* everything but the rate is checked here, the rate check is done
* separately to avoid doing two lookups for a rate for each frame.
*/
- if (!ath9k_cmn_rx_accept(common, hdr, rx_status, rx_stats, decrypt_error, sc->rx.rxfilter)) {
- ret = -EINVAL;
- goto exit;
- }
- if (!ath9k_rx_accept(common, hdr, rx_status, rx_stats, decrypt_error))
++ if (!ath9k_cmn_rx_accept(common, hdr, rx_status, rx_stats, decrypt_error, sc->rx.rxfilter))
+ return -EINVAL;
if (ath_is_mybeacon(common, hdr)) {
RX_STAT_INC(rx_beacons);
/*
* This shouldn't happen, but have a safety check anyway.
*/
- if (WARN_ON(!ah->curchan)) {
- ret = -EINVAL;
- goto exit;
- }
+ if (WARN_ON(!ah->curchan))
+ return -EINVAL;
- if (ath9k_process_rate(common, hw, rx_stats, rx_status))
+ if (ath9k_cmn_process_rate(common, hw, rx_stats, rx_status)) {
+ /*
+ * No valid hardware bitrate found -- we should not get here
+ * because hardware has already validated this frame as OK.
+ */
+ ath_dbg(common, ANY, "unsupported hw bitrate detected 0x%02x using 1 Mbit\n",
+ rx_stats->rs_rate);
+ RX_STAT_INC(rx_rate_err);
- ret =-EINVAL;
- goto exit;
+ return -EINVAL;
+ }
- ath9k_process_rssi(common, hw, rx_stats, rx_status);
+ ath9k_cmn_process_rssi(common, hw, rx_stats, rx_status);
rx_status->band = ah->curchan->chan->band;
rx_status->freq = ah->curchan->chan->center_freq;
sc->rx.num_pkts++;
#endif
- exit:
- sc->rx.discard_next = false;
- return ret;
+ return 0;
+
+ corrupt:
+ sc->rx.discard_next = rx_stats->rs_more;
+ return -EINVAL;
}
-static void ath9k_rx_skb_postprocess(struct ath_common *common,
- struct sk_buff *skb,
- struct ath_rx_status *rx_stats,
- struct ieee80211_rx_status *rxs,
- bool decrypt_error)
-{
- struct ath_hw *ah = common->ah;
- struct ieee80211_hdr *hdr;
- int hdrlen, padpos, padsize;
- u8 keyix;
- __le16 fc;
-
- /* see if any padding is done by the hw and remove it */
- hdr = (struct ieee80211_hdr *) skb->data;
- hdrlen = ieee80211_get_hdrlen_from_skb(skb);
- fc = hdr->frame_control;
- padpos = ieee80211_hdrlen(fc);
-
- /* The MAC header is padded to have 32-bit boundary if the
- * packet payload is non-zero. The general calculation for
- * padsize would take into account odd header lengths:
- * padsize = (4 - padpos % 4) % 4; However, since only
- * even-length headers are used, padding can only be 0 or 2
- * bytes and we can optimize this a bit. In addition, we must
- * not try to remove padding from short control frames that do
- * not have payload. */
- padsize = padpos & 3;
- if (padsize && skb->len>=padpos+padsize+FCS_LEN) {
- memmove(skb->data + padsize, skb->data, padpos);
- skb_pull(skb, padsize);
- }
-
- keyix = rx_stats->rs_keyix;
-
- if (!(keyix == ATH9K_RXKEYIX_INVALID) && !decrypt_error &&
- ieee80211_has_protected(fc)) {
- rxs->flag |= RX_FLAG_DECRYPTED;
- } else if (ieee80211_has_protected(fc)
- && !decrypt_error && skb->len >= hdrlen + 4) {
- keyix = skb->data[hdrlen + 3] >> 6;
-
- if (test_bit(keyix, common->keymap))
- rxs->flag |= RX_FLAG_DECRYPTED;
- }
- if (ah->sw_mgmt_crypto &&
- (rxs->flag & RX_FLAG_DECRYPTED) &&
- ieee80211_is_mgmt(fc))
- /* Use software decrypt for management frames. */
- rxs->flag &= ~RX_FLAG_DECRYPTED;
-}
-
/*
* Run the LNA combining algorithm only in these cases:
*
projects / linux-drm-fsl-dcu.git / commitdiff