Documentation/devicetree/bindings/mfd/s2mps11.txt

   1
   2 * Samsung S2MPS11 Voltage and Current Regulator
   3
   4 The Samsung S2MPS11 is a multi-function device which includes voltage and
   5 current regulators, RTC, charger controller and other sub-blocks. It is
   6 interfaced to the host controller using an I2C interface. Each sub-block is
   7 addressed by the host system using different I2C slave addresses.
   8
   9 Required properties:
  10 - compatible: Should be "samsung,s2mps11-pmic".
  11 - reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
  12
  13 Optional properties:
  14 - interrupt-parent: Specifies the phandle of the interrupt controller to which
  15   the interrupts from s2mps11 are delivered to.
  16 - interrupts: Interrupt specifiers for interrupt sources.
  17
  18 Optional nodes:
  19 - clocks: s2mps11 provides three(AP/CP/BT) buffered 32.768 KHz outputs, so to
  20   register these as clocks with common clock framework instantiate a sub-node
  21   named "clocks". It uses the common clock binding documented in :
  22   [Documentation/devicetree/bindings/clock/clock-bindings.txt]
  23   - #clock-cells: should be 1.
  24
  25   - The following is the list of clocks generated by the controller. Each clock
  26     is assigned an identifier and client nodes use this identifier to specify
  27     the clock which they consume.
  28     Clock               ID
  29     ----------------------
  30     32KhzAP             0
  31     32KhzCP             1
  32     32KhzBT             2
  33
  34 - regulators: The regulators of s2mps11 that have to be instantiated should be
  35 included in a sub-node named 'regulators'. Regulator nodes included in this
  36 sub-node should be of the format as listed below.
  37
  38         regulator_name {
  39                 [standard regulator constraints....];
  40         };
  41
  42  regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us
  43
  44  BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explictly
  45  regulator-ramp-delay = <0> can be used for them to disable ramp delay.
  46  In the absence of the regulator-ramp-delay property, the default ramp
  47  delay will be used.
  48
  49 NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set
  50 for a particular group of BUCKs. So provide same regulator-ramp-delay<value>.
  51 Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6],
  52 BUCK[3, 4], and BUCK[7, 8, 10]
  53
  54 The regulator constraints inside the regulator nodes use the standard regulator
  55 bindings which are documented elsewhere.
  56
  57 The following are the names of the regulators that the s2mps11 pmic block
  58 supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
  59 as per the datasheet of s2mps11.
  60
  61         - LDOn
  62                   - valid values for n are 1 to 38
  63                   - Example: LDO0, LD01, LDO28
  64         - BUCKn
  65                   - valid values for n are 1 to 10.
  66                   - Example: BUCK1, BUCK2, BUCK9
  67
  68 Example:
  69
  70         s2mps11_pmic@66 {
  71                 compatible = "samsung,s2mps11-pmic";
  72                 reg = <0x66>;
  73
  74                 s2m_osc: clocks{
  75                         #clock-cells = 1;
  76                         clock-output-names = "xx", "yy", "zz";
  77                 };
  78
  79                 regulators {
  80                         ldo1_reg: LDO1 {
  81                                 regulator-name = "VDD_ABB_3.3V";
  82                                 regulator-min-microvolt = <3300000>;
  83                                 regulator-max-microvolt = <3300000>;
  84                         };
  85
  86                         ldo2_reg: LDO2 {
  87                                 regulator-name = "VDD_ALIVE_1.1V";
  88                                 regulator-min-microvolt = <1100000>;
  89                                 regulator-max-microvolt = <1100000>;
  90                                 regulator-always-on;
  91                         };
  92
  93                         buck1_reg: BUCK1 {
  94                                 regulator-name = "vdd_mif";
  95                                 regulator-min-microvolt = <950000>;
  96                                 regulator-max-microvolt = <1350000>;
  97                                 regulator-always-on;
  98                                 regulator-boot-on;
  99                         };
 100
 101                         buck2_reg: BUCK2 {
 102                                 regulator-name = "vdd_arm";
 103                                 regulator-min-microvolt = <950000>;
 104                                 regulator-max-microvolt = <1350000>;
 105                                 regulator-always-on;
 106                                 regulator-boot-on;
 107                                 regulator-ramp-delay = <50000>;
 108                         };
 109                 };
 110         };