#define DRV_VERSION "2.0"
enum {
+ K2_FLAG_NO_ATAPI_DMA = (1 << 29),
+
/* Taskfile registers offsets */
K2_SATA_TF_CMD_OFFSET = 0x00,
K2_SATA_TF_DATA_OFFSET = 0x00,
/* Port stride */
K2_SATA_PORT_OFFSET = 0x100,
+
+ board_svw4 = 0,
+ board_svw8 = 1,
+};
+
+static const struct k2_board_info {
+ unsigned int n_ports;
+ unsigned long port_flags;
+} k2_board_info[] = {
+ /* board_svw4 */
+ { 4, K2_FLAG_NO_ATAPI_DMA },
+
+ /* board_svw8 */
+ { 8, K2_FLAG_NO_ATAPI_DMA },
};
static u8 k2_stat_check_status(struct ata_port *ap);
+static int k2_sata_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ if (qc->ap->flags & K2_FLAG_NO_ATAPI_DMA)
+ return -1; /* ATAPI DMA not supported */
+
+ return 0;
+}
+
static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL)
return 0xffffffffU;
- return readl((void *) ap->ioaddr.scr_addr + (sc_reg * 4));
+ return readl((void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
}
{
if (sc_reg > SCR_CONTROL)
return;
- writel(val, (void *) ap->ioaddr.scr_addr + (sc_reg * 4));
+ writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
}
ata_wait_idle(ap);
}
if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
- writew(tf->feature | (((u16)tf->hob_feature) << 8), ioaddr->feature_addr);
- writew(tf->nsect | (((u16)tf->hob_nsect) << 8), ioaddr->nsect_addr);
- writew(tf->lbal | (((u16)tf->hob_lbal) << 8), ioaddr->lbal_addr);
- writew(tf->lbam | (((u16)tf->hob_lbam) << 8), ioaddr->lbam_addr);
- writew(tf->lbah | (((u16)tf->hob_lbah) << 8), ioaddr->lbah_addr);
+ writew(tf->feature | (((u16)tf->hob_feature) << 8),
+ ioaddr->feature_addr);
+ writew(tf->nsect | (((u16)tf->hob_nsect) << 8),
+ ioaddr->nsect_addr);
+ writew(tf->lbal | (((u16)tf->hob_lbal) << 8),
+ ioaddr->lbal_addr);
+ writew(tf->lbam | (((u16)tf->hob_lbam) << 8),
+ ioaddr->lbam_addr);
+ writew(tf->lbah | (((u16)tf->hob_lbah) << 8),
+ ioaddr->lbah_addr);
} else if (is_addr) {
writew(tf->feature, ioaddr->feature_addr);
writew(tf->nsect, ioaddr->nsect_addr);
struct ata_port *ap = qc->ap;
unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
u8 dmactl;
- void *mmio = (void *) ap->ioaddr.bmdma_addr;
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
/* load PRD table addr. */
mb(); /* make sure PRD table writes are visible to controller */
writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS);
static void k2_bmdma_start_mmio (struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
- void *mmio = (void *) ap->ioaddr.bmdma_addr;
+ void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
u8 dmactl;
/* start host DMA transaction */
static u8 k2_stat_check_status(struct ata_port *ap)
{
- return readl((void *) ap->ioaddr.status_addr);
+ return readl((void __iomem *) ap->ioaddr.status_addr);
}
#ifdef CONFIG_PPC_OF
.check_status = k2_stat_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .check_atapi_dma = k2_sata_check_atapi_dma,
.bmdma_setup = k2_bmdma_setup_mmio,
.bmdma_start = k2_bmdma_start_mmio,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_mmio_data_xfer,
+ .data_xfer = ata_data_xfer,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.scr_read = k2_sata_scr_read,
.scr_write = k2_sata_scr_write,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_pci_host_stop,
};
-static void k2_sata_setup_port(struct ata_ioports *port, unsigned long base)
+static void k2_sata_setup_port(struct ata_ioports *port, void __iomem *base)
{
port->cmd_addr = base + K2_SATA_TF_CMD_OFFSET;
port->data_addr = base + K2_SATA_TF_DATA_OFFSET;
static int k2_sata_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- struct ata_probe_ent *probe_ent = NULL;
- unsigned long base;
+ struct device *dev = &pdev->dev;
+ struct ata_probe_ent *probe_ent;
void __iomem *mmio_base;
- int pci_dev_busy = 0;
+ const struct k2_board_info *board_info =
+ &k2_board_info[ent->driver_data];
int rc;
int i;
* If this driver happens to only be useful on Apple's K2, then
* we should check that here as it has a normal Serverworks ID
*/
- rc = pci_enable_device(pdev);
+ rc = pcim_enable_device(pdev);
if (rc)
return rc;
/*
if (pci_resource_len(pdev, 5) == 0)
return -ENODEV;
- /* Request PCI regions */
- rc = pci_request_regions(pdev, DRV_NAME);
- if (rc) {
- pci_dev_busy = 1;
- goto err_out;
- }
+ /* Request and iomap PCI regions */
+ rc = pcim_iomap_regions(pdev, 1 << 5, DRV_NAME);
+ if (rc == -EBUSY)
+ pcim_pin_device(pdev);
+ if (rc)
+ return rc;
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
- goto err_out_regions;
+ return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
- goto err_out_regions;
+ return rc;
- probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
- if (probe_ent == NULL) {
- rc = -ENOMEM;
- goto err_out_regions;
- }
+ probe_ent = devm_kzalloc(dev, sizeof(*probe_ent), GFP_KERNEL);
+ if (probe_ent == NULL)
+ return -ENOMEM;
- memset(probe_ent, 0, sizeof(*probe_ent));
probe_ent->dev = pci_dev_to_dev(pdev);
INIT_LIST_HEAD(&probe_ent->node);
- mmio_base = pci_iomap(pdev, 5, 0);
- if (mmio_base == NULL) {
- rc = -ENOMEM;
- goto err_out_free_ent;
- }
- base = (unsigned long) mmio_base;
-
- /* Clear a magic bit in SCR1 according to Darwin, those help
- * some funky seagate drives (though so far, those were already
- * set by the firmware on the machines I had access to)
- */
- writel(readl(mmio_base + K2_SATA_SICR1_OFFSET) & ~0x00040000,
- mmio_base + K2_SATA_SICR1_OFFSET);
-
- /* Clear SATA error & interrupts we don't use */
- writel(0xffffffff, mmio_base + K2_SATA_SCR_ERROR_OFFSET);
- writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
-
probe_ent->sht = &k2_sata_sht;
probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO;
+ ATA_FLAG_MMIO | board_info->port_flags;
probe_ent->port_ops = &k2_sata_ops;
probe_ent->n_ports = 4;
probe_ent->irq = pdev->irq;
probe_ent->irq_flags = IRQF_SHARED;
- probe_ent->mmio_base = mmio_base;
+ probe_ent->iomap = pcim_iomap_table(pdev);
/* We don't care much about the PIO/UDMA masks, but the core won't like us
* if we don't fill these
probe_ent->mwdma_mask = 0x7;
probe_ent->udma_mask = 0x7f;
+ mmio_base = probe_ent->iomap[5];
+
/* different controllers have different number of ports - currently 4 or 8 */
/* All ports are on the same function. Multi-function device is no
* longer available. This should not be seen in any system. */
- for (i = 0; i < ent->driver_data; i++)
- k2_sata_setup_port(&probe_ent->port[i], base + i * K2_SATA_PORT_OFFSET);
+ for (i = 0; i < board_info->n_ports; i++)
+ k2_sata_setup_port(&probe_ent->port[i],
+ mmio_base + i * K2_SATA_PORT_OFFSET);
+
+ /* Clear a magic bit in SCR1 according to Darwin, those help
+ * some funky seagate drives (though so far, those were already
+ * set by the firmware on the machines I had access to)
+ */
+ writel(readl(mmio_base + K2_SATA_SICR1_OFFSET) & ~0x00040000,
+ mmio_base + K2_SATA_SICR1_OFFSET);
+
+ /* Clear SATA error & interrupts we don't use */
+ writel(0xffffffff, mmio_base + K2_SATA_SCR_ERROR_OFFSET);
+ writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
pci_set_master(pdev);
- /* FIXME: check ata_device_add return value */
- ata_device_add(probe_ent);
- kfree(probe_ent);
+ if (!ata_device_add(probe_ent))
+ return -ENODEV;
+ devm_kfree(dev, probe_ent);
return 0;
-
-err_out_free_ent:
- kfree(probe_ent);
-err_out_regions:
- pci_release_regions(pdev);
-err_out:
- if (!pci_dev_busy)
- pci_disable_device(pdev);
- return rc;
}
/* 0x240 is device ID for Apple K2 device
* controller
* */
static const struct pci_device_id k2_sata_pci_tbl[] = {
- { 0x1166, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { 0x1166, 0x0241, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { 0x1166, 0x0242, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
- { 0x1166, 0x024a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
- { 0x1166, 0x024b, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0240), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0241), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0242), board_svw8 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024a), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024b), board_svw4 },
+
{ }
};
-
static struct pci_driver k2_sata_pci_driver = {
.name = DRV_NAME,
.id_table = k2_sata_pci_tbl,
.remove = ata_pci_remove_one,
};
-
static int __init k2_sata_init(void)
{
return pci_register_driver(&k2_sata_pci_driver);
}
-
static void __exit k2_sata_exit(void)
{
pci_unregister_driver(&k2_sata_pci_driver);
}
-
MODULE_AUTHOR("Benjamin Herrenschmidt");
MODULE_DESCRIPTION("low-level driver for K2 SATA controller");
MODULE_LICENSE("GPL");
projects / linux-drm-fsl-dcu.git / blobdiff