nds32: add support for leopard and orca board boot flow auto detect
authorrick <rick@andestech.com>
Fri, 24 Jan 2014 09:14:28 +0000 (17:14 +0800)
committerKuan-Yu Kuo <ken.kuoky@gmail.com>
Tue, 28 Jan 2014 11:23:01 +0000 (19:23 +0800)
hardware difference between leopard and orca as below:

flash setting     leoaprd     orca
bank size         32MB        64MB
bus width         32-bits     16-bits

Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
arch/nds32/cpu/n1213/ag101/asm-offsets.c
arch/nds32/cpu/n1213/ag101/lowlevel_init.S

index 92ada8ac2881771074cc74703e9f5aeb9da63765..cfe52d1df4a367ad87856d7ea51cd7e54817a465 100644 (file)
@@ -21,6 +21,7 @@ int main(void)
 #endif
        BLANK();
 #ifdef CONFIG_FTAHBC020S
+       OFFSET(FTAHBC020S_SLAVE_BSR_4,  ftahbc02s, s_bsr[4]);
        OFFSET(FTAHBC020S_SLAVE_BSR_6,  ftahbc02s, s_bsr[6]);
        OFFSET(FTAHBC020S_CR,           ftahbc02s, cr);
 #endif
index 810326d20052e7e95accc7a02232eddb416bb3af..d6484b9cc59b44dd7f0a08c3d460493f1f228d56 100644 (file)
 #define SDMC_B0_BSR_D          CONFIG_SYS_FTSDMC021_BANK0_BSR
 #define SDMC_B1_BSR_D          CONFIG_SYS_FTSDMC021_BANK1_BSR
 
+
+/*
+ * for Orca and Emerald
+ */
+#define BOARD_ID_REG           0x104
+#define BOARD_ID_FAMILY_MASK   0xfff000
+#define BOARD_ID_FAMILY_V5     0x556000
+#define BOARD_ID_FAMILY_K7     0x74b000
+
 /*
  * parameters for the static memory controller
  */
 #define AHBC_CR_A              (CONFIG_FTAHBC020S_BASE + FTAHBC020S_CR)
 #define AHBC_BSR6_A    (CONFIG_FTAHBC020S_BASE + FTAHBC020S_SLAVE_BSR_6)
 
+/*
+ * for Orca and Emerald
+ */
+#define AHBC_BSR4_A    (CONFIG_FTAHBC020S_BASE + FTAHBC020S_SLAVE_BSR_4)
 #define AHBC_BSR6_D            CONFIG_SYS_FTAHBC020S_SLAVE_BSR_6
 
 /*
@@ -100,14 +113,49 @@ mem_init:
         *      we need to set onboard SDRAM before remap and relocation.
         */
        led     0x01
-       write32 SMC_BANK0_CR_A, SMC_BANK0_CR_D                  ! 0x10000052
-       write32 SMC_BANK0_TPR_A, SMC_BANK0_TPR_D                ! 0x00151151
+
+  /*
+   * for Orca and Emerald
+   * disable write protection and reset bank size
+   */
+       li      $r0, SMC_BANK0_CR_A
+       lwi $r1, [$r0+#0x00]
+       ori $r1, $r1, 0x8f0
+       xori $r1, $r1, 0x8f0
+  /*
+   * check board
+   */
+       li      $r3, CONFIG_FTPMU010_BASE + BOARD_ID_REG
+  lwi     $r3, [$r3]
+  li      $r4, BOARD_ID_FAMILY_MASK
+  and     $r3, $r3, $r4
+  li      $r4, BOARD_ID_FAMILY_K7
+  xor     $r4, $r3, $r4
+  beqz    $r4, use_flash_16bit_boot
+  /*
+   * 32-bit mode
+   */
+use_flash_32bit_boot:
+       ori     $r1, $r1, 0x50
+  li      $r2, 0x00151151
+  j       sdram_b0_cr
+  /*
+   * 16-bit mode
+   */
+use_flash_16bit_boot:
+  ori     $r1, $r1, 0x60
+  li      $r2, 0x00153153
+  /*
+   * SRAM bank0 config
+   */
+sdram_b0_cr:
+  swi     $r1, [$r0+#0x00]
+  swi     $r2, [$r0+#0x04]
 
        /*
         * config AHB Controller
         */
        led     0x02
-       write32 AHBC_BSR6_A, AHBC_BSR6_D
 
        /*
         * config PMU controller
@@ -194,7 +242,16 @@ relo_base:
         * a FLASH connected to bank0.
         */
        led     0x11
-       li      $r4, PHYS_SDRAM_0_AT_INIT               /* 0x10000000 */
+   /*
+    * for Orca and Emerald
+    * read sdram base address automatically
+    */
+       li      $r5, AHBC_BSR6_A
+       lwi $r8, [$r5]
+       li      $r4, 0xfff00000
+       and $r4, $r4, $r8
+
+
        li      $r5, 0x0
        la      $r1, relo_base                          /* get $pc or $lp */
        sub     $r2, $r0, $r1
@@ -218,6 +275,29 @@ relo_base:
        write32 SDMC_B1_BSR_A, 0x00001040
        setbf15 AHBC_CR_A, FTAHBC020S_CR_REMAP          ! 0x1
 
+  /*
+   * for Orca and Emerald
+   * extend sdram size from 256MB to 2GB
+   */
+       li      $r5, AHBC_BSR6_A
+       lwi $r6, [$r5]
+       li  $r4, 0xfff0ffff
+       and $r6 ,$r4 , $r6
+       li      $r4, 0x000b0000
+       or  $r6, $r4,   $r6
+       swi     $r6, [$r5]
+
+  /*
+   * for Orca and Emerald
+   * extend rom base from 256MB to 2GB
+   */
+       li      $r4, AHBC_BSR4_A
+       lwi $r5, [$r4]
+       li      $r6, 0xffffff
+       and $r5, $r5, $r6
+       li  $r6, 0x80000000
+       or  $r5, $r5, $r6
+       swi $r5,        [$r4]
 #endif /* #ifdef CONFIG_MEM_REMAP */
        move    $lp, $r11
 2: