#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
#include <linux/usb/isp1362.h>
#endif
#include <asm/irq.h>
* Driver needs to know address, irq and flag pin.
*/
#if defined(CONFIG_BFIN532_IP0X)
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
#include <linux/dm9000.h>
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0, /* if 1 - block!!! */
};
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 2,
};
#endif /* spi master and devices */
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
static struct resource isp1362_hcd_resources[] = {
{
.start = 0x20300000,
static struct platform_device *ip0x_devices[] __initdata = {
#if defined(CONFIG_BFIN532_IP0X)
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+#if IS_ENABLED(CONFIG_DM9000)
&dm9000_device1,
&dm9000_device2,
#endif
#endif
-#if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
+#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&spi_bfin_master_device,
#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
&isp1362_hcd_device,
#endif
};