_FEATURE_MTRR));
+}
+
static inline bool guest_cpuid_has_tsc_adjust(struct kvm_vcpu *vcpu)
{
struct kvm_cpuid_entry2 *best;
return mtrr_state->deftype & IA32_MTRR_DEF_TYPE_TYPE_MASK;
}
-static u8 mtrr_disabled_type(void)
+static u8 mtrr_disabled_type(struct kvm_vcpu *vcpu)
{
/*
* Intel SDM 11.11.2.2: all MTRRs are disabled when
* IA32_MTRR_DEF_TYPE.E bit is cleared, and the UC
* memory type is applied to all of physical memory.
+ *
+ * However, virtual machines can be run with CPUID such that
+ * there are no MTRRs. In that case, the firmware will never
+ * enable MTRRs and it is obviously undesirable to run the
+ * guest entirely with UC memory and we use WB.
*/
- return MTRR_TYPE_UNCACHABLE;
+ if (guest_cpuid_has_mtrr(vcpu))
+ return MTRR_TYPE_UNCACHABLE;
+ else
+ return MTRR_TYPE_WRBACK;
}
/*
for (seg = 0; seg < seg_num; seg++) {
mtrr_seg = &fixed_seg_table[seg];
- if (mtrr_seg->start >= addr && addr < mtrr_seg->end)
+ if (mtrr_seg->start <= addr && addr < mtrr_seg->end)
return seg;
}
*start = range->base & PAGE_MASK;
mask = range->mask & PAGE_MASK;
- mask |= ~0ULL << boot_cpu_data.x86_phys_bits;
/* This cannot overflow because writing to the reserved bits of
* variable MTRRs causes a #GP.
if (var_mtrr_range_is_valid(cur))
list_del(&mtrr_state->var_ranges[index].node);
+ /* Extend the mask with all 1 bits to the left, since those
+ * bits must implicitly be 0. The bits are then cleared
+ * when reading them.
+ */
if (!is_mtrr_mask)
cur->base = data;
else
- cur->mask = data;
+ cur->mask = data | (-1LL << cpuid_maxphyaddr(vcpu));
/* add it to the list if it's enabled. */
if (var_mtrr_range_is_valid(cur)) {
*pdata = vcpu->arch.mtrr_state.var_ranges[index].base;
else
*pdata = vcpu->arch.mtrr_state.var_ranges[index].mask;
+
+ *pdata &= (1ULL << cpuid_maxphyaddr(vcpu)) - 1;
}
return 0;
}
if (iter.mtrr_disabled)
- return mtrr_disabled_type();
+ return mtrr_disabled_type(vcpu);
/* not contained in any MTRRs. */
if (type == -1)
struct kvm_run *kvm_run = vcpu->run;
u32 exit_code = svm->vmcb->control.exit_code;
+ trace_kvm_exit(exit_code, vcpu, KVM_ISA_SVM);
+
if (!is_cr_intercept(svm, INTERCEPT_CR0_WRITE))
vcpu->arch.cr0 = svm->vmcb->save.cr0;
if (npt_enabled)
vcpu->arch.regs[VCPU_REGS_RSP] = svm->vmcb->save.rsp;
vcpu->arch.regs[VCPU_REGS_RIP] = svm->vmcb->save.rip;
- trace_kvm_exit(svm->vmcb->control.exit_code, vcpu, KVM_ISA_SVM);
-
if (unlikely(svm->vmcb->control.exit_code == SVM_EXIT_NMI))
kvm_before_handle_nmi(&svm->vcpu);
msr_info->data = vcpu->arch.ia32_xss;
break;
case MSR_TSC_AUX:
- if (!guest_cpuid_has_rdtscp(vcpu))
+ if (!guest_cpuid_has_rdtscp(vcpu) && !msr_info->host_initiated)
return 1;
/* Otherwise falls through */
default:
clear_atomic_switch_msr(vmx, MSR_IA32_XSS);
break;
case MSR_TSC_AUX:
- if (!guest_cpuid_has_rdtscp(vcpu))
+ if (!guest_cpuid_has_rdtscp(vcpu) && !msr_info->host_initiated)
return 1;
/* Check reserved bit, higher 32 bits should be zero */
if ((data >> 32) != 0)
u32 exit_reason = vmx->exit_reason;
u32 vectoring_info = vmx->idt_vectoring_info;
+ trace_kvm_exit(exit_reason, vcpu, KVM_ISA_VMX);
+
/*
* Flush logged GPAs PML buffer, this will make dirty_bitmap more
* updated. Another good is, in kvm_vm_ioctl_get_dirty_log, before
vmx->loaded_vmcs->launched = 1;
vmx->exit_reason = vmcs_read32(VM_EXIT_REASON);
- trace_kvm_exit(vmx->exit_reason, vcpu, KVM_ISA_VMX);
/*
* the KVM_REQ_EVENT optimization bit is only on for one entry, and if
static int kvm_vm_ioctl_set_pit(struct kvm *kvm, struct kvm_pit_state *ps)
{
+ int i;
mutex_lock(&kvm->arch.vpit->pit_state.lock);
memcpy(&kvm->arch.vpit->pit_state, ps, sizeof(struct kvm_pit_state));
- kvm_pit_load_count(kvm, 0, ps->channels[0].count, 0);
+ for (i = 0; i < 3; i++)
+ kvm_pit_load_count(kvm, i, ps->channels[i].count, 0);
mutex_unlock(&kvm->arch.vpit->pit_state.lock);
return 0;
}
static int kvm_vm_ioctl_set_pit2(struct kvm *kvm, struct kvm_pit_state2 *ps)
{
int start = 0;
+ int i;
u32 prev_legacy, cur_legacy;
mutex_lock(&kvm->arch.vpit->pit_state.lock);
prev_legacy = kvm->arch.vpit->pit_state.flags & KVM_PIT_FLAGS_HPET_LEGACY;
memcpy(&kvm->arch.vpit->pit_state.channels, &ps->channels,
sizeof(kvm->arch.vpit->pit_state.channels));
kvm->arch.vpit->pit_state.flags = ps->flags;
- kvm_pit_load_count(kvm, 0, kvm->arch.vpit->pit_state.channels[0].count, start);
+ for (i = 0; i < 3; i++)
+ kvm_pit_load_count(kvm, i, kvm->arch.vpit->pit_state.channels[i].count, start);
mutex_unlock(&kvm->arch.vpit->pit_state.lock);
return 0;
}
if (req_immediate_exit)
smp_send_reschedule(vcpu->cpu);
+ trace_kvm_entry(vcpu->vcpu_id);
+ wait_lapic_expire(vcpu);
__kvm_guest_enter();
if (unlikely(vcpu->arch.switch_db_regs)) {
vcpu->arch.switch_db_regs &= ~KVM_DEBUGREG_RELOAD;
}
- trace_kvm_entry(vcpu->vcpu_id);
- wait_lapic_expire(vcpu);
kvm_x86_ops->run(vcpu);
/*
struct sigcontext __user *sc = &frame->sc;
int sig_size = (_NSIG_WORDS - 1) * sizeof(unsigned long);
- if (copy_from_user(&set.sig[0], (void *)sc->oldmask, sizeof(set.sig[0])) ||
+ if (copy_from_user(&set.sig[0], &sc->oldmask, sizeof(set.sig[0])) ||
copy_from_user(&set.sig[1], frame->extramask, sig_size))
goto segfault;
{
x86_init.paging.pagetable_init = xen_pagetable_init;
- /* Optimization - we can use the HVM one but it has no idea which
- * VCPUs are descheduled - which means that it will needlessly IPI
- * them. Xen knows so let it do the job.
- */
- if (xen_feature(XENFEAT_auto_translated_physmap)) {
- pv_mmu_ops.flush_tlb_others = xen_flush_tlb_others;
+ if (xen_feature(XENFEAT_auto_translated_physmap))
return;
- }
+
pv_mmu_ops = xen_mmu_ops;
memset(dummy_mapping, 0xff, PAGE_SIZE);
void xen_arch_pre_suspend(void)
{
- int cpu;
-
- for_each_online_cpu(cpu)
- xen_pmu_finish(cpu);
-
if (xen_pv_domain())
xen_pv_pre_suspend();
}
void xen_arch_post_suspend(int cancelled)
{
- int cpu;
-
if (xen_pv_domain())
xen_pv_post_suspend(cancelled);
else
xen_hvm_post_suspend(cancelled);
-
- for_each_online_cpu(cpu)
- xen_pmu_init(cpu);
}
static void xen_vcpu_notify_restore(void *data)
void xen_arch_resume(void)
{
+ int cpu;
+
on_each_cpu(xen_vcpu_notify_restore, NULL, 1);
+
+ for_each_online_cpu(cpu)
+ xen_pmu_init(cpu);
}
void xen_arch_suspend(void)
{
+ int cpu;
+
+ for_each_online_cpu(cpu)
+ xen_pmu_finish(cpu);
+
on_each_cpu(xen_vcpu_notify_suspend, NULL, 1);
}
struct request *req;
unsigned int request_count = 0;
- blk_queue_split(q, &bio, q->bio_split);
-
/*
* low level driver can indicate that it wants pages above a
* certain limit bounced to low memory (ie for highmem, or even
*/
blk_queue_bounce(q, &bio);
+ blk_queue_split(q, &bio, q->bio_split);
+
if (bio_integrity_enabled(bio) && bio_integrity_prep(bio)) {
bio->bi_error = -EIO;
bio_endio(bio);
goto err_remove_sysfs_thermal;
}
- sysfs_remove_link(&pr->cdev->device.kobj, "device");
+ return 0;
+
err_remove_sysfs_thermal:
sysfs_remove_link(&device->dev.kobj, "thermal_cooling");
err_thermal_unregister:
struct generic_pm_domain *genpd;
bool (*stop_ok)(struct device *__dev);
struct gpd_timing_data *td = &dev_gpd_data(dev)->td;
+ bool runtime_pm = pm_runtime_enabled(dev);
ktime_t time_start;
s64 elapsed_ns;
int ret;
if (IS_ERR(genpd))
return -EINVAL;
+ /*
+ * A runtime PM centric subsystem/driver may re-use the runtime PM
+ * callbacks for other purposes than runtime PM. In those scenarios
+ * runtime PM is disabled. Under these circumstances, we shall skip
+ * validating/measuring the PM QoS latency.
+ */
stop_ok = genpd->gov ? genpd->gov->stop_ok : NULL;
- if (stop_ok && !stop_ok(dev))
+ if (runtime_pm && stop_ok && !stop_ok(dev))
return -EBUSY;
/* Measure suspend latency. */
- time_start = ktime_get();
+ if (runtime_pm)
+ time_start = ktime_get();
ret = genpd_save_dev(genpd, dev);
if (ret)
}
/* Update suspend latency value if the measured time exceeds it. */
- elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
- if (elapsed_ns > td->suspend_latency_ns) {
- td->suspend_latency_ns = elapsed_ns;
- dev_dbg(dev, "suspend latency exceeded, %lld ns\n",
- elapsed_ns);
- genpd->max_off_time_changed = true;
- td->constraint_changed = true;
+ if (runtime_pm) {
+ elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
+ if (elapsed_ns > td->suspend_latency_ns) {
+ td->suspend_latency_ns = elapsed_ns;
+ dev_dbg(dev, "suspend latency exceeded, %lld ns\n",
+ elapsed_ns);
+ genpd->max_off_time_changed = true;
+ td->constraint_changed = true;
+ }
}
/*
{
struct generic_pm_domain *genpd;
struct gpd_timing_data *td = &dev_gpd_data(dev)->td;
+ bool runtime_pm = pm_runtime_enabled(dev);
ktime_t time_start;
s64 elapsed_ns;
int ret;
out:
/* Measure resume latency. */
- if (timed)
+ if (timed && runtime_pm)
time_start = ktime_get();
genpd_start_dev(genpd, dev);
genpd_restore_dev(genpd, dev);
/* Update resume latency value if the measured time exceeds it. */
- if (timed) {
+ if (timed && runtime_pm) {
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
if (elapsed_ns > td->resume_latency_ns) {
td->resume_latency_ns = elapsed_ns;
{
struct request_queue *q = NULL;
+ if (cmd->rq)
+ q = cmd->rq->q;
+
switch (queue_mode) {
case NULL_Q_MQ:
blk_mq_end_request(cmd->rq, 0);
goto free_cmd;
}
- if (cmd->rq)
- q = cmd->rq->q;
-
/* Restart queue if needed, as we are freeing a tag */
if (q && !q->mq_ops && blk_queue_stopped(q)) {
unsigned long flags;
goto unmap;
for (n = 0, i = 0; n < nseg; n++) {
+ uint8_t first_sect, last_sect;
+
if ((n % SEGS_PER_INDIRECT_FRAME) == 0) {
/* Map indirect segments */
if (segments)
segments = kmap_atomic(pages[n/SEGS_PER_INDIRECT_FRAME]->page);
}
i = n % SEGS_PER_INDIRECT_FRAME;
+
pending_req->segments[n]->gref = segments[i].gref;
- seg[n].nsec = segments[i].last_sect -
- segments[i].first_sect + 1;
- seg[n].offset = (segments[i].first_sect << 9);
- if ((segments[i].last_sect >= (XEN_PAGE_SIZE >> 9)) ||
- (segments[i].last_sect < segments[i].first_sect)) {
+
+ first_sect = READ_ONCE(segments[i].first_sect);
+ last_sect = READ_ONCE(segments[i].last_sect);
+ if (last_sect >= (XEN_PAGE_SIZE >> 9) || last_sect < first_sect) {
rc = -EINVAL;
goto unmap;
}
+
+ seg[n].nsec = last_sect - first_sect + 1;
+ seg[n].offset = first_sect << 9;
preq->nr_sects += seg[n].nsec;
}
struct blkif_x86_32_request *src)
{
int i, n = BLKIF_MAX_SEGMENTS_PER_REQUEST, j;
- dst->operation = src->operation;
- switch (src->operation) {
+ dst->operation = READ_ONCE(src->operation);
+ switch (dst->operation) {
case BLKIF_OP_READ:
case BLKIF_OP_WRITE:
case BLKIF_OP_WRITE_BARRIER:
struct blkif_x86_64_request *src)
{
int i, n = BLKIF_MAX_SEGMENTS_PER_REQUEST, j;
- dst->operation = src->operation;
- switch (src->operation) {
+ dst->operation = READ_ONCE(src->operation);
+ switch (dst->operation) {
case BLKIF_OP_READ:
case BLKIF_OP_WRITE:
case BLKIF_OP_WRITE_BARRIER:
ret = _sunxi_rsb_run_xfer(rsb);
if (ret)
- goto out;
+ goto unlock;
*buf = readl(rsb->regs + RSB_DATA);
+unlock:
mutex_unlock(&rsb->lock);
-out:
return ret;
}
*/
static const struct sunxi_rsb_addr_map sunxi_rsb_addr_maps[] = {
- { 0x3e3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
+ { 0x3a3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
{ 0x745, 0x3a }, /* Secondary PMIC: AXP806, ... */
- { 0xe89, 0x45 }, /* Peripheral IC: AC100, ... */
+ { 0xe89, 0x4e }, /* Peripheral IC: AC100, ... */
};
static u8 sunxi_rsb_get_rtaddr(u16 hwaddr)
config ARM_TEGRA124_CPUFREQ
tristate "Tegra124 CPUFreq support"
- depends on ARCH_TEGRA && CPUFREQ_DT
+ depends on ARCH_TEGRA && CPUFREQ_DT && REGULATOR
default y
help
This adds the CPUFreq driver support for Tegra124 SOCs.
limits->max_sysfs_pct);
limits->max_perf_pct = max(limits->min_policy_pct,
limits->max_perf_pct);
- limits->max_perf = round_up(limits->max_perf, 8);
+ limits->max_perf = round_up(limits->max_perf, FRAC_BITS);
/* Make sure min_perf_pct <= max_perf_pct */
limits->min_perf_pct = min(limits->max_perf_pct, limits->min_perf_pct);
static struct scpi_dvfs_info *scpi_get_dvfs_info(struct device *cpu_dev)
{
- u8 domain = topology_physical_package_id(cpu_dev->id);
+ int domain = topology_physical_package_id(cpu_dev->id);
if (domain < 0)
return ERR_PTR(-EINVAL);
__raw_writel(BIT(offset), ctrl->base + AR71XX_GPIO_REG_CLEAR);
__raw_writel(
- __raw_readl(ctrl->base + AR71XX_GPIO_REG_OE) & BIT(offset),
+ __raw_readl(ctrl->base + AR71XX_GPIO_REG_OE) & ~BIT(offset),
ctrl->base + AR71XX_GPIO_REG_OE);
spin_unlock_irqrestore(&ctrl->lock, flags);
unsigned long pinmask = bgc->pin2mask(bgc, gpio);
if (bgc->dir & pinmask)
- return bgc->read_reg(bgc->reg_set) & pinmask;
+ return !!(bgc->read_reg(bgc->reg_set) & pinmask);
else
- return bgc->read_reg(bgc->reg_dat) & pinmask;
+ return !!(bgc->read_reg(bgc->reg_dat) & pinmask);
}
static int bgpio_get(struct gpio_chip *gc, unsigned int gpio)
chip = desc->chip;
offset = gpio_chip_hwgpio(desc);
value = chip->get ? chip->get(chip, offset) : -EIO;
- value = value < 0 ? value : !!value;
+ /*
+ * FIXME: fix all drivers to clamp to [0,1] or return negative,
+ * then change this to:
+ * value = value < 0 ? value : !!value;
+ * so we can properly propagate error codes.
+ */
+ value = !!value;
trace_gpio_value(desc_to_gpio(desc), 1, value);
return value;
}
struct ww_acquire_ctx ticket;
/* user fence */
- struct amdgpu_user_fence uf;
+ struct amdgpu_user_fence uf;
+ struct amdgpu_bo_list_entry uf_entry;
};
struct amdgpu_job {
return 0;
}
+static int amdgpu_cs_user_fence_chunk(struct amdgpu_cs_parser *p,
+ struct drm_amdgpu_cs_chunk_fence *fence_data)
+{
+ struct drm_gem_object *gobj;
+ uint32_t handle;
+
+ handle = fence_data->handle;
+ gobj = drm_gem_object_lookup(p->adev->ddev, p->filp,
+ fence_data->handle);
+ if (gobj == NULL)
+ return -EINVAL;
+
+ p->uf.bo = amdgpu_bo_ref(gem_to_amdgpu_bo(gobj));
+ p->uf.offset = fence_data->offset;
+
+ if (amdgpu_ttm_tt_has_userptr(p->uf.bo->tbo.ttm)) {
+ drm_gem_object_unreference_unlocked(gobj);
+ return -EINVAL;
+ }
+
+ p->uf_entry.robj = amdgpu_bo_ref(p->uf.bo);
+ p->uf_entry.prefered_domains = AMDGPU_GEM_DOMAIN_GTT;
+ p->uf_entry.allowed_domains = AMDGPU_GEM_DOMAIN_GTT;
+ p->uf_entry.priority = 0;
+ p->uf_entry.tv.bo = &p->uf_entry.robj->tbo;
+ p->uf_entry.tv.shared = true;
+
+ drm_gem_object_unreference_unlocked(gobj);
+ return 0;
+}
+
int amdgpu_cs_parser_init(struct amdgpu_cs_parser *p, void *data)
{
union drm_amdgpu_cs *cs = data;
case AMDGPU_CHUNK_ID_FENCE:
size = sizeof(struct drm_amdgpu_cs_chunk_fence);
- if (p->chunks[i].length_dw * sizeof(uint32_t) >= size) {
- uint32_t handle;
- struct drm_gem_object *gobj;
- struct drm_amdgpu_cs_chunk_fence *fence_data;
-
- fence_data = (void *)p->chunks[i].kdata;
- handle = fence_data->handle;
- gobj = drm_gem_object_lookup(p->adev->ddev,
- p->filp, handle);
- if (gobj == NULL) {
- ret = -EINVAL;
- goto free_partial_kdata;
- }
-
- p->uf.bo = gem_to_amdgpu_bo(gobj);
- amdgpu_bo_ref(p->uf.bo);
- drm_gem_object_unreference_unlocked(gobj);
- p->uf.offset = fence_data->offset;
- } else {
+ if (p->chunks[i].length_dw * sizeof(uint32_t) < size) {
ret = -EINVAL;
goto free_partial_kdata;
}
+
+ ret = amdgpu_cs_user_fence_chunk(p, (void *)p->chunks[i].kdata);
+ if (ret)
+ goto free_partial_kdata;
+
break;
case AMDGPU_CHUNK_ID_DEPENDENCIES:
p->vm_bos = amdgpu_vm_get_bos(p->adev, &fpriv->vm,
&p->validated);
+ if (p->uf.bo)
+ list_add(&p->uf_entry.tv.head, &p->validated);
+
if (need_mmap_lock)
down_read(¤t->mm->mmap_sem);
for (i = 0; i < parser->num_ibs; i++)
amdgpu_ib_free(parser->adev, &parser->ibs[i]);
kfree(parser->ibs);
- if (parser->uf.bo)
- amdgpu_bo_unref(&parser->uf.bo);
+ amdgpu_bo_unref(&parser->uf.bo);
+ amdgpu_bo_unref(&parser->uf_entry.robj);
}
static int amdgpu_bo_vm_update_pte(struct amdgpu_cs_parser *p,
{
struct exynos_drm_crtc *exynos_crtc = to_exynos_crtc(crtc);
+ if (!state->enable)
+ return 0;
+
if (exynos_crtc->ops->atomic_check)
return exynos_crtc->ops->atomic_check(exynos_crtc, state);
struct drm_i915_private *i915;
struct intel_engine_cs *ring;
- /** GEM sequence number associated with this request. */
- uint32_t seqno;
+ /** GEM sequence number associated with the previous request,
+ * when the HWS breadcrumb is equal to this the GPU is processing
+ * this request.
+ */
+ u32 previous_seqno;
+
+ /** GEM sequence number associated with this request,
+ * when the HWS breadcrumb is equal or greater than this the GPU
+ * has finished processing this request.
+ */
+ u32 seqno;
/** Position in the ringbuffer of the start of the request */
u32 head;
int i915_vma_bind(struct i915_vma *vma, enum i915_cache_level cache_level,
u32 flags);
+void __i915_vma_set_map_and_fenceable(struct i915_vma *vma);
int __must_check i915_vma_unbind(struct i915_vma *vma);
/*
* BEWARE: Do not use the function below unless you can _absolutely_
return (int32_t)(seq1 - seq2) >= 0;
}
+static inline bool i915_gem_request_started(struct drm_i915_gem_request *req,
+ bool lazy_coherency)
+{
+ u32 seqno = req->ring->get_seqno(req->ring, lazy_coherency);
+ return i915_seqno_passed(seqno, req->previous_seqno);
+}
+
static inline bool i915_gem_request_completed(struct drm_i915_gem_request *req,
bool lazy_coherency)
{
- u32 seqno;
-
- BUG_ON(req == NULL);
-
- seqno = req->ring->get_seqno(req->ring, lazy_coherency);
-
+ u32 seqno = req->ring->get_seqno(req->ring, lazy_coherency);
return i915_seqno_passed(seqno, req->seqno);
}
return test_bit(ring->id, &dev_priv->gpu_error.missed_irq_rings);
}
-static int __i915_spin_request(struct drm_i915_gem_request *req)
+static unsigned long local_clock_us(unsigned *cpu)
+{
+ unsigned long t;
+
+ /* Cheaply and approximately convert from nanoseconds to microseconds.
+ * The result and subsequent calculations are also defined in the same
+ * approximate microseconds units. The principal source of timing
+ * error here is from the simple truncation.
+ *
+ * Note that local_clock() is only defined wrt to the current CPU;
+ * the comparisons are no longer valid if we switch CPUs. Instead of
+ * blocking preemption for the entire busywait, we can detect the CPU
+ * switch and use that as indicator of system load and a reason to
+ * stop busywaiting, see busywait_stop().
+ */
+ *cpu = get_cpu();
+ t = local_clock() >> 10;
+ put_cpu();
+
+ return t;
+}
+
+static bool busywait_stop(unsigned long timeout, unsigned cpu)
+{
+ unsigned this_cpu;
+
+ if (time_after(local_clock_us(&this_cpu), timeout))
+ return true;
+
+ return this_cpu != cpu;
+}
+
+static int __i915_spin_request(struct drm_i915_gem_request *req, int state)
{
unsigned long timeout;
+ unsigned cpu;
+
+ /* When waiting for high frequency requests, e.g. during synchronous
+ * rendering split between the CPU and GPU, the finite amount of time
+ * required to set up the irq and wait upon it limits the response
+ * rate. By busywaiting on the request completion for a short while we
+ * can service the high frequency waits as quick as possible. However,
+ * if it is a slow request, we want to sleep as quickly as possible.
+ * The tradeoff between waiting and sleeping is roughly the time it
+ * takes to sleep on a request, on the order of a microsecond.
+ */
- if (i915_gem_request_get_ring(req)->irq_refcount)
+ if (req->ring->irq_refcount)
return -EBUSY;
- timeout = jiffies + 1;
+ /* Only spin if we know the GPU is processing this request */
+ if (!i915_gem_request_started(req, true))
+ return -EAGAIN;
+
+ timeout = local_clock_us(&cpu) + 5;
while (!need_resched()) {
if (i915_gem_request_completed(req, true))
return 0;
- if (time_after_eq(jiffies, timeout))
+ if (signal_pending_state(state, current))
+ break;
+
+ if (busywait_stop(timeout, cpu))
break;
cpu_relax_lowlatency();
}
+
if (i915_gem_request_completed(req, false))
return 0;
struct drm_i915_private *dev_priv = dev->dev_private;
const bool irq_test_in_progress =
ACCESS_ONCE(dev_priv->gpu_error.test_irq_rings) & intel_ring_flag(ring);
+ int state = interruptible ? TASK_INTERRUPTIBLE : TASK_UNINTERRUPTIBLE;
DEFINE_WAIT(wait);
unsigned long timeout_expire;
s64 before, now;
before = ktime_get_raw_ns();
/* Optimistic spin for the next jiffie before touching IRQs */
- ret = __i915_spin_request(req);
+ ret = __i915_spin_request(req, state);
if (ret == 0)
goto out;
for (;;) {
struct timer_list timer;
- prepare_to_wait(&ring->irq_queue, &wait,
- interruptible ? TASK_INTERRUPTIBLE : TASK_UNINTERRUPTIBLE);
+ prepare_to_wait(&ring->irq_queue, &wait, state);
/* We need to check whether any gpu reset happened in between
* the caller grabbing the seqno and now ... */
break;
}
- if (interruptible && signal_pending(current)) {
+ if (signal_pending_state(state, current)) {
ret = -ERESTARTSYS;
break;
}
request->batch_obj = obj;
request->emitted_jiffies = jiffies;
+ request->previous_seqno = ring->last_submitted_seqno;
ring->last_submitted_seqno = request->seqno;
list_add_tail(&request->list, &ring->request_list);
return false;
}
+void __i915_vma_set_map_and_fenceable(struct i915_vma *vma)
+{
+ struct drm_i915_gem_object *obj = vma->obj;
+ bool mappable, fenceable;
+ u32 fence_size, fence_alignment;
+
+ fence_size = i915_gem_get_gtt_size(obj->base.dev,
+ obj->base.size,
+ obj->tiling_mode);
+ fence_alignment = i915_gem_get_gtt_alignment(obj->base.dev,
+ obj->base.size,
+ obj->tiling_mode,
+ true);
+
+ fenceable = (vma->node.size == fence_size &&
+ (vma->node.start & (fence_alignment - 1)) == 0);
+
+ mappable = (vma->node.start + fence_size <=
+ to_i915(obj->base.dev)->gtt.mappable_end);
+
+ obj->map_and_fenceable = mappable && fenceable;
+}
+
static int
i915_gem_object_do_pin(struct drm_i915_gem_object *obj,
struct i915_address_space *vm,
if (ggtt_view && ggtt_view->type == I915_GGTT_VIEW_NORMAL &&
(bound ^ vma->bound) & GLOBAL_BIND) {
- bool mappable, fenceable;
- u32 fence_size, fence_alignment;
-
- fence_size = i915_gem_get_gtt_size(obj->base.dev,
- obj->base.size,
- obj->tiling_mode);
- fence_alignment = i915_gem_get_gtt_alignment(obj->base.dev,
- obj->base.size,
- obj->tiling_mode,
- true);
-
- fenceable = (vma->node.size == fence_size &&
- (vma->node.start & (fence_alignment - 1)) == 0);
-
- mappable = (vma->node.start + fence_size <=
- dev_priv->gtt.mappable_end);
-
- obj->map_and_fenceable = mappable && fenceable;
-
+ __i915_vma_set_map_and_fenceable(vma);
WARN_ON(flags & PIN_MAPPABLE && !obj->map_and_fenceable);
}
return ret;
}
vma->bound |= GLOBAL_BIND;
+ __i915_vma_set_map_and_fenceable(vma);
list_add_tail(&vma->mm_list, &ggtt_vm->inactive_list);
}
}
vma->bound |= GLOBAL_BIND;
+ __i915_vma_set_map_and_fenceable(vma);
list_add_tail(&vma->mm_list, &ggtt->inactive_list);
}
static void ironlake_pfit_disable(struct intel_crtc *crtc, bool force);
static void ironlake_pfit_enable(struct intel_crtc *crtc);
static void intel_modeset_setup_hw_state(struct drm_device *dev);
+static void intel_pre_disable_primary(struct drm_crtc *crtc);
typedef struct {
int min, max;
struct drm_i915_gem_object *obj;
struct drm_plane *primary = intel_crtc->base.primary;
struct drm_plane_state *plane_state = primary->state;
+ struct drm_crtc_state *crtc_state = intel_crtc->base.state;
+ struct intel_plane *intel_plane = to_intel_plane(primary);
struct drm_framebuffer *fb;
if (!plane_config->fb)
}
}
+ /*
+ * We've failed to reconstruct the BIOS FB. Current display state
+ * indicates that the primary plane is visible, but has a NULL FB,
+ * which will lead to problems later if we don't fix it up. The
+ * simplest solution is to just disable the primary plane now and
+ * pretend the BIOS never had it enabled.
+ */
+ to_intel_plane_state(plane_state)->visible = false;
+ crtc_state->plane_mask &= ~(1 << drm_plane_index(primary));
+ intel_pre_disable_primary(&intel_crtc->base);
+ intel_plane->disable_plane(primary, &intel_crtc->base);
+
return;
valid_fb:
return true;
}
-static void i845_update_cursor(struct drm_crtc *crtc, u32 base)
+static void i845_update_cursor(struct drm_crtc *crtc, u32 base, bool on)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
uint32_t cntl = 0, size = 0;
- if (base) {
+ if (on) {
unsigned int width = intel_crtc->base.cursor->state->crtc_w;
unsigned int height = intel_crtc->base.cursor->state->crtc_h;
unsigned int stride = roundup_pow_of_two(width) * 4;
}
}
-static void i9xx_update_cursor(struct drm_crtc *crtc, u32 base)
+static void i9xx_update_cursor(struct drm_crtc *crtc, u32 base, bool on)
{
struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
- uint32_t cntl;
+ uint32_t cntl = 0;
- cntl = 0;
- if (base) {
+ if (on) {
cntl = MCURSOR_GAMMA_ENABLE;
switch (intel_crtc->base.cursor->state->crtc_w) {
case 64:
int y = cursor_state->crtc_y;
u32 base = 0, pos = 0;
- if (on)
- base = intel_crtc->cursor_addr;
+ base = intel_crtc->cursor_addr;
if (x >= intel_crtc->config->pipe_src_w)
- base = 0;
+ on = false;
if (y >= intel_crtc->config->pipe_src_h)
- base = 0;
+ on = false;
if (x < 0) {
if (x + cursor_state->crtc_w <= 0)
- base = 0;
+ on = false;
pos |= CURSOR_POS_SIGN << CURSOR_X_SHIFT;
x = -x;
if (y < 0) {
if (y + cursor_state->crtc_h <= 0)
- base = 0;
+ on = false;
pos |= CURSOR_POS_SIGN << CURSOR_Y_SHIFT;
y = -y;
}
pos |= y << CURSOR_Y_SHIFT;
- if (base == 0 && intel_crtc->cursor_base == 0)
- return;
-
I915_WRITE(CURPOS(pipe), pos);
/* ILK+ do this automagically */
}
if (IS_845G(dev) || IS_I865G(dev))
- i845_update_cursor(crtc, base);
+ i845_update_cursor(crtc, base, on);
else
- i9xx_update_cursor(crtc, base);
+ i9xx_update_cursor(crtc, base, on);
}
static bool cursor_size_ok(struct drm_device *dev,
struct drm_crtc *crtc = crtc_state->base.crtc;
struct drm_framebuffer *fb = state->base.fb;
struct drm_i915_gem_object *obj = intel_fb_obj(fb);
+ enum pipe pipe = to_intel_plane(plane)->pipe;
unsigned stride;
int ret;
return -EINVAL;
}
+ /*
+ * There's something wrong with the cursor on CHV pipe C.
+ * If it straddles the left edge of the screen then
+ * moving it away from the edge or disabling it often
+ * results in a pipe underrun, and often that can lead to
+ * dead pipe (constant underrun reported, and it scans
+ * out just a solid color). To recover from that, the
+ * display power well must be turned off and on again.
+ * Refuse the put the cursor into that compromised position.
+ */
+ if (IS_CHERRYVIEW(plane->dev) && pipe == PIPE_C &&
+ state->visible && state->base.crtc_x < 0) {
+ DRM_DEBUG_KMS("CHV cursor C not allowed to straddle the left screen edge\n");
+ return -EINVAL;
+ }
+
return 0;
}
crtc = crtc ? crtc : plane->crtc;
intel_crtc = to_intel_crtc(crtc);
- if (intel_crtc->cursor_bo == obj)
- goto update;
-
if (!obj)
addr = 0;
else if (!INTEL_INFO(dev)->cursor_needs_physical)
addr = obj->phys_handle->busaddr;
intel_crtc->cursor_addr = addr;
- intel_crtc->cursor_bo = obj;
-update:
if (crtc->state->active)
intel_crtc_update_cursor(crtc, state->visible);
}
int adjusted_x;
int adjusted_y;
- struct drm_i915_gem_object *cursor_bo;
uint32_t cursor_addr;
uint32_t cursor_cntl;
uint32_t cursor_size;
struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
struct drm_i915_private *dev_priv = to_i915(connector->dev);
bool live_status = false;
- unsigned int retry = 3;
+ unsigned int try;
DRM_DEBUG_KMS("[CONNECTOR:%d:%s]\n",
connector->base.id, connector->name);
intel_display_power_get(dev_priv, POWER_DOMAIN_GMBUS);
- while (!live_status && --retry) {
+ for (try = 0; !live_status && try < 4; try++) {
+ if (try)
+ msleep(10);
live_status = intel_digital_port_connected(dev_priv,
hdmi_to_dig_port(intel_hdmi));
- mdelay(10);
}
if (!live_status)
fan->type = NVBIOS_THERM_FAN_UNK;
}
+ fan->fan_mode = NVBIOS_THERM_FAN_LINEAR;
fan->min_duty = nvbios_rd08(bios, data + 0x02);
fan->max_duty = nvbios_rd08(bios, data + 0x03);
config SENSORS_SHT15
tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
depends on GPIOLIB || COMPILE_TEST
+ select BITREVERSE
help
If you say yes here you get support for the Sensiron SHT10, SHT11,
SHT15, SHT71, SHT75 humidity and temperature sensors.
u16 config_orig;
unsigned long last_update;
int temp[3];
+ bool first_time;
};
/* convert left adjusted 13-bit TMP102 register value to milliCelsius */
tmp102->temp[i] = tmp102_reg_to_mC(status);
}
tmp102->last_update = jiffies;
+ tmp102->first_time = false;
}
mutex_unlock(&tmp102->lock);
return tmp102;
{
struct tmp102 *tmp102 = tmp102_update_device(dev);
+ /* Is it too early even to return a conversion? */
+ if (tmp102->first_time) {
+ dev_dbg(dev, "%s: Conversion not ready yet..\n", __func__);
+ return -EAGAIN;
+ }
+
*temp = tmp102->temp[0];
return 0;
struct sensor_device_attribute *sda = to_sensor_dev_attr(attr);
struct tmp102 *tmp102 = tmp102_update_device(dev);
+ /* Is it too early even to return a read? */
+ if (tmp102->first_time)
+ return -EAGAIN;
+
return sprintf(buf, "%d\n", tmp102->temp[sda->index]);
}
status = -ENODEV;
goto fail_restore_config;
}
- tmp102->last_update = jiffies - HZ;
+ tmp102->last_update = jiffies;
+ /* Mark that we are not ready with data until conversion is complete */
+ tmp102->first_time = true;
mutex_init(&tmp102->lock);
hwmon_dev = hwmon_device_register_with_groups(dev, client->name,
* d is always 6 on Keystone I2C controller
*/
- /* get minimum of 7 MHz clock, but max of 12 MHz */
- psc = (input_clock / 7000000) - 1;
+ /*
+ * Both Davinci and current Keystone User Guides recommend a value
+ * between 7MHz and 12MHz. In reality 7MHz module clock doesn't
+ * always produce enough margin between SDA and SCL transitions.
+ * Measurements show that the higher the module clock is, the
+ * bigger is the margin, providing more reliable communication.
+ * So we better target for 12MHz.
+ */
+ psc = (input_clock / 12000000) - 1;
if ((input_clock / (psc + 1)) > 12000000)
psc++; /* better to run under spec than over */
d = (psc >= 2) ? 5 : 7 - psc;
tx_aborted:
if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err)
complete(&dev->cmd_complete);
+ else if (unlikely(dev->accessor_flags & ACCESS_INTR_MASK)) {
+ /* workaround to trigger pending interrupt */
+ stat = dw_readl(dev, DW_IC_INTR_MASK);
+ i2c_dw_disable_int(dev);
+ dw_writel(dev, stat, DW_IC_INTR_MASK);
+ }
return IRQ_HANDLED;
}
#define ACCESS_SWAP 0x00000001
#define ACCESS_16BIT 0x00000002
+#define ACCESS_INTR_MASK 0x00000004
extern int i2c_dw_init(struct dw_i2c_dev *dev);
extern void i2c_dw_disable(struct dw_i2c_dev *dev);
static int dw_i2c_acpi_configure(struct platform_device *pdev)
{
struct dw_i2c_dev *dev = platform_get_drvdata(pdev);
+ const struct acpi_device_id *id;
dev->adapter.nr = -1;
dev->tx_fifo_depth = 32;
dw_i2c_acpi_params(pdev, "FMCN", &dev->fs_hcnt, &dev->fs_lcnt,
&dev->sda_hold_time);
+ id = acpi_match_device(pdev->dev.driver->acpi_match_table, &pdev->dev);
+ if (id && id->driver_data)
+ dev->accessor_flags |= (u32)id->driver_data;
+
return 0;
}
{ "INT3433", 0 },
{ "80860F41", 0 },
{ "808622C1", 0 },
- { "AMD0010", 0 },
+ { "AMD0010", ACCESS_INTR_MASK },
{ }
};
MODULE_DEVICE_TABLE(acpi, dw_i2c_acpi_match);
}
r = i2c_dw_probe(dev);
- if (r) {
+ if (r && !dev->pm_runtime_disabled)
pm_runtime_disable(&pdev->dev);
- return r;
- }
- return 0;
+ return r;
}
static int dw_i2c_plat_remove(struct platform_device *pdev)
pm_runtime_dont_use_autosuspend(&pdev->dev);
pm_runtime_put_sync(&pdev->dev);
- pm_runtime_disable(&pdev->dev);
+ if (!dev->pm_runtime_disabled)
+ pm_runtime_disable(&pdev->dev);
return 0;
}
i2c_imx, IMX_I2C_I2CR);
imx_i2c_write_reg(i2c_imx->hwdata->i2sr_clr_opcode, i2c_imx, IMX_I2C_I2SR);
+ i2c_imx_init_recovery_info(i2c_imx, pdev);
+
/* Add I2C adapter */
ret = i2c_add_numbered_adapter(&i2c_imx->adapter);
if (ret < 0) {
goto clk_disable;
}
- i2c_imx_init_recovery_info(i2c_imx, pdev);
-
/* Set up platform driver data */
platform_set_drvdata(pdev, i2c_imx);
clk_disable_unprepare(i2c_imx->clk);
bool errata_delay;
struct reset_control *rstc;
bool irq_clear_inverted;
+ /* Clk div is 2 to the power n, not 2 to the power n + 1 */
+ bool clk_n_base_0;
};
static struct mv64xxx_i2c_regs mv64xxx_i2c_regs_mv64xxx = {
#ifdef CONFIG_OF
#ifdef CONFIG_HAVE_CLK
static int
-mv64xxx_calc_freq(const int tclk, const int n, const int m)
+mv64xxx_calc_freq(struct mv64xxx_i2c_data *drv_data,
+ const int tclk, const int n, const int m)
{
- return tclk / (10 * (m + 1) * (2 << n));
+ if (drv_data->clk_n_base_0)
+ return tclk / (10 * (m + 1) * (1 << n));
+ else
+ return tclk / (10 * (m + 1) * (2 << n));
}
static bool
-mv64xxx_find_baud_factors(const u32 req_freq, const u32 tclk, u32 *best_n,
- u32 *best_m)
+mv64xxx_find_baud_factors(struct mv64xxx_i2c_data *drv_data,
+ const u32 req_freq, const u32 tclk)
{
int freq, delta, best_delta = INT_MAX;
int m, n;
for (n = 0; n <= 7; n++)
for (m = 0; m <= 15; m++) {
- freq = mv64xxx_calc_freq(tclk, n, m);
+ freq = mv64xxx_calc_freq(drv_data, tclk, n, m);
delta = req_freq - freq;
if (delta >= 0 && delta < best_delta) {
- *best_m = m;
- *best_n = n;
+ drv_data->freq_m = m;
+ drv_data->freq_n = n;
best_delta = delta;
}
if (best_delta == 0)
if (of_property_read_u32(np, "clock-frequency", &bus_freq))
bus_freq = 100000; /* 100kHz by default */
- if (!mv64xxx_find_baud_factors(bus_freq, tclk,
- &drv_data->freq_n, &drv_data->freq_m)) {
+ if (of_device_is_compatible(np, "allwinner,sun4i-a10-i2c") ||
+ of_device_is_compatible(np, "allwinner,sun6i-a31-i2c"))
+ drv_data->clk_n_base_0 = true;
+
+ if (!mv64xxx_find_baud_factors(drv_data, bus_freq, tclk)) {
rc = -EINVAL;
goto out;
}
if (slave->flags & I2C_CLIENT_TEN)
return -EAFNOSUPPORT;
- pm_runtime_forbid(rcar_i2c_priv_to_dev(priv));
+ pm_runtime_get_sync(rcar_i2c_priv_to_dev(priv));
priv->slave = slave;
rcar_i2c_write(priv, ICSAR, slave->addr);
priv->slave = NULL;
- pm_runtime_allow(rcar_i2c_priv_to_dev(priv));
+ pm_runtime_put(rcar_i2c_priv_to_dev(priv));
return 0;
}
&i2c->scl_fall_ns))
i2c->scl_fall_ns = 300;
if (of_property_read_u32(pdev->dev.of_node, "i2c-sda-falling-time-ns",
- &i2c->scl_fall_ns))
+ &i2c->sda_fall_ns))
i2c->sda_fall_ns = i2c->scl_fall_ns;
strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name));
adap = &i2c_dev->adap;
i2c_set_adapdata(adap, i2c_dev);
- snprintf(adap->name, sizeof(adap->name), "ST I2C(0x%pa)", &res->start);
+ snprintf(adap->name, sizeof(adap->name), "ST I2C(%pa)", &res->start);
adap->owner = THIS_MODULE;
adap->timeout = 2 * HZ;
adap->retries = 0;
return;
}
+ memset(&db9_parport_cb, 0, sizeof(db9_parport_cb));
db9_parport_cb.flags = PARPORT_FLAG_EXCL;
pd = parport_register_dev_model(pp, "db9", &db9_parport_cb, port_idx);
pads = gc_cfg[port_idx].args + 1;
n_pads = gc_cfg[port_idx].nargs - 1;
+ memset(&gc_parport_cb, 0, sizeof(gc_parport_cb));
gc_parport_cb.flags = PARPORT_FLAG_EXCL;
pd = parport_register_dev_model(pp, "gamecon", &gc_parport_cb,
n_buttons = tgfx_cfg[port_idx].args + 1;
n_devs = tgfx_cfg[port_idx].nargs - 1;
+ memset(&tgfx_parport_cb, 0, sizeof(tgfx_parport_cb));
tgfx_parport_cb.flags = PARPORT_FLAG_EXCL;
pd = parport_register_dev_model(pp, "turbografx", &tgfx_parport_cb,
w->parport = pp;
+ memset(&walkera0701_parport_cb, 0, sizeof(walkera0701_parport_cb));
walkera0701_parport_cb.flags = PARPORT_FLAG_EXCL;
walkera0701_parport_cb.irq_func = walkera0701_irq_handler;
walkera0701_parport_cb.private = w;
ret = regmap_update_bits(arizona->regmap,
ARIZONA_HAPTICS_CONTROL_1,
- ARIZONA_HAP_CTRL_MASK,
- 1 << ARIZONA_HAP_CTRL_SHIFT);
+ ARIZONA_HAP_CTRL_MASK, 0);
if (ret != 0) {
dev_err(arizona->dev, "Failed to stop haptics: %d\n",
ret);
#define DRIVER_NAME "elan_i2c"
#define ELAN_DRIVER_VERSION "1.6.1"
+#define ELAN_VENDOR_ID 0x04f3
#define ETP_MAX_PRESSURE 255
#define ETP_FWIDTH_REDUCE 90
#define ETP_FINGER_WIDTH 15
input->name = "Elan Touchpad";
input->id.bustype = BUS_I2C;
+ input->id.vendor = ELAN_VENDOR_ID;
+ input->id.product = data->product_id;
input_set_drvdata(input, data);
error = input_mt_init_slots(input, ETP_MAX_FINGERS,
{
struct pardev_cb parkbd_parport_cb;
+ memset(&parkbd_parport_cb, 0, sizeof(parkbd_parport_cb));
parkbd_parport_cb.irq_func = parkbd_interrupt;
parkbd_parport_cb.flags = PARPORT_FLAG_EXCL;
input_set_abs_params(inputdev, ABS_TILT_Y, AIPTEK_TILT_MIN, AIPTEK_TILT_MAX, 0, 0);
input_set_abs_params(inputdev, ABS_WHEEL, AIPTEK_WHEEL_MIN, AIPTEK_WHEEL_MAX - 1, 0, 0);
+ /* Verify that a device really has an endpoint */
+ if (intf->altsetting[0].desc.bNumEndpoints < 1) {
+ dev_err(&intf->dev,
+ "interface has %d endpoints, but must have minimum 1\n",
+ intf->altsetting[0].desc.bNumEndpoints);
+ err = -EINVAL;
+ goto fail3;
+ }
endpoint = &intf->altsetting[0].endpoint[0].desc;
/* Go set up our URB, which is called when the tablet receives
if (i == ARRAY_SIZE(speeds)) {
dev_info(&intf->dev,
"Aiptek tried all speeds, no sane response\n");
+ err = -EINVAL;
goto fail3;
}
{ }
};
+static unsigned int chromebook_tp_buttons[] = {
+ KEY_RESERVED,
+ KEY_RESERVED,
+ KEY_RESERVED,
+ KEY_RESERVED,
+ KEY_RESERVED,
+ BTN_LEFT
+};
+
+static struct mxt_acpi_platform_data chromebook_platform_data[] = {
+ {
+ /* Touchpad */
+ .hid = "ATML0000",
+ .pdata = {
+ .t19_num_keys = ARRAY_SIZE(chromebook_tp_buttons),
+ .t19_keymap = chromebook_tp_buttons,
+ },
+ },
+ {
+ /* Touchscreen */
+ .hid = "ATML0001",
+ },
+ { }
+};
+
static const struct dmi_system_id mxt_dmi_table[] = {
{
/* 2015 Google Pixel */
},
.driver_data = samus_platform_data,
},
+ {
+ /* Other Google Chromebooks */
+ .ident = "Chromebook",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "GOOGLE"),
+ },
+ .driver_data = chromebook_platform_data,
+ },
{ }
};
{ "qt602240_ts", 0 },
{ "atmel_mxt_ts", 0 },
{ "atmel_mxt_tp", 0 },
+ { "maxtouch", 0 },
{ "mXT224", 0 },
{ }
};
disable_irq(client->irq);
- if (device_may_wakeup(dev) || ts->keep_power_in_suspend) {
+ if (device_may_wakeup(dev)) {
+ /*
+ * The device will automatically enter idle mode
+ * that has reduced power consumption.
+ */
+ ts->wake_irq_enabled = (enable_irq_wake(client->irq) == 0);
+ } else if (ts->keep_power_in_suspend) {
for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
error = elants_i2c_send(client, set_sleep_cmd,
sizeof(set_sleep_cmd));
dev_err(&client->dev,
"suspend command failed: %d\n", error);
}
-
- if (device_may_wakeup(dev))
- ts->wake_irq_enabled =
- (enable_irq_wake(client->irq) == 0);
} else {
elants_i2c_power_off(ts);
}
int retry_cnt;
int error;
- if (device_may_wakeup(dev) && ts->wake_irq_enabled)
- disable_irq_wake(client->irq);
-
- if (ts->keep_power_in_suspend) {
+ if (device_may_wakeup(dev)) {
+ if (ts->wake_irq_enabled)
+ disable_irq_wake(client->irq);
+ elants_i2c_sw_reset(client);
+ } else if (ts->keep_power_in_suspend) {
for (retry_cnt = 0; retry_cnt < MAX_RETRIES; retry_cnt++) {
error = elants_i2c_send(client, set_active_cmd,
sizeof(set_active_cmd));
}
}
+static bool access_error(struct vm_area_struct *vma, struct fault *fault)
+{
+ unsigned long requested = 0;
+
+ if (fault->flags & PPR_FAULT_EXEC)
+ requested |= VM_EXEC;
+
+ if (fault->flags & PPR_FAULT_READ)
+ requested |= VM_READ;
+
+ if (fault->flags & PPR_FAULT_WRITE)
+ requested |= VM_WRITE;
+
+ return (requested & ~vma->vm_flags) != 0;
+}
+
static void do_fault(struct work_struct *work)
{
struct fault *fault = container_of(work, struct fault, work);
goto out;
}
- if (!(vma->vm_flags & (VM_READ | VM_EXEC | VM_WRITE))) {
- /* handle_mm_fault would BUG_ON() */
+ /* Check if we have the right permissions on the vma */
+ if (access_error(vma, fault)) {
up_read(&mm->mmap_sem);
handle_fault_error(fault);
goto out;
};
#define PRQ_RING_MASK ((0x1000 << PRQ_ORDER) - 0x10)
+
+static bool access_error(struct vm_area_struct *vma, struct page_req_dsc *req)
+{
+ unsigned long requested = 0;
+
+ if (req->exe_req)
+ requested |= VM_EXEC;
+
+ if (req->rd_req)
+ requested |= VM_READ;
+
+ if (req->wr_req)
+ requested |= VM_WRITE;
+
+ return (requested & ~vma->vm_flags) != 0;
+}
+
static irqreturn_t prq_event_thread(int irq, void *d)
{
struct intel_iommu *iommu = d;
if (!vma || address < vma->vm_start)
goto invalid;
+ if (access_error(vma, req))
+ goto invalid;
+
ret = handle_mm_fault(svm->mm, vma, address,
req->wr_req ? FAULT_FLAG_WRITE : 0);
if (ret & VM_FAULT_ERROR)
*/
void mddev_suspend(struct mddev *mddev)
{
- BUG_ON(mddev->suspended);
- mddev->suspended = 1;
+ if (mddev->suspended++)
+ return;
synchronize_rcu();
wait_event(mddev->sb_wait, atomic_read(&mddev->active_io) == 0);
mddev->pers->quiesce(mddev, 1);
void mddev_resume(struct mddev *mddev)
{
- mddev->suspended = 0;
+ if (--mddev->suspended)
+ return;
wake_up(&mddev->sb_wait);
mddev->pers->quiesce(mddev, 0);
rdev->journal_tail = le64_to_cpu(sb->journal_tail);
if (mddev->recovery_cp == MaxSector)
set_bit(MD_JOURNAL_CLEAN, &mddev->flags);
- rdev->raid_disk = mddev->raid_disks;
+ rdev->raid_disk = 0;
break;
default:
rdev->saved_raid_disk = role;
/* Activating a spare .. or possibly reactivating
* if we ever get bitmaps working here.
*/
+ int err;
if (rdev->raid_disk != -1)
return -EBUSY;
rdev->saved_raid_disk = -1;
clear_bit(In_sync, &rdev->flags);
clear_bit(Bitmap_sync, &rdev->flags);
- remove_and_add_spares(rdev->mddev, rdev);
- if (rdev->raid_disk == -1)
- return -EBUSY;
+ err = rdev->mddev->pers->
+ hot_add_disk(rdev->mddev, rdev);
+ if (err) {
+ rdev->raid_disk = -1;
+ return err;
+ } else
+ sysfs_notify_dirent_safe(rdev->sysfs_state);
+ if (sysfs_link_rdev(rdev->mddev, rdev))
+ /* failure here is OK */;
/* don't wakeup anyone, leave that to userspace. */
} else {
if (slot >= rdev->mddev->raid_disks &&
}
mddev_unlock(mddev);
}
- } else if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery) ||
- test_bit(MD_RECOVERY_NEEDED, &mddev->recovery))
+ } else if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery))
return -EBUSY;
else if (cmd_match(page, "resync"))
clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
return -EINVAL;
err = mddev_lock(mddev);
if (!err) {
- clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
- err = mddev->pers->start_reshape(mddev);
+ if (test_bit(MD_RECOVERY_RUNNING, &mddev->recovery))
+ err = -EBUSY;
+ else {
+ clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
+ err = mddev->pers->start_reshape(mddev);
+ }
mddev_unlock(mddev);
}
if (err)
static inline int sysfs_link_rdev(struct mddev *mddev, struct md_rdev *rdev)
{
char nm[20];
- if (!test_bit(Replacement, &rdev->flags) && mddev->kobj.sd) {
+ if (!test_bit(Replacement, &rdev->flags) &&
+ !test_bit(Journal, &rdev->flags) &&
+ mddev->kobj.sd) {
sprintf(nm, "rd%d", rdev->raid_disk);
return sysfs_create_link(&mddev->kobj, &rdev->kobj, nm);
} else
static inline void sysfs_unlink_rdev(struct mddev *mddev, struct md_rdev *rdev)
{
char nm[20];
- if (!test_bit(Replacement, &rdev->flags) && mddev->kobj.sd) {
+ if (!test_bit(Replacement, &rdev->flags) &&
+ !test_bit(Journal, &rdev->flags) &&
+ mddev->kobj.sd) {
sprintf(nm, "rd%d", rdev->raid_disk);
sysfs_remove_link(&mddev->kobj, nm);
}
first = i;
fbio = r10_bio->devs[i].bio;
+ fbio->bi_iter.bi_size = r10_bio->sectors << 9;
+ fbio->bi_iter.bi_idx = 0;
vcnt = (r10_bio->sectors + (PAGE_SIZE >> 9) - 1) >> (PAGE_SHIFT - 9);
/* now find blocks with errors */
bio_reset(tbio);
tbio->bi_vcnt = vcnt;
- tbio->bi_iter.bi_size = r10_bio->sectors << 9;
+ tbio->bi_iter.bi_size = fbio->bi_iter.bi_size;
tbio->bi_rw = WRITE;
tbio->bi_private = r10_bio;
tbio->bi_iter.bi_sector = r10_bio->devs[i].addr;
{
int i;
- for (i = 0; i < IVTV_CARD_MAX_VIDEO_INPUTS - 1; i++)
+ for (i = 0; i < IVTV_CARD_MAX_VIDEO_INPUTS; i++)
if (itv->card->video_inputs[i].video_type == 0)
break;
itv->nof_inputs = i;
- for (i = 0; i < IVTV_CARD_MAX_AUDIO_INPUTS - 1; i++)
+ for (i = 0; i < IVTV_CARD_MAX_AUDIO_INPUTS; i++)
if (itv->card->audio_inputs[i].audio_type == 0)
break;
itv->nof_audio_inputs = i;
int urbs_submitted;
/* USB control message buffer */
- #define BUF_SIZE 24
+ #define BUF_SIZE 128
u8 buf[BUF_SIZE];
/* Current configuration */
#include <media/videobuf2-v4l2.h>
#include <media/videobuf2-vmalloc.h>
+/*
+ * Used Avago MGA-81563 RF amplifier could be destroyed pretty easily with too
+ * strong signal or transmitting to bad antenna.
+ * Set RF gain control to 'grabbed' state by default for sure.
+ */
+static bool hackrf_enable_rf_gain_ctrl;
+module_param_named(enable_rf_gain_ctrl, hackrf_enable_rf_gain_ctrl, bool, 0644);
+MODULE_PARM_DESC(enable_rf_gain_ctrl, "enable RX/TX RF amplifier control (warn: could damage amplifier)");
+
/* HackRF USB API commands (from HackRF Library) */
enum {
CMD_SET_TRANSCEIVER_MODE = 0x01,
dev_err(dev->dev, "Could not initialize controls\n");
goto err_v4l2_ctrl_handler_free_rx;
}
+ v4l2_ctrl_grab(dev->rx_rf_gain, !hackrf_enable_rf_gain_ctrl);
v4l2_ctrl_handler_setup(&dev->rx_ctrl_handler);
/* Register controls for transmitter */
dev_err(dev->dev, "Could not initialize controls\n");
goto err_v4l2_ctrl_handler_free_tx;
}
+ v4l2_ctrl_grab(dev->tx_rf_gain, !hackrf_enable_rf_gain_ctrl);
v4l2_ctrl_handler_setup(&dev->tx_ctrl_handler);
/* Register the v4l2_device structure */
err_kfree:
kfree(dev);
err:
- dev_dbg(dev->dev, "failed=%d\n", ret);
+ dev_dbg(&intf->dev, "failed=%d\n", ret);
return ret;
}
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/compiler.h>
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/types.h>
#include <linux/slab.h>
ofpart_node = of_get_child_by_name(mtd_node, "partitions");
if (!ofpart_node) {
- pr_warn("%s: 'partitions' subnode not found on %s. Trying to parse direct subnodes as partitions.\n",
- master->name, mtd_node->full_name);
+ /*
+ * We might get here even when ofpart isn't used at all (e.g.,
+ * when using another parser), so don't be louder than
+ * KERN_DEBUG
+ */
+ pr_debug("%s: 'partitions' subnode not found on %s. Trying to parse direct subnodes as partitions.\n",
+ master->name, mtd_node->full_name);
ofpart_node = mtd_node;
dedicated = false;
+ } else if (!of_device_is_compatible(ofpart_node, "fixed-partitions")) {
+ /* The 'partitions' subnode might be used by another parser */
+ return 0;
}
/* First count the subnodes */
dfs_rootdir = debugfs_create_dir("ubi", NULL);
if (IS_ERR_OR_NULL(dfs_rootdir)) {
- int err = dfs_rootdir ? -ENODEV : PTR_ERR(dfs_rootdir);
+ int err = dfs_rootdir ? PTR_ERR(dfs_rootdir) : -ENODEV;
pr_err("UBI error: cannot create \"ubi\" debugfs directory, error %d\n",
err);
if (err && err != UBI_IO_BITFLIPS && !mtd_is_eccerr(err))
goto exit;
- crc = crc32(UBI_CRC32_INIT, vid_hdr, UBI_EC_HDR_SIZE_CRC);
+ crc = crc32(UBI_CRC32_INIT, vid_hdr, UBI_VID_HDR_SIZE_CRC);
hdr_crc = be32_to_cpu(vid_hdr->hdr_crc);
if (hdr_crc != crc) {
ubi_err(ubi, "bad VID header CRC at PEB %d, calculated %#08x, read %#08x",
return 0;
}
+static int __erase_worker(struct ubi_device *ubi, struct ubi_work *wl_wrk);
/**
* do_sync_erase - run the erase worker synchronously.
* @ubi: UBI device description object
static int do_sync_erase(struct ubi_device *ubi, struct ubi_wl_entry *e,
int vol_id, int lnum, int torture)
{
- struct ubi_work *wl_wrk;
+ struct ubi_work wl_wrk;
dbg_wl("sync erase of PEB %i", e->pnum);
- wl_wrk = kmalloc(sizeof(struct ubi_work), GFP_NOFS);
- if (!wl_wrk)
- return -ENOMEM;
-
- wl_wrk->e = e;
- wl_wrk->vol_id = vol_id;
- wl_wrk->lnum = lnum;
- wl_wrk->torture = torture;
+ wl_wrk.e = e;
+ wl_wrk.vol_id = vol_id;
+ wl_wrk.lnum = lnum;
+ wl_wrk.torture = torture;
- return erase_worker(ubi, wl_wrk, 0);
+ return __erase_worker(ubi, &wl_wrk);
}
/**
}
/**
- * erase_worker - physical eraseblock erase worker function.
+ * __erase_worker - physical eraseblock erase worker function.
* @ubi: UBI device description object
* @wl_wrk: the work object
* @shutdown: non-zero if the worker has to free memory and exit
* needed. Returns zero in case of success and a negative error code in case of
* failure.
*/
-static int erase_worker(struct ubi_device *ubi, struct ubi_work *wl_wrk,
- int shutdown)
+static int __erase_worker(struct ubi_device *ubi, struct ubi_work *wl_wrk)
{
struct ubi_wl_entry *e = wl_wrk->e;
int pnum = e->pnum;
int lnum = wl_wrk->lnum;
int err, available_consumed = 0;
- if (shutdown) {
- dbg_wl("cancel erasure of PEB %d EC %d", pnum, e->ec);
- kfree(wl_wrk);
- wl_entry_destroy(ubi, e);
- return 0;
- }
-
dbg_wl("erase PEB %d EC %d LEB %d:%d",
pnum, e->ec, wl_wrk->vol_id, wl_wrk->lnum);
err = sync_erase(ubi, e, wl_wrk->torture);
if (!err) {
- /* Fine, we've erased it successfully */
- kfree(wl_wrk);
-
spin_lock(&ubi->wl_lock);
wl_tree_add(e, &ubi->free);
ubi->free_count++;
}
ubi_err(ubi, "failed to erase PEB %d, error %d", pnum, err);
- kfree(wl_wrk);
if (err == -EINTR || err == -ENOMEM || err == -EAGAIN ||
err == -EBUSY) {
/* Re-schedule the LEB for erasure */
err1 = schedule_erase(ubi, e, vol_id, lnum, 0);
if (err1) {
+ wl_entry_destroy(ubi, e);
err = err1;
goto out_ro;
}
return err;
}
+static int erase_worker(struct ubi_device *ubi, struct ubi_work *wl_wrk,
+ int shutdown)
+{
+ int ret;
+
+ if (shutdown) {
+ struct ubi_wl_entry *e = wl_wrk->e;
+
+ dbg_wl("cancel erasure of PEB %d EC %d", e->pnum, e->ec);
+ kfree(wl_wrk);
+ wl_entry_destroy(ubi, e);
+ return 0;
+ }
+
+ ret = __erase_worker(ubi, wl_wrk);
+ kfree(wl_wrk);
+ return ret;
+}
+
/**
* ubi_wl_put_peb - return a PEB to the wear-leveling sub-system.
* @ubi: UBI device description object
struct netrx_pending_operations *npo)
{
struct xenvif_rx_meta *meta;
- struct xen_netif_rx_request *req;
+ struct xen_netif_rx_request req;
- req = RING_GET_REQUEST(&queue->rx, queue->rx.req_cons++);
+ RING_COPY_REQUEST(&queue->rx, queue->rx.req_cons++, &req);
meta = npo->meta + npo->meta_prod++;
meta->gso_type = XEN_NETIF_GSO_TYPE_NONE;
meta->gso_size = 0;
meta->size = 0;
- meta->id = req->id;
+ meta->id = req.id;
npo->copy_off = 0;
- npo->copy_gref = req->gref;
+ npo->copy_gref = req.gref;
return meta;
}
struct xenvif *vif = netdev_priv(skb->dev);
int nr_frags = skb_shinfo(skb)->nr_frags;
int i;
- struct xen_netif_rx_request *req;
+ struct xen_netif_rx_request req;
struct xenvif_rx_meta *meta;
unsigned char *data;
int head = 1;
/* Set up a GSO prefix descriptor, if necessary */
if ((1 << gso_type) & vif->gso_prefix_mask) {
- req = RING_GET_REQUEST(&queue->rx, queue->rx.req_cons++);
+ RING_COPY_REQUEST(&queue->rx, queue->rx.req_cons++, &req);
meta = npo->meta + npo->meta_prod++;
meta->gso_type = gso_type;
meta->gso_size = skb_shinfo(skb)->gso_size;
meta->size = 0;
- meta->id = req->id;
+ meta->id = req.id;
}
- req = RING_GET_REQUEST(&queue->rx, queue->rx.req_cons++);
+ RING_COPY_REQUEST(&queue->rx, queue->rx.req_cons++, &req);
meta = npo->meta + npo->meta_prod++;
if ((1 << gso_type) & vif->gso_mask) {
}
meta->size = 0;
- meta->id = req->id;
+ meta->id = req.id;
npo->copy_off = 0;
- npo->copy_gref = req->gref;
+ npo->copy_gref = req.gref;
data = skb->data;
while (data < skb_tail_pointer(skb)) {
* Allow a burst big enough to transmit a jumbo packet of up to 128kB.
* Otherwise the interface can seize up due to insufficient credit.
*/
- max_burst = RING_GET_REQUEST(&queue->tx, queue->tx.req_cons)->size;
- max_burst = min(max_burst, 131072UL);
- max_burst = max(max_burst, queue->credit_bytes);
+ max_burst = max(131072UL, queue->credit_bytes);
/* Take care that adding a new chunk of credit doesn't wrap to zero. */
max_credit = queue->remaining_credit + queue->credit_bytes;
spin_unlock_irqrestore(&queue->response_lock, flags);
if (cons == end)
break;
- txp = RING_GET_REQUEST(&queue->tx, cons++);
+ RING_COPY_REQUEST(&queue->tx, cons++, txp);
} while (1);
queue->tx.req_cons = cons;
}
if (drop_err)
txp = &dropped_tx;
- memcpy(txp, RING_GET_REQUEST(&queue->tx, cons + slots),
- sizeof(*txp));
+ RING_COPY_REQUEST(&queue->tx, cons + slots, txp);
/* If the guest submitted a frame >= 64 KiB then
* first->size overflowed and following slots will
return -EBADR;
}
- memcpy(&extra, RING_GET_REQUEST(&queue->tx, cons),
- sizeof(extra));
+ RING_COPY_REQUEST(&queue->tx, cons, &extra);
if (unlikely(!extra.type ||
extra.type >= XEN_NETIF_EXTRA_TYPE_MAX)) {
queue->tx.req_cons = ++cons;
idx = queue->tx.req_cons;
rmb(); /* Ensure that we see the request before we copy it. */
- memcpy(&txreq, RING_GET_REQUEST(&queue->tx, idx), sizeof(txreq));
+ RING_COPY_REQUEST(&queue->tx, idx, &txreq);
/* Credit-based scheduling. */
if (txreq.size > queue->remaining_credit &&
{
bool kill = nvme_io_incapable(ns->dev) && !blk_queue_dying(ns->queue);
- if (kill)
+ if (kill) {
blk_set_queue_dying(ns->queue);
+
+ /*
+ * The controller was shutdown first if we got here through
+ * device removal. The shutdown may requeue outstanding
+ * requests. These need to be aborted immediately so
+ * del_gendisk doesn't block indefinitely for their completion.
+ */
+ blk_mq_abort_requeue_list(ns->queue);
+ }
if (ns->disk->flags & GENHD_FL_UP)
del_gendisk(ns->disk);
if (kill || !blk_queue_dying(ns->queue)) {
{
struct nvme_ns *ns, *next;
+ if (nvme_io_incapable(dev)) {
+ /*
+ * If the device is not capable of IO (surprise hot-removal,
+ * for example), we need to quiesce prior to deleting the
+ * namespaces. This will end outstanding requests and prevent
+ * attempts to sync dirty data.
+ */
+ nvme_dev_shutdown(dev);
+ }
list_for_each_entry_safe(ns, next, &dev->namespaces, list)
nvme_ns_remove(ns);
}
tristate "Allwinner sun9i SoC USB PHY driver"
depends on ARCH_SUNXI && HAS_IOMEM && OF
depends on RESET_CONTROLLER
+ depends on USB_COMMON
select GENERIC_PHY
help
Enable this to support the transceiver that is part of Allwinner
struct phy_provider *provider;
struct resource *res;
unsigned cnt = 0;
+ int ret;
if (of_get_child_count(node) == 0) {
dev_err(dev, "PHY no child node\n");
if (of_property_read_u32(child, "reg", &id)) {
dev_err(dev, "missing reg property for %s\n",
child->name);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
if (id >= MAX_NUM_PHYS) {
dev_err(dev, "invalid PHY id: %u\n", id);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
if (core->phys[id].phy) {
dev_err(dev, "duplicated PHY id: %u\n", id);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
p = &core->phys[id];
p->phy = devm_phy_create(dev, child, &cygnus_pcie_phy_ops);
if (IS_ERR(p->phy)) {
dev_err(dev, "failed to create PHY\n");
- return PTR_ERR(p->phy);
+ ret = PTR_ERR(p->phy);
+ goto put_child;
}
p->core = core;
dev_dbg(dev, "registered %u PCIe PHY(s)\n", cnt);
return 0;
+put_child:
+ of_node_put(child);
+ return ret;
}
static const struct of_device_id cygnus_pcie_phy_match_table[] = {
struct phy_provider *phy_provider;
struct phy_berlin_priv *priv;
struct resource *res;
- int i = 0;
+ int ret, i = 0;
u32 phy_id;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (of_property_read_u32(child, "reg", &phy_id)) {
dev_err(dev, "missing reg property in node %s\n",
child->name);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
if (phy_id >= ARRAY_SIZE(phy_berlin_power_down_bits)) {
dev_err(dev, "invalid reg in node %s\n", child->name);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
phy_desc = devm_kzalloc(dev, sizeof(*phy_desc), GFP_KERNEL);
- if (!phy_desc)
- return -ENOMEM;
+ if (!phy_desc) {
+ ret = -ENOMEM;
+ goto put_child;
+ }
phy = devm_phy_create(dev, NULL, &phy_berlin_sata_ops);
if (IS_ERR(phy)) {
dev_err(dev, "failed to create PHY %d\n", phy_id);
- return PTR_ERR(phy);
+ ret = PTR_ERR(phy);
+ goto put_child;
}
phy_desc->phy = phy;
phy_provider =
devm_of_phy_provider_register(dev, phy_berlin_sata_phy_xlate);
return PTR_ERR_OR_ZERO(phy_provider);
+put_child:
+ of_node_put(child);
+ return ret;
}
static const struct of_device_id phy_berlin_sata_of_match[] = {
struct brcm_sata_phy *priv;
struct resource *res;
struct phy_provider *provider;
- int count = 0;
+ int ret, count = 0;
if (of_get_child_count(dn) == 0)
return -ENODEV;
if (of_property_read_u32(child, "reg", &id)) {
dev_err(dev, "missing reg property in node %s\n",
child->name);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
if (id >= MAX_PORTS) {
dev_err(dev, "invalid reg: %u\n", id);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
if (priv->phys[id].phy) {
dev_err(dev, "already registered port %u\n", id);
- return -EINVAL;
+ ret = -EINVAL;
+ goto put_child;
}
port = &priv->phys[id];
port->ssc_en = of_property_read_bool(child, "brcm,enable-ssc");
if (IS_ERR(port->phy)) {
dev_err(dev, "failed to create PHY\n");
- return PTR_ERR(port->phy);
+ ret = PTR_ERR(port->phy);
+ goto put_child;
}
phy_set_drvdata(port->phy, port);
dev_info(dev, "registered %d port(s)\n", count);
return 0;
+put_child:
+ of_node_put(child);
+ return ret;
}
static struct platform_driver brcm_sata_phy_driver = {
* @np: node containing the phy
* @index: index of the phy
*
- * Gets the phy using _of_phy_get(), and associates a device with it using
- * devres. On driver detach, release function is invoked on the devres data,
+ * Gets the phy using _of_phy_get(), then gets a refcount to it,
+ * and associates a device with it using devres. On driver detach,
+ * release function is invoked on the devres data,
* then, devres data is freed.
*
*/
return ERR_PTR(-ENOMEM);
phy = _of_phy_get(np, index);
- if (!IS_ERR(phy)) {
- *ptr = phy;
- devres_add(dev, ptr);
- } else {
+ if (IS_ERR(phy)) {
devres_free(ptr);
+ return phy;
}
+ if (!try_module_get(phy->ops->owner)) {
+ devres_free(ptr);
+ return ERR_PTR(-EPROBE_DEFER);
+ }
+
+ get_device(&phy->dev);
+
+ *ptr = phy;
+ devres_add(dev, ptr);
+
return phy;
}
EXPORT_SYMBOL_GPL(devm_of_phy_get_by_index);
miphy_phy = devm_kzalloc(&pdev->dev, sizeof(*miphy_phy),
GFP_KERNEL);
- if (!miphy_phy)
- return -ENOMEM;
+ if (!miphy_phy) {
+ ret = -ENOMEM;
+ goto put_child;
+ }
miphy_dev->phys[port] = miphy_phy;
phy = devm_phy_create(&pdev->dev, child, &miphy28lp_ops);
if (IS_ERR(phy)) {
dev_err(&pdev->dev, "failed to create PHY\n");
- return PTR_ERR(phy);
+ ret = PTR_ERR(phy);
+ goto put_child;
}
miphy_dev->phys[port]->phy = phy;
ret = miphy28lp_of_probe(child, miphy_phy);
if (ret)
- return ret;
+ goto put_child;
ret = miphy28lp_probe_resets(child, miphy_dev->phys[port]);
if (ret)
- return ret;
+ goto put_child;
phy_set_drvdata(phy, miphy_dev->phys[port]);
port++;
provider = devm_of_phy_provider_register(&pdev->dev, miphy28lp_xlate);
return PTR_ERR_OR_ZERO(provider);
+put_child:
+ of_node_put(child);
+ return ret;
}
static const struct of_device_id miphy28lp_of_match[] = {
miphy_phy = devm_kzalloc(&pdev->dev, sizeof(*miphy_phy),
GFP_KERNEL);
- if (!miphy_phy)
- return -ENOMEM;
+ if (!miphy_phy) {
+ ret = -ENOMEM;
+ goto put_child;
+ }
miphy_dev->phys[port] = miphy_phy;
phy = devm_phy_create(&pdev->dev, child, &miphy365x_ops);
if (IS_ERR(phy)) {
dev_err(&pdev->dev, "failed to create PHY\n");
- return PTR_ERR(phy);
+ ret = PTR_ERR(phy);
+ goto put_child;
}
miphy_dev->phys[port]->phy = phy;
ret = miphy365x_of_probe(child, miphy_phy);
if (ret)
- return ret;
+ goto put_child;
phy_set_drvdata(phy, miphy_dev->phys[port]);
&miphy_phy->ctrlreg);
if (ret) {
dev_err(&pdev->dev, "No sysconfig offset found\n");
- return ret;
+ goto put_child;
}
}
provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate);
return PTR_ERR_OR_ZERO(provider);
+put_child:
+ of_node_put(child);
+ return ret;
}
static const struct of_device_id miphy365x_of_match[] = {
struct resource *sif_res;
struct mt65xx_u3phy *u3phy;
struct resource res;
- int port;
+ int port, retval;
u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
if (!u3phy)
for_each_child_of_node(np, child_np) {
struct mt65xx_phy_instance *instance;
struct phy *phy;
- int retval;
instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
- if (!instance)
- return -ENOMEM;
+ if (!instance) {
+ retval = -ENOMEM;
+ goto put_child;
+ }
u3phy->phys[port] = instance;
phy = devm_phy_create(dev, child_np, &mt65xx_u3phy_ops);
if (IS_ERR(phy)) {
dev_err(dev, "failed to create phy\n");
- return PTR_ERR(phy);
+ retval = PTR_ERR(phy);
+ goto put_child;
}
retval = of_address_to_resource(child_np, 0, &res);
if (retval) {
dev_err(dev, "failed to get address resource(id-%d)\n",
port);
- return retval;
+ goto put_child;
}
instance->port_base = devm_ioremap_resource(&phy->dev, &res);
if (IS_ERR(instance->port_base)) {
dev_err(dev, "failed to remap phy regs\n");
- return PTR_ERR(instance->port_base);
+ retval = PTR_ERR(instance->port_base);
+ goto put_child;
}
instance->phy = phy;
provider = devm_of_phy_provider_register(dev, mt65xx_phy_xlate);
return PTR_ERR_OR_ZERO(provider);
+put_child:
+ of_node_put(child_np);
+ return retval;
}
static const struct of_device_id mt65xx_u3phy_id_table[] = {
for_each_available_child_of_node(dev->of_node, child) {
rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
- if (!rk_phy)
- return -ENOMEM;
+ if (!rk_phy) {
+ err = -ENOMEM;
+ goto put_child;
+ }
if (of_property_read_u32(child, "reg", ®_offset)) {
dev_err(dev, "missing reg property in node %s\n",
child->name);
- return -EINVAL;
+ err = -EINVAL;
+ goto put_child;
}
rk_phy->reg_offset = reg_offset;
rk_phy->phy = devm_phy_create(dev, child, &ops);
if (IS_ERR(rk_phy->phy)) {
dev_err(dev, "failed to create PHY\n");
- return PTR_ERR(rk_phy->phy);
+ err = PTR_ERR(rk_phy->phy);
+ goto put_child;
}
phy_set_drvdata(rk_phy->phy, rk_phy);
/* only power up usb phy when it use, so disable it when init*/
err = rockchip_usb_phy_power(rk_phy, 1);
if (err)
- return err;
+ goto put_child;
}
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
return PTR_ERR_OR_ZERO(phy_provider);
+put_child:
+ of_node_put(child);
+ return err;
}
static const struct of_device_id rockchip_usb_phy_dt_ids[] = {
return bcm2835_gpio_get_bit(pc, GPLEV0, offset);
}
-static int bcm2835_gpio_direction_output(struct gpio_chip *chip,
- unsigned offset, int value)
-{
- return pinctrl_gpio_direction_output(chip->base + offset);
-}
-
static void bcm2835_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
{
struct bcm2835_pinctrl *pc = dev_get_drvdata(chip->dev);
bcm2835_gpio_set_bit(pc, value ? GPSET0 : GPCLR0, offset);
}
+static int bcm2835_gpio_direction_output(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ bcm2835_gpio_set(chip, offset, value);
+ return pinctrl_gpio_direction_output(chip->base + offset);
+}
+
static int bcm2835_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
{
struct bcm2835_pinctrl *pc = dev_get_drvdata(chip->dev);
static struct imx_pinctrl_soc_info vf610_pinctrl_info = {
.pins = vf610_pinctrl_pads,
.npins = ARRAY_SIZE(vf610_pinctrl_pads),
- .flags = SHARE_MUX_CONF_REG,
+ .flags = SHARE_MUX_CONF_REG | ZERO_OFFSET_VALID,
};
static const struct of_device_id vf610_pinctrl_of_match[] = {
.padcfglock_offset = BXT_PADCFGLOCK, \
.hostown_offset = BXT_HOSTSW_OWN, \
.ie_offset = BXT_GPI_IE, \
+ .gpp_size = 32, \
.pin_base = (s), \
.npins = ((e) - (s) + 1), \
}
#include "pinctrl-intel.h"
-/* Maximum number of pads in each group */
-#define NPADS_IN_GPP 24
-
/* Offset from regs */
#define PADBAR 0x00c
#define GPI_IS 0x100
#define PADOWN_BITS 4
#define PADOWN_SHIFT(p) ((p) % 8 * PADOWN_BITS)
#define PADOWN_MASK(p) (0xf << PADOWN_SHIFT(p))
+#define PADOWN_GPP(p) ((p) / 8)
/* Offset from pad_regs */
#define PADCFG0 0x000
static bool intel_pad_owned_by_host(struct intel_pinctrl *pctrl, unsigned pin)
{
const struct intel_community *community;
- unsigned padno, gpp, gpp_offset, offset;
+ unsigned padno, gpp, offset, group;
void __iomem *padown;
community = intel_get_community(pctrl, pin);
return true;
padno = pin_to_padno(community, pin);
- gpp = padno / NPADS_IN_GPP;
- gpp_offset = padno % NPADS_IN_GPP;
- offset = community->padown_offset + gpp * 16 + (gpp_offset / 8) * 4;
+ group = padno / community->gpp_size;
+ gpp = PADOWN_GPP(padno % community->gpp_size);
+ offset = community->padown_offset + 0x10 * group + gpp * 4;
padown = community->regs + offset;
return !(readl(padown) & PADOWN_MASK(padno));
return false;
padno = pin_to_padno(community, pin);
- gpp = padno / NPADS_IN_GPP;
+ gpp = padno / community->gpp_size;
offset = community->hostown_offset + gpp * 4;
hostown = community->regs + offset;
- return !(readl(hostown) & BIT(padno % NPADS_IN_GPP));
+ return !(readl(hostown) & BIT(padno % community->gpp_size));
}
static bool intel_pad_locked(struct intel_pinctrl *pctrl, unsigned pin)
return false;
padno = pin_to_padno(community, pin);
- gpp = padno / NPADS_IN_GPP;
+ gpp = padno / community->gpp_size;
/*
* If PADCFGLOCK and PADCFGLOCKTX bits are both clear for this pad,
*/
offset = community->padcfglock_offset + gpp * 8;
value = readl(community->regs + offset);
- if (value & BIT(pin % NPADS_IN_GPP))
+ if (value & BIT(pin % community->gpp_size))
return true;
offset = community->padcfglock_offset + 4 + gpp * 8;
value = readl(community->regs + offset);
- if (value & BIT(pin % NPADS_IN_GPP))
+ if (value & BIT(pin % community->gpp_size))
return true;
return false;
community = intel_get_community(pctrl, pin);
if (community) {
unsigned padno = pin_to_padno(community, pin);
- unsigned gpp_offset = padno % NPADS_IN_GPP;
- unsigned gpp = padno / NPADS_IN_GPP;
+ unsigned gpp_offset = padno % community->gpp_size;
+ unsigned gpp = padno / community->gpp_size;
writel(BIT(gpp_offset), community->regs + GPI_IS + gpp * 4);
}
community = intel_get_community(pctrl, pin);
if (community) {
unsigned padno = pin_to_padno(community, pin);
- unsigned gpp_offset = padno % NPADS_IN_GPP;
- unsigned gpp = padno / NPADS_IN_GPP;
+ unsigned gpp_offset = padno % community->gpp_size;
+ unsigned gpp = padno / community->gpp_size;
void __iomem *reg;
u32 value;
return -EINVAL;
padno = pin_to_padno(community, pin);
- gpp = padno / NPADS_IN_GPP;
- gpp_offset = padno % NPADS_IN_GPP;
+ gpp = padno / community->gpp_size;
+ gpp_offset = padno % community->gpp_size;
/* Clear the existing wake status */
writel(BIT(gpp_offset), community->regs + GPI_GPE_STS + gpp * 4);
/* Only interrupts that are enabled */
pending &= enabled;
- for_each_set_bit(gpp_offset, &pending, NPADS_IN_GPP) {
+ for_each_set_bit(gpp_offset, &pending, community->gpp_size) {
unsigned padno, irq;
/*
* The last group in community can have less pins
* than NPADS_IN_GPP.
*/
- padno = gpp_offset + gpp * NPADS_IN_GPP;
+ padno = gpp_offset + gpp * community->gpp_size;
if (padno >= community->npins)
break;
community->regs = regs;
community->pad_regs = regs + padbar;
- community->ngpps = DIV_ROUND_UP(community->npins, NPADS_IN_GPP);
+ community->ngpps = DIV_ROUND_UP(community->npins,
+ community->gpp_size);
}
irq = platform_get_irq(pdev, 0);
* ACPI).
* @ie_offset: Register offset of GPI_IE from @regs.
* @pin_base: Starting pin of pins in this community
+ * @gpp_size: Maximum number of pads in each group, such as PADCFGLOCK,
+ * HOSTSW_OWN, GPI_IS, GPI_IE, etc.
* @npins: Number of pins in this community
* @regs: Community specific common registers (reserved for core driver)
* @pad_regs: Community specific pad registers (reserved for core driver)
unsigned hostown_offset;
unsigned ie_offset;
unsigned pin_base;
+ unsigned gpp_size;
size_t npins;
void __iomem *regs;
void __iomem *pad_regs;
.padcfglock_offset = SPT_PADCFGLOCK, \
.hostown_offset = SPT_HOSTSW_OWN, \
.ie_offset = SPT_GPI_IE, \
+ .gpp_size = 24, \
.pin_base = (s), \
.npins = ((e) - (s) + 1), \
}
for (rd = rp->domains; rd < rp->domains + rp->nr_domains; rd++) {
/* check if the domain is locked by BIOS */
- if (rapl_read_data_raw(rd, FW_LOCK, false, &locked)) {
+ ret = rapl_read_data_raw(rd, FW_LOCK, false, &locked);
+ if (ret)
+ return ret;
+ if (locked) {
pr_info("RAPL package %d domain %s locked by BIOS\n",
rp->id, rd->name);
- rd->state |= DOMAIN_STATE_BIOS_LOCKED;
+ rd->state |= DOMAIN_STATE_BIOS_LOCKED;
}
}
platform_set_drvdata(pdev, rtc);
+ rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, DA9063_DRVNAME_RTC,
+ &da9063_rtc_ops, THIS_MODULE);
+ if (IS_ERR(rtc->rtc_dev))
+ return PTR_ERR(rtc->rtc_dev);
+
+ da9063_data_to_tm(data, &rtc->alarm_time, rtc);
+ rtc->rtc_sync = false;
+
irq_alarm = platform_get_irq_byname(pdev, "ALARM");
ret = devm_request_threaded_irq(&pdev->dev, irq_alarm, NULL,
da9063_alarm_event,
IRQF_TRIGGER_LOW | IRQF_ONESHOT,
"ALARM", rtc);
- if (ret) {
+ if (ret)
dev_err(&pdev->dev, "Failed to request ALARM IRQ %d: %d\n",
irq_alarm, ret);
- return ret;
- }
-
- rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, DA9063_DRVNAME_RTC,
- &da9063_rtc_ops, THIS_MODULE);
- if (IS_ERR(rtc->rtc_dev))
- return PTR_ERR(rtc->rtc_dev);
- da9063_data_to_tm(data, &rtc->alarm_time, rtc);
- rtc->rtc_sync = false;
return ret;
}
int irq;
};
+/*
+ * The Rockchip calendar used by the RK808 counts November with 31 days. We use
+ * these translation functions to convert its dates to/from the Gregorian
+ * calendar used by the rest of the world. We arbitrarily define Jan 1st, 2016
+ * as the day when both calendars were in sync, and treat all other dates
+ * relative to that.
+ * NOTE: Other system software (e.g. firmware) that reads the same hardware must
+ * implement this exact same conversion algorithm, with the same anchor date.
+ */
+static time64_t nov2dec_transitions(struct rtc_time *tm)
+{
+ return (tm->tm_year + 1900) - 2016 + (tm->tm_mon + 1 > 11 ? 1 : 0);
+}
+
+static void rockchip_to_gregorian(struct rtc_time *tm)
+{
+ /* If it's Nov 31st, rtc_tm_to_time64() will count that like Dec 1st */
+ time64_t time = rtc_tm_to_time64(tm);
+ rtc_time64_to_tm(time + nov2dec_transitions(tm) * 86400, tm);
+}
+
+static void gregorian_to_rockchip(struct rtc_time *tm)
+{
+ time64_t extra_days = nov2dec_transitions(tm);
+ time64_t time = rtc_tm_to_time64(tm);
+ rtc_time64_to_tm(time - extra_days * 86400, tm);
+
+ /* Compensate if we went back over Nov 31st (will work up to 2381) */
+ if (nov2dec_transitions(tm) < extra_days) {
+ if (tm->tm_mon + 1 == 11)
+ tm->tm_mday++; /* This may result in 31! */
+ else
+ rtc_time64_to_tm(time - (extra_days - 1) * 86400, tm);
+ }
+}
+
/* Read current time and date in RTC */
static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
{
tm->tm_mon = (bcd2bin(rtc_data[4] & MONTHS_REG_MSK)) - 1;
tm->tm_year = (bcd2bin(rtc_data[5] & YEARS_REG_MSK)) + 100;
tm->tm_wday = bcd2bin(rtc_data[6] & WEEKS_REG_MSK);
+ rockchip_to_gregorian(tm);
dev_dbg(dev, "RTC date/time %4d-%02d-%02d(%d) %02d:%02d:%02d\n",
1900 + tm->tm_year, tm->tm_mon + 1, tm->tm_mday,
- tm->tm_wday, tm->tm_hour , tm->tm_min, tm->tm_sec);
+ tm->tm_wday, tm->tm_hour, tm->tm_min, tm->tm_sec);
return ret;
}
u8 rtc_data[NUM_TIME_REGS];
int ret;
+ dev_dbg(dev, "set RTC date/time %4d-%02d-%02d(%d) %02d:%02d:%02d\n",
+ 1900 + tm->tm_year, tm->tm_mon + 1, tm->tm_mday,
+ tm->tm_wday, tm->tm_hour, tm->tm_min, tm->tm_sec);
+ gregorian_to_rockchip(tm);
rtc_data[0] = bin2bcd(tm->tm_sec);
rtc_data[1] = bin2bcd(tm->tm_min);
rtc_data[2] = bin2bcd(tm->tm_hour);
rtc_data[4] = bin2bcd(tm->tm_mon + 1);
rtc_data[5] = bin2bcd(tm->tm_year - 100);
rtc_data[6] = bin2bcd(tm->tm_wday);
- dev_dbg(dev, "set RTC date/time %4d-%02d-%02d(%d) %02d:%02d:%02d\n",
- 1900 + tm->tm_year, tm->tm_mon + 1, tm->tm_mday,
- tm->tm_wday, tm->tm_hour , tm->tm_min, tm->tm_sec);
/* Stop RTC while updating the RTC registers */
ret = regmap_update_bits(rk808->regmap, RK808_RTC_CTRL_REG,
alrm->time.tm_mday = bcd2bin(alrm_data[3] & DAYS_REG_MSK);
alrm->time.tm_mon = (bcd2bin(alrm_data[4] & MONTHS_REG_MSK)) - 1;
alrm->time.tm_year = (bcd2bin(alrm_data[5] & YEARS_REG_MSK)) + 100;
+ rockchip_to_gregorian(&alrm->time);
ret = regmap_read(rk808->regmap, RK808_RTC_INT_REG, &int_reg);
if (ret) {
alrm->time.tm_mday, alrm->time.tm_wday, alrm->time.tm_hour,
alrm->time.tm_min, alrm->time.tm_sec);
+ gregorian_to_rockchip(&alrm->time);
alrm_data[0] = bin2bcd(alrm->time.tm_sec);
alrm_data[1] = bin2bcd(alrm->time.tm_min);
alrm_data[2] = bin2bcd(alrm->time.tm_hour);
status = ap_sm_recv(ap_dev);
switch (status.response_code) {
case AP_RESPONSE_NORMAL:
- if (ap_dev->queue_count > 0)
+ if (ap_dev->queue_count > 0) {
+ ap_dev->state = AP_STATE_WORKING;
return AP_WAIT_AGAIN;
+ }
ap_dev->state = AP_STATE_IDLE;
return AP_WAIT_NONE;
case AP_RESPONSE_NO_PENDING_REPLY:
return vq;
}
+static void virtio_ccw_check_activity(struct virtio_ccw_device *vcdev,
+ __u32 activity)
+{
+ if (vcdev->curr_io & activity) {
+ switch (activity) {
+ case VIRTIO_CCW_DOING_READ_FEAT:
+ case VIRTIO_CCW_DOING_WRITE_FEAT:
+ case VIRTIO_CCW_DOING_READ_CONFIG:
+ case VIRTIO_CCW_DOING_WRITE_CONFIG:
+ case VIRTIO_CCW_DOING_WRITE_STATUS:
+ case VIRTIO_CCW_DOING_SET_VQ:
+ case VIRTIO_CCW_DOING_SET_IND:
+ case VIRTIO_CCW_DOING_SET_CONF_IND:
+ case VIRTIO_CCW_DOING_RESET:
+ case VIRTIO_CCW_DOING_READ_VQ_CONF:
+ case VIRTIO_CCW_DOING_SET_IND_ADAPTER:
+ case VIRTIO_CCW_DOING_SET_VIRTIO_REV:
+ vcdev->curr_io &= ~activity;
+ wake_up(&vcdev->wait_q);
+ break;
+ default:
+ /* don't know what to do... */
+ dev_warn(&vcdev->cdev->dev,
+ "Suspicious activity '%08x'\n", activity);
+ WARN_ON(1);
+ break;
+ }
+ }
+}
+
static void virtio_ccw_int_handler(struct ccw_device *cdev,
unsigned long intparm,
struct irb *irb)
if (!vcdev)
return;
+ if (IS_ERR(irb)) {
+ vcdev->err = PTR_ERR(irb);
+ virtio_ccw_check_activity(vcdev, activity);
+ /* Don't poke around indicators, something's wrong. */
+ return;
+ }
/* Check if it's a notification from the host. */
if ((intparm == 0) &&
(scsw_stctl(&irb->scsw) ==
/* Map everything else to -EIO. */
vcdev->err = -EIO;
}
- if (vcdev->curr_io & activity) {
- switch (activity) {
- case VIRTIO_CCW_DOING_READ_FEAT:
- case VIRTIO_CCW_DOING_WRITE_FEAT:
- case VIRTIO_CCW_DOING_READ_CONFIG:
- case VIRTIO_CCW_DOING_WRITE_CONFIG:
- case VIRTIO_CCW_DOING_WRITE_STATUS:
- case VIRTIO_CCW_DOING_SET_VQ:
- case VIRTIO_CCW_DOING_SET_IND:
- case VIRTIO_CCW_DOING_SET_CONF_IND:
- case VIRTIO_CCW_DOING_RESET:
- case VIRTIO_CCW_DOING_READ_VQ_CONF:
- case VIRTIO_CCW_DOING_SET_IND_ADAPTER:
- case VIRTIO_CCW_DOING_SET_VIRTIO_REV:
- vcdev->curr_io &= ~activity;
- wake_up(&vcdev->wait_q);
- break;
- default:
- /* don't know what to do... */
- dev_warn(&cdev->dev, "Suspicious activity '%08x'\n",
- activity);
- WARN_ON(1);
- break;
- }
- }
+ virtio_ccw_check_activity(vcdev, activity);
for_each_set_bit(i, &vcdev->indicators,
sizeof(vcdev->indicators) * BITS_PER_BYTE) {
/* The bit clear must happen before the vring kick. */
struct scsi_device *sdev = to_scsi_device(dev);
int err = 0;
- if (pm && pm->runtime_suspend) {
- err = blk_pre_runtime_suspend(sdev->request_queue);
- if (err)
- return err;
+ err = blk_pre_runtime_suspend(sdev->request_queue);
+ if (err)
+ return err;
+ if (pm && pm->runtime_suspend)
err = pm->runtime_suspend(dev);
- blk_post_runtime_suspend(sdev->request_queue, err);
- }
+ blk_post_runtime_suspend(sdev->request_queue, err);
+
return err;
}
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
int err = 0;
- if (pm && pm->runtime_resume) {
- blk_pre_runtime_resume(sdev->request_queue);
+ blk_pre_runtime_resume(sdev->request_queue);
+ if (pm && pm->runtime_resume)
err = pm->runtime_resume(dev);
- blk_post_runtime_resume(sdev->request_queue, err);
- }
+ blk_post_runtime_resume(sdev->request_queue, err);
+
return err;
}
static int ses_recv_diag(struct scsi_device *sdev, int page_code,
void *buf, int bufflen)
{
+ int ret;
unsigned char cmd[] = {
RECEIVE_DIAGNOSTIC,
1, /* Set PCV bit */
bufflen & 0xff,
0
};
+ unsigned char recv_page_code;
- return scsi_execute_req(sdev, cmd, DMA_FROM_DEVICE, buf, bufflen,
+ ret = scsi_execute_req(sdev, cmd, DMA_FROM_DEVICE, buf, bufflen,
NULL, SES_TIMEOUT, SES_RETRIES, NULL);
+ if (unlikely(!ret))
+ return ret;
+
+ recv_page_code = ((unsigned char *)buf)[0];
+
+ if (likely(recv_page_code == page_code))
+ return ret;
+
+ /* successful diagnostic but wrong page code. This happens to some
+ * USB devices, just print a message and pretend there was an error */
+
+ sdev_printk(KERN_ERR, sdev,
+ "Wrong diagnostic page; asked for %d got %u\n",
+ page_code, recv_page_code);
+
+ return -EINVAL;
}
static int ses_send_diag(struct scsi_device *sdev, int page_code,
if (desc_ptr)
desc_ptr += len;
- if (addl_desc_ptr)
+ if (addl_desc_ptr &&
+ /* only find additional descriptions for specific devices */
+ (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE ||
+ type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE ||
+ type_ptr[0] == ENCLOSURE_COMPONENT_SAS_EXPANDER ||
+ /* these elements are optional */
+ type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_TARGET_PORT ||
+ type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_INITIATOR_PORT ||
+ type_ptr[0] == ENCLOSURE_COMPONENT_CONTROLLER_ELECTRONICS))
addl_desc_ptr += addl_desc_ptr[1] + 2;
}
{
unsigned int val;
- regmap_read(dspi->regmap, SPI_CTAR(dspi->cs), &val);
+ regmap_read(dspi->regmap, SPI_CTAR(0), &val);
return ((val & SPI_FRAME_BITS_MASK) == SPI_FRAME_BITS(8)) ? 0 : 1;
}
return SPI_PUSHR_TXDATA(d16) |
SPI_PUSHR_PCS(dspi->cs) |
- SPI_PUSHR_CTAS(dspi->cs) |
+ SPI_PUSHR_CTAS(0) |
SPI_PUSHR_CONT;
}
*/
if (tx_word && (dspi->len == 1)) {
dspi->dataflags |= TRAN_STATE_WORD_ODD_NUM;
- regmap_update_bits(dspi->regmap, SPI_CTAR(dspi->cs),
+ regmap_update_bits(dspi->regmap, SPI_CTAR(0),
SPI_FRAME_BITS_MASK, SPI_FRAME_BITS(8));
tx_word = 0;
}
if (tx_word && (dspi->len == 1)) {
dspi->dataflags |= TRAN_STATE_WORD_ODD_NUM;
- regmap_update_bits(dspi->regmap, SPI_CTAR(dspi->cs),
+ regmap_update_bits(dspi->regmap, SPI_CTAR(0),
SPI_FRAME_BITS_MASK, SPI_FRAME_BITS(8));
tx_word = 0;
}
regmap_update_bits(dspi->regmap, SPI_MCR,
SPI_MCR_CLR_TXF | SPI_MCR_CLR_RXF,
SPI_MCR_CLR_TXF | SPI_MCR_CLR_RXF);
- regmap_write(dspi->regmap, SPI_CTAR(dspi->cs),
+ regmap_write(dspi->regmap, SPI_CTAR(0),
dspi->cur_chip->ctar_val);
trans_mode = dspi->devtype_data->trans_mode;
if (!dspi->len) {
if (dspi->dataflags & TRAN_STATE_WORD_ODD_NUM) {
regmap_update_bits(dspi->regmap,
- SPI_CTAR(dspi->cs),
+ SPI_CTAR(0),
SPI_FRAME_BITS_MASK,
SPI_FRAME_BITS(16));
dspi->dataflags &= ~TRAN_STATE_WORD_ODD_NUM;
master->bus_num = -1;
master->num_chipselect = 1;
master->dev.class = &spi_master_class;
- master->dev.parent = get_device(dev);
+ master->dev.parent = dev;
spi_master_set_devdata(master, &master[1]);
return master;
kfree(spidev->rx_buffer);
spidev->rx_buffer = NULL;
+ spin_lock_irq(&spidev->spi_lock);
if (spidev->spi)
spidev->speed_hz = spidev->spi->max_speed_hz;
/* ... after we unbound from the underlying device? */
- spin_lock_irq(&spidev->spi_lock);
dofree = (spidev->spi == NULL);
spin_unlock_irq(&spidev->spi_lock);
size_t eol;
size_t tail;
int ret, found = 0;
- bool eof_push = 0;
/* N.B. avoid overrun if nr == 0 */
- n = min(*nr, smp_load_acquire(&ldata->canon_head) - ldata->read_tail);
- if (!n)
+ if (!*nr)
return 0;
+ n = min(*nr + 1, smp_load_acquire(&ldata->canon_head) - ldata->read_tail);
+
tail = ldata->read_tail & (N_TTY_BUF_SIZE - 1);
size = min_t(size_t, tail + n, N_TTY_BUF_SIZE);
n = eol - tail;
if (n > N_TTY_BUF_SIZE)
n += N_TTY_BUF_SIZE;
- n += found;
- c = n;
+ c = n + found;
- if (found && !ldata->push && read_buf(ldata, eol) == __DISABLED_CHAR) {
- n--;
- eof_push = !n && ldata->read_tail != ldata->line_start;
+ if (!found || read_buf(ldata, eol) != __DISABLED_CHAR) {
+ c = min(*nr, c);
+ n = c;
}
n_tty_trace("%s: eol:%zu found:%d n:%zu c:%zu size:%zu more:%zu\n",
ldata->push = 0;
tty_audit_push(tty);
}
- return eof_push ? -EAGAIN : 0;
+ return 0;
}
extern ssize_t redirected_tty_write(struct file *, const char __user *,
if (ldata->icanon && !L_EXTPROC(tty)) {
retval = canon_copy_from_read_buf(tty, &b, &nr);
- if (retval == -EAGAIN) {
- retval = 0;
- continue;
- } else if (retval)
+ if (retval)
break;
} else {
int uncopied;
*/
static int uniphier_serial_dl_read(struct uart_8250_port *up)
{
- return readl(up->port.membase + UNIPHIER_UART_DLR);
+ int offset = UNIPHIER_UART_DLR << up->port.regshift;
+
+ return readl(up->port.membase + offset);
}
static void uniphier_serial_dl_write(struct uart_8250_port *up, int value)
{
- writel(value, up->port.membase + UNIPHIER_UART_DLR);
+ int offset = UNIPHIER_UART_DLR << up->port.regshift;
+
+ writel(value, up->port.membase + offset);
}
static int uniphier_of_serial_setup(struct device *dev, struct uart_port *port,
if (buf && !parse_options(&early_console_dev, buf))
buf = NULL;
+ spin_lock_init(&port->lock);
port->uartclk = BASE_BAUD * 16;
if (port->mapbase)
port->membase = earlycon_map(port->mapbase, 64);
int err;
struct uart_port *port = &early_console_dev.port;
+ spin_lock_init(&port->lock);
port->iotype = UPIO_MEM;
port->mapbase = addr;
port->uartclk = BASE_BAUD * 16;
sg_init_table(sg, 1);
s->rx_buf[i] = buf;
sg_dma_address(sg) = dma;
- sg->length = s->buf_len_rx;
+ sg_dma_len(sg) = s->buf_len_rx;
buf += s->buf_len_rx;
dma += s->buf_len_rx;
uart_handle_dcd_change(port, 1);
}
- for (i = 0; i < bytes_read; i++)
- uart_handle_sysrq_char(port, con_read_page[i]);
+ if (port->sysrq != 0 && *con_read_page) {
+ for (i = 0; i < bytes_read; i++)
+ uart_handle_sysrq_char(port, con_read_page[i]);
+ }
if (port->state == NULL)
continue;
int (*receive_chars)(struct uart_port *port);
};
-static struct sunhv_ops bychar_ops = {
+static const struct sunhv_ops bychar_ops = {
.transmit_chars = transmit_chars_putchar,
.receive_chars = receive_chars_getchar,
};
-static struct sunhv_ops bywrite_ops = {
+static const struct sunhv_ops bywrite_ops = {
.transmit_chars = transmit_chars_write,
.receive_chars = receive_chars_read,
};
-static struct sunhv_ops *sunhv_ops = &bychar_ops;
+static const struct sunhv_ops *sunhv_ops = &bychar_ops;
static struct tty_port *receive_chars(struct uart_port *port)
{
count = disc->ops->receive_buf2(tty, p, f, count);
else {
count = min_t(int, count, tty->receive_room);
- if (count)
+ if (count && disc->ops->receive_buf)
disc->ops->receive_buf(tty, p, f, count);
}
return count;
unsigned delay;
/* Continue a partial initialization */
- if (type == HUB_INIT2)
- goto init2;
- if (type == HUB_INIT3)
+ if (type == HUB_INIT2 || type == HUB_INIT3) {
+ device_lock(hub->intfdev);
+
+ /* Was the hub disconnected while we were waiting? */
+ if (hub->disconnected) {
+ device_unlock(hub->intfdev);
+ kref_put(&hub->kref, hub_release);
+ return;
+ }
+ if (type == HUB_INIT2)
+ goto init2;
goto init3;
+ }
+ kref_get(&hub->kref);
/* The superspeed hub except for root hub has to use Hub Depth
* value as an offset into the route string to locate the bits
queue_delayed_work(system_power_efficient_wq,
&hub->init_work,
msecs_to_jiffies(delay));
+ device_unlock(hub->intfdev);
return; /* Continues at init3: below */
} else {
msleep(delay);
/* Allow autosuspend if it was suppressed */
if (type <= HUB_INIT3)
usb_autopm_put_interface_async(to_usb_interface(hub->intfdev));
+
+ if (type == HUB_INIT2 || type == HUB_INIT3)
+ device_unlock(hub->intfdev);
+
+ kref_put(&hub->kref, hub_release);
}
/* Implement the continuations for the delays above */
* through. Since this has a reasonably high failure rate, we retry
* several times.
*/
- while (retries--) {
+ while (retries) {
+ retries--;
result = usb_control_msg(serial->dev,
usb_sndctrlpipe(serial->dev, 0), 0x22, 0x21,
0x1, 0, NULL, 0, 100);
static void consume_one_event(unsigned cpu,
struct evtchn_fifo_control_block *control_block,
- unsigned priority, unsigned long *ready)
+ unsigned priority, unsigned long *ready,
+ bool drop)
{
struct evtchn_fifo_queue *q = &per_cpu(cpu_queue, cpu);
uint32_t head;
if (head == 0)
clear_bit(priority, ready);
- if (evtchn_fifo_is_pending(port) && !evtchn_fifo_is_masked(port))
- handle_irq_for_port(port);
+ if (evtchn_fifo_is_pending(port) && !evtchn_fifo_is_masked(port)) {
+ if (unlikely(drop))
+ pr_warn("Dropping pending event for port %u\n", port);
+ else
+ handle_irq_for_port(port);
+ }
q->head[priority] = head;
}
-static void evtchn_fifo_handle_events(unsigned cpu)
+static void __evtchn_fifo_handle_events(unsigned cpu, bool drop)
{
struct evtchn_fifo_control_block *control_block;
unsigned long ready;
while (ready) {
q = find_first_bit(&ready, EVTCHN_FIFO_MAX_QUEUES);
- consume_one_event(cpu, control_block, q, &ready);
+ consume_one_event(cpu, control_block, q, &ready, drop);
ready |= xchg(&control_block->ready, 0);
}
}
+static void evtchn_fifo_handle_events(unsigned cpu)
+{
+ __evtchn_fifo_handle_events(cpu, false);
+}
+
static void evtchn_fifo_resume(void)
{
unsigned cpu;
if (!per_cpu(cpu_control_block, cpu))
ret = evtchn_fifo_alloc_control_block(cpu);
break;
+ case CPU_DEAD:
+ __evtchn_fifo_handle_events(cpu, true);
+ break;
default:
break;
}
struct xen_pci_sharedinfo *sh_info;
unsigned long flags;
struct work_struct op_work;
+ struct xen_pci_op op;
};
struct xen_pcibk_dev_data {
enable ? "enable" : "disable");
if (enable) {
+ /*
+ * The MSI or MSI-X should not have an IRQ handler. Otherwise
+ * if the guest terminates we BUG_ON in free_msi_irqs.
+ */
+ if (dev->msi_enabled || dev->msix_enabled)
+ goto out;
+
rc = request_irq(dev_data->irq,
xen_pcibk_guest_interrupt, IRQF_SHARED,
dev_data->irq_name, dev);
if (unlikely(verbose_request))
printk(KERN_DEBUG DRV_NAME ": %s: enable MSI\n", pci_name(dev));
- status = pci_enable_msi(dev);
+ if (dev->msi_enabled)
+ status = -EALREADY;
+ else if (dev->msix_enabled)
+ status = -ENXIO;
+ else
+ status = pci_enable_msi(dev);
if (status) {
pr_warn_ratelimited("%s: error enabling MSI for guest %u: err %d\n",
int xen_pcibk_disable_msi(struct xen_pcibk_device *pdev,
struct pci_dev *dev, struct xen_pci_op *op)
{
- struct xen_pcibk_dev_data *dev_data;
-
if (unlikely(verbose_request))
printk(KERN_DEBUG DRV_NAME ": %s: disable MSI\n",
pci_name(dev));
- pci_disable_msi(dev);
+ if (dev->msi_enabled) {
+ struct xen_pcibk_dev_data *dev_data;
+
+ pci_disable_msi(dev);
+
+ dev_data = pci_get_drvdata(dev);
+ if (dev_data)
+ dev_data->ack_intr = 1;
+ }
op->value = dev->irq ? xen_pirq_from_irq(dev->irq) : 0;
if (unlikely(verbose_request))
printk(KERN_DEBUG DRV_NAME ": %s: MSI: %d\n", pci_name(dev),
op->value);
- dev_data = pci_get_drvdata(dev);
- if (dev_data)
- dev_data->ack_intr = 1;
return 0;
}
struct xen_pcibk_dev_data *dev_data;
int i, result;
struct msix_entry *entries;
+ u16 cmd;
if (unlikely(verbose_request))
printk(KERN_DEBUG DRV_NAME ": %s: enable MSI-X\n",
pci_name(dev));
+
if (op->value > SH_INFO_MAX_VEC)
return -EINVAL;
+ if (dev->msix_enabled)
+ return -EALREADY;
+
+ /*
+ * PCI_COMMAND_MEMORY must be enabled, otherwise we may not be able
+ * to access the BARs where the MSI-X entries reside.
+ */
+ pci_read_config_word(dev, PCI_COMMAND, &cmd);
+ if (dev->msi_enabled || !(cmd & PCI_COMMAND_MEMORY))
+ return -ENXIO;
+
entries = kmalloc(op->value * sizeof(*entries), GFP_KERNEL);
if (entries == NULL)
return -ENOMEM;
int xen_pcibk_disable_msix(struct xen_pcibk_device *pdev,
struct pci_dev *dev, struct xen_pci_op *op)
{
- struct xen_pcibk_dev_data *dev_data;
if (unlikely(verbose_request))
printk(KERN_DEBUG DRV_NAME ": %s: disable MSI-X\n",
pci_name(dev));
- pci_disable_msix(dev);
+ if (dev->msix_enabled) {
+ struct xen_pcibk_dev_data *dev_data;
+
+ pci_disable_msix(dev);
+
+ dev_data = pci_get_drvdata(dev);
+ if (dev_data)
+ dev_data->ack_intr = 1;
+ }
/*
* SR-IOV devices (which don't have any legacy IRQ) have
* an undefined IRQ value of zero.
*/
op->value = dev->irq ? xen_pirq_from_irq(dev->irq) : 0;
if (unlikely(verbose_request))
- printk(KERN_DEBUG DRV_NAME ": %s: MSI-X: %d\n", pci_name(dev),
- op->value);
- dev_data = pci_get_drvdata(dev);
- if (dev_data)
- dev_data->ack_intr = 1;
+ printk(KERN_DEBUG DRV_NAME ": %s: MSI-X: %d\n",
+ pci_name(dev), op->value);
return 0;
}
#endif
container_of(data, struct xen_pcibk_device, op_work);
struct pci_dev *dev;
struct xen_pcibk_dev_data *dev_data = NULL;
- struct xen_pci_op *op = &pdev->sh_info->op;
+ struct xen_pci_op *op = &pdev->op;
int test_intx = 0;
+ *op = pdev->sh_info->op;
+ barrier();
dev = xen_pcibk_get_pci_dev(pdev, op->domain, op->bus, op->devfn);
if (dev == NULL)
if ((dev_data->enable_intx != test_intx))
xen_pcibk_control_isr(dev, 0 /* no reset */);
}
+ pdev->sh_info->op.err = op->err;
+ pdev->sh_info->op.value = op->value;
+#ifdef CONFIG_PCI_MSI
+ if (op->cmd == XEN_PCI_OP_enable_msix && op->err == 0) {
+ unsigned int i;
+
+ for (i = 0; i < op->value; i++)
+ pdev->sh_info->op.msix_entries[i].vector =
+ op->msix_entries[i].vector;
+ }
+#endif
/* Tell the driver domain that we're done. */
wmb();
clear_bit(_XEN_PCIF_active, (unsigned long *)&pdev->sh_info->flags);
dev_dbg(&xdev->dev, "allocated pdev @ 0x%p\n", pdev);
pdev->xdev = xdev;
- dev_set_drvdata(&xdev->dev, pdev);
mutex_init(&pdev->dev_lock);
kfree(pdev);
pdev = NULL;
}
+
+ dev_set_drvdata(&xdev->dev, pdev);
+
out:
return pdev;
}
if (!pending_req)
return 1;
- ring_req = *RING_GET_REQUEST(ring, rc);
+ RING_COPY_REQUEST(ring, rc, &ring_req);
ring->req_cons = ++rc;
err = prepare_pending_reqs(info, &ring_req, pending_req);
* until transaction commit to do the actual discard.
*/
if (trimming) {
- WARN_ON(!list_empty(&block_group->bg_list));
- spin_lock(&trans->transaction->deleted_bgs_lock);
+ spin_lock(&fs_info->unused_bgs_lock);
+ /*
+ * A concurrent scrub might have added us to the list
+ * fs_info->unused_bgs, so use a list_move operation
+ * to add the block group to the deleted_bgs list.
+ */
list_move(&block_group->bg_list,
&trans->transaction->deleted_bgs);
- spin_unlock(&trans->transaction->deleted_bgs_lock);
+ spin_unlock(&fs_info->unused_bgs_lock);
btrfs_get_block_group(block_group);
}
end_trans:
* on error we return an unlocked page and the error value
* on success we return a locked page and 0
*/
-static int prepare_uptodate_page(struct page *page, u64 pos,
+static int prepare_uptodate_page(struct inode *inode,
+ struct page *page, u64 pos,
bool force_uptodate)
{
int ret = 0;
unlock_page(page);
return -EIO;
}
+ if (page->mapping != inode->i_mapping) {
+ unlock_page(page);
+ return -EAGAIN;
+ }
}
return 0;
}
int faili;
for (i = 0; i < num_pages; i++) {
+again:
pages[i] = find_or_create_page(inode->i_mapping, index + i,
mask | __GFP_WRITE);
if (!pages[i]) {
}
if (i == 0)
- err = prepare_uptodate_page(pages[i], pos,
+ err = prepare_uptodate_page(inode, pages[i], pos,
force_uptodate);
- if (i == num_pages - 1)
- err = prepare_uptodate_page(pages[i],
+ if (!err && i == num_pages - 1)
+ err = prepare_uptodate_page(inode, pages[i],
pos + write_bytes, false);
if (err) {
page_cache_release(pages[i]);
+ if (err == -EAGAIN) {
+ err = 0;
+ goto again;
+ }
faili = i - 1;
goto fail;
}
spin_unlock(&block_group->lock);
ret = 0;
- btrfs_warn(fs_info, "failed to load free space cache for block group %llu, rebuild it now",
+ btrfs_warn(fs_info, "failed to load free space cache for block group %llu, rebuilding it now",
block_group->key.objectid);
}
u64 cont1_bytes, u64 min_bytes)
{
struct btrfs_free_space_ctl *ctl = block_group->free_space_ctl;
- struct btrfs_free_space *entry;
+ struct btrfs_free_space *entry = NULL;
int ret = -ENOSPC;
u64 bitmap_offset = offset_to_bitmap(ctl, offset);
* The bitmap that covers offset won't be in the list unless offset
* is just its start offset.
*/
- entry = list_first_entry(bitmaps, struct btrfs_free_space, list);
- if (entry->offset != bitmap_offset) {
+ if (!list_empty(bitmaps))
+ entry = list_first_entry(bitmaps, struct btrfs_free_space, list);
+
+ if (!entry || entry->offset != bitmap_offset) {
entry = tree_search_offset(ctl, bitmap_offset, 1, 0);
if (entry && list_empty(&entry->list))
list_add(&entry->list, bitmaps);
cur_trans->num_dirty_bgs = 0;
spin_lock_init(&cur_trans->dirty_bgs_lock);
INIT_LIST_HEAD(&cur_trans->deleted_bgs);
- spin_lock_init(&cur_trans->deleted_bgs_lock);
spin_lock_init(&cur_trans->dropped_roots_lock);
list_add_tail(&cur_trans->list, &fs_info->trans_list);
extent_io_tree_init(&cur_trans->dirty_pages,
*/
struct mutex cache_write_mutex;
spinlock_t dirty_bgs_lock;
+ /* Protected by spin lock fs_info->unused_bgs_lock. */
struct list_head deleted_bgs;
- spinlock_t deleted_bgs_lock;
spinlock_t dropped_roots_lock;
struct btrfs_delayed_ref_root delayed_refs;
int aborted;
ret = btrfs_force_chunk_alloc(trans, chunk_root,
BTRFS_BLOCK_GROUP_DATA);
+ btrfs_end_transaction(trans, chunk_root);
if (ret < 0) {
mutex_unlock(&fs_info->delete_unused_bgs_mutex);
goto error;
}
-
- btrfs_end_transaction(trans, chunk_root);
chunk_reserved = 1;
}
mutex_lock(&ls->ls_mutex);
nfs4_inc_and_copy_stateid(&ls->ls_recall_sid, &ls->ls_stid);
+ mutex_unlock(&ls->ls_mutex);
}
static int
trace_layout_recall_release(&ls->ls_stid.sc_stateid);
- mutex_unlock(&ls->ls_mutex);
nfsd4_return_all_layouts(ls, &reaplist);
nfsd4_free_layouts(&reaplist);
nfs4_put_stid(&ls->ls_stid);
mm = get_task_mm(task);
if (!mm)
goto out_no_mm;
+ ret = 0;
for (i = 0, mask = 1; i < MMF_DUMP_FILTER_BITS; i++, mask <<= 1) {
if (val & mask)
/* A few generic types ... taken from ses-2 */
enum enclosure_component_type {
ENCLOSURE_COMPONENT_DEVICE = 0x01,
+ ENCLOSURE_COMPONENT_CONTROLLER_ELECTRONICS = 0x07,
+ ENCLOSURE_COMPONENT_SCSI_TARGET_PORT = 0x14,
+ ENCLOSURE_COMPONENT_SCSI_INITIATOR_PORT = 0x15,
ENCLOSURE_COMPONENT_ARRAY_DEVICE = 0x17,
+ ENCLOSURE_COMPONENT_SAS_EXPANDER = 0x18,
};
/* ses-2 common element status */
#ifndef LINUX_MM_DEBUG_H
#define LINUX_MM_DEBUG_H 1
+#include <linux/bug.h>
#include <linux/stringify.h>
struct page;
#define RING_GET_REQUEST(_r, _idx) \
(&((_r)->sring->ring[((_idx) & (RING_SIZE(_r) - 1))].req))
+/*
+ * Get a local copy of a request.
+ *
+ * Use this in preference to RING_GET_REQUEST() so all processing is
+ * done on a local copy that cannot be modified by the other end.
+ *
+ * Note that https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145 may cause this
+ * to be ineffective where _req is a struct which consists of only bitfields.
+ */
+#define RING_COPY_REQUEST(_r, _idx, _req) do { \
+ /* Use volatile to force the copy into _req. */ \
+ *(_req) = *(volatile typeof(_req))RING_GET_REQUEST(_r, _idx); \
+} while (0)
+
#define RING_GET_RESPONSE(_r, _idx) \
(&((_r)->sring->ring[((_idx) & (RING_SIZE(_r) - 1))].rsp))
return last;
}
+/* type and compressor must be null-terminated */
static struct zswap_pool *zswap_pool_find_get(char *type, char *compressor)
{
struct zswap_pool *pool;
assert_spin_locked(&zswap_pools_lock);
list_for_each_entry_rcu(pool, &zswap_pools, list) {
- if (strncmp(pool->tfm_name, compressor, sizeof(pool->tfm_name)))
+ if (strcmp(pool->tfm_name, compressor))
continue;
- if (strncmp(zpool_get_type(pool->zpool), type,
- sizeof(zswap_zpool_type)))
+ if (strcmp(zpool_get_type(pool->zpool), type))
continue;
/* if we can't get it, it's about to be destroyed */
if (!zswap_pool_get(pool))
static int fd_map; /* File descriptor for file being modified. */
static int mmap_failed; /* Boolean flag. */
-static void *ehdr_curr; /* current ElfXX_Ehdr * for resource cleanup */
static char gpfx; /* prefix for global symbol name (sometimes '_') */
static struct stat sb; /* Remember .st_size, etc. */
static jmp_buf jmpenv; /* setjmp/longjmp per-file error escape */
static const char *altmcount; /* alternate mcount symbol name */
static int warn_on_notrace_sect; /* warn when section has mcount not being recorded */
+static void *file_map; /* pointer of the mapped file */
+static void *file_end; /* pointer to the end of the mapped file */
+static int file_updated; /* flag to state file was changed */
+static void *file_ptr; /* current file pointer location */
+static void *file_append; /* added to the end of the file */
+static size_t file_append_size; /* how much is added to end of file */
/* setjmp() return values */
enum {
cleanup(void)
{
if (!mmap_failed)
- munmap(ehdr_curr, sb.st_size);
+ munmap(file_map, sb.st_size);
else
- free(ehdr_curr);
- close(fd_map);
+ free(file_map);
+ file_map = NULL;
+ free(file_append);
+ file_append = NULL;
+ file_append_size = 0;
+ file_updated = 0;
}
static void __attribute__((noreturn))
static off_t
ulseek(int const fd, off_t const offset, int const whence)
{
- off_t const w = lseek(fd, offset, whence);
- if (w == (off_t)-1) {
- perror("lseek");
+ switch (whence) {
+ case SEEK_SET:
+ file_ptr = file_map + offset;
+ break;
+ case SEEK_CUR:
+ file_ptr += offset;
+ break;
+ case SEEK_END:
+ file_ptr = file_map + (sb.st_size - offset);
+ break;
+ }
+ if (file_ptr < file_map) {
+ fprintf(stderr, "lseek: seek before file\n");
fail_file();
}
- return w;
+ return file_ptr - file_map;
}
static size_t
static size_t
uwrite(int const fd, void const *const buf, size_t const count)
{
- size_t const n = write(fd, buf, count);
- if (n != count) {
- perror("write");
- fail_file();
+ size_t cnt = count;
+ off_t idx = 0;
+
+ file_updated = 1;
+
+ if (file_ptr + count >= file_end) {
+ off_t aoffset = (file_ptr + count) - file_end;
+
+ if (aoffset > file_append_size) {
+ file_append = realloc(file_append, aoffset);
+ file_append_size = aoffset;
+ }
+ if (!file_append) {
+ perror("write");
+ fail_file();
+ }
+ if (file_ptr < file_end) {
+ cnt = file_end - file_ptr;
+ } else {
+ cnt = 0;
+ idx = aoffset - count;
+ }
}
- return n;
+
+ if (cnt)
+ memcpy(file_ptr, buf, cnt);
+
+ if (cnt < count)
+ memcpy(file_append + idx, buf + cnt, count - cnt);
+
+ file_ptr += count;
+ return count;
}
static void *
*/
static void *mmap_file(char const *fname)
{
- void *addr;
-
- fd_map = open(fname, O_RDWR);
+ fd_map = open(fname, O_RDONLY);
if (fd_map < 0 || fstat(fd_map, &sb) < 0) {
perror(fname);
fail_file();
fprintf(stderr, "not a regular file: %s\n", fname);
fail_file();
}
- addr = mmap(0, sb.st_size, PROT_READ|PROT_WRITE, MAP_PRIVATE,
- fd_map, 0);
+ file_map = mmap(0, sb.st_size, PROT_READ|PROT_WRITE, MAP_PRIVATE,
+ fd_map, 0);
mmap_failed = 0;
- if (addr == MAP_FAILED) {
+ if (file_map == MAP_FAILED) {
mmap_failed = 1;
- addr = umalloc(sb.st_size);
- uread(fd_map, addr, sb.st_size);
+ file_map = umalloc(sb.st_size);
+ uread(fd_map, file_map, sb.st_size);
+ }
+ close(fd_map);
+
+ file_end = file_map + sb.st_size;
+
+ return file_map;
+}
+
+static void write_file(const char *fname)
+{
+ char tmp_file[strlen(fname) + 4];
+ size_t n;
+
+ if (!file_updated)
+ return;
+
+ sprintf(tmp_file, "%s.rc", fname);
+
+ /*
+ * After reading the entire file into memory, delete it
+ * and write it back, to prevent weird side effects of modifying
+ * an object file in place.
+ */
+ fd_map = open(tmp_file, O_WRONLY | O_TRUNC | O_CREAT, sb.st_mode);
+ if (fd_map < 0) {
+ perror(fname);
+ fail_file();
+ }
+ n = write(fd_map, file_map, sb.st_size);
+ if (n != sb.st_size) {
+ perror("write");
+ fail_file();
+ }
+ if (file_append_size) {
+ n = write(fd_map, file_append, file_append_size);
+ if (n != file_append_size) {
+ perror("write");
+ fail_file();
+ }
+ }
+ close(fd_map);
+ if (rename(tmp_file, fname) < 0) {
+ perror(fname);
+ fail_file();
}
- return addr;
}
/* w8rev, w8nat, ...: Handle endianness. */
Elf32_Ehdr *const ehdr = mmap_file(fname);
unsigned int reltype = 0;
- ehdr_curr = ehdr;
w = w4nat;
w2 = w2nat;
w8 = w8nat;
}
} /* end switch */
+ write_file(fname);
cleanup();
}
case SJ_SETJMP: /* normal sequence */
/* Avoid problems if early cleanup() */
fd_map = -1;
- ehdr_curr = NULL;
mmap_failed = 1;
+ file_map = NULL;
+ file_ptr = NULL;
+ file_updated = 0;
do_file(file);
break;
case SJ_FAIL: /* error in do_file or below */
+ sprintf("%s: failed\n", file);
++n_error;
break;
case SJ_SUCCEED: /* premature success */
}
#endif /* CONFIG_PM_SLEEP || SUPPORT_VGA_SWITCHEROO */
+#ifdef CONFIG_PM_SLEEP
+/* put codec down to D3 at hibernation for Intel SKL+;
+ * otherwise BIOS may still access the codec and screw up the driver
+ */
+#define IS_SKL(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0xa170)
+#define IS_SKL_LP(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0x9d70)
+#define IS_BXT(pci) ((pci)->vendor == 0x8086 && (pci)->device == 0x5a98)
+#define IS_SKL_PLUS(pci) (IS_SKL(pci) || IS_SKL_LP(pci) || IS_BXT(pci))
+
+static int azx_freeze_noirq(struct device *dev)
+{
+ struct pci_dev *pci = to_pci_dev(dev);
+
+ if (IS_SKL_PLUS(pci))
+ pci_set_power_state(pci, PCI_D3hot);
+
+ return 0;
+}
+
+static int azx_thaw_noirq(struct device *dev)
+{
+ struct pci_dev *pci = to_pci_dev(dev);
+
+ if (IS_SKL_PLUS(pci))
+ pci_set_power_state(pci, PCI_D0);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
#ifdef CONFIG_PM
static int azx_runtime_suspend(struct device *dev)
{
static const struct dev_pm_ops azx_pm = {
SET_SYSTEM_SLEEP_PM_OPS(azx_suspend, azx_resume)
+#ifdef CONFIG_PM_SLEEP
+ .freeze_noirq = azx_freeze_noirq,
+ .thaw_noirq = azx_thaw_noirq,
+#endif
SET_RUNTIME_PM_OPS(azx_runtime_suspend, azx_runtime_resume, azx_runtime_idle)
};
void (*power_hook)(struct hda_codec *codec);
#endif
void (*shutup)(struct hda_codec *codec);
+ void (*reboot_notify)(struct hda_codec *codec);
int init_amp;
int codec_variant; /* flag for other variants */
snd_hda_shutup_pins(codec);
}
+static void alc_reboot_notify(struct hda_codec *codec)
+{
+ struct alc_spec *spec = codec->spec;
+
+ if (spec && spec->reboot_notify)
+ spec->reboot_notify(codec);
+ else
+ alc_shutup(codec);
+}
+
+/* power down codec to D3 at reboot/shutdown; set as reboot_notify ops */
+static void alc_d3_at_reboot(struct hda_codec *codec)
+{
+ snd_hda_codec_set_power_to_all(codec, codec->core.afg, AC_PWRST_D3);
+ snd_hda_codec_write(codec, codec->core.afg, 0,
+ AC_VERB_SET_POWER_STATE, AC_PWRST_D3);
+ msleep(10);
+}
+
#define alc_free snd_hda_gen_free
#ifdef CONFIG_PM
.suspend = alc_suspend,
.check_power_status = snd_hda_gen_check_power_status,
#endif
- .reboot_notify = alc_shutup,
+ .reboot_notify = alc_reboot_notify,
};
ALC889_FIXUP_MBA11_VREF,
ALC889_FIXUP_MBA21_VREF,
ALC889_FIXUP_MP11_VREF,
+ ALC889_FIXUP_MP41_VREF,
ALC882_FIXUP_INV_DMIC,
ALC882_FIXUP_NO_PRIMARY_HP,
ALC887_FIXUP_ASUS_BASS,
const struct hda_fixup *fix, int action)
{
struct alc_spec *spec = codec->spec;
- static hda_nid_t nids[2] = { 0x14, 0x15 };
+ static hda_nid_t nids[3] = { 0x14, 0x15, 0x19 };
int i;
if (action != HDA_FIXUP_ACT_INIT)
.chained = true,
.chain_id = ALC885_FIXUP_MACPRO_GPIO,
},
+ [ALC889_FIXUP_MP41_VREF] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = alc889_fixup_mbp_vref,
+ .chained = true,
+ .chain_id = ALC885_FIXUP_MACPRO_GPIO,
+ },
[ALC882_FIXUP_INV_DMIC] = {
.type = HDA_FIXUP_FUNC,
.v.func = alc_fixup_inv_dmic,
SND_PCI_QUIRK(0x106b, 0x3f00, "Macbook 5,1", ALC889_FIXUP_IMAC91_VREF),
SND_PCI_QUIRK(0x106b, 0x4000, "MacbookPro 5,1", ALC889_FIXUP_IMAC91_VREF),
SND_PCI_QUIRK(0x106b, 0x4100, "Macmini 3,1", ALC889_FIXUP_IMAC91_VREF),
- SND_PCI_QUIRK(0x106b, 0x4200, "Mac Pro 5,1", ALC885_FIXUP_MACPRO_GPIO),
+ SND_PCI_QUIRK(0x106b, 0x4200, "Mac Pro 4,1/5,1", ALC889_FIXUP_MP41_VREF),
SND_PCI_QUIRK(0x106b, 0x4300, "iMac 9,1", ALC889_FIXUP_IMAC91_VREF),
SND_PCI_QUIRK(0x106b, 0x4600, "MacbookPro 5,2", ALC889_FIXUP_IMAC91_VREF),
SND_PCI_QUIRK(0x106b, 0x4900, "iMac 9,1 Aluminum", ALC889_FIXUP_IMAC91_VREF),
struct alc_spec *spec = codec->spec;
if (action == HDA_FIXUP_ACT_PRE_PROBE) {
+ spec->shutup = alc_no_shutup; /* reduce click noise */
+ spec->reboot_notify = alc_d3_at_reboot; /* reduce noise */
spec->parse_flags = HDA_PINCFG_NO_HP_FIXUP;
codec->power_save_node = 0; /* avoid click noises */
snd_hda_apply_pincfgs(codec, pincfgs);
}
}
-/* additional fixup for Thinkpad T440s noise problem */
-static void alc_fixup_tpt440(struct hda_codec *codec,
- const struct hda_fixup *fix, int action)
-{
- struct alc_spec *spec = codec->spec;
-
- if (action == HDA_FIXUP_ACT_PRE_PROBE) {
- spec->shutup = alc_no_shutup; /* reduce click noise */
- spec->gen.mixer_nid = 0; /* reduce background noise */
- }
-}
-
static void alc_shutup_dell_xps13(struct hda_codec *codec)
{
struct alc_spec *spec = codec->spec;
ALC288_FIXUP_DISABLE_AAMIX,
ALC292_FIXUP_DELL_E7X,
ALC292_FIXUP_DISABLE_AAMIX,
+ ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK,
ALC298_FIXUP_DELL1_MIC_NO_PRESENCE,
ALC275_FIXUP_DELL_XPS,
ALC256_FIXUP_DELL_XPS_13_HEADPHONE_NOISE,
},
[ALC292_FIXUP_TPT440] = {
.type = HDA_FIXUP_FUNC,
- .v.func = alc_fixup_tpt440,
+ .v.func = alc_fixup_disable_aamix,
.chained = true,
.chain_id = ALC292_FIXUP_TPT440_DOCK,
},
.chained = true,
.chain_id = ALC269_FIXUP_DELL2_MIC_NO_PRESENCE
},
+ [ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = alc_fixup_disable_aamix,
+ .chained = true,
+ .chain_id = ALC293_FIXUP_DELL1_MIC_NO_PRESENCE
+ },
[ALC292_FIXUP_DELL_E7X] = {
.type = HDA_FIXUP_FUNC,
.v.func = alc_fixup_dell_xps13,
SND_PCI_QUIRK(0x1028, 0x06c7, "Dell", ALC255_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x06d9, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x06da, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
- SND_PCI_QUIRK(0x1028, 0x06db, "Dell", ALC292_FIXUP_DISABLE_AAMIX),
- SND_PCI_QUIRK(0x1028, 0x06dd, "Dell", ALC292_FIXUP_DISABLE_AAMIX),
- SND_PCI_QUIRK(0x1028, 0x06de, "Dell", ALC292_FIXUP_DISABLE_AAMIX),
- SND_PCI_QUIRK(0x1028, 0x06df, "Dell", ALC292_FIXUP_DISABLE_AAMIX),
- SND_PCI_QUIRK(0x1028, 0x06e0, "Dell", ALC292_FIXUP_DISABLE_AAMIX),
+ SND_PCI_QUIRK(0x1028, 0x06db, "Dell", ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK),
+ SND_PCI_QUIRK(0x1028, 0x06dd, "Dell", ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK),
+ SND_PCI_QUIRK(0x1028, 0x06de, "Dell", ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK),
+ SND_PCI_QUIRK(0x1028, 0x06df, "Dell", ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK),
+ SND_PCI_QUIRK(0x1028, 0x06e0, "Dell", ALC293_FIXUP_DISABLE_AAMIX_MULTIJACK),
SND_PCI_QUIRK(0x1028, 0x0704, "Dell XPS 13", ALC256_FIXUP_DELL_XPS_13_HEADPHONE_NOISE),
SND_PCI_QUIRK(0x1028, 0x164a, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x164b, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x17aa, 0x2212, "Thinkpad T440", ALC292_FIXUP_TPT440_DOCK),
SND_PCI_QUIRK(0x17aa, 0x2214, "Thinkpad X240", ALC292_FIXUP_TPT440_DOCK),
SND_PCI_QUIRK(0x17aa, 0x2215, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
+ SND_PCI_QUIRK(0x17aa, 0x2218, "Thinkpad X1 Carbon 2nd", ALC292_FIXUP_TPT440_DOCK),
SND_PCI_QUIRK(0x17aa, 0x2223, "ThinkPad T550", ALC292_FIXUP_TPT440_DOCK),
SND_PCI_QUIRK(0x17aa, 0x2226, "ThinkPad X250", ALC292_FIXUP_TPT440_DOCK),
SND_PCI_QUIRK(0x17aa, 0x2233, "Thinkpad", ALC293_FIXUP_LENOVO_SPK_NOISE),
static const DECLARE_TLV_DB_SCALE(bypass_tlv, -1500, 300, 0);
static const DECLARE_TLV_DB_SCALE(mic_tlv, 0, 300, 0);
-static const int deemph_settings[] = { 0, 32000, 44100, 48000 };
+static const struct {
+ int rate;
+ unsigned int val;
+} deemph_settings[] = {
+ { 0, ES8328_DACCONTROL6_DEEMPH_OFF },
+ { 32000, ES8328_DACCONTROL6_DEEMPH_32k },
+ { 44100, ES8328_DACCONTROL6_DEEMPH_44_1k },
+ { 48000, ES8328_DACCONTROL6_DEEMPH_48k },
+};
static int es8328_set_deemph(struct snd_soc_codec *codec)
{
* rate.
*/
if (es8328->deemph) {
- best = 1;
- for (i = 2; i < ARRAY_SIZE(deemph_settings); i++) {
- if (abs(deemph_settings[i] - es8328->playback_fs) <
- abs(deemph_settings[best] - es8328->playback_fs))
+ best = 0;
+ for (i = 1; i < ARRAY_SIZE(deemph_settings); i++) {
+ if (abs(deemph_settings[i].rate - es8328->playback_fs) <
+ abs(deemph_settings[best].rate - es8328->playback_fs))
best = i;
}
- val = best << 1;
+ val = deemph_settings[best].val;
} else {
- val = 0;
+ val = ES8328_DACCONTROL6_DEEMPH_OFF;
}
dev_dbg(codec->dev, "Set deemphasis %d\n", val);
- return snd_soc_update_bits(codec, ES8328_DACCONTROL6, 0x6, val);
+ return snd_soc_update_bits(codec, ES8328_DACCONTROL6,
+ ES8328_DACCONTROL6_DEEMPH_MASK, val);
}
static int es8328_get_deemph(struct snd_kcontrol *kcontrol,
#define ES8328_DACCONTROL6_CLICKFREE (1 << 3)
#define ES8328_DACCONTROL6_DAC_INVR (1 << 4)
#define ES8328_DACCONTROL6_DAC_INVL (1 << 5)
+#define ES8328_DACCONTROL6_DEEMPH_MASK (3 << 6)
#define ES8328_DACCONTROL6_DEEMPH_OFF (0 << 6)
#define ES8328_DACCONTROL6_DEEMPH_32k (1 << 6)
#define ES8328_DACCONTROL6_DEEMPH_44_1k (2 << 6)
case SND_SOC_DAPM_POST_PMU:
snd_soc_update_bits(codec, SGTL5000_CHIP_ANA_POWER,
SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP);
+ msleep(400);
break;
case SND_SOC_DAPM_PRE_PMD:
.max_register = WM8974_MONOMIX,
.reg_defaults = wm8974_reg_defaults,
.num_reg_defaults = ARRAY_SIZE(wm8974_reg_defaults),
+ .cache_type = REGCACHE_FLAT,
};
static int wm8974_probe(struct snd_soc_codec *codec)
/* wait for XDATA to be cleared */
cnt = 0;
- while (!(mcasp_get_reg(mcasp, DAVINCI_MCASP_TXSTAT_REG) &
- ~XRDATA) && (cnt < 100000))
+ while ((mcasp_get_reg(mcasp, DAVINCI_MCASP_TXSTAT_REG) & XRDATA) &&
+ (cnt < 100000))
cnt++;
/* Release TX state machine */
FSL_SAI_CSR_FR, FSL_SAI_CSR_FR);
regmap_update_bits(sai->regmap, FSL_SAI_RCSR,
FSL_SAI_CSR_FR, FSL_SAI_CSR_FR);
+
+ /*
+ * For sai master mode, after several open/close sai,
+ * there will be no frame clock, and can't recover
+ * anymore. Add software reset to fix this issue.
+ * This is a hardware bug, and will be fix in the
+ * next sai version.
+ */
+ if (!sai->is_slave_mode) {
+ /* Software Reset for both Tx and Rx */
+ regmap_write(sai->regmap,
+ FSL_SAI_TCSR, FSL_SAI_CSR_SR);
+ regmap_write(sai->regmap,
+ FSL_SAI_RCSR, FSL_SAI_CSR_SR);
+ /* Clear SR bit to finish the reset */
+ regmap_write(sai->regmap, FSL_SAI_TCSR, 0);
+ regmap_write(sai->regmap, FSL_SAI_RCSR, 0);
+ }
}
break;
default:
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
ret = regmap_update_bits(spdif->regmap, SPDIF_DMACR,
- SPDIF_DMACR_TDE_ENABLE,
- SPDIF_DMACR_TDE_ENABLE);
+ SPDIF_DMACR_TDE_ENABLE |
+ SPDIF_DMACR_TDL_MASK,
+ SPDIF_DMACR_TDE_ENABLE |
+ SPDIF_DMACR_TDL(16));
if (ret != 0)
return ret;
#define SPDIF_DMACR_TDL_SHIFT 0
#define SPDIF_DMACR_TDL(x) ((x) << SPDIF_DMACR_TDL_SHIFT)
-#define SPDIF_DMACR_TDL_MASK (0x1f << SDPIF_DMACR_TDL_SHIFT)
+#define SPDIF_DMACR_TDL_MASK (0x1f << SPDIF_DMACR_TDL_SHIFT)
/*
* XFER
}
}
+ snd_usb_mixer_fu_apply_quirk(state->mixer, cval, unitid, kctl);
+
range = (cval->max - cval->min) / cval->res;
/*
* Are there devices with volume range more than 255? I use a bit more
{ 0 } /* terminator */
};
-/* Dragonfly DAC 1.2, the dB conversion factor is 1 instead of 256 */
-static struct usbmix_dB_map dragonfly_1_2_dB = {0, 5000};
-static struct usbmix_name_map dragonfly_1_2_map[] = {
- { 7, NULL, .dB = &dragonfly_1_2_dB },
- { 0 } /* terminator */
-};
-
/*
* Control map entries
*/
.id = USB_ID(0x05a7, 0x1020),
.map = bose_companion5_map,
},
- {
- /* Dragonfly DAC 1.2 */
- .id = USB_ID(0x21b4, 0x0081),
- .map = dragonfly_1_2_map,
- },
{ 0 } /* terminator */
};
#include <sound/control.h>
#include <sound/hwdep.h>
#include <sound/info.h>
+#include <sound/tlv.h>
#include "usbaudio.h"
#include "mixer.h"
}
}
+static void snd_dragonfly_quirk_db_scale(struct usb_mixer_interface *mixer,
+ struct snd_kcontrol *kctl)
+{
+ /* Approximation using 10 ranges based on output measurement on hw v1.2.
+ * This seems close to the cubic mapping e.g. alsamixer uses. */
+ static const DECLARE_TLV_DB_RANGE(scale,
+ 0, 1, TLV_DB_MINMAX_ITEM(-5300, -4970),
+ 2, 5, TLV_DB_MINMAX_ITEM(-4710, -4160),
+ 6, 7, TLV_DB_MINMAX_ITEM(-3884, -3710),
+ 8, 14, TLV_DB_MINMAX_ITEM(-3443, -2560),
+ 15, 16, TLV_DB_MINMAX_ITEM(-2475, -2324),
+ 17, 19, TLV_DB_MINMAX_ITEM(-2228, -2031),
+ 20, 26, TLV_DB_MINMAX_ITEM(-1910, -1393),
+ 27, 31, TLV_DB_MINMAX_ITEM(-1322, -1032),
+ 32, 40, TLV_DB_MINMAX_ITEM(-968, -490),
+ 41, 50, TLV_DB_MINMAX_ITEM(-441, 0),
+ );
+
+ usb_audio_info(mixer->chip, "applying DragonFly dB scale quirk\n");
+ kctl->tlv.p = scale;
+ kctl->vd[0].access |= SNDRV_CTL_ELEM_ACCESS_TLV_READ;
+ kctl->vd[0].access &= ~SNDRV_CTL_ELEM_ACCESS_TLV_CALLBACK;
+}
+
+void snd_usb_mixer_fu_apply_quirk(struct usb_mixer_interface *mixer,
+ struct usb_mixer_elem_info *cval, int unitid,
+ struct snd_kcontrol *kctl)
+{
+ switch (mixer->chip->usb_id) {
+ case USB_ID(0x21b4, 0x0081): /* AudioQuest DragonFly */
+ if (unitid == 7 && cval->min == 0 && cval->max == 50)
+ snd_dragonfly_quirk_db_scale(mixer, kctl);
+ break;
+ }
+}
+
void snd_usb_mixer_rc_memory_change(struct usb_mixer_interface *mixer,
int unitid);
+void snd_usb_mixer_fu_apply_quirk(struct usb_mixer_interface *mixer,
+ struct usb_mixer_elem_info *cval, int unitid,
+ struct snd_kcontrol *kctl);
+
#endif /* SND_USB_MIXER_QUIRKS_H */
case USB_ID(0x045E, 0x0779): /* MS Lifecam HD-3000 */
case USB_ID(0x04D8, 0xFEEA): /* Benchmark DAC1 Pre */
case USB_ID(0x074D, 0x3553): /* Outlaw RR2150 (Micronas UAC3553B) */
+ case USB_ID(0x21B4, 0x0081): /* AudioQuest DragonFly */
return true;
}
return false;
return true;
}
- return dist_active_irq(vcpu);
+ return vgic_irq_is_active(vcpu, map->virt_irq);
}
/*
projects / linux-drm-fsl-dcu.git / commitdiff