static int ht6560a; /* HT 6560A on primary 1, secondary 2, both 3 */
static int ht6560b; /* HT 6560A on primary 1, secondary 2, both 3 */
static int opti82c611a; /* Opti82c611A on primary 1, secondary 2, both 3 */
-static int opti82c46x; /* Opti 82c465MV present (pri/sec autodetect) */
+static int opti82c46x; /* Opti 82c465MV present (pri/sec autodetect) */
static int autospeed; /* Chip present which snoops speed changes */
static int pio_mask = 0x1F; /* PIO range for autospeed devices */
+static int iordy_mask = 0xFFFFFFFF; /* Use iordy if available */
/**
* legacy_set_mode - mode setting
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
if (ata_dev_enabled(dev)) {
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO\n");
dev->pio_mode = XFER_PIO_0;
dev->xfer_mode = XFER_PIO_0;
dev->xfer_shift = ATA_SHIFT_PIO;
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer_noirq,
+ .data_xfer = ata_data_xfer_noirq,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
static struct ata_port_operations legacy_port_ops = {
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer_noirq,
+ .data_xfer = ata_data_xfer_noirq,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
/*
local_irq_save(flags);
/* Perform the 32bit I/O synchronization sequence */
- inb(ap->ioaddr.nsect_addr);
- inb(ap->ioaddr.nsect_addr);
- inb(ap->ioaddr.nsect_addr);
+ ioread8(ap->ioaddr.nsect_addr);
+ ioread8(ap->ioaddr.nsect_addr);
+ ioread8(ap->ioaddr.nsect_addr);
/* Now the data */
if (write_data)
- outsl(ap->ioaddr.data_addr, buf, buflen >> 2);
+ iowrite32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
else
- insl(ap->ioaddr.data_addr, buf, buflen >> 2);
+ ioread32_rep(ap->ioaddr.data_addr, buf, buflen >> 2);
if (unlikely(slop)) {
u32 pad;
if (write_data) {
memcpy(&pad, buf + buflen - slop, slop);
- outl(le32_to_cpu(pad), ap->ioaddr.data_addr);
+ pad = le32_to_cpu(pad);
+ iowrite32(pad, ap->ioaddr.data_addr);
} else {
- pad = cpu_to_le16(inl(ap->ioaddr.data_addr));
+ pad = ioread32(ap->ioaddr.data_addr);
+ pad = cpu_to_le16(pad);
memcpy(buf + buflen - slop, &pad, slop);
}
}
local_irq_restore(flags);
}
else
- ata_pio_data_xfer_noirq(adev, buf, buflen, write_data);
+ ata_data_xfer_noirq(adev, buf, buflen, write_data);
}
static struct ata_port_operations pdc20230_port_ops = {
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
/*
inb(0x3E6);
inb(0x3E6);
- outb(recover << 4 | active, ap->ioaddr.device_addr);
- inb(ap->ioaddr.status_addr);
+ iowrite8(recover << 4 | active, ap->ioaddr.device_addr);
+ ioread8(ap->ioaddr.status_addr);
}
static struct ata_port_operations ht6560a_port_ops = {
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer, /* Check vlb/noirq */
+ .data_xfer = ata_data_xfer, /* Check vlb/noirq */
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
/*
inb(0x3E6);
inb(0x3E6);
- outb(recover << 4 | active, ap->ioaddr.device_addr);
+ iowrite8(recover << 4 | active, ap->ioaddr.device_addr);
if (adev->class != ATA_DEV_ATA) {
u8 rconf = inb(0x3E6);
outb(rconf, 0x3E6);
}
}
- inb(ap->ioaddr.status_addr);
+ ioread8(ap->ioaddr.status_addr);
}
static struct ata_port_operations ht6560b_port_ops = {
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer, /* FIXME: Check 32bit and noirq */
+ .data_xfer = ata_data_xfer, /* FIXME: Check 32bit and noirq */
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
/*
u8 rc;
/* Enter configuration mode */
- inw(ap->ioaddr.error_addr);
- inw(ap->ioaddr.error_addr);
- outb(3, ap->ioaddr.nsect_addr);
+ ioread16(ap->ioaddr.error_addr);
+ ioread16(ap->ioaddr.error_addr);
+ iowrite8(3, ap->ioaddr.nsect_addr);
/* Read VLB clock strapping */
- clock = 1000000000 / khz[inb(ap->ioaddr.lbah_addr) & 0x03];
+ clock = 1000000000 / khz[ioread8(ap->ioaddr.lbah_addr) & 0x03];
/* Get the timing data in cycles */
ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000);
setup = FIT(t.setup, 1, 4) - 1;
/* Select the right timing bank for write timing */
- rc = inb(ap->ioaddr.lbal_addr);
+ rc = ioread8(ap->ioaddr.lbal_addr);
rc &= 0x7F;
rc |= (adev->devno << 7);
- outb(rc, ap->ioaddr.lbal_addr);
+ iowrite8(rc, ap->ioaddr.lbal_addr);
/* Write the timings */
- outb(active << 4 | recover, ap->ioaddr.error_addr);
+ iowrite8(active << 4 | recover, ap->ioaddr.error_addr);
/* Select the right bank for read timings, also
load the shared timings for address */
- rc = inb(ap->ioaddr.device_addr);
+ rc = ioread8(ap->ioaddr.device_addr);
rc &= 0xC0;
rc |= adev->devno; /* Index select */
rc |= (setup << 4) | 0x04;
- outb(rc, ap->ioaddr.device_addr);
+ iowrite8(rc, ap->ioaddr.device_addr);
/* Load the read timings */
- outb(active << 4 | recover, ap->ioaddr.data_addr);
+ iowrite8(active << 4 | recover, ap->ioaddr.data_addr);
/* Ensure the timing register mode is right */
- rc = inb (ap->ioaddr.lbal_addr);
+ rc = ioread8(ap->ioaddr.lbal_addr);
rc &= 0x73;
rc |= 0x84;
- outb(rc, ap->ioaddr.lbal_addr);
+ iowrite8(rc, ap->ioaddr.lbal_addr);
/* Exit command mode */
- outb(0x83, ap->ioaddr.nsect_addr);
+ iowrite8(0x83, ap->ioaddr.nsect_addr);
}
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
/*
sysclk = opti_syscfg(0xAC) & 0xC0; /* BIOS set */
/* Enter configuration mode */
- inw(ap->ioaddr.error_addr);
- inw(ap->ioaddr.error_addr);
- outb(3, ap->ioaddr.nsect_addr);
+ ioread16(ap->ioaddr.error_addr);
+ ioread16(ap->ioaddr.error_addr);
+ iowrite8(3, ap->ioaddr.nsect_addr);
/* Read VLB clock strapping */
clock = 1000000000 / khz[sysclk];
setup = FIT(t.setup, 1, 4) - 1;
/* Select the right timing bank for write timing */
- rc = inb(ap->ioaddr.lbal_addr);
+ rc = ioread8(ap->ioaddr.lbal_addr);
rc &= 0x7F;
rc |= (adev->devno << 7);
- outb(rc, ap->ioaddr.lbal_addr);
+ iowrite8(rc, ap->ioaddr.lbal_addr);
/* Write the timings */
- outb(active << 4 | recover, ap->ioaddr.error_addr);
+ iowrite8(active << 4 | recover, ap->ioaddr.error_addr);
/* Select the right bank for read timings, also
load the shared timings for address */
- rc = inb(ap->ioaddr.device_addr);
+ rc = ioread8(ap->ioaddr.device_addr);
rc &= 0xC0;
rc |= adev->devno; /* Index select */
rc |= (setup << 4) | 0x04;
- outb(rc, ap->ioaddr.device_addr);
+ iowrite8(rc, ap->ioaddr.device_addr);
/* Load the read timings */
- outb(active << 4 | recover, ap->ioaddr.data_addr);
+ iowrite8(active << 4 | recover, ap->ioaddr.data_addr);
/* Ensure the timing register mode is right */
- rc = inb (ap->ioaddr.lbal_addr);
+ rc = ioread8(ap->ioaddr.lbal_addr);
rc &= 0x73;
rc |= 0x84;
- outb(rc, ap->ioaddr.lbal_addr);
+ iowrite8(rc, ap->ioaddr.lbal_addr);
/* Exit command mode */
- outb(0x83, ap->ioaddr.nsect_addr);
+ iowrite8(0x83, ap->ioaddr.nsect_addr);
/* We need to know this for quad device on the MVB */
ap->host->private_data = ap;
.qc_prep = ata_qc_prep,
.qc_issue = opti82c46x_qc_issue_prot,
- .data_xfer = ata_pio_data_xfer,
+ .data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
.port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
};
struct legacy_data *ld = &legacy_data[nr_legacy_host];
struct ata_probe_ent ae;
struct platform_device *pdev;
- int ret = -EBUSY;
struct ata_port_operations *ops = &legacy_port_ops;
+ void __iomem *io_addr, *ctrl_addr;
int pio_modes = pio_mask;
u32 mask = (1 << port);
-
- if (request_region(io, 8, "pata_legacy") == NULL)
- return -EBUSY;
- if (request_region(ctrl, 1, "pata_legacy") == NULL)
- goto fail_io;
+ u32 iordy = (iordy_mask & mask) ? 0: ATA_FLAG_NO_IORDY;
+ int ret;
pdev = platform_device_register_simple(DRV_NAME, nr_legacy_host, NULL, 0);
- if (IS_ERR(pdev)) {
- ret = PTR_ERR(pdev);
- goto fail_dev;
- }
+ if (IS_ERR(pdev))
+ return PTR_ERR(pdev);
+
+ ret = -EBUSY;
+ if (devm_request_region(&pdev->dev, io, 8, "pata_legacy") == NULL ||
+ devm_request_region(&pdev->dev, ctrl, 1, "pata_legacy") == NULL)
+ goto fail;
+
+ ret = -ENOMEM;
+ io_addr = devm_ioport_map(&pdev->dev, io, 8);
+ ctrl_addr = devm_ioport_map(&pdev->dev, ctrl, 1);
+ if (!io_addr || !ctrl_addr)
+ goto fail;
if (ht6560a & mask) {
ops = &ht6560a_port_ops;
pio_modes = 0x07;
+ iordy = ATA_FLAG_NO_IORDY;
}
if (ht6560b & mask) {
ops = &ht6560b_port_ops;
printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller detected.\n");
pio_modes = 0x07;
ops = &pdc20230_port_ops;
+ iordy = ATA_FLAG_NO_IORDY;
udelay(100);
inb(0x1F5);
} else {
/* Chip does mode setting by command snooping */
if (ops == &legacy_port_ops && (autospeed & mask))
ops = &simple_port_ops;
+
memset(&ae, 0, sizeof(struct ata_probe_ent));
INIT_LIST_HEAD(&ae.node);
ae.dev = &pdev->dev;
ae.pio_mask = pio_modes;
ae.irq = irq;
ae.irq_flags = 0;
- ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST;
- ae.port[0].cmd_addr = io;
- ae.port[0].altstatus_addr = ctrl;
- ae.port[0].ctl_addr = ctrl;
+ ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST|iordy;
+ ae.port[0].cmd_addr = io_addr;
+ ae.port[0].altstatus_addr = ctrl_addr;
+ ae.port[0].ctl_addr = ctrl_addr;
ata_std_ports(&ae.port[0]);
ae.private_data = ld;
- ret = ata_device_add(&ae);
- if (ret == 0) {
- ret = -ENODEV;
+ ret = -ENODEV;
+ if (!ata_device_add(&ae))
goto fail;
- }
+
legacy_host[nr_legacy_host++] = dev_get_drvdata(&pdev->dev);
ld->platform_dev = pdev;
return 0;
fail:
platform_device_unregister(pdev);
-fail_dev:
- release_region(ctrl, 1);
-fail_io:
- release_region(io, 8);
return ret;
}
for (i = 0; i < nr_legacy_host; i++) {
struct legacy_data *ld = &legacy_data[i];
- struct ata_port *ap =legacy_host[i]->ports[0];
- unsigned long io = ap->ioaddr.cmd_addr;
- unsigned long ctrl = ap->ioaddr.ctl_addr;
- ata_host_remove(legacy_host[i]);
+
+ ata_host_detach(legacy_host[i]);
platform_device_unregister(ld->platform_dev);
if (ld->timing)
release_region(ld->timing, 2);
- release_region(io, 8);
- release_region(ctrl, 1);
}
}
module_param(opti82c611a, int, 0);
module_param(opti82c46x, int, 0);
module_param(pio_mask, int, 0);
+module_param(iordy_mask, int, 0);
module_init(legacy_init);
module_exit(legacy_exit);
projects / linux-drm-fsl-dcu.git / blobdiff