linux-drm-fsl-dcu.git
5 years agocpufreq: speedstep-smi: enable interrupts when waiting
Mikulas Patocka [Mon, 9 Feb 2015 18:38:17 +0000 (13:38 -0500)]
cpufreq: speedstep-smi: enable interrupts when waiting

On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.

The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.

This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agoMerge branch 'sfi' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux into...
Rafael J. Wysocki [Mon, 9 Feb 2015 22:43:53 +0000 (23:43 +0100)]
Merge branch 'sfi' of git://git./linux/kernel/git/lenb/linux into pm-cpufreq

Pull SFI-based cpufreq driver for v3.20 from Len Brown.

* 'sfi' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  cpufreq: Add SFI based cpufreq driver support
  SFI: fix compiler warnings

5 years agointel_pstate: provide option to only use intel_pstate with HWP
Kristen Carlson Accardi [Fri, 6 Feb 2015 21:41:55 +0000 (13:41 -0800)]
intel_pstate: provide option to only use intel_pstate with HWP

Allow users the option to disable the driver for any hardware
which does not support HWP.

Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq-dt: Drop unnecessary check before cpufreq_cooling_unregister() invocation
Markus Elfring [Tue, 3 Feb 2015 18:21:21 +0000 (19:21 +0100)]
cpufreq-dt: Drop unnecessary check before cpufreq_cooling_unregister() invocation

The cpufreq_cooling_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: Create for_each_governor()
Viresh Kumar [Tue, 27 Jan 2015 08:36:09 +0000 (14:06 +0530)]
cpufreq: Create for_each_governor()

To make code more readable and less error prone, lets create a helper macro for
iterating over all available governors.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: Create for_each_policy()
Viresh Kumar [Tue, 27 Jan 2015 08:36:08 +0000 (14:06 +0530)]
cpufreq: Create for_each_policy()

To make code more readable and less error prone, lets create a helper macro for
iterating over all active policies.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: Drop cpufreq_disabled() check from cpufreq_cpu_{get|put}()
Viresh Kumar [Tue, 27 Jan 2015 08:36:07 +0000 (14:06 +0530)]
cpufreq: Drop cpufreq_disabled() check from cpufreq_cpu_{get|put}()

When cpufreq is disabled, the per-cpu variable would have been set to
NULL. Remove this unnecessary check.

[ Changelog from Saravana Kannan. ]

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: Set cpufreq_cpu_data to NULL before putting kobject
Viresh Kumar [Sat, 31 Jan 2015 00:32:44 +0000 (06:02 +0530)]
cpufreq: Set cpufreq_cpu_data to NULL before putting kobject

In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs
to be cleared before calling kobject_put(&policy->kobj) and under
cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get()
in parallel with it, they can obtain a non-NULL policy from that after
kobject_put(&policy->kobj) was executed.

Consider this case:

Thread A Thread B
cpufreq_cpu_get()
  acquire cpufreq_driver_lock
  read-per-cpu cpufreq_cpu_data
kobject_put(&policy->kobj);
  kobject_get(&policy->kobj);
...
per_cpu(&cpufreq_cpu_data, cpu) = NULL

And this will result in a warning like this one:

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47
 kobject_get+0x41/0x50()
 Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl
 lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon
 ...
 Call Trace:
  [<ffffffff81661b14>] dump_stack+0x46/0x58
  [<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0
  [<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20
  [<ffffffff812e16d1>] kobject_get+0x41/0x50
  [<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0
  [<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0
  [<ffffffff810b8cb2>] ? up+0x32/0x50
  [<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2
  [<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252
  [<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0
  [<ffffffff81360967>] ? acpi_has_method+0x25/0x40
  [<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82
  [<ffffffff81089566>] ? move_linked_works+0x66/0x90
  [<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7
  [<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c
  [<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22
  [<ffffffff8108c910>] process_one_work+0x160/0x410
  [<ffffffff8108d05b>] worker_thread+0x11b/0x520
  [<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380
  [<ffffffff81092421>] kthread+0xe1/0x100
  [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
  [<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0
  [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
 ---[ end trace 89e66eb9795efdf7 ]---

The actual code flow is as follows:

 Thread A: Workqueue: kacpi_notify

 acpi_processor_notify()
   acpi_processor_ppc_has_changed()
         cpufreq_update_policy()
           cpufreq_cpu_get()
             kobject_get()

 Thread B: xenbus_thread()

 xenbus_thread()
   msg->u.watch.handle->callback()
     handle_vcpu_hotplug_event()
       vcpu_hotplug()
         cpu_down()
           __cpu_notify(CPU_POST_DEAD..)
             cpufreq_cpu_callback()
               __cpufreq_remove_dev_finish()
                 cpufreq_policy_put_kobj()
                   kobject_put()

cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data
under cpufreq_driver_lock, and once it gets a valid policy it expects it
to not be freed until cpufreq_cpu_put() is called.

But the race happens when another thread puts the kobject first and updates
cpufreq_cpu_data before or later. And so the first thread gets a valid policy
structure and before it does kobject_get() on it, the second one has already
done kobject_put().

Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that
too under locks.

Reported-by: Ethan Zhao <ethan.zhao@oracle.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agointel_pstate: honor user space min_perf_pct override on resume
Kristen Carlson Accardi [Thu, 29 Jan 2015 21:03:52 +0000 (13:03 -0800)]
intel_pstate: honor user space min_perf_pct override on resume

If the user has requested an override of the min_perf_pct via
sysfs, then it should be restored whenever policy is updated,
such as on resume.  Take the max of whatever the user requested
and whatever the policy is.

Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agointel_pstate: respect cpufreq policy request
Srinivas Pandruvada [Thu, 29 Jan 2015 20:17:13 +0000 (12:17 -0800)]
intel_pstate: respect cpufreq policy request

When thermal or other subsystem requests to change the policy,
use that irrepective of whether cpufreq policy is PERFORMANCE or
not. Without this change, when thermal subsystem passive policy wants
to reduce performance, it still runs at 100%.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agointel_pstate: Add num_pstates to sysfs
Kristen Carlson Accardi [Wed, 28 Jan 2015 23:03:28 +0000 (15:03 -0800)]
intel_pstate: Add num_pstates to sysfs

Add a sysfs interface to display the total number of supported
pstates.  This value is independent of whether turbo has been
enabled or disabled.

Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agointel_pstate: expose turbo range to sysfs
Kristen Carlson Accardi [Wed, 28 Jan 2015 23:03:27 +0000 (15:03 -0800)]
intel_pstate: expose turbo range to sysfs

This patch adds "turbo_pct" to the intel_pstate sysfs interface.
turbo_pct will display the percentage of the total supported
pstates that are in the turbo range.  This value is independent
of whether turbo has been disabled or not.

Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agointel_pstate: Add support for SkyLake
Kristen Carlson Accardi [Wed, 28 Jan 2015 21:53:28 +0000 (13:53 -0800)]
intel_pstate: Add support for SkyLake

Add SKL cpuid.

Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: drop unnecessary locking
Viresh Kumar [Tue, 6 Jan 2015 15:39:15 +0000 (21:09 +0530)]
cpufreq: stats: drop unnecessary locking

There is no possibility of any race on updating last_index, trans_table or
total_trans as these are updated only by cpufreq_stat_notifier_trans() which
will be called sequentially.

The only place where locking is still relevant is: cpufreq_stats_update(), which
updates time_in_state and last_time. This can be called by two thread in
parallel, that may result in races.

The two threads being:
- sysfs read of time_in_state
- and frequency transition that calls cpufreq_stat_notifier_trans().

Remove locking from the first case mentioned above.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: don't update stats on false notifiers
Viresh Kumar [Tue, 6 Jan 2015 15:39:14 +0000 (21:09 +0530)]
cpufreq: stats: don't update stats on false notifiers

We need to call cpufreq_stats_update() to update 'time_in_state' for the last
frequency. This is achieved by calling it from cpufreq_stat_notifier_trans(),
which is called after frequency transition.

But if we detect that the cpu's frequency haven't really changed and its a false
POSTCHANGE notification, we don't really need to update time_in_state.

It wouldn't cause any harm in calling cpufreq_stats_update() but we can avoid
calling it here and call it when the frequency really changes. The result will
be the same but more efficient.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: don't update stats from show_trans_table()
Viresh Kumar [Tue, 6 Jan 2015 15:39:13 +0000 (21:09 +0530)]
cpufreq: stats: don't update stats from show_trans_table()

cpufreq_stats_update() updates time_in_state and nothing else. It should ideally
be updated only in two cases:
- User requested for the current value of time_in_state.
- We have switched states and so need to update time for the last state.

Currently, we are also doing this while user asks for the transition table of
frequencies. It wouldn't do any harm, but no good as well. Its useless here.

Remove it.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: time_in_state can't be NULL in cpufreq_stats_update()
Viresh Kumar [Tue, 6 Jan 2015 15:39:12 +0000 (21:09 +0530)]
cpufreq: stats: time_in_state can't be NULL in cpufreq_stats_update()

'time_in_state' can't be NULL if 'stats' is valid. These are allocated together
and only if time_in_state is allocated successfully, we update policy->stats.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: create sysfs group once we are ready
Viresh Kumar [Tue, 6 Jan 2015 15:39:11 +0000 (21:09 +0530)]
cpufreq: stats: create sysfs group once we are ready

Userspace is free to read value of any file from cpufreq/stats directory once
they are created. __cpufreq_stats_create_table() is creating the sysfs files
first and then allocating resources for them. Though it would be quite difficult
to trigger the racy situation here, but for the sake of keeping sensible code
lets create sysfs entries only after we are ready to go.

This also does some makeup to the routine to make it look better.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: remove CPUFREQ_UPDATE_POLICY_CPU notifications
Viresh Kumar [Tue, 6 Jan 2015 15:39:10 +0000 (21:09 +0530)]
cpufreq: remove CPUFREQ_UPDATE_POLICY_CPU notifications

CPUFREQ_UPDATE_POLICY_CPU notifications were used only from cpufreq-stats which
doesn't use it anymore. Remove them.

This also decrements values of other notification macros defined after
CPUFREQ_UPDATE_POLICY_CPU by 1 to remove gaps. Hopefully all users are using
macro's instead of direct numbers and so they wouldn't break as macro values are
changed now.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: drop 'cpu' field of struct cpufreq_stats
Viresh Kumar [Tue, 6 Jan 2015 15:39:09 +0000 (21:09 +0530)]
cpufreq: stats: drop 'cpu' field of struct cpufreq_stats

'cpu' field of struct cpufreq_stats isn't used anymore and so can be dropped.
This change makes cpufreq_stats_update_policy_cpu() empty and so that is removed
as well.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: Remove (now) unused 'last_cpu' from struct cpufreq_policy
Viresh Kumar [Tue, 6 Jan 2015 15:39:08 +0000 (21:09 +0530)]
cpufreq: Remove (now) unused 'last_cpu' from struct cpufreq_policy

'last_cpu' was used only from cpufreq-stats and isn't used anymore. Get rid of
it.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: rename 'struct cpufreq_stats' objects as 'stats'
Viresh Kumar [Tue, 6 Jan 2015 15:39:07 +0000 (21:09 +0530)]
cpufreq: stats: rename 'struct cpufreq_stats' objects as 'stats'

Currently we name objects of 'struct cpufreq_stats' as 'stat' and 'stats'.
Use 'stats' to make it consistent.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: get rid of per-cpu cpufreq_stats_table
Viresh Kumar [Tue, 13 Jan 2015 06:04:00 +0000 (11:34 +0530)]
cpufreq: stats: get rid of per-cpu cpufreq_stats_table

All CPUs sharing a cpufreq policy share stats too. For this reason,
add a stats pointer to struct cpufreq_policy and drop per-CPU variable
cpufreq_stats_table used for accessing cpufreq stats so as to reduce
code complexity.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: pass 'stat' to cpufreq_stats_update()
Viresh Kumar [Tue, 6 Jan 2015 15:39:05 +0000 (21:09 +0530)]
cpufreq: stats: pass 'stat' to cpufreq_stats_update()

It is better to pass a struct cpufreq_stats pointer to cpufreq_stats_update()
instead of a CPU number, because that's all it needs.

Even if we pass a cpu number to cpufreq_stats_update(), it reads the per-cpu
variable to get 'stats' out of it. So we are doing these operations
unnecessarily:
- First getting the cpu number to pass to cpufreq_stats_update(), stat->cpu.
- And then getting stats from the cpu, per_cpu(cpufreq_stats_table, cpu).

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: don't check for freq table while freeing stats
Viresh Kumar [Tue, 6 Jan 2015 15:39:04 +0000 (21:09 +0530)]
cpufreq: stats: don't check for freq table while freeing stats

While we allocate stats, we do need to check if freq-table is present
or not as we need to use it then. But while freeing stats, all we need
to know is if stats holds a valid pointer value. There is no use of
testing if cpufreq table is present or not.

Don't check it.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: initialize 'cur_time' on its definition
Viresh Kumar [Tue, 6 Jan 2015 15:39:03 +0000 (21:09 +0530)]
cpufreq: stats: initialize 'cur_time' on its definition

'cur_time' is defined in the first line and is then assigned a value
in the next line. Initialize it while defining it.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: remove unused cpufreq_stats_attribute
Viresh Kumar [Tue, 6 Jan 2015 15:39:02 +0000 (21:09 +0530)]
cpufreq: stats: remove unused cpufreq_stats_attribute

It was never used, but is there since the first commit. Remove it.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: return -EEXIST when stats are already allocated
Viresh Kumar [Tue, 6 Jan 2015 15:39:01 +0000 (21:09 +0530)]
cpufreq: stats: return -EEXIST when stats are already allocated

__cpufreq_stats_create_table() is called from:

- cpufreq notifier on creation of a new policy. Stats will always be
  NULL here.
- cpufreq_stats_init() for all CPUs as cpufreq-stats might have been
  initialized after cpufreq driver. For any policy, 'stats' will be
  NULL for the first CPU only and will be valid for all other CPUs
  managed by the same policy.

While we return for other CPUs, we don't return the right error value.
It's not that we would fail with -EBUSY. But generally, this is what
these return values mean:
- EBUSY: we are busy right now, try again. And the retry attempt might
  be immediate.
- EEXIST: We already have what you are trying to create and there is no
  need to create it again, and so no more tries are required.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: stats: Improve module description string
Viresh Kumar [Tue, 6 Jan 2015 15:39:00 +0000 (21:09 +0530)]
cpufreq: stats: Improve module description string

The MODULE_DESCRIPTION() string is just too long and then is broken into
multiple lines just to make checkpatch happy.

Rewrite it to make it more precise.

Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: move some initialization stuff to cpufreq_policy_alloc()
Viresh Kumar [Fri, 2 Jan 2015 07:04:38 +0000 (12:34 +0530)]
cpufreq: move some initialization stuff to cpufreq_policy_alloc()

We need to initialize completion and work only on policy allocation and not
really on the policy restore side and so we better move this piece of code to
cpufreq_policy_alloc().

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: check cpufreq_policy_list instead of scanning policies for all CPUs
Viresh Kumar [Fri, 2 Jan 2015 07:04:35 +0000 (12:34 +0530)]
cpufreq: check cpufreq_policy_list instead of scanning policies for all CPUs

CPUFREQ_STICKY flag is set by drivers which don't want to get unregistered
even if cpufreq-core isn't able to initialize policy for any CPU.

When this flag isn't set, we try to unregister the driver. To find out
which CPUs are registered and which are not, we try to check per_cpu
cpufreq_cpu_data for all CPUs. Because we have a list of valid policies
available now, we better check if the list is empty or not instead of
the 'for' loop. That will be much more efficient.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: limit the scope of l_p_j variables
Viresh Kumar [Fri, 2 Jan 2015 07:04:34 +0000 (12:34 +0530)]
cpufreq: limit the scope of l_p_j variables

These variables are just used within adjust_jiffies() and so must be
local to it. Also there is no need of a dummy routine for CONFIG_SMP
case as we can take care of all that with help of macros in the same
routine. It doesn't look that ugly.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: use light-weight cpufreq_cpu_get_raw() in __cpufreq_add_dev()
Viresh Kumar [Fri, 2 Jan 2015 07:04:33 +0000 (12:34 +0530)]
cpufreq: use light-weight cpufreq_cpu_get_raw() in __cpufreq_add_dev()

We just need to check if a 'policy' is already present for the cpu we are
adding. We don't need to take all the locks and do kobject usage updates. Use
the light-weight cpufreq_cpu_get_raw() routine instead.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: get rid of 'tpolicy' from __cpufreq_add_dev()
Viresh Kumar [Fri, 2 Jan 2015 07:04:32 +0000 (12:34 +0530)]
cpufreq: get rid of 'tpolicy' from __cpufreq_add_dev()

There is no need of this separate variable, use 'policy' instead.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: get rid of CONFIG_{HOTPLUG_CPU|SMP} mess
Viresh Kumar [Fri, 2 Jan 2015 07:04:31 +0000 (12:34 +0530)]
cpufreq: get rid of CONFIG_{HOTPLUG_CPU|SMP} mess

These are messing up more than the benefit they provide. It isn't
a lot of code anyway, that we will compile without them.

Kill them.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: update driver_data->flags only if we are registering driver
Viresh Kumar [Fri, 2 Jan 2015 07:04:30 +0000 (12:34 +0530)]
cpufreq: update driver_data->flags only if we are registering driver

We should first check if a cpufreq driver is already registered or not
before updating driver_data->flags.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: pass policy to __cpufreq_get()
Viresh Kumar [Fri, 2 Jan 2015 07:04:29 +0000 (12:34 +0530)]
cpufreq: pass policy to __cpufreq_get()

There is no point finding out the 'policy' again within __cpufreq_get()
when all the callers already have it. Just make them pass policy instead.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: pass policy to cpufreq_out_of_sync
Viresh Kumar [Fri, 2 Jan 2015 07:04:28 +0000 (12:34 +0530)]
cpufreq: pass policy to cpufreq_out_of_sync

There is no point finding out the 'policy' again within cpufreq_out_of_sync()
when all the callers already have it. Just make them pass policy instead.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: No need to check for has_target()
Viresh Kumar [Fri, 2 Jan 2015 07:04:27 +0000 (12:34 +0530)]
cpufreq: No need to check for has_target()

Either we can be setpolicy or target type, nothing else. And so the
else part of setpolicy will automatically be of has_target() type.
And so we don't need to check it again.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: s/__find_governor/find_governor
Viresh Kumar [Fri, 2 Jan 2015 07:04:26 +0000 (12:34 +0530)]
cpufreq: s/__find_governor/find_governor

Remove unnecessary from find_governor's name.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: merge 'if' blocks in __cpufreq_remove_dev_prepare()
Viresh Kumar [Fri, 2 Jan 2015 07:04:25 +0000 (12:34 +0530)]
cpufreq: merge 'if' blocks in __cpufreq_remove_dev_prepare()

There are two 'if' blocks here, checking for !cpufreq_driver->setpolicy and
has_target(). Both are actually doing the same thing, merge them.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: don't need line break in show_scaling_cur_freq()
Viresh Kumar [Fri, 2 Jan 2015 07:04:24 +0000 (12:34 +0530)]
cpufreq: don't need line break in show_scaling_cur_freq()

No need of an unnecessary line break.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: remove extra parenthesis
Viresh Kumar [Fri, 2 Jan 2015 07:04:23 +0000 (12:34 +0530)]
cpufreq: remove extra parenthesis

We can live without it and so we should.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: remove dangling comment
Viresh Kumar [Fri, 2 Jan 2015 07:04:22 +0000 (12:34 +0530)]
cpufreq: remove dangling comment

It doesn't make any sense at all and is a leftover of some earlier commit.
Remove it.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: suspend cpufreq governors on shutdown
Doug Anderson [Wed, 24 Dec 2014 06:09:48 +0000 (22:09 -0800)]
cpufreq: suspend cpufreq governors on shutdown

We should stop cpufreq governors when we shut down the system.  If we
don't do this, we can end up with this deadlock:

1. cpufreq governor may be running on a CPU other than CPU0.
2. In machine_restart() we call smp_send_stop() which stops CPUs.
   If one of these CPUs was actively running a cpufreq governor
   then it may have the mutex / spinlock needed to access the main
   PMIC in the system (perhaps over I2C)
3. If a machine needs access to the main PMIC in order to shutdown
   then it will never get it since the mutex was lost when the other
   CPU stopped.
4. We'll hang (possibly eventually hitting the hard lockup detector).

Let's avoid the problem by stopping the cpufreq governor at shutdown,
which is a sensible thing to do anyway.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agocpufreq: drop owner assignment from platform_drivers
Wolfram Sang [Sun, 21 Dec 2014 21:14:26 +0000 (22:14 +0100)]
cpufreq: drop owner assignment from platform_drivers

This platform_driver does not need to set an owner, it will be
populated by the driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5 years agoLinux 3.19-rc5
Linus Torvalds [Sun, 18 Jan 2015 06:02:20 +0000 (18:02 +1200)]
Linux 3.19-rc5

5 years agoMerge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm...
Linus Torvalds [Sun, 18 Jan 2015 06:00:40 +0000 (18:00 +1200)]
Merge tag 'armsoc-for-linus' of git://git./linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "We've been sitting on our fixes branch for a while, so this batch is
  unfortunately on the large side.

  A lot of these are tweaks and fixes to device trees, fixing various
  bugs around clocks, reg ranges, etc.  There's also a few defconfig
  updates (which are on the late side, no more of those).

  All in all the diffstat is bigger than ideal at this time, but nothing
  in here seems particularly risky"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  reset: sunxi: fix spinlock initialization
  ARM: dts: disable CCI on exynos5420 based arndale-octa
  drivers: bus: check cci device tree node status
  ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
  ARM: nomadik: fix up leftover device tree pins
  ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
  ARM: at91/dt: sam9263: Add missing clocks to lcdc node
  ARM: at91: sama5d3: dt: correct the sound route
  ARM: at91/dt: sama5d4: fix the timer reg length
  ARM: exynos_defconfig: Enable LM90 driver
  ARM: exynos_defconfig: Enable options for display panel support
  arm: dts: Use pmu_system_controller phandle for dp phy
  ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
  ARM: dts: berlin: correct BG2Q's SM GPIO location.
  ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
  ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
  ARM: dts: Revert disabling of smc91x for n900
  ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
  ARM: dts: dra7-evm: fix qspi device tree partition size
  ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
  ...

5 years agoMerge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Linus Torvalds [Sun, 18 Jan 2015 03:29:11 +0000 (15:29 +1200)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux

Pull clock driver fixes from Mike Turquette:
 "Small number of fixes for clock drivers and a single null pointer
  dereference fix in the framework core code.

  The driver fixes vary from fixing section mismatch warnings to
  preventing machines from hanging (and preventing developers from
  crying)"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
  clk: fix possible null pointer dereference
  Revert "clk: ppc-corenet: Fix Section mismatch warning"
  clk: rockchip: fix deadlock possibility in cpuclk
  clk: berlin: bg2q: remove non-exist "smemc" gate clock
  clk: at91: keep slow clk enabled to prevent system hang
  clk: rockchip: fix rk3288 cpuclk core dividers
  clk: rockchip: fix rk3066 pll lock bit location
  clk: rockchip: Fix clock gate for rk3188 hclk_emem_peri
  clk: rockchip: add CLK_IGNORE_UNUSED flag to fix rk3066/rk3188 USB Host

5 years agoMerge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Linus Torvalds [Sun, 18 Jan 2015 03:26:52 +0000 (15:26 +1200)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
 "This is one fix for a Multiqueue sleeping in invalid context problem
  and a MAINTAINER file update for Qlogic"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ->queue_rq can't sleep
  MAINTAINERS: Update maintainer list for qla4xxx

5 years agoclk: fix possible null pointer dereference
Stanimir Varbanov [Mon, 5 Jan 2015 16:04:23 +0000 (18:04 +0200)]
clk: fix possible null pointer dereference

The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.

Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
5 years agoRevert "clk: ppc-corenet: Fix Section mismatch warning"
Kevin Hao [Wed, 3 Dec 2014 08:53:51 +0000 (16:53 +0800)]
Revert "clk: ppc-corenet: Fix Section mismatch warning"

This reverts commit da788acb28386aa896224e784954bb73c99ff26c.

That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.

Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
5 years agoclk: rockchip: fix deadlock possibility in cpuclk
Heiko Stübner [Fri, 16 Jan 2015 16:52:44 +0000 (17:52 +0100)]
clk: rockchip: fix deadlock possibility in cpuclk

Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.

       CPU0                    CPU1
       ----                    ----
  lock(clk_lock);
                               local_irq_disable();
                               lock(&(&i2c->lock)->rlock);
                               lock(clk_lock);
  <Interrupt>
    lock(&(&i2c->lock)->rlock);

 *** DEADLOCK ***

The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]

5 years agoMerge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Linus Torvalds [Sat, 17 Jan 2015 18:26:24 +0000 (06:26 +1200)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine fixes from Vinod Koul:
 "Two patches, the first by Andy to fix dw dmac runtime pm and second
  one by me to fix the dmaengine headers in MAINTAINERS"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: dw: balance PM runtime calls
  MAINTAINERS: dmaengine: fix the header file for dmaengine

5 years agoMerge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Sat, 17 Jan 2015 18:24:30 +0000 (06:24 +1200)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Ingo Molnar:
 "Mostly tooling fixes, but also two PMU driver fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools powerpc: Use dwfl_report_elf() instead of offline.
  perf tools: Fix segfault for symbol annotation on TUI
  perf test: Fix dwarf unwind using libunwind.
  perf tools: Avoid build splat for syscall numbers with uclibc
  perf tools: Elide strlcpy warning with uclibc
  perf tools: Fix statfs.f_type data type mismatch build error with uclibc
  tools: Remove bitops/hweight usage of bits in tools/perf
  perf machine: Fix __machine__findnew_thread() error path
  perf tools: Fix building error in x86_64 when dwarf unwind is on
  perf probe: Propagate error code when write(2) failed
  perf/x86/intel: Fix bug for "cycles:p" and "cycles:pp" on SLM
  perf/rapl: Fix sysfs_show() initialization for RAPL PMU

5 years agoMerge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git...
Ingo Molnar [Sat, 17 Jan 2015 10:04:35 +0000 (11:04 +0100)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

  - Fix segfault when using both the map symtab viewer and annotation
    in the TUI (Namhyung Kim).

  - uClibc build fixes (Alexey Brodkin, Vineet Gupta).

  - bitops/hweight were moved from tools/perf/ too tools/include, move
    some leftovers (Arnaldo Carvalho de Melo)

  - Fix dwarf unwind x86_64 build error (Namhyung Kim)

  - Fix __machine__findnew_thread() error path (Namhyung Kim)

  - Propagate error code when write(2) failed in 'perf probe' (Namhyung Kim)

  - Use dwfl_report_elf() instead of offline in powerpc bits to
    properly handle non prelinked DSOs (Sukadev Bhattiprolu).

  - Fix dwarf unwind using libunwind in 'perf test' (Wang Nan)

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
5 years agoMerge tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene...
Olof Johansson [Thu, 15 Jan 2015 23:45:18 +0000 (15:45 -0800)]
Merge tag 'samsung-fixes-3.19' of git://git./linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes for v3.19" from Kukjin Kim:

Samsung fixes for v3.19
- exynos_defconfig: enable LM90 driver and display panel support
   - HWMON
   - SENSORS_LM90
   - Direct Rendering Manager (DRM)
   - DRM bridge registration and lookup framework
   - Parade ps8622/ps8625 eDP/LVDS bridge
   - NXP ptn3460 eDP/LVDS bridge
   - Exynos Fully Interactive Mobile Display controller (FIMD)
   - Panel registration and lookup framework
   - Simple panels
   - Backlight & LCD device support

- use pmu_system_controller phandle for dp phy
  : DP PHY requires pmu_system_controller to handle PMU reg. now

* tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: exynos_defconfig: Enable LM90 driver
  ARM: exynos_defconfig: Enable options for display panel support
  arm: dts: Use pmu_system_controller phandle for dp phy

Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoreset: sunxi: fix spinlock initialization
Tyler Baker [Mon, 12 Jan 2015 15:54:46 +0000 (07:54 -0800)]
reset: sunxi: fix spinlock initialization

Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.

I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.

[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimus

Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoMerge tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel...
Olof Johansson [Tue, 13 Jan 2015 23:32:43 +0000 (15:32 -0800)]
Merge tag 'renesas-soc-fixes-for-v3.19' of git://git./linux/kernel/git/horms/renesas into fixes

Merge "Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:

Renesas ARM Based SoC Fixes for v3.19

This pull request is based on the last round of SoC updates for v3.19,
Fourth Round of Renesas ARM Based SoC Updates for v3.19, tagged as
renesas-soc3-for-v3.19, merged into your next/soc branch and included in
v3.19-rc1.

- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

  Set .control_parent for all irqpin instances for sh73a0 SoC when booting
  using legacy C.

- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

  This fixes a long standing problem which has been present since
  the sh73a0 SoC started using the INTC External IRQ pin driver.

  The patch that introduced the problem is 341eb5465f67437a ("ARM:
  shmobile: INTC External IRQ pin driver on sh73a0") which was included
  in v3.10.

* tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
  ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds

5 years agoARM: dts: disable CCI on exynos5420 based arndale-octa
Abhilash Kesavan [Sat, 10 Jan 2015 03:11:36 +0000 (08:41 +0530)]
ARM: dts: disable CCI on exynos5420 based arndale-octa

The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agodrivers: bus: check cci device tree node status
Abhilash Kesavan [Sat, 10 Jan 2015 03:11:35 +0000 (08:41 +0530)]
drivers: bus: check cci device tree node status

The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoMerge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux...
Olof Johansson [Mon, 12 Jan 2015 22:11:58 +0000 (14:11 -0800)]
Merge tag 'at91-fixes' of git://git./linux/kernel/git/nferre/linux-at91 into fixes

Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:

First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4

* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
  ARM: at91/dt: sam9263: Add missing clocks to lcdc node
  ARM: at91: sama5d3: dt: correct the sound route
  ARM: at91/dt: sama5d4: fix the timer reg length

Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
Heiko Stübner [Sun, 11 Jan 2015 22:09:23 +0000 (23:09 +0100)]
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288

rk3288 SoCs have a function to automatically switch between jtag/sdmmc pinmux
settings depending on the card state. This collides with a lot of assumptions.

It only works when using the internal card-detect mechanism and breaks
horribly when using either the normal card-detect via the slot-gpio function
or via any other pin. Also there is of course no link between the mmc and jtag
on the software-side, so the jtag clocks may very well be disabled when the
card is ejected and the soc switches back to the jtag pinmux.

Leaving the switching function enabled did result in mmc timeouts and rcu
stalls thus hanging the system on 3.19-rc1. Therefore disable it in all cases,
as we expect the devicetree to explicitly select either mmc or jtag pinmuxes
anyway.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoMerge tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux...
Olof Johansson [Sun, 11 Jan 2015 21:07:05 +0000 (13:07 -0800)]
Merge tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes

Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:

Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation

* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
  ARM: dts: berlin: correct BG2Q's SM GPIO location.
  ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
  ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host

Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoARM: nomadik: fix up leftover device tree pins
Linus Walleij [Fri, 9 Jan 2015 19:11:20 +0000 (20:11 +0100)]
ARM: nomadik: fix up leftover device tree pins

We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoMerge tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel...
Olof Johansson [Thu, 8 Jan 2015 22:43:00 +0000 (14:43 -0800)]
Merge tag 'omap-for-v3.19/fixes-rc1' of git://git./linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes against v3.19-rc1" from Tony Lindgren:

Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:

- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions

And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.

* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Revert disabling of smc91x for n900
  ARM: dts: dra7-evm: fix qspi device tree partition size
  ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
  ARM: OMAP2+: Fix n900 board name for legacy user space
  ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
  ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
  ARM: omap5/dra7xx: Fix frequency typos

Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoMerge tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo...
Olof Johansson [Thu, 8 Jan 2015 22:42:11 +0000 (14:42 -0800)]
Merge tag 'imx-fixes-3.19' of git://git./linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.19" from Shawn Guo:

The i.MX fixes for 3.19:
 - One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
   which causes system hang when accessing SPI1.
 - Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
 - Fix ULPI PHY reset modelling on imx51-babbage board to remove the
   dependency on bootloader for USB3317 ULPI PHY reset.
 - Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
   that HDMI is not working at high resolution on T0 1.0.
 - One incremental fix for CODA960 VPU enabling in device tree to
   correct interrupt order.
 - LS1021A SCFG block works in BE mode, add device tree property
   big-endian to make it right.

* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
  ARM: imx6sx: Set PLL2 as parent of QSPI clocks
  ARM: dts: imx25: Fix the SPI1 clocks
  ARM: clk-imx6q: fix video divider for rev T0 1.0
  ARM: dts: imx6qdl: Fix CODA960 interrupt order
  ARM: ls1021a: dtsi: add 'big-endian' property for scfg node

Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agoMerge tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel...
Olof Johansson [Thu, 8 Jan 2015 22:38:36 +0000 (14:38 -0800)]
Merge tag 'v3.19-rockchip-dtsfixes1' of git://git./linux/kernel/git/mmind/linux-rockchip into fixes

Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:

Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.

* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb

Signed-off-by: Olof Johansson <olof@lixom.net>
5 years agokernel: avoid overflow in cmp_range
Louis Langholtz [Fri, 16 Jan 2015 05:04:46 +0000 (22:04 -0700)]
kernel: avoid overflow in cmp_range

Avoid overflow possibility.

[ The overflow is purely theoretical, since this is used for memory
  ranges that aren't even close to using the full 64 bits, but this is
  the right thing to do regardless.  - Linus ]

Signed-off-by: Louis Langholtz <lou_langholtz@me.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Anvin <hpa@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
5 years agoperf tools powerpc: Use dwfl_report_elf() instead of offline.
Sukadev Bhattiprolu [Sat, 22 Nov 2014 01:33:53 +0000 (20:33 -0500)]
perf tools powerpc: Use dwfl_report_elf() instead of offline.

dwfl_report_offline() works only when libraries are prelinked.

Replace dwfl_report_offline() with dwfl_report_elf() so we correctly
extract debug info even from libraries that are not prelinked.

Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Link: http://lkml.kernel.org/r/20150114221045.GA17703@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf tools: Fix segfault for symbol annotation on TUI
Namhyung Kim [Wed, 14 Jan 2015 11:18:05 +0000 (20:18 +0900)]
perf tools: Fix segfault for symbol annotation on TUI

Currently the symbol structure is allocated with symbol_conf.priv_size
to carry sideband information like annotation, map browser on TUI and
sort-by-name tree node.  So retrieving these information from symbol
needs to care about the details of such placement.

However the annotation code just assumes that the symbol is placed after
the struct annotation.  But actually there's other info between them.
So accessing those struct will lead to an undefined behavior (usually a
crash) after they write their info to the same location.

To reproduce the problem, please follow the steps below:

  1. run perf report (TUI of course) with -v option
  2. open map browser (by pressing right arrow key for any entry)
  3. search any function (by pressing '/' key and input whatever..)
  4. return to the hist browser (by pressing 'q' or left arrow key)
  5. open annotation window for the same entry (by pressing 'a' key)

Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1421234288-22758-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf test: Fix dwarf unwind using libunwind.
Wang Nan [Wed, 14 Jan 2015 02:36:47 +0000 (10:36 +0800)]
perf test: Fix dwarf unwind using libunwind.

Perf tool fails to unwind user stack if the event raises in a shared
object. This patch improves tests/dwarf-unwind.c to demonstrate the
problem by utilizing commonly used glibc function "bsearch". If perf is
not statically linked, the testcase will try to unwind a mixed call
trace.

By debugging libunwind I found that there is a bug in unwind-libunwind:
it always passes 0 as segbase to libunwind, cause libunwind unable to
locate debug_frame entry fir first level ip address (I add some more
debugging output into libunwind to make things clear):

               >_Uarm_dwarf_find_debug_frame: start_ip = 10be98, end_ip = 10c2a4
               >_Uarm_dwarf_find_debug_frame: found debug_frame table `/lib/libc-2.18.so': segbase=0x0, len=7, gp=0x0, table_data=0x449388
               >_Uarm_dwarf_search_unwind_table: call lookup:ip = b6cd3bcc, segbase = 0, rel_ip = b6cd3bcc
               >lookup: e->start_ip_offset = bcf18 (rel_ip = b6cd3bcc)
               >lookup: e->start_ip_offset = 6d314 (rel_ip = b6cd3bcc)
               >lookup: e->start_ip_offset = 33d0c (rel_ip = b6cd3bcc)
                ...
               >lookup: e->start_ip_offset = 15d0c (rel_ip = b6cd3bcc)
               >lookup: e->start_ip_offset = 15c40 (rel_ip = b6cd3bcc)
 >_Uarm_dwarf_search_unwind_table: IP b6cd3bcc inside range b6c12000-b6d4c000, but no explicit unwind info found
                >put_rs_cache: unmasking signals/interrupts and releasing lock
               >_Uarm_dwarf_step: returning -10
 >_Uarm_step: dwarf_step()=-10

This patch passes map->start as segbase to dwarf_find_debug_frame(), so
di will be initialized correctly.

In addition, dso and executable are different when setting segbase. This
patch first check whether the elf is executable, and pass segbase only
for shared object.

Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1421203007-75799-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf tools: Avoid build splat for syscall numbers with uclibc
Vineet Gupta [Tue, 13 Jan 2015 13:43:22 +0000 (19:13 +0530)]
perf tools: Avoid build splat for syscall numbers with uclibc

This is due to duplicated unistd inclusion (via uClibc headers + kernel headers)
Also seen on ARM uClibc based tools

   ------- ARC build ---------->8-------------

  CC       util/evlist.o
In file included from
~/arc/k.org/arch/arc/include/uapi/asm/unistd.h:25:0,
                 from util/../perf-sys.h:10,
                 from util/../perf.h:15,
                 from util/event.h:7,
                 from util/event.c:3:
~/arc/k.org/include/uapi/asm-generic/unistd.h:906:0:
warning: "__NR_fcntl64" redefined [enabled by default]
 #define __NR_fcntl64 __NR3264_fcntl
 ^
In file included from
~/arc/gnu/INSTALL_1412-arc-2014.12-rc1/arc-snps-linux-uclibc/sysroot/usr/include/sys/syscall.h:24:0,
                 from util/../perf-sys.h:6,
   ----------------->8-------------------

   ------- ARM build ---------->8-------------

  CC FPIC  plugin_scsi.o
In file included from util/../perf-sys.h:9:0,
                 from util/../perf.h:15,
                 from util/cache.h:7,
                 from perf.c:12:
~/arc/k.org/arch/arm/include/uapi/asm/unistd.h:28:0:
warning: "__NR_restart_syscall" redefined [enabled by default]
In file included from
~/buildroot/host/usr/arm-buildroot-linux-uclibcgnueabi/sysroot/usr/include/sys/syscall.h:25:0,
                 from util/../perf-sys.h:6,
                 from util/../perf.h:15,
                 from util/cache.h:7,
                 from perf.c:12:
~/buildroot/host/usr/arm-buildroot-linux-uclibcgnueabi/sysroot/usr/include/bits/sysnum.h:17:0:
note: this is the location of the previous definition
   ----------------->8-------------------

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421156604-30603-4-git-send-email-vgupta@synopsys.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf tools: Elide strlcpy warning with uclibc
Vineet Gupta [Tue, 13 Jan 2015 13:43:21 +0000 (19:13 +0530)]
perf tools: Elide strlcpy warning with uclibc

   ----------------->8------------------
  CC       bench/sched-pipe.o
In file included from builtin-annotate.c:13:0:
util/cache.h:76:15: warning: redundant redeclaration of 'strlcpy'
[-Wredundant-decls]
 extern size_t strlcpy(char *dest, const char *src, size_t size);
               ^
In file included from util/util.h:55:0,
                 from builtin.h:4,
                 from builtin-annotate.c:8:
~/vineetg/arc/gnu/INSTALL_1412-arc-2014.12-rc1/arc-snps-linux-uclibc/sysroot/usr/include/string.h:396:15:
note: previous declaration of 'strlcpy' was here
 extern size_t strlcpy(char *__restrict dst, const char *__restrict src,
   ----------------->8------------------

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421156604-30603-3-git-send-email-vgupta@synopsys.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf tools: Fix statfs.f_type data type mismatch build error with uclibc
Alexey Brodkin [Sat, 10 Jan 2015 11:10:50 +0000 (16:40 +0530)]
perf tools: Fix statfs.f_type data type mismatch build error with uclibc

ARC Linux uses the no legacy syscalls abi and corresponding uClibc headers
statfs defines f_type to be U32 which causes perf build breakage

http://git.uclibc.org/uClibc/tree/libc/sysdeps/linux/common-generic/bits/statfs.h

  ----------->8---------------
    CC       fs/fs.o
  fs/fs.c: In function 'fs__valid_mount':
  fs/fs.c:82:24: error: comparison between signed and unsigned integer
  expressions [-Werror=sign-compare]
    else if (st_fs.f_type != magic)
                          ^
  cc1: all warnings being treated as errors
  ----------->8---------------

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Cody P Schafer <dev@codyps.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Link: http://lkml.kernel.org/r/1420888254-17504-2-git-send-email-vgupta@synopsys.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agotools: Remove bitops/hweight usage of bits in tools/perf
Arnaldo Carvalho de Melo [Tue, 13 Jan 2015 13:19:12 +0000 (10:19 -0300)]
tools: Remove bitops/hweight usage of bits in tools/perf

We need to use lib/hweight.c for that, just like we do for lib/rbtree.c,
so tools need to link hweight.o. For now do it directly, but we need to
have a tools/lib/lk.a or .so that collects these goodies...

Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-a1e91dx3apzqw5kbdt7ut21s@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf machine: Fix __machine__findnew_thread() error path
Namhyung Kim [Fri, 9 Jan 2015 00:38:12 +0000 (09:38 +0900)]
perf machine: Fix __machine__findnew_thread() error path

When thread__init_map_groups() fails, a new thread should be removed
from the rbtree since it's gonna be freed.  Also update last match cache
only if the function succeeded.

Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1420763892-15535-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf tools: Fix building error in x86_64 when dwarf unwind is on
Namhyung Kim [Mon, 12 Jan 2015 02:20:55 +0000 (10:20 +0800)]
perf tools: Fix building error in x86_64 when dwarf unwind is on

When build with 'make ARCH=x86' and dwarf unwind is on, there is a
compiling error:

   CC       /home/wn/perf/arch/x86/util/unwind-libdw.o
   CC       /home/wn/perf/arch/x86/tests/regs_load.o
 arch/x86/tests/regs_load.S: Assembler messages:
 arch/x86/tests/regs_load.S:65: Error: operand type mismatch for `push'
 arch/x86/tests/regs_load.S:72: Error: operand type mismatch for `pop'
 make[1]: *** [/home/wn/perf/arch/x86/tests/regs_load.o] Error 1
 make[1]: INTERNAL: Exiting with 25 jobserver tokens available; should be 24!
 make: *** [all] Error 2
 ...

Which is caused by incorrectly undefine macro HAVE_ARCH_X86_64_SUPPORT.
'config/Makefile.arch' tests __x86_64__ only when 'ARCH=x86_64'.
However, when building x86_64 kernel, ARCH=x86 is valid and commonly
used. Build systems, such as yocto, uses x86_64 compiler with 'ARCH=x86'
to build x86_64 perf, which causes mismatching.

As __LP64__ is defined for x86_64 as well, we can consolidate the
__x86_64__ check to the __LP64__ check and get rid of the IS_X86_64
IMHO.

(This patch is made by Namhyung Kim when replying my v1 patch:

https://lkml.org/lkml/2015/1/7/17

I modified the code to remove dependency on RAW_ARCH:

https://lkml.org/lkml/2015/1/7/865

Namhyung Kim didn't provide his SOB in his original email. I add
mine only for my modification.)

Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1421029255-23039-1-git-send-email-wangnan0@huawei.com
[ Namhyung provided his S-o-B on a followup to this patch thread on lkml ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoperf probe: Propagate error code when write(2) failed
Namhyung Kim [Sat, 10 Jan 2015 10:33:48 +0000 (19:33 +0900)]
perf probe: Propagate error code when write(2) failed

When it failed to write probe commands to the probe_event file in
debugfs, it needs to propagate the error code properly.  Current code
blindly uses the return value of the write(2) so it always uses
-1 (-EPERM) and it might confuse users.

Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1420886028-15135-4-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
5 years agoMerge tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregk...
Linus Torvalds [Fri, 16 Jan 2015 19:18:08 +0000 (08:18 +1300)]
Merge tag 'char-misc-3.19-rc5' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes from Greg KH:
 "Here are three small driver fixes for reported issues for 3.19-rc5.

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
  mei: add ABI documentation for fw_status exported through sysfs
  mei: clean reset bit before reset

5 years agoMerge tag 'driver-core-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 16 Jan 2015 19:16:52 +0000 (08:16 +1300)]
Merge tag 'driver-core-3.19-rc5' of git://git./linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is one kernfs fix for a reported issue for 3.19-rc5.

  It has been in linux-next for a while"

* tag 'driver-core-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: Fix kernfs_name_compare

5 years agoMerge tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Linus Torvalds [Fri, 16 Jan 2015 19:15:49 +0000 (08:15 +1300)]
Merge tag 'tty-3.19-rc5' of git://git./linux/kernel/git/gregkh/tty

Pull tty/serial driver fixes from Greg KH:
 "Here are some tty and serial driver fixes for 3.19-rc5 that resolve
  some reported issues, and add a new device id to the 8250 serial port
  driver.

  All have been in linux-next with no reported problems"

* tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: samsung: Add the support for Exynos5433 SoC
  Revert "tty: Fix pty master poll() after slave closes v2"
  tty: Prevent hw state corruption in exclusive mode reopen
  tty: Add support for the WCH384 4S multi-IO card
  serial: fix parisc boot hang

5 years agoMerge tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh...
Linus Torvalds [Fri, 16 Jan 2015 19:13:45 +0000 (08:13 +1300)]
Merge tag 'staging-3.19-rc5' of git://git./linux/kernel/git/gregkh/staging

Pull staging driver fixes from Greg KH:
 "Here are 6 staging driver fixes for 3.19-rc5.

  They fix some reported issues with some IIO drivers, as well as some
  issues with the vt6655 wireless driver.

  All have been in linux-next for a while"

* tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt6655: fix sparse warning: argument type
  staging: vt6655: Fix loss of distant/weak access points on channel change.
  staging: vt6655: vnt_tx_packet Fix corrupted tx packets.
  staging: vt6655: fix sparse warnings: incorrect argument type
  iio: iio: Fix iio_channel_read return if channel havn't info
  iio: ad799x: Fix ad7991/ad7995/ad7999 config setup

5 years agoMerge tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Linus Torvalds [Fri, 16 Jan 2015 19:02:44 +0000 (08:02 +1300)]
Merge tag 'usb-3.19-rc5' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here is a bunch of USB fixes for 3.19-rc5.

  Most of these are gadget driver fixes, along with the xhci driver fix
  that we both reported having problems with, as well as some new device
  ids and other tiny fixes.

  All have been in linux-next with no problems"

* tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
  usb: dwc3: gadget: Stop TRB preparation after limit is reached
  usb: dwc3: gadget: Fix TRB preparation during SG
  usb: phy: mv-usb: fix usb_phy build errors
  usb: serial: handle -ENODEV quietly in generic_submit_read_urb
  usb: serial: silence all non-critical read errors
  USB: console: fix potential use after free
  USB: console: fix uninitialised ldisc semaphore
  usb: gadget: udc: atmel: fix possible oops when unloading module
  usb: gadget: gadgetfs: fix an oops in ep_write()
  usb: phy: Fix deferred probing
  OHCI: add a quirk for ULi M5237 blocking on reset
  uas: Add US_FL_NO_ATA_1X for 2 more Seagate disk enclosures
  uas: Do not blacklist ASM1153 disk enclosures
  usb: gadget: udc: avoid dereference before NULL check in ep_queue
  usb: host: ehci-tegra: request deferred probe when failing to get phy
  uas: disable UAS on Apricorn SATA dongles
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS566 with usb-id 0bc2:a013
  uas: Add US_FL_NO_ATA_1X for Seagate devices with usb-id 0bc2:a013
  xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
  USB: EHCI: adjust error return code
  ...

5 years agoMerge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Linus Torvalds [Fri, 16 Jan 2015 19:01:21 +0000 (08:01 +1300)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Will Deacon:
 - Wire up compat_sys_execveat for compat (AArch32) tasks
 - Revert 421520ba9829, as this breaks our side of the boot protocol

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: partially revert "ARM: 8167/1: extend the reserved memory for initrd to be page aligned"
  arm64: compat: wire up compat_sys_execveat

5 years agoMerge tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Linus Torvalds [Fri, 16 Jan 2015 18:59:06 +0000 (07:59 +1300)]
Merge tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

   - Stable fix for a NFSv3/lockd race
   - Fixes for several NFSv4.1 client id trunking bugs
   - Remove an incorrect test when checking for delegated opens"

* tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: Remove incorrect check in can_open_delegated()
  NFS: Ignore transport protocol when detecting server trunking
  NFSv4/v4.1: Verify the client owner id during trunking detection
  NFSv4: Cache the NFSv4/v4.1 client owner_id in the struct nfs_client
  NFSv4.1: Fix client id trunking on Linux
  LOCKD: Fix a race when initialising nlmsvc_timeout

5 years agoMerge tag 'trace-fixes-v3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 16 Jan 2015 18:55:52 +0000 (07:55 +1300)]
Merge tag 'trace-fixes-v3.19-rc3' of git://git./linux/kernel/git/rostedt/linux-trace

Pull ftrace fixes from Steven Rostedt:
 "This holds a few fixes to the ftrace infrastructure as well as the
  mixture of function graph tracing and kprobes.

  When jprobes and function graph tracing is enabled at the same time it
  will crash the system:

      # modprobe jprobe_example
      # echo function_graph > /sys/kernel/debug/tracing/current_tracer

  After the first fork (jprobe_example probes it), the system will
  crash.

  This is due to the way jprobes copies the stack frame and does not do
  a normal function return.  This messes up with the function graph
  tracing accounting which hijacks the return address from the stack and
  replaces it with a hook function.  It saves the return addresses in a
  separate stack to put back the correct return address when done.  But
  because the jprobe functions do not do a normal return, their stack
  addresses are not put back until the function they probe is called,
  which means that the probed function will get the return address of
  the jprobe handler instead of its own.

  The simple fix here was to disable function graph tracing while the
  jprobe handler is being called.

  While debugging this I found two minor bugs with the function graph
  tracing.

  The first was about the function graph tracer sharing its function
  hash with the function tracer (they both get filtered by the same
  input).  The changing of the set_ftrace_filter would not sync the
  function recording records after a change if the function tracer was
  disabled but the function graph tracer was enabled.  This was due to
  the update only checking one of the ops instead of the shared ops to
  see if they were enabled and should perform the sync.  This caused the
  ftrace accounting to break and a ftrace_bug() would be triggered,
  disabling ftrace until a reboot.

  The second was that the check to update records only checked one of
  the filter hashes.  It needs to test both the "filter" and "notrace"
  hashes.  The "filter" hash determines what functions to trace where as
  the "notrace" hash determines what functions not to trace (trace all
  but these).  Both hashes need to be passed to the update code to find
  out what change is being done during the update.  This also broke the
  ftrace record accounting and triggered a ftrace_bug().

  This patch set also include two more fixes that were reported
  separately from the kprobe issue.

  One was that init_ftrace_syscalls() was called twice at boot up.  This
  is not a major bug, but that call performed a rather large kmalloc
  (NR_syscalls * sizeof(*syscalls_metadata)).  The second call made the
  first one a memory leak, and wastes memory.

  The other fix is a regression caused by an update in the v3.19 merge
  window.  The moving to enable events early, moved the enabling before
  PID 1 was created.  The syscall events require setting the
  TIF_SYSCALL_TRACEPOINT for all tasks.  But for_each_process_thread()
  does not include the swapper task (PID 0), and ended up being a nop.

  A suggested fix was to add the init_task() to have its flag set, but I
  didn't really want to mess with PID 0 for this minor bug.  Instead I
  disable and re-enable events again at early_initcall() where it use to
  be enabled.  This also handles any other event that might have its own
  reg function that could break at early boot up"

* tag 'trace-fixes-v3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix enabling of syscall events on the command line
  tracing: Remove extra call to init_ftrace_syscalls()
  ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing
  ftrace: Check both notrace and filter for old hash
  ftrace: Fix updating of filters for shared global_ops filters

5 years agoarm64: partially revert "ARM: 8167/1: extend the reserved memory for initrd to be...
Catalin Marinas [Fri, 16 Jan 2015 13:56:38 +0000 (13:56 +0000)]
arm64: partially revert "ARM: 8167/1: extend the reserved memory for initrd to be page aligned"

This patch partially reverts commit 421520ba98290a73b35b7644e877a48f18e06004
(only the arm64 part). There is no guarantee that the boot-loader places other
images like dtb in a different page than initrd start/end, especially when the
kernel is built with 64KB pages. When this happens, such pages must not be
freed. The free_reserved_area() already takes care of rounding up "start" and
rounding down "end" to avoid freeing partially used pages.

Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Peter Maydell <Peter.Maydell@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
5 years agoperf/x86/intel: Fix bug for "cycles:p" and "cycles:pp" on SLM
Kan Liang [Mon, 12 Jan 2015 17:42:21 +0000 (17:42 +0000)]
perf/x86/intel: Fix bug for "cycles:p" and "cycles:pp" on SLM

cycles:p and cycles:pp do not work on SLM since commit:

   86a04461a99f ("perf/x86: Revamp PEBS event selection")

UOPS_RETIRED.ALL is not a PEBS capable event, so it should not be used
to count cycle number.

Actually SLM calls intel_pebs_aliases_core2() which uses INST_RETIRED.ANY_P
to count the number of cycles. It's a PEBS capable event. But inv and
cmask must be set to count cycles.

Considering SLM allows all events as PEBS with no flags, only
INST_RETIRED.ANY_P, inv=1, cmask=16 needs to handled specially.

Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421084541-31639-1-git-send-email-kan.liang@intel.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
5 years agoperf/rapl: Fix sysfs_show() initialization for RAPL PMU
Stephane Eranian [Tue, 13 Jan 2015 22:59:53 +0000 (23:59 +0100)]
perf/rapl: Fix sysfs_show() initialization for RAPL PMU

This patch fixes a problem with the initialization of the
sysfs_show() routine for the RAPL PMU.

The current code was wrongly relying on the EVENT_ATTR_STR()
macro which uses the events_sysfs_show() function in the x86
PMU code. That function itself was relying on the x86_pmu data
structure. Yet RAPL and the core PMU (x86_pmu) have nothing to
do with each other. They should therefore not interact with
each other.

The x86_pmu structure is initialized at boot time based on
the host CPU model. When the host CPU is not supported, the
x86_pmu remains uninitialized and some of the callbacks it
contains are NULL.

The false dependency with x86_pmu could potentially cause crashes
in case the x86_pmu is not initialized while the RAPL PMU is. This
may, for instance, be the case in virtualized environments.

This patch fixes the problem by using a private sysfs_show()
routine for exporting the RAPL PMU events.

Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150113225953.GA21525@thinkpad
Cc: vincent.weaver@maine.edu
Cc: jolsa@redhat.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
5 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi...
Linus Torvalds [Fri, 16 Jan 2015 01:58:16 +0000 (14:58 +1300)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse

Pull fuse fixes from Miklos Szeredi:
 "This fixes a regression in the latest fuse update plus a fix for a
  rather theoretical memory ordering issue"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: add memory barrier to INIT
  fuse: fix LOOKUP vs INIT compat handling

5 years agoMerge tag 'fbdev-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba...
Linus Torvalds [Fri, 16 Jan 2015 01:55:47 +0000 (14:55 +1300)]
Merge tag 'fbdev-fixes-3.19' of git://git./linux/kernel/git/tomba/linux

Pull fbdev fixes from Tomi Valkeinen:
 - broadsheetfb: fix memory leak
 - simplefb: fix build failure on sparc

* tag 'fbdev-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  fbdev/broadsheetfb: fix memory leak
  simplefb: Fix build failure on Sparc

5 years agoMerge tag 'mmc-v3.19-4' of git://git.linaro.org/people/ulf.hansson/mmc
Linus Torvalds [Fri, 16 Jan 2015 01:53:07 +0000 (14:53 +1300)]
Merge tag 'mmc-v3.19-4' of git://git.linaro.org/people/ulf.hansson/mmc

Pull MMC bugfix from Ulf Hansson:
 "Fix sdhci regulator regression for Qualcomm and Nvidia boards"

* tag 'mmc-v3.19-4' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci: Set SDHCI_POWER_ON with external vmmc

5 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux...
Linus Torvalds [Fri, 16 Jan 2015 01:29:21 +0000 (14:29 +1300)]
Merge branch 'for-linus' of git://git./linux/kernel/git/geert/linux-m68k

Pull m68k fixlet from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Wire up execveat

5 years agoMerge tag 'powerpc-3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Linus Torvalds [Fri, 16 Jan 2015 01:28:01 +0000 (14:28 +1300)]
Merge tag 'powerpc-3.19-4' of git://git./linux/kernel/git/mpe/linux

Pull powerpc fixes from Michael Ellerman:
 "A few powerpc fixes"

* tag 'powerpc-3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc: Work around gcc bug in current_thread_info()
  cxl: Fix issues when unmapping contexts
  powernv: Fix OPAL tracepoint code

5 years agotracing: Fix enabling of syscall events on the command line
Steven Rostedt (Red Hat) [Wed, 14 Jan 2015 17:53:45 +0000 (12:53 -0500)]
tracing: Fix enabling of syscall events on the command line

Commit 5f893b2639b2 "tracing: Move enabling tracepoints to just after
rcu_init()" broke the enabling of system call events from the command
line. The reason was that the enabling of command line trace events
was moved before PID 1 started, and the syscall tracepoints require
that all tasks have the TIF_SYSCALL_TRACEPOINT flag set. But the
swapper task (pid 0) is not part of that. Since the swapper task is the
only task that is running at this early in boot, no task gets the
flag set, and the tracepoint never gets reached.

Instead of setting the swapper task flag (there should be no reason to
do that), re-enabled trace events again after the init thread (PID 1)
has been started. It requires disabling all command line events and
re-enabling them, as just enabling them again will not reset the logic
to set the TIF_SYSCALL_TRACEPOINT flag, as the syscall tracepoint will
be fooled into thinking that it was already set, and wont try setting
it again. For this reason, we must first disable it and re-enable it.

Link: http://lkml.kernel.org/r/1421188517-18312-1-git-send-email-mpe@ellerman.id.au
Link: http://lkml.kernel.org/r/20150115040506.216066449@goodmis.org
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
5 years agotracing: Remove extra call to init_ftrace_syscalls()
Steven Rostedt (Red Hat) [Wed, 14 Jan 2015 17:24:37 +0000 (12:24 -0500)]
tracing: Remove extra call to init_ftrace_syscalls()

trace_init() calls init_ftrace_syscalls() and then calls trace_event_init()
which also calls init_ftrace_syscalls(). It makes more sense to only
call it from trace_event_init().

Calling it twice wastes memory, as it allocates the syscall events twice,
and loses the first copy of it.

Link: http://lkml.kernel.org/r/54AF53BD.5070303@huawei.com
Link: http://lkml.kernel.org/r/20150115040505.930398632@goodmis.org
Reported-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
5 years agoftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing
Steven Rostedt (Red Hat) [Mon, 12 Jan 2015 17:12:03 +0000 (12:12 -0500)]
ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing

If the function graph tracer traces a jprobe callback, the system will
crash. This can easily be demonstrated by compiling the jprobe
sample module that is in the kernel tree, loading it and running the
function graph tracer.

 # modprobe jprobe_example.ko
 # echo function_graph > /sys/kernel/debug/tracing/current_tracer
 # ls

The first two commands end up in a nice crash after the first fork.
(do_fork has a jprobe attached to it, so "ls" just triggers that fork)

The problem is caused by the jprobe_return() that all jprobe callbacks
must end with. The way jprobes works is that the function a jprobe
is attached to has a breakpoint placed at the start of it (or it uses
ftrace if fentry is supported). The breakpoint handler (or ftrace callback)
will copy the stack frame and change the ip address to return to the
jprobe handler instead of the function. The jprobe handler must end
with jprobe_return() which swaps the stack and does an int3 (breakpoint).
This breakpoint handler will then put back the saved stack frame,
simulate the instruction at the beginning of the function it added
a breakpoint to, and then continue on.

For function tracing to work, it hijakes the return address from the
stack frame, and replaces it with a hook function that will trace
the end of the call. This hook function will restore the return
address of the function call.

If the function tracer traces the jprobe handler, the hook function
for that handler will not be called, and its saved return address
will be used for the next function. This will result in a kernel crash.

To solve this, pause function tracing before the jprobe handler is called
and unpause it before it returns back to the function it probed.

Some other updates:

Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the
code look a bit cleaner and easier to understand (various tries to fix
this bug required this change).

Note, if fentry is being used, jprobes will change the ip address before
the function graph tracer runs and it will not be able to trace the
function that the jprobe is probing.

Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.org
Cc: stable@vger.kernel.org # 2.6.30+
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
5 years agoftrace: Check both notrace and filter for old hash
Steven Rostedt (Red Hat) [Tue, 13 Jan 2015 19:03:38 +0000 (14:03 -0500)]
ftrace: Check both notrace and filter for old hash

Using just the filter for checking for trampolines or regs is not enough
when updating the code against the records that represent all functions.
Both the filter hash and the notrace hash need to be checked.

To trigger this bug (using trace-cmd and perf):

 # perf probe -a do_fork
 # trace-cmd start -B foo -e probe
 # trace-cmd record -p function_graph -n do_fork sleep 1

The trace-cmd record at the end clears the filter before it disables
function_graph tracing and then that causes the accounting of the
ftrace function records to become incorrect and causes ftrace to bug.

Link: http://lkml.kernel.org/r/20150114154329.358378039@goodmis.org
Cc: stable@vger.kernel.org
[ still need to switch old_hash_ops to old_ops_hash ]
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
5 years agoftrace: Fix updating of filters for shared global_ops filters
Steven Rostedt (Red Hat) [Tue, 13 Jan 2015 16:20:43 +0000 (11:20 -0500)]
ftrace: Fix updating of filters for shared global_ops filters

As the set_ftrace_filter affects both the function tracer as well as the
function graph tracer, the ops that represent each have a shared
ftrace_ops_hash structure. This allows both to be updated when the filter
files are updated.

But if function graph is enabled and the global_ops (function tracing) ops
is not, then it is possible that the filter could be changed without the
update happening for the function graph ops. This will cause the changes
to not take place and may even cause a ftrace_bug to occur as it could mess
with the trampoline accounting.

The solution is to check if the ops uses the shared global_ops filter and
if the ops itself is not enabled, to check if there's another ops that is
enabled and also shares the global_ops filter. In that case, the
modification still needs to be executed.

Link: http://lkml.kernel.org/r/20150114154329.055980438@goodmis.org
Cc: stable@vger.kernel.org # 3.17+
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>