[PATCH] libertas: split wext for eth and msh

Separate wireless handlers of mshX and ethX. ethX remains as before.

For mshX, it has been disabled set/get essid, wap and set mode. Get mode always
returns "Repeater" and by now we use the Nickname to show if the mesh is active
("Mesh") or not (empty). The rest remains as before.

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: make mac address configuration work with mesh interface too

Signed-off-by: Luis Carlos Cobo Rus <luiscarlos@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: updated readme file

Fix some wording and blinding table command options, clarify argument list for
fwt_add and fwt_list, simplify fwt_list_route

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: Make WPA work through supplicant handshake

Fix WPA so it works up through the supplicant 4-Way handshake process.
Doesn't successfully pass traffic yet; may be problems installing
the GTK to the firmware.

- RSN needs to be enabled before the association command is sent
- Use keys from the association request not the adapter structure
- cmd_act_mac_strict_protection_enable != IW_AUTH_DROP_UNENCRYPTED
- Fix network filtering logic in is_network_compatible() WPA helpers

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: add more verbose debugging to libertas_cmd_80211_authenticate

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: debug print spacing fixes in assoc.c

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: send SIOCGIWSCAN event after partial scans too

Any time the driver gets new scan results, even from partial scans,
it should send the scan event to userspace.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: honor specific channel requests during association

Previously if a fixed channel was specified along with an SSID,
the channel request would be ignored during the association
process.  Instead, when searching for an adhoc or infrastructure
network to join, allow filtering results based on channel so
that the driver doesn't pick a BSS on a different channel than
requested.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix default adhoc channel

Inadvertently removed on a previous commit; causes the first
adhoc start to fail if a channel has not been set or no
other association has been made.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix deadlock SIOCGIWSCAN handler

Update signal quality before the locked scan result translation loop,
because calling libertas_prepare_and_send_command() with the
'waitforrsp' option grabs adapter->lock in the command return processing,
leading to the deadlock.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: correct error report paths for wlan_fwt_list_ioctl

Ensure the leave debug print gets triggered when necessary.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: correctly balance locking in libertas_process_rx_command

adapter->lock should released after unlocking adapter->driver_lock to
balance the order in which they were locked at the top of the function.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix debug enter/leave prints for libertas_execute_next_command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: use compare_ether_addr() rather than memcmp() where appropriate

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: use MAC_FMT and MAC_ARG where appropriate

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: make association paths consistent

The BSS to associate with (in either Infrastructure or IBSS join
operations) is now stored in _one_ place in the association request (the
bss member), not two places as before (pattemptedbss and
curbssparams->bssdescriptor).

Association requests are passed to the necessary association functions
to (a) give them access to the bss member and (b) ensure that
association/join/start setup uses settings from the request, not the
current adapter settings (which may not be valid for the requested
settings).

Because the 'bss' member of the association request is used now, the
command return functions from associate and adhoc join/start need access
to the in-progress association request to update curbssparams when
everything is done.  The association worker moves the request from
pending to in-progress for the duration of the association attempt.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: move channel changing into association framework

Handle channel changes through the deferred association framework
rather than directly.  Fixes errors when setting channels along
with other parameters like mode and SSID.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix oops on rmmod

Use list_for_each_entry_safe, to protect against list_del().

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: cleanup of fwt_list_route processing

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix 'keep previous scan' behavior

Do not clear the scan list except under specific conditions, such as
when (a) user-requested, or (b) joining/starting an adhoc network.
Furthermore, only clear entries which match the SSID or BSSID of the
request, not the whole scan list.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: make scan result handling more flexible

- use a linked list for scan results
- age scan results
- pass bss_descriptors around instead of indexes into the scan table
- lock access to the scan results
- stop returning EAGAIN from SIOCGIWSCAN handler

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: updated mesh commands for 5.220.9.p11

Updated commands fwt_add and fwt_list, bt_list.
New commands: bt_get_invert, bt_set_invert, to invert the blinding table,
i.e., receive only frames from nodes listed in the BT.

This patch needs/is needed for firmware 5.220.9.p11.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: version bump (321p0) and cmds update for new fw (5.220.10.p0)

This patch along with the previous commands update one, is necessary for
mesh and fwt ioctls to work properly with firmware version 5.220.10.p0
and later.

Signed-off-by: Luis Carlos Cobo Rus <luiscarlos@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: don't tear down netdev in libertas_activate_card

libertas_activate_card() doesn't create the netdev, and shouldn't
free it on error.  The caller of libertas_activate_card() is
responsible for cleaning up errors from libertas_add_card(),
not libertas_activate_card().

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: correctly unregister mesh netdev on error

Subject says it all.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: replace 'macaddress' with 'bssid'

Start to normalize bss_descriptor with ieee80211_network so we can
eventually replace bss_descriptor more easily.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: call SET_NETDEV_DEV from common code

Move usage of SET_NETDEV_DEV into common code since it has nothing
to do with bus-specific devices.  Also fixes a bug where the mesh
device was getting SET_NETDEV_DEV called after register_netdevice,
resulting in no 'device' link in /sys/class/net/mshX/.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fixed kernel oops on module/card removal

Fixed kernel oops on module/card removal (using dongles)

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: add URB debug info

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fixed incorrect assigment of fcs errors to frag errors

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove unused variables in wlan_dev_t

Actually, this patch removev wlan_dev_t totally and puts the used variables
of it directly into wlan_private. That reduces one level of indirection and
looks a little bit simpler. It's now "priv->card" and not
"priv->wlan_dev.card" and "priv->dev" instead of "priv->wlan_dev.netdev"

Changed two occurences of "((wlan_private *) dev->priv)->wlan_dev.netdev"
into "dev", because I didn't see the point in doing pointer-ping-pong.

The variables "ioport", "upld_rcv" and "upld_type" where unused. They have
been removed.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: let DRV_NAME be overridable

For now, it's "libertas" by default, but that is overwritten in
if_usb.c/if_bootcmd.c and in if_cs.c.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix RESET logic at unload time

Previously, we had a fixed array of 5 elements where we remembered all
initialized devices. This has been changed to use a "struct list_head"
organization, which is IMHO cleaner.

Also renamed usb_cardp to cardp, as in the reset of the code.

Renamed reset_device() to if_usb_reset_device() like many other functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: split module into two (libertas.ko and usb8xxx.ko)

* add CONFIG_LIBERTAS to Kconfig
* remove global variable libertas_fw_name, the USB module might want to
    use a different default FW name than the CF module, so libertas_fw_name
    is now local to if_usb.c
* exported some symbols as GPL

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: move contents of fw.h to decl.h

Also removes some useless "extern" declarations from function declaration.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: indirect all hardware access via hw_XXXX functions

This functions makes all libertas_sbi_XXX functions static to the
if_usb.c file and renames them to if_usb_XXXX(). The get called from
other places of the source code via priv->hw_XXXX().

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: wakeup both mesh and normal wakeup when getting out of scan

The previous patch wakes up the mesh device *instead* of the wlan device
when coming out of scan. We need to wake up both of them.

Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: added transmission failures to mesh statistics

Added transmission failures to mesh statistics.
Removed whitespace before newlines.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix error handling of card initialization

Subject says it all.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fixed transmission flow control on the mesh interface

This patch implements proper transmission flow control on mshX.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: split wlan_add_card()

Split wlan_add_card() into a part that just setups kernel parameters and
into the function libertas_activate_card(), which will implizitly use
hardware functions by the started thread.

This allows us later to do something like this:

priv = libertas_add_card();
priv->hw_command_to_host = if_usb_command_to_host;
priv->hw_xxxx = if_usb_xxxx;
priv->hw_yyyy = if_usb_yyyy;
wlan_activate_card()

and of course the CF driver can set it's own functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: move reset_device() code main.c to if_usb.c

The reset_device() logic is only needed for USB devices, not for CF
devices.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: changed some occurences of kmalloc() + memset(&a,0,sz) to kzalloc()

The subject says it all.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix SSID output

* a newline was missing
* changed %32s to '%s', no need to right justify the ESSID

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: get rid of libertas_sbi_get_priv()

It's not really needed, because we can call wlan_remove_card() with
wlan_private* anyway.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: change debug output of libertas_interrupt()

It used to be LBS_DEB_MAIN, now it's LBS_DEB_THREAD

Also fixed a missing ":" in lbs_deb_enter()

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: single out mesh code

This patches adds the two functions wlan_add_mesh() and wlan_remove_mesh(),
which are responsible for the mshX interface. In a CF driver with a non-
mesh-aware firmware you can omit the calls to this functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: tune debug code

* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
    source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: make debug configurable

The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: exclude non-used code when PROC_DEBUG is not set

This reduces usb8xxx.ko by 951 bytes (text) and 256 bytes (data)
when PROC_DEBUG isn't defined.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix scanning from associate path

The previous scan fix did not account for scan paths other than set_scan()
that need to do a full scan at once.

Add a "full_scan" parameter to wlan_scan_networks() to control such
behaviour.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: make libertas_wlan_data_rates static

Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: move vendor & product id's into if_usb.c

For me it looks cleaner, because it removes one level of indirection.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove unused/superfluous definitions of DEV_NAME_LEN

DEV_NAME_LEN is already defined in defs.h and that is sufficient.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove __FILE__ from debug output

Remove filename from debug output because it's way too long.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove deprecated pm_register and associated code

Subject says it all.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix removal of all debugfs files

rmmod did not remove /sys/kernel/debug/libertas_wireless/eth1/
subscribed_events/high_snr. After I fixed this, I noticed that
it also didn't remove /sys/kernel/debug/libertas_wireless/eth1
as well.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: a debug output was missing a newline

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: rename wlan_association_worker

Renames wlan_association_worker into libertas_association_worker

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: scan two channels per scan command

Scan two channels per each command on set_scan(), then bail out and let
get_scan() continue the scanning work up to the last channel.

This gives time to the firmware so it can go back to the association
channel and keep the connection alive.

Fixes http://dev.laptop.org/ticket/841

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[MIPS] Fix smp barriers in test_and_{change,clear,set}_bit

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix IP27 build

IP27 does no longer have ZONE_DMA.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix modpost warnings by making start_secondary __cpuinit

WARNING: arch/mips/kernel/built-in.o(.text+0x9a58): Section mismatch: reference to .init.text:cpu_report (between 'start_secondary' and 'smp_prepare_boot_cpu')
WARNING: arch/mips/kernel/built-in.o(.text+0x9a60): Section mismatch: reference to .init.text:per_cpu_trap_init (between 'start_secondary' and 'smp_prepare_boot_cpu')
WARNING: arch/mips/kernel/built-in.o(.text+0x9adc): Section mismatch: reference to .init.text:cpu_probe (between 'start_secondary' and 'smp_prepare_boot_cpu')
mipsel-linux-objcopy -S -O srec --remove-section=.reginfo --remove-section=.mdebug --remove-section=.comment --remove-section=.note --remove-section=.pdr --remove-section=.options --remove-section=.MIPS.options vmlinux arch/mips/boot/vmlinux.srec

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SMTC: Fix build error caused by nonsense code.

Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SMTC: The MT ASE requires to initialize c0_pagemask and c0_wired.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SMTC: Don't continue in set_vi_srs_handler on detected bad arguments.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SMTC: Fix warning.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Wire up utimensat, signalfd, timerfd, eventfd

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Atlas: Fix build.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Always install the DSP exception handler.

Some non-DSP enabled cores 24K / 34K can generate a DSP exception where they
are actually expected to produce a reserved instruction exception.

Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SMTC: Don't set and restore irqregs ptr from self_ipi.

This did corrupt register s0 which the caller of self_ipi expects to
be unchanged.  This is a kernel bug which will only be triggered with
the compilers which compile __smtc_ipi_replay to use s0 across the
invocation of self_ipi. Gcc 4.1.2 does this, for example.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix KMODE for the R3000

 This must be the oldest bug that we have got.  Leaving interrupts "as
they are" for the R3000 obviously means copying IEp to IEc.  Since we have
got STATMASK now, I took this opportunity to mask the status register
"correctly" for the R3000 now too.  Oh, and the R3000 hardly ever is
64-bit.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Blackfin SMC91X ethernet supporting driver: SMC91C111 LEDs are note drived in the kernel like in uboot

Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin SPI driver: fix bug SPI DMA incomplete transmission

SPI writes intermittently drop bytes at end of DMA transfer
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3205
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=2892

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

[ARM] 4445/1: ANUBIS: Fix CPLD registers

Update the ANUBIS register definitions inline with the
specs and ensure they are registered correctly.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 4444/2: OSIRIS: CPLD suspend fix

Ensure the CPLD 8bit settings are preserved over a suspend/resume
cycle as the CPU sends a hard-reset at resume time.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 4443/1: OSIRIS: Add watchdog device to machine devices

Add the watchdog timer to the list of devices
the Osiris registers at startup.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 4442/1: OSIRIS: Fix CPLD register definitions

Fix the CPLD register definitions to correctly mirror the
documentation

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Blackfin SPI driver: tweak spi cleanup function to match newer kernel changes

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>

Blackfin RTC drivers: update MAINTAINERS information

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>

Blackfin serial driver: decouple PARODD and CMSPAR checking from PARENB

as the termios info does not stipulate that the former are dependent on the latter

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin serial driver: actually implement the break_ctl() function

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin serial driver: ignore framing and parity errors

if we get a break signal, we want to ignore framing and parity errors
because those will always be set (by nature of the signal)

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin serial driver: hook up our UARTs STP bit with userspaces CMSPAR

so we can now do spaced/marked parity

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: move HI/LO macros into blackfin.h and punt the rest of macros.h as it includes VDSP macros we never use

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: redo our linker script a bit

 - we can start taking advantages of defines in asm-generic/vmlinux.lds.h
 - move our L1 relocated sections into init so it gets freed after relocation

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: make sure we initialize our L1 Data B section properly based on the linked kernel

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: fix bug can not wakeup from sleep via push buttons

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: add support for Alon Bar-Lev's dynamic kernel command-line

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: add missing gpio.h header to fix compiling in some pm configurations

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: As Mike pointed out range goes form m..MAX_BLACKFIN_GPIO -1

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: fix spelling typo in output

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: try to split up functions like this into smaller units according to LKML review

Signed-off-by: Aubrey Li <aubrey.li@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: add proper ENDPROC()

add proper ENDPROC() to close out assembly functions
so size/type is set properly in the final ELF image

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: move more of our startup code to .init so it can be freed once we are up and running

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: unify differences between our diff head.S files -- no functional changes

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: update defconfigs

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: scrub old console defines

since they arent respected anymore (use console=) and just confuse people

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: fixup Blackfin MAINTIANERS team member list

Signed-off-by: Bryan Wu <bryan.wu@analog.com>

Blackfin arch: implement a basic /proc/sram file for L1 allocation visibility

implement a basic /proc/sram file for L1 allocation visibility until we can
rewrite the entire L1 allocator (which would include a proper mechanism)

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>