#
# Makefile for the PowerPC 85xx linux kernel.
#
-obj-$(CONFIG_PPC_85xx) += misc.o mpc85xx_ads.o
+obj-$(CONFIG_PPC_85xx) += misc.o pci.o
+obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
#define PIRQC MPC85xx_IRQ_EXT3
#define PIRQD MPC85xx_IRQ_EXT4
-#define MPC85XX_PCI1_LOWER_IO 0x00000000
-#define MPC85XX_PCI1_UPPER_IO 0x00ffffff
-
-#define MPC85XX_PCI1_LOWER_MEM 0x80000000
-#define MPC85XX_PCI1_UPPER_MEM 0x9fffffff
-
-#define MPC85XX_PCI1_IO_BASE 0xe2000000
-#define MPC85XX_PCI1_MEM_OFFSET 0x00000000
-
-#define MPC85XX_PCI1_IO_SIZE 0x01000000
-
-/* PCI config */
-#define PCI1_CFG_ADDR_OFFSET (0x8000)
-#define PCI1_CFG_DATA_OFFSET (0x8004)
-
-#define PCI2_CFG_ADDR_OFFSET (0x9000)
-#define PCI2_CFG_DATA_OFFSET (0x9004)
-
-/* Additional register for PCI-X configuration */
-#define PCIX_NEXT_CAP 0x60
-#define PCIX_CAP_ID 0x61
-#define PCIX_COMMAND 0x62
-#define PCIX_STATUS 0x64
-
/* Offset of CPM register space */
#define CPM_MAP_ADDR (CCSRBAR + MPC85xx_CPM_OFFSET)
*/
extern void mpc85xx_restart(char *);
+extern int add_bridge(struct device_node *dev);
0x0, /* External 11: */
};
+#ifdef CONFIG_PCI
+/*
+ * interrupt routing
+ */
+
+int
+mpc85xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
+{
+ static char pci_irq_table[][4] =
+ /*
+ * This is little evil, but works around the fact
+ * that revA boards have IDSEL starting at 18
+ * and others boards (older) start at 12
+ *
+ * PCI IDSEL/INTPIN->INTLINE
+ * A B C D
+ */
+ {
+ {PIRQA, PIRQB, PIRQC, PIRQD}, /* IDSEL 2 */
+ {PIRQD, PIRQA, PIRQB, PIRQC},
+ {PIRQC, PIRQD, PIRQA, PIRQB},
+ {PIRQB, PIRQC, PIRQD, PIRQA}, /* IDSEL 5 */
+ {0, 0, 0, 0}, /* -- */
+ {0, 0, 0, 0}, /* -- */
+ {0, 0, 0, 0}, /* -- */
+ {0, 0, 0, 0}, /* -- */
+ {0, 0, 0, 0}, /* -- */
+ {0, 0, 0, 0}, /* -- */
+ {PIRQA, PIRQB, PIRQC, PIRQD}, /* IDSEL 12 */
+ {PIRQD, PIRQA, PIRQB, PIRQC},
+ {PIRQC, PIRQD, PIRQA, PIRQB},
+ {PIRQB, PIRQC, PIRQD, PIRQA}, /* IDSEL 15 */
+ {0, 0, 0, 0}, /* -- */
+ {0, 0, 0, 0}, /* -- */
+ {PIRQA, PIRQB, PIRQC, PIRQD}, /* IDSEL 18 */
+ {PIRQD, PIRQA, PIRQB, PIRQC},
+ {PIRQC, PIRQD, PIRQA, PIRQB},
+ {PIRQB, PIRQC, PIRQD, PIRQA}, /* IDSEL 21 */
+ };
+
+ const long min_idsel = 2, max_idsel = 21, irqs_per_slot = 4;
+ return PCI_IRQ_TABLE_LOOKUP;
+}
+
+int
+mpc85xx_exclude_device(u_char bus, u_char devfn)
+{
+ if (bus == 0 && PCI_SLOT(devfn) == 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ else
+ return PCIBIOS_SUCCESSFUL;
+}
+
+#endif /* CONFIG_PCI */
+
+
void __init mpc85xx_ads_pic_init(void)
{
struct mpic *mpic1;
static void __init mpc85xx_ads_setup_arch(void)
{
struct device_node *cpu;
+ struct device_node *np;
if (ppc_md.progress)
ppc_md.progress("mpc85xx_ads_setup_arch()", 0);
loops_per_jiffy = 50000000 / HZ;
of_node_put(cpu);
}
+
+#ifdef CONFIG_PCI
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+ add_bridge(np);
+
+ ppc_md.pci_swizzle = common_swizzle;
+ ppc_md.pci_map_irq = mpc85xx_map_irq;
+ ppc_md.pci_exclude_device = mpc85xx_exclude_device;
+#endif
+
#ifdef CONFIG_ROOT_NFS
ROOT_DEV = Root_NFS;
#else
--- /dev/null
+/*
+ * FSL SoC setup code
+ *
+ * Maintained by Kumar Gala (see MAINTAINERS for contact information)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+
+#include <asm/system.h>
+#include <asm/atomic.h>
+#include <asm/io.h>
+#include <asm/pci-bridge.h>
+#include <asm/prom.h>
+#include <sysdev/fsl_soc.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(x...) printk(x)
+#else
+#define DBG(x...)
+#endif
+
+int mpc85xx_pci2_busno = 0;
+
+#ifdef CONFIG_PCI
+int __init add_bridge(struct device_node *dev)
+{
+ int len;
+ struct pci_controller *hose;
+ struct resource rsrc;
+ int *bus_range;
+ int primary = 1, has_address = 0;
+ phys_addr_t immr = get_immrbase();
+
+ DBG("Adding PCI host bridge %s\n", dev->full_name);
+
+ /* Fetch host bridge registers address */
+ has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
+
+ /* Get bus range if any */
+ bus_range = (int *) get_property(dev, "bus-range", &len);
+ if (bus_range == NULL || len < 2 * sizeof(int)) {
+ printk(KERN_WARNING "Can't get bus-range for %s, assume"
+ " bus 0\n", dev->full_name);
+ }
+
+ hose = pcibios_alloc_controller();
+ if (!hose)
+ return -ENOMEM;
+ hose->arch_data = dev;
+ hose->set_cfg_type = 1;
+
+ hose->first_busno = bus_range ? bus_range[0] : 0;
+ hose->last_busno = bus_range ? bus_range[1] : 0xff;
+
+ /* PCI 1 */
+ if ((rsrc.start & 0xfffff) == 0x8000) {
+ setup_indirect_pci(hose, immr + 0x8000, immr + 0x8004);
+ }
+ /* PCI 2 */
+ if ((rsrc.start & 0xfffff) == 0x9000) {
+ setup_indirect_pci(hose, immr + 0x9000, immr + 0x9004);
+ primary = 0;
+ hose->bus_offset = hose->first_busno;
+ mpc85xx_pci2_busno = hose->first_busno;
+ }
+
+ printk(KERN_INFO "Found MPC85xx PCI host bridge at 0x%08lx. "
+ "Firmware bus number: %d->%d\n",
+ rsrc.start, hose->first_busno, hose->last_busno);
+
+ DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
+ hose, hose->cfg_addr, hose->cfg_data);
+
+ /* Interpret the "ranges" property */
+ /* This also maps the I/O region and sets isa_io/mem_base */
+ pci_process_bridge_OF_ranges(hose, dev, primary);
+
+ return 0;
+}
+
+#endif
projects / linux-drm-fsl-dcu.git / commitdiff