platforms += sni
platforms += txx9
platforms += vr41xx
-platforms += wrppmc
# include the platform specific files
include $(patsubst %, $(srctree)/arch/mips/%/Platform, $(platforms))
config MIPS
bool
default y
+ select HAVE_CONTEXT_TRACKING
select HAVE_GENERIC_DMA_COHERENT
select HAVE_IDE
select HAVE_OPROFILE
select HAVE_GENERIC_HARDIRQS
select GENERIC_IRQ_PROBE
select GENERIC_IRQ_SHOW
+ select GENERIC_PCI_IOMAP
select HAVE_ARCH_JUMP_LABEL
select ARCH_WANT_IPC_PARSE_VERSION
select IRQ_FORCED_THREADING
menu "Machine selection"
-config ZONE_DMA
- bool
-
choice
prompt "System type"
default SGI_IP22
config BCM63XX
bool "Broadcom BCM63XX based boards"
+ select BOOT_RAW
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select SYS_HAS_CPU_MIPS32_R1
+ select SYS_HAS_CPU_BMIPS4350 if !BCM63XX_CPU_6338 && !BCM63XX_CPU_6345 && !BCM63XX_CPU_6348
+ select NR_CPUS_DEFAULT_2
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_HAS_EARLY_PRINTK
select DMA_NONCOHERENT
select IRQ_CPU
select IRQ_GIC
- select MIPS_CPU_SCACHE
select MIPS_MSC
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_CPU_MIPS32_R2
select CSRC_POWERTV
select DMA_NONCOHERENT
select HW_HAS_PCI
- select SYS_HAS_EARLY_PRINTK
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
Support the Mikrotik(tm) RouterBoard 532 series,
based on the IDT RC32434 SoC.
-config WR_PPMC
- bool "Wind River PPMC board"
- select CEVT_R4K
- select CSRC_R4K
- select IRQ_CPU
- select BOOT_ELF32
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select PCI_GT64XXX_PCI0
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_MIPS32_R1
- select SYS_HAS_CPU_MIPS32_R2
- select SYS_HAS_CPU_MIPS64_R1
- select SYS_HAS_CPU_NEVADA
- select SYS_HAS_CPU_RM7000
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_LITTLE_ENDIAN
- help
- This enables support for the Wind River MIPS32 4KC PPMC evaluation
- board, which is based on GT64120 bridge chip.
-
-config CAVIUM_OCTEON_SIMULATOR
- bool "Cavium Networks Octeon Simulator"
- select CEVT_R4K
- select 64BIT_PHYS_ADDR
- select DMA_COHERENT
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_HOTPLUG_CPU
- select SYS_HAS_CPU_CAVIUM_OCTEON
- select HOLES_IN_ZONE
- help
- The Octeon simulator is software performance model of the Cavium
- Octeon Processor. It supports simulating Octeon processors on x86
- hardware.
-
-config CAVIUM_OCTEON_REFERENCE_BOARD
- bool "Cavium Networks Octeon reference board"
+config CAVIUM_OCTEON_SOC
+ bool "Cavium Networks Octeon SoC based boards"
select CEVT_R4K
select 64BIT_PHYS_ADDR
select DMA_COHERENT
select SYS_HAS_EARLY_PRINTK
select USB_ARCH_HAS_OHCI if USB_SUPPORT
select USB_ARCH_HAS_EHCI if USB_SUPPORT
+ select SYS_SUPPORTS_ZBOOT
+ select SYS_SUPPORTS_ZBOOT_UART16550
help
Support for systems based on Netlogic XLR and XLS processors.
Say Y here if you have a XLR or XLS based board.
select SYNC_R4K
select SYS_HAS_EARLY_PRINTK
select USE_OF
+ select SYS_SUPPORTS_ZBOOT
+ select SYS_SUPPORTS_ZBOOT_UART16550
help
This board is based on Netlogic XLP Processor.
Say Y here if you have a XLP based board.
config CPU_LITTLE_ENDIAN
bool "Little endian"
depends on SYS_SUPPORTS_LITTLE_ENDIAN
- help
endchoice
config MIPS_VPE_LOADER
bool "VPE loader support."
- depends on SYS_SUPPORTS_MULTITHREADING
+ depends on SYS_SUPPORTS_MULTITHREADING && MODULES
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select MIPS_MT
If unsure, say Y. Only embedded should say N here.
+config CC_STACKPROTECTOR
+ bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
+ help
+ This option turns on the -fstack-protector GCC feature. This
+ feature puts, at the beginning of functions, a canary value on
+ the stack just before the return address, and validates
+ the value just before actually returning. Stack based buffer
+ overflows (that need to overwrite this return address) now also
+ overwrite the canary, which gets detected and the attack is then
+ neutralized via a kernel panic.
+
+ This feature requires gcc version 4.2 or above.
+
config USE_OF
bool
select OF
bool "Support for PCI controller"
depends on HW_HAS_PCI
select PCI_DOMAINS
- select GENERIC_PCI_IOMAP
select NO_GENERIC_PCI_IOPORT_MAP
help
Find out whether you have a PCI motherboard. PCI is the name of a
select CLKEVT_I8253
select MIPS_EXTERNAL_TIMER
+config ZONE_DMA
+ bool
+
config ZONE_DMA32
bool
LDFLAGS += -m $(ld-emul)
+ifdef CONFIG_CC_STACKPROTECTOR
+ KBUILD_CFLAGS += -fstack-protector
+endif
+
ifdef CONFIG_MIPS
CHECKFLAGS += $(shell $(CC) $(KBUILD_CFLAGS) -dM -E -x c /dev/null | \
egrep -vw '__GNUC_(|MINOR_|PATCHLEVEL_)_' | \
ath79_register_pci();
}
#else
-static inline void ap136_pci_init(void) {}
+static inline void ap136_pci_init(u8 *eeprom) {}
#endif /* CONFIG_PCI */
static void __init ap136_setup(void)
menu "CPU support"
depends on BCM63XX
+config BCM63XX_CPU_3368
+ bool "support 3368 CPU"
+ select HW_HAS_PCI
+
config BCM63XX_CPU_6328
bool "support 6328 CPU"
select HW_HAS_PCI
config BCM63XX_CPU_6338
bool "support 6338 CPU"
select HW_HAS_PCI
- select USB_ARCH_HAS_OHCI
- select USB_OHCI_BIG_ENDIAN_DESC
- select USB_OHCI_BIG_ENDIAN_MMIO
config BCM63XX_CPU_6345
bool "support 6345 CPU"
- select USB_OHCI_BIG_ENDIAN_DESC
- select USB_OHCI_BIG_ENDIAN_MMIO
config BCM63XX_CPU_6348
bool "support 6348 CPU"
#include <bcm63xx_dev_usb_usbd.h>
#include <board_bcm963xx.h>
+#include <uapi/linux/bcm933xx_hcs.h>
+
#define PFX "board_bcm963xx: "
+#define HCS_OFFSET_128K 0x20000
+
static struct board_info board;
+/*
+ * known 3368 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_3368
+static struct board_info __initdata board_cvg834g = {
+ .name = "CVG834G_E15R3921",
+ .expected_cpu_id = 0x3368,
+
+ .has_uart0 = 1,
+ .has_uart1 = 1,
+
+ .has_enet0 = 1,
+ .has_pci = 1,
+
+ .enet0 = {
+ .has_phy = 1,
+ .use_internal_phy = 1,
+ },
+
+ .leds = {
+ {
+ .name = "CVG834G:green:power",
+ .gpio = 37,
+ .default_trigger= "default-on",
+ },
+ },
+
+ .ephy_reset_gpio = 36,
+ .ephy_reset_gpio_flags = GPIOF_INIT_HIGH,
+};
+#endif
+
/*
* known 6328 boards
*/
* all boards
*/
static const struct board_info __initconst *bcm963xx_boards[] = {
+#ifdef CONFIG_BCM63XX_CPU_3368
+ &board_cvg834g,
+#endif
#ifdef CONFIG_BCM63XX_CPU_6328
&board_96328avng,
#endif
unsigned int i;
u8 *boot_addr, *cfe;
char cfe_version[32];
- char *board_name;
+ char *board_name = NULL;
u32 val;
+ struct bcm_hcs *hcs;
/* read base address of boot chip select (0)
* 6328/6362 do not have MPI but boot from a fixed address
bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET);
- board_name = bcm63xx_nvram_get_name();
+ if (BCMCPU_IS_3368()) {
+ hcs = (struct bcm_hcs *)boot_addr;
+ board_name = hcs->filename;
+ } else {
+ board_name = bcm63xx_nvram_get_name();
+ }
/* find board by name */
for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
if (strncmp(board_name, bcm963xx_boards[i]->name, 16))
platform_device_register(&bcm63xx_gpio_leds);
+ if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags)
+ gpio_request_one(board.ephy_reset_gpio,
+ board.ephy_reset_gpio_flags, "ephy-reset");
+
return 0;
}
else
clk_disable_unlocked(&clk_enet_misc);
- if (BCMCPU_IS_6358()) {
+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) {
u32 mask;
if (clk->id == 0)
*/
static void ephy_set(struct clk *clk, int enable)
{
- if (!BCMCPU_IS_6358())
- return;
- bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable);
+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358())
+ bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable);
}
*/
static void pcm_set(struct clk *clk, int enable)
{
- if (!BCMCPU_IS_6358())
- return;
- bcm_hwclock_set(CKCTL_6358_PCM_EN, enable);
+ if (BCMCPU_IS_3368())
+ bcm_hwclock_set(CKCTL_3368_PCM_EN, enable);
+ if (BCMCPU_IS_6358())
+ bcm_hwclock_set(CKCTL_6358_PCM_EN, enable);
}
static struct clk clk_pcm = {
mask = CKCTL_6338_SPI_EN;
else if (BCMCPU_IS_6348())
mask = CKCTL_6348_SPI_EN;
- else if (BCMCPU_IS_6358())
+ else if (BCMCPU_IS_3368() || BCMCPU_IS_6358())
mask = CKCTL_6358_SPI_EN;
else if (BCMCPU_IS_6362())
mask = CKCTL_6362_SPI_EN;
EXPORT_SYMBOL(clk_get_rate);
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ return 0;
+}
+EXPORT_SYMBOL_GPL(clk_set_rate);
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ return 0;
+}
+EXPORT_SYMBOL_GPL(clk_round_rate);
+
struct clk *clk_get(struct device *dev, const char *id)
{
if (!strcmp(id, "enet0"))
return &clk_xtm;
if (!strcmp(id, "periph"))
return &clk_periph;
- if (BCMCPU_IS_6358() && !strcmp(id, "pcm"))
+ if ((BCMCPU_IS_3368() || BCMCPU_IS_6358()) && !strcmp(id, "pcm"))
return &clk_pcm;
if ((BCMCPU_IS_6362() || BCMCPU_IS_6368()) && !strcmp(id, "ipsec"))
return &clk_ipsec;
static unsigned int bcm63xx_cpu_freq;
static unsigned int bcm63xx_memory_size;
+static const unsigned long bcm3368_regs_base[] = {
+ __GEN_CPU_REGS_TABLE(3368)
+};
+
+static const int bcm3368_irqs[] = {
+ __GEN_CPU_IRQ_TABLE(3368)
+};
+
static const unsigned long bcm6328_regs_base[] = {
__GEN_CPU_REGS_TABLE(6328)
};
static unsigned int detect_cpu_clock(void)
{
switch (bcm63xx_get_cpu_id()) {
+ case BCM3368_CPU_ID:
+ return 300000000;
+
case BCM6328_CPU_ID:
{
unsigned int tmp, mips_pll_fcvo;
banks = (val & SDRAM_CFG_BANK_MASK) ? 2 : 1;
}
- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
val = bcm_memc_readl(MEMC_CFG_REG);
rows = (val & MEMC_CFG_ROW_MASK) >> MEMC_CFG_ROW_SHIFT;
cols = (val & MEMC_CFG_COL_MASK) >> MEMC_CFG_COL_SHIFT;
chipid_reg = BCM_6345_PERF_BASE;
break;
case CPU_BMIPS4350:
- if ((read_c0_prid() & 0xf0) == 0x10)
+ switch ((read_c0_prid() & 0xff)) {
+ case 0x04:
+ chipid_reg = BCM_3368_PERF_BASE;
+ break;
+ case 0x10:
chipid_reg = BCM_6345_PERF_BASE;
- else
+ break;
+ default:
chipid_reg = BCM_6368_PERF_BASE;
+ break;
+ }
break;
}
bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT;
switch (bcm63xx_cpu_id) {
+ case BCM3368_CPU_ID:
+ bcm63xx_regs_base = bcm3368_regs_base;
+ bcm63xx_irqs = bcm3368_irqs;
+ break;
case BCM6328_CPU_ID:
bcm63xx_regs_base = bcm6328_regs_base;
bcm63xx_irqs = bcm6328_irqs;
case BCM6348_CPU_ID:
/* no way to auto detect so assume parallel */
return BCM63XX_FLASH_TYPE_PARALLEL;
+ case BCM3368_CPU_ID:
case BCM6358_CPU_ID:
val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL)
{
if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
bcm63xx_regs_spi = bcm6348_regs_spi;
- if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() ||
+ BCMCPU_IS_6362() || BCMCPU_IS_6368())
bcm63xx_regs_spi = bcm6358_regs_spi;
}
#else
spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH;
}
- if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6362() ||
+ BCMCPU_IS_6368()) {
spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT;
if (id >= ARRAY_SIZE(bcm63xx_uart_devices))
return -ENODEV;
- if (id == 1 && (!BCMCPU_IS_6358() && !BCMCPU_IS_6368()))
+ if (id == 1 && (!BCMCPU_IS_3368() && !BCMCPU_IS_6358() &&
+ !BCMCPU_IS_6368()))
return -ENODEV;
if (id == 0) {
static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused;
#ifndef BCMCPU_RUNTIME_DETECT
+#ifdef CONFIG_BCM63XX_CPU_3368
+#define irq_stat_reg PERF_IRQSTAT_3368_REG
+#define irq_mask_reg PERF_IRQMASK_3368_REG
+#define irq_bits 32
+#define is_ext_irq_cascaded 0
+#define ext_irq_start 0
+#define ext_irq_end 0
+#define ext_irq_count 4
+#define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_3368
+#define ext_irq_cfg_reg2 0
+#endif
#ifdef CONFIG_BCM63XX_CPU_6328
#define irq_stat_reg PERF_IRQSTAT_6328_REG
#define irq_mask_reg PERF_IRQMASK_6328_REG
irq_mask_addr = bcm63xx_regset_address(RSET_PERF);
switch (bcm63xx_get_cpu_id()) {
+ case BCM3368_CPU_ID:
+ irq_stat_addr += PERF_IRQSTAT_3368_REG;
+ irq_mask_addr += PERF_IRQMASK_3368_REG;
+ irq_bits = 32;
+ ext_irq_count = 4;
+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368;
+ break;
case BCM6328_CPU_ID:
irq_stat_addr += PERF_IRQSTAT_6328_REG;
irq_mask_addr += PERF_IRQMASK_6328_REG;
if (cause & CAUSEF_IP7)
do_IRQ(7);
+ if (cause & CAUSEF_IP0)
+ do_IRQ(0);
+ if (cause & CAUSEF_IP1)
+ do_IRQ(1);
if (cause & CAUSEF_IP2)
dispatch_internal();
if (!is_ext_irq_cascaded) {
reg &= ~EXTIRQ_CFG_BOTHEDGE_6348(irq);
break;
+ case BCM3368_CPU_ID:
case BCM6328_CPU_ID:
case BCM6338_CPU_ID:
case BCM6345_CPU_ID:
{
unsigned int check_len;
u32 crc, expected_crc;
+ u8 hcs_mac_addr[ETH_ALEN] = { 0x00, 0x10, 0x18, 0xff, 0xff, 0xff };
/* extract nvram data */
memcpy(&nvram, addr, sizeof(nvram));
if (crc != expected_crc)
pr_warn("nvram checksum failed, contents may be invalid (expected %08x, got %08x)\n",
expected_crc, crc);
+
+ /* Cable modems have a different NVRAM which is embedded in the eCos
+ * firmware and not easily extractible, give at least a MAC address
+ * pool.
+ */
+ if (BCMCPU_IS_3368()) {
+ memcpy(nvram.mac_addr_base, hcs_mac_addr, ETH_ALEN);
+ nvram.mac_addr_count = 2;
+ }
}
u8 *bcm63xx_nvram_get_name(void)
#include <linux/init.h>
#include <linux/bootmem.h>
+#include <linux/smp.h>
#include <asm/bootinfo.h>
+#include <asm/bmips.h>
+#include <asm/smp-ops.h>
+#include <asm/mipsregs.h>
#include <bcm63xx_board.h>
#include <bcm63xx_cpu.h>
#include <bcm63xx_io.h>
bcm_wdt_writel(WDT_STOP_2, WDT_CTL_REG);
/* disable all hardware blocks clock for now */
- if (BCMCPU_IS_6328())
+ if (BCMCPU_IS_3368())
+ mask = CKCTL_3368_ALL_SAFE_EN;
+ else if (BCMCPU_IS_6328())
mask = CKCTL_6328_ALL_SAFE_EN;
else if (BCMCPU_IS_6338())
mask = CKCTL_6338_ALL_SAFE_EN;
/* do low level board init */
board_prom_init();
+
+ if (IS_ENABLED(CONFIG_CPU_BMIPS4350) && IS_ENABLED(CONFIG_SMP)) {
+ /* set up SMP */
+ register_smp_ops(&bmips_smp_ops);
+
+ /*
+ * BCM6328 might not have its second CPU enabled, while BCM6358
+ * needs special handling for its shared TLB, so disable SMP
+ * for now.
+ */
+ if (BCMCPU_IS_6328()) {
+ reg = bcm_readl(BCM_6328_OTP_BASE +
+ OTP_USER_BITS_6328_REG(3));
+
+ if (reg & OTP_6328_REG3_TP1_DISABLED)
+ bmips_smp_enabled = 0;
+ } else if (BCMCPU_IS_6358()) {
+ bmips_smp_enabled = 0;
+ }
+
+ if (!bmips_smp_enabled)
+ return;
+
+ /*
+ * The bootloader has set up the CPU1 reset vector at
+ * 0xa000_0200.
+ * This conflicts with the special interrupt vector (IV).
+ * The bootloader has also set up CPU1 to respond to the wrong
+ * IPI interrupt.
+ * Here we will start up CPU1 in the background and ask it to
+ * reconfigure itself then go back to sleep.
+ */
+ memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
+ __sync();
+ set_c0_cause(C_SW0);
+ cpumask_set_cpu(1, &bmips_booted_mask);
+
+ /*
+ * FIXME: we really should have some sort of hazard barrier here
+ */
+ }
}
void __init prom_free_prom_memory(void)
[BCM63XX_RESET_PCIE] = BCM## __cpu ##_RESET_PCIE, \
[BCM63XX_RESET_PCIE_EXT] = BCM## __cpu ##_RESET_PCIE_EXT,
+#define BCM3368_RESET_SPI SOFTRESET_3368_SPI_MASK
+#define BCM3368_RESET_ENET SOFTRESET_3368_ENET_MASK
+#define BCM3368_RESET_USBH 0
+#define BCM3368_RESET_USBD SOFTRESET_3368_USBS_MASK
+#define BCM3368_RESET_DSL 0
+#define BCM3368_RESET_SAR 0
+#define BCM3368_RESET_EPHY SOFTRESET_3368_EPHY_MASK
+#define BCM3368_RESET_ENETSW 0
+#define BCM3368_RESET_PCM SOFTRESET_3368_PCM_MASK
+#define BCM3368_RESET_MPI SOFTRESET_3368_MPI_MASK
+#define BCM3368_RESET_PCIE 0
+#define BCM3368_RESET_PCIE_EXT 0
+
#define BCM6328_RESET_SPI SOFTRESET_6328_SPI_MASK
#define BCM6328_RESET_ENET 0
#define BCM6328_RESET_USBH SOFTRESET_6328_USBH_MASK
/*
* core reset bits
*/
+static const u32 bcm3368_reset_bits[] = {
+ __GEN_RESET_BITS_TABLE(3368)
+};
+
static const u32 bcm6328_reset_bits[] = {
__GEN_RESET_BITS_TABLE(6328)
};
static int __init bcm63xx_reset_bits_init(void)
{
- if (BCMCPU_IS_6328()) {
+ if (BCMCPU_IS_3368()) {
+ reset_reg = PERF_SOFTRESET_6358_REG;
+ bcm63xx_reset_bits = bcm3368_reset_bits;
+ } else if (BCMCPU_IS_6328()) {
reset_reg = PERF_SOFTRESET_6328_REG;
bcm63xx_reset_bits = bcm6328_reset_bits;
} else if (BCMCPU_IS_6338()) {
}
#else
+#ifdef CONFIG_BCM63XX_CPU_3368
+static const u32 bcm63xx_reset_bits[] = {
+ __GEN_RESET_BITS_TABLE(3368)
+};
+#define reset_reg PERF_SOFTRESET_6358_REG
+#endif
+
#ifdef CONFIG_BCM63XX_CPU_6328
static const u32 bcm63xx_reset_bits[] = {
__GEN_RESET_BITS_TABLE(6328)
/* mask and clear all external irq */
switch (bcm63xx_get_cpu_id()) {
+ case BCM3368_CPU_ID:
+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_3368;
+ break;
case BCM6328_CPU_ID:
perf_regs[0] = PERF_EXTIRQ_CFG_REG_6328;
break;
# Disable Function Tracer
KBUILD_CFLAGS := $(shell echo $(KBUILD_CFLAGS) | sed -e "s/-pg//")
+KBUILD_CFLAGS := $(filter-out -fstack-protector, $(KBUILD_CFLAGS))
+
KBUILD_CFLAGS := $(LINUXINCLUDE) $(KBUILD_CFLAGS) -D__KERNEL__ \
-DBOOT_HEAP_SIZE=$(BOOT_HEAP_SIZE) -D"VMLINUX_LOAD_ADDRESS_ULL=$(VMLINUX_LOAD_ADDRESS)ull"
#define PORT(offset) (UART0_BASE + (4 * offset))
#endif
+#ifdef CONFIG_CPU_XLR
+#define UART0_BASE 0x1EF14000
+#define PORT(offset) (CKSEG1ADDR(UART0_BASE) + (4 * offset))
+#define IOTYPE unsigned int
+#endif
+
+#ifdef CONFIG_CPU_XLP
+#define UART0_BASE 0x18030100
+#define PORT(offset) (CKSEG1ADDR(UART0_BASE) + (4 * offset))
+#define IOTYPE unsigned int
+#endif
+
+#ifndef IOTYPE
+#define IOTYPE char
+#endif
+
#ifndef PORT
#error please define the serial port address for your own machine
#endif
static inline unsigned int serial_in(int offset)
{
- return *((char *)PORT(offset));
+ return *((volatile IOTYPE *)PORT(offset)) & 0xFF;
}
static inline void serial_out(int offset, int value)
{
- *((char *)PORT(offset)) = value;
+ *((volatile IOTYPE *)PORT(offset)) = value & 0xFF;
}
void putc(char c)
{
- int timeout = 1024;
+ int timeout = 1000000;
while (((serial_in(UART_LSR) & UART_LSR_THRE) == 0) && (timeout-- > 0))
;
non-CN63XXP1 hardware, so it is recommended to select "n"
unless it is known the workarounds are needed.
+endif # CPU_CAVIUM_OCTEON
+
+if CAVIUM_OCTEON_SOC
+
config CAVIUM_OCTEON_2ND_KERNEL
bool "Build the kernel to be used as a 2nd kernel on the same chip"
default "n"
with this option to be run at the same time as one built without this
option.
-config CAVIUM_OCTEON_HW_FIX_UNALIGNED
- bool "Enable hardware fixups of unaligned loads and stores"
- default "y"
- help
- Configure the Octeon hardware to automatically fix unaligned loads
- and stores. Normally unaligned accesses are fixed using a kernel
- exception handler. This option enables the hardware automatic fixups,
- which requires only an extra 3 cycles. Disable this option if you
- are running code that relies on address exceptions on unaligned
- accesses.
-
config CAVIUM_OCTEON_CVMSEG_SIZE
int "Number of L1 cache lines reserved for CVMSEG memory"
range 0 54
To compile this driver as a module, choose M here. The module
will be called octeon-ilm
-endif # CPU_CAVIUM_OCTEON
+endif # CAVIUM_OCTEON_SOC
CFLAGS_octeon-platform.o = -I$(src)/../../../scripts/dtc/libfdt
CFLAGS_setup.o = -I$(src)/../../../scripts/dtc/libfdt
-obj-y := cpu.o setup.o serial.o octeon-platform.o octeon-irq.o csrc-octeon.o
-obj-y += dma-octeon.o flash_setup.o
+obj-y := cpu.o setup.o octeon-platform.o octeon-irq.o csrc-octeon.o
+obj-y += dma-octeon.o
obj-y += octeon-memcpy.o
obj-y += executive/
+obj-$(CONFIG_MTD) += flash_setup.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_OCTEON_ILM) += oct_ilm.o
#
# Cavium Octeon
#
-platform-$(CONFIG_CPU_CAVIUM_OCTEON) += cavium-octeon/
-cflags-$(CONFIG_CPU_CAVIUM_OCTEON) += \
+platform-$(CONFIG_CAVIUM_OCTEON_SOC) += cavium-octeon/
+cflags-$(CONFIG_CAVIUM_OCTEON_SOC) += \
-I$(srctree)/arch/mips/include/asm/mach-cavium-octeon
ifdef CONFIG_CAVIUM_OCTEON_2ND_KERNEL
-load-$(CONFIG_CPU_CAVIUM_OCTEON) += 0xffffffff84100000
+load-$(CONFIG_CAVIUM_OCTEON_SOC) += 0xffffffff84100000
else
-load-$(CONFIG_CPU_CAVIUM_OCTEON) += 0xffffffff81100000
+load-$(CONFIG_CAVIUM_OCTEON_SOC) += 0xffffffff81100000
endif
return ipd_port - 16 + 4;
else
return -1;
+ case CVMX_BOARD_TYPE_UBNT_E100:
+ if (ipd_port >= 0 && ipd_port <= 2)
+ return 7 - ipd_port;
+ else
+ return -1;
}
/* Some unknown board. Somebody forgot to update this function... */
}
}
}
+ } else if (cvmx_sysinfo_get()->board_type ==
+ CVMX_BOARD_TYPE_UBNT_E100) {
+ cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(0, interface), 0);
+ cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(0, interface), 0x10);
+ cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(1, interface), 0);
+ cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(1, interface), 0x10);
+ cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(2, interface), 0);
+ cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(2, interface), 0x10);
}
return 0;
}
if (alias_prop) {
uart = fdt_path_offset(initial_boot_params, alias_prop);
- if (uart_mask & (1 << i))
+ if (uart_mask & (1 << i)) {
+ __be32 f;
+
+ f = cpu_to_be32(octeon_get_io_clock_rate());
+ fdt_setprop_inplace(initial_boot_params,
+ uart, "clock-frequency",
+ &f, sizeof(f));
continue;
+ }
pr_debug("Deleting uart%d\n", i);
fdt_nop_node(initial_boot_params, uart);
fdt_nop_property(initial_boot_params, aliases,
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2004-2007 Cavium Networks
- */
-#include <linux/console.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/serial.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_reg.h>
-#include <linux/tty.h>
-#include <linux/irq.h>
-
-#include <asm/time.h>
-
-#include <asm/octeon/octeon.h>
-
-#define DEBUG_UART 1
-
-unsigned int octeon_serial_in(struct uart_port *up, int offset)
-{
- int rv = cvmx_read_csr((uint64_t)(up->membase + (offset << 3)));
- if (offset == UART_IIR && (rv & 0xf) == 7) {
- /* Busy interrupt, read the USR (39) and try again. */
- cvmx_read_csr((uint64_t)(up->membase + (39 << 3)));
- rv = cvmx_read_csr((uint64_t)(up->membase + (offset << 3)));
- }
- return rv;
-}
-
-void octeon_serial_out(struct uart_port *up, int offset, int value)
-{
- /*
- * If bits 6 or 7 of the OCTEON UART's LCR are set, it quits
- * working.
- */
- if (offset == UART_LCR)
- value &= 0x9f;
- cvmx_write_csr((uint64_t)(up->membase + (offset << 3)), (u8)value);
-}
-
-static int octeon_serial_probe(struct platform_device *pdev)
-{
- int irq, res;
- struct resource *res_mem;
- struct uart_8250_port up;
-
- /* All adaptors have an irq. */
- irq = platform_get_irq(pdev, 0);
- if (irq < 0)
- return irq;
-
- memset(&up, 0, sizeof(up));
-
- up.port.flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
- up.port.type = PORT_OCTEON;
- up.port.iotype = UPIO_MEM;
- up.port.regshift = 3;
- up.port.dev = &pdev->dev;
-
- if (octeon_is_simulation())
- /* Make simulator output fast*/
- up.port.uartclk = 115200 * 16;
- else
- up.port.uartclk = octeon_get_io_clock_rate();
-
- up.port.serial_in = octeon_serial_in;
- up.port.serial_out = octeon_serial_out;
- up.port.irq = irq;
-
- res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (res_mem == NULL) {
- dev_err(&pdev->dev, "found no memory resource\n");
- return -ENXIO;
- }
- up.port.mapbase = res_mem->start;
- up.port.membase = ioremap(res_mem->start, resource_size(res_mem));
-
- res = serial8250_register_8250_port(&up);
-
- return res >= 0 ? 0 : res;
-}
-
-static struct of_device_id octeon_serial_match[] = {
- {
- .compatible = "cavium,octeon-3860-uart",
- },
- {},
-};
-MODULE_DEVICE_TABLE(of, octeon_serial_match);
-
-static struct platform_driver octeon_serial_driver = {
- .probe = octeon_serial_probe,
- .driver = {
- .owner = THIS_MODULE,
- .name = "octeon_serial",
- .of_match_table = octeon_serial_match,
- },
-};
-
-static int __init octeon_serial_init(void)
-{
- return platform_driver_register(&octeon_serial_driver);
-}
-late_initcall(octeon_serial_init);
* Copyright (C) 2008, 2009 Wind River Systems
* written by Ralf Baechle <ralf@linux-mips.org>
*/
+#include <linux/compiler.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/console.h>
#include <asm/octeon/pci-octeon.h>
#include <asm/octeon/cvmx-mio-defs.h>
-#ifdef CONFIG_CAVIUM_DECODE_RSL
-extern void cvmx_interrupt_rsl_decode(void);
-extern int __cvmx_interrupt_ecc_report_single_bit_errors;
-extern void cvmx_interrupt_rsl_enable(void);
-#endif
-
extern struct plat_smp_ops octeon_smp_ops;
#ifdef CONFIG_PCI
octeon_kill_core(NULL);
}
-/**
- * Handle all the error condition interrupts that might occur.
- *
- */
-#ifdef CONFIG_CAVIUM_DECODE_RSL
-static irqreturn_t octeon_rlm_interrupt(int cpl, void *dev_id)
-{
- cvmx_interrupt_rsl_decode();
- return IRQ_HANDLED;
-}
-#endif
-
/**
* Return a string representing the system type
*
if (cvmx_read_csr(CVMX_L2D_FUS3) & (3ull << 34)) {
pr_info("Skipping L2 locking due to reduced L2 cache size\n");
} else {
- uint32_t ebase = read_c0_ebase() & 0x3ffff000;
+ uint32_t __maybe_unused ebase = read_c0_ebase() & 0x3ffff000;
#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2_TLB
/* TLB refill */
cvmx_l2c_lock_mem_region(ebase, 0x100);
cvmx_bootmem_unlock();
/* Add the memory region for the kernel. */
kernel_start = (unsigned long) _text;
- kernel_size = ALIGN(_end - _text, 0x100000);
+ kernel_size = _end - _text;
/* Adjust for physical offset. */
kernel_start &= ~0xffffffff80000000ULL;
panic("Core-14449 WAR not in place (%04x).\n"
"Please build kernel with proper options (CONFIG_CAVIUM_CN63XXP1).", insn);
}
-#ifdef CONFIG_CAVIUM_DECODE_RSL
- cvmx_interrupt_rsl_enable();
-
- /* Add an interrupt handler for general failures. */
- if (request_irq(OCTEON_IRQ_RML, octeon_rlm_interrupt, IRQF_SHARED,
- "RML/RSL", octeon_rlm_interrupt)) {
- panic("Unable to request_irq(OCTEON_IRQ_RML)");
- }
-#endif
}
int octeon_prune_device_tree(void);
-CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD=y
+CONFIG_CAVIUM_OCTEON_SOC=y
CONFIG_CAVIUM_CN63XXP1=y
CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE=2
-CONFIG_SPARSEMEM_MANUAL=y
CONFIG_TRANSPARENT_HUGEPAGE=y
CONFIG_SMP=y
CONFIG_NR_CPUS=32
CONFIG_HZ_100=y
CONFIG_PREEMPT=y
-CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_FW_LOADER is not set
CONFIG_MTD=y
# CONFIG_MTD_OF_PARTS is not set
-CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=2
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_DW=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_OCTEON=y
+++ /dev/null
-CONFIG_WR_PPMC=y
-CONFIG_HZ_1000=y
-CONFIG_EXPERIMENTAL=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_EXPERT=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_EPOLL is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-CONFIG_PCI=y
-CONFIG_HOTPLUG_PCI=y
-CONFIG_BINFMT_MISC=y
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_XFRM_MIGRATE=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-CONFIG_IP_MROUTE=y
-CONFIG_ARPD=y
-CONFIG_INET_XFRM_MODE_TRANSPORT=m
-CONFIG_INET_XFRM_MODE_TUNNEL=m
-CONFIG_INET_XFRM_MODE_BEET=m
-CONFIG_TCP_MD5SIG=y
-# CONFIG_IPV6 is not set
-CONFIG_NETWORK_SECMARK=y
-CONFIG_FW_LOADER=m
-CONFIG_BLK_DEV_RAM=y
-CONFIG_SGI_IOC4=m
-CONFIG_NETDEVICES=y
-CONFIG_PHYLIB=y
-CONFIG_VITESSE_PHY=m
-CONFIG_SMSC_PHY=m
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_E100=y
-CONFIG_QLA3XXX=m
-CONFIG_CHELSIO_T3=m
-CONFIG_NETXEN_NIC=m
-# CONFIG_INPUT is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
-# CONFIG_HW_RANDOM is not set
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_DLM=m
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="console=ttyS0,115200n8"
-CONFIG_CRYPTO_NULL=m
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_LRW=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_MD4=m
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_SHA256=m
-CONFIG_CRYPTO_SHA512=m
-CONFIG_CRYPTO_TGR192=m
-CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_ANUBIS=m
-CONFIG_CRYPTO_ARC4=m
-CONFIG_CRYPTO_BLOWFISH=m
-CONFIG_CRYPTO_CAMELLIA=m
-CONFIG_CRYPTO_CAST5=m
-CONFIG_CRYPTO_CAST6=m
-CONFIG_CRYPTO_DES=m
-CONFIG_CRYPTO_FCRYPT=m
-CONFIG_CRYPTO_KHAZAD=m
-CONFIG_CRYPTO_SERPENT=m
-CONFIG_CRYPTO_TEA=m
-CONFIG_CRYPTO_TWOFISH=m
-CONFIG_CRYPTO_DEFLATE=m
-CONFIG_CRC_CCITT=y
-CONFIG_CRC16=y
-CONFIG_LIBCRC32C=y
obj-y := ecc-berr.o int-handler.o ioasic-irq.o kn01-berr.o \
kn02-irq.o kn02xa-berr.o reset.o setup.o time.o
-obj-$(CONFIG_PROM_CONSOLE) += promcon.o
obj-$(CONFIG_TC) += tc.o
obj-$(CONFIG_CPU_HAS_WB) += wbflush.o
+++ /dev/null
-/*
- * Wrap-around code for a console using the
- * DECstation PROM io-routines.
- *
- * Copyright (c) 1998 Harald Koerfgen
- */
-
-#include <linux/tty.h>
-#include <linux/ptrace.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/fs.h>
-
-#include <asm/dec/prom.h>
-
-static void prom_console_write(struct console *co, const char *s,
- unsigned count)
-{
- unsigned i;
-
- /*
- * Now, do each character
- */
- for (i = 0; i < count; i++) {
- if (*s == 10)
- prom_printf("%c", 13);
- prom_printf("%c", *s++);
- }
-}
-
-static int __init prom_console_setup(struct console *co, char *options)
-{
- return 0;
-}
-
-static struct console sercons = {
- .name = "ttyS",
- .write = prom_console_write,
- .setup = prom_console_setup,
- .flags = CON_PRINTBUFFER,
- .index = -1,
-};
-
-/*
- * Register console.
- */
-
-static int __init prom_console_init(void)
-{
- register_console(&sercons);
-
- return 0;
-}
-console_initcall(prom_console_init);
return xiocb.xiocb_status;
}
-int cfe_write(int handle, unsigned char *buffer, int length)
+int cfe_write(int handle, const char *buffer, int length)
{
return cfe_writeblk(handle, 0, buffer, length);
}
-int cfe_writeblk(int handle, s64 offset, unsigned char *buffer, int length)
+int cfe_writeblk(int handle, s64 offset, const char *buffer, int length)
{
struct cfe_xiocb xiocb;
#include <linux/notifier.h>
+#if defined(CONFIG_CPU_CAVIUM_OCTEON)
+
+extern void octeon_cop2_save(struct octeon_cop2_state *);
+extern void octeon_cop2_restore(struct octeon_cop2_state *);
+
+#define cop2_save(r) octeon_cop2_save(r)
+#define cop2_restore(r) octeon_cop2_restore(r)
+
+#define cop2_present 1
+#define cop2_lazy_restore 1
+
+#elif defined(CONFIG_CPU_XLP)
+
+extern void nlm_cop2_save(struct nlm_cop2_state *);
+extern void nlm_cop2_restore(struct nlm_cop2_state *);
+#define cop2_save(r) nlm_cop2_save(r)
+#define cop2_restore(r) nlm_cop2_restore(r)
+
+#define cop2_present 1
+#define cop2_lazy_restore 0
+
+#else
+
+#define cop2_present 0
+#define cop2_lazy_restore 0
+#define cop2_save(r)
+#define cop2_restore(r)
+#endif
+
enum cu2_ops {
CU2_EXCEPTION,
CU2_LWC2_OP,
#ifndef cpu_has_tlb
#define cpu_has_tlb (cpu_data[0].options & MIPS_CPU_TLB)
#endif
+
+/*
+ * For the moment we don't consider R6000 and R8000 so we can assume that
+ * anything that doesn't support R4000-style exceptions and interrupts is
+ * R3000-like. Users should still treat these two macro definitions as
+ * opaque.
+ */
+#ifndef cpu_has_3kex
+#define cpu_has_3kex (!cpu_has_4kex)
+#endif
#ifndef cpu_has_4kex
#define cpu_has_4kex (cpu_data[0].options & MIPS_CPU_4KEX)
#endif
#define cpu_has_mips16 (cpu_data[0].ases & MIPS_ASE_MIPS16)
#endif
#ifndef cpu_has_mdmx
-#define cpu_has_mdmx (cpu_data[0].ases & MIPS_ASE_MDMX)
+#define cpu_has_mdmx (cpu_data[0].ases & MIPS_ASE_MDMX)
#endif
#ifndef cpu_has_mips3d
-#define cpu_has_mips3d (cpu_data[0].ases & MIPS_ASE_MIPS3D)
+#define cpu_has_mips3d (cpu_data[0].ases & MIPS_ASE_MIPS3D)
#endif
#ifndef cpu_has_smartmips
-#define cpu_has_smartmips (cpu_data[0].ases & MIPS_ASE_SMARTMIPS)
+#define cpu_has_smartmips (cpu_data[0].ases & MIPS_ASE_SMARTMIPS)
#endif
#ifndef cpu_has_rixi
#define cpu_has_rixi (cpu_data[0].options & MIPS_CPU_RIXI)
#endif
#ifndef cpu_has_mmips
-#define cpu_has_mmips (cpu_data[0].options & MIPS_CPU_MICROMIPS)
+# ifdef CONFIG_SYS_SUPPORTS_MICROMIPS
+# define cpu_has_mmips (cpu_data[0].options & MIPS_CPU_MICROMIPS)
+# else
+# define cpu_has_mmips 0
+# endif
#endif
#ifndef cpu_has_vtag_icache
#define cpu_has_vtag_icache (cpu_data[0].icache.flags & MIPS_CACHE_VTAG)
#define cpu_has_ic_fills_f_dc (cpu_data[0].icache.flags & MIPS_CACHE_IC_F_DC)
#endif
#ifndef cpu_has_pindexed_dcache
-#define cpu_has_pindexed_dcache (cpu_data[0].dcache.flags & MIPS_CACHE_PINDEX)
+#define cpu_has_pindexed_dcache (cpu_data[0].dcache.flags & MIPS_CACHE_PINDEX)
#endif
#ifndef cpu_has_local_ebase
#define cpu_has_local_ebase 1
#endif
#endif
-# define cpu_has_mips_1 (cpu_data[0].isa_level & MIPS_CPU_ISA_I)
#ifndef cpu_has_mips_2
# define cpu_has_mips_2 (cpu_data[0].isa_level & MIPS_CPU_ISA_II)
#endif
#ifndef cpu_has_mips_5
# define cpu_has_mips_5 (cpu_data[0].isa_level & MIPS_CPU_ISA_V)
#endif
-# ifndef cpu_has_mips32r1
+#ifndef cpu_has_mips32r1
# define cpu_has_mips32r1 (cpu_data[0].isa_level & MIPS_CPU_ISA_M32R1)
-# endif
-# ifndef cpu_has_mips32r2
+#endif
+#ifndef cpu_has_mips32r2
# define cpu_has_mips32r2 (cpu_data[0].isa_level & MIPS_CPU_ISA_M32R2)
-# endif
-# ifndef cpu_has_mips64r1
+#endif
+#ifndef cpu_has_mips64r1
# define cpu_has_mips64r1 (cpu_data[0].isa_level & MIPS_CPU_ISA_M64R1)
-# endif
-# ifndef cpu_has_mips64r2
+#endif
+#ifndef cpu_has_mips64r2
# define cpu_has_mips64r2 (cpu_data[0].isa_level & MIPS_CPU_ISA_M64R2)
-# endif
+#endif
/*
* Shortcuts ...
* has CLO and CLZ but not DCLO nor DCLZ. For 64-bit kernels
* cpu_has_clo_clz also indicates the availability of DCLO and DCLZ.
*/
-# ifndef cpu_has_clo_clz
-# define cpu_has_clo_clz cpu_has_mips_r
-# endif
+#ifndef cpu_has_clo_clz
+#define cpu_has_clo_clz cpu_has_mips_r
+#endif
#ifndef cpu_has_dsp
#define cpu_has_dsp (cpu_data[0].ases & MIPS_ASE_DSP)
# define cpu_has_64bits (cpu_data[0].isa_level & MIPS_CPU_ISA_64BIT)
# endif
# ifndef cpu_has_64bit_zero_reg
-# define cpu_has_64bit_zero_reg (cpu_data[0].isa_level & MIPS_CPU_ISA_64BIT)
+# define cpu_has_64bit_zero_reg (cpu_data[0].isa_level & MIPS_CPU_ISA_64BIT)
# endif
# ifndef cpu_has_64bit_gp_regs
# define cpu_has_64bit_gp_regs 0
* ISA Level encodings
*
*/
-#define MIPS_CPU_ISA_I 0x00000001
-#define MIPS_CPU_ISA_II 0x00000002
-#define MIPS_CPU_ISA_III 0x00000004
-#define MIPS_CPU_ISA_IV 0x00000008
-#define MIPS_CPU_ISA_V 0x00000010
-#define MIPS_CPU_ISA_M32R1 0x00000020
-#define MIPS_CPU_ISA_M32R2 0x00000040
-#define MIPS_CPU_ISA_M64R1 0x00000080
-#define MIPS_CPU_ISA_M64R2 0x00000100
-
-#define MIPS_CPU_ISA_32BIT (MIPS_CPU_ISA_I | MIPS_CPU_ISA_II | \
- MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M32R2)
+#define MIPS_CPU_ISA_II 0x00000001
+#define MIPS_CPU_ISA_III 0x00000002
+#define MIPS_CPU_ISA_IV 0x00000004
+#define MIPS_CPU_ISA_V 0x00000008
+#define MIPS_CPU_ISA_M32R1 0x00000010
+#define MIPS_CPU_ISA_M32R2 0x00000020
+#define MIPS_CPU_ISA_M64R1 0x00000040
+#define MIPS_CPU_ISA_M64R2 0x00000080
+
+#define MIPS_CPU_ISA_32BIT (MIPS_CPU_ISA_II | MIPS_CPU_ISA_M32R1 | \
+ MIPS_CPU_ISA_M32R2)
#define MIPS_CPU_ISA_64BIT (MIPS_CPU_ISA_III | MIPS_CPU_ISA_IV | \
MIPS_CPU_ISA_V | MIPS_CPU_ISA_M64R1 | MIPS_CPU_ISA_M64R2)
int cfe_readblk(int handle, int64_t offset, unsigned char *buffer,
int length);
int cfe_setenv(char *name, char *val);
-int cfe_write(int handle, unsigned char *buffer, int length);
-int cfe_writeblk(int handle, int64_t offset, unsigned char *buffer,
+int cfe_write(int handle, const char *buffer, int length);
+int cfe_writeblk(int handle, int64_t offset, const char *buffer,
int length);
#endif /* CFE_API_H */
#define GIC_CPU_INT2 2 /* . */
#define GIC_CPU_INT3 3 /* . */
#define GIC_CPU_INT4 4 /* . */
-#define GIC_CPU_INT5 5 /* Core Interrupt 5 */
+#define GIC_CPU_INT5 5 /* Core Interrupt 7 */
/* Local GIC interrupts. */
#define GIC_INT_TMR (GIC_CPU_INT5)
extern void __iomem * __ioremap(phys_t offset, phys_t size, unsigned long flags);
extern void __iounmap(const volatile void __iomem *addr);
+#ifndef CONFIG_PCI
+struct pci_dev;
+static inline void pci_iounmap(struct pci_dev *dev, void __iomem *addr) {}
+#endif
+
static inline void __iomem * __ioremap_mode(phys_t offset, unsigned long size,
unsigned long flags)
{
#define readl_relaxed readl
#define readq_relaxed readq
+#define writeb_relaxed writeb
+#define writew_relaxed writew
+#define writel_relaxed writel
+#define writeq_relaxed writeq
+
#define readb_be(addr) \
__raw_readb((__force unsigned *)(addr))
#define readw_be(addr) \
+++ /dev/null
-/*
- * Copyright (C) 2005 MIPS Technologies, Inc. All rights reserved.
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- */
-
-#ifndef _ASM_KSPD_H
-#define _ASM_KSPD_H
-
-struct kspd_notifications {
- void (*kspd_sp_exit)(int sp_id);
-
- struct list_head list;
-};
-
-static inline void kspd_notify(struct kspd_notifications *notify)
-{
-}
-
-#endif
* This handles the memory map.
* We handle pages at KSEG0 for kernels with 32 bit address space.
*/
-#define PAGE_OFFSET 0x94000000UL
-#define PHYS_OFFSET 0x14000000UL
+#define PAGE_OFFSET _AC(0x94000000, UL)
+#define PHYS_OFFSET _AC(0x14000000, UL)
+
+#define UNCAC_BASE _AC(0xb4000000, UL) /* 0xa0000000 + PHYS_OFFSET */
+#define IO_BASE UNCAC_BASE
#include <asm/mach-generic/spaces.h>
* compile time if only one CPU support is enabled (idea stolen from
* arm mach-types)
*/
+#define BCM3368_CPU_ID 0x3368
#define BCM6328_CPU_ID 0x6328
#define BCM6338_CPU_ID 0x6338
#define BCM6345_CPU_ID 0x6345
u8 bcm63xx_get_cpu_rev(void);
unsigned int bcm63xx_get_cpu_freq(void);
+#ifdef CONFIG_BCM63XX_CPU_3368
+# ifdef bcm63xx_get_cpu_id
+# undef bcm63xx_get_cpu_id
+# define bcm63xx_get_cpu_id() __bcm63xx_get_cpu_id()
+# define BCMCPU_RUNTIME_DETECT
+# else
+# define bcm63xx_get_cpu_id() BCM3368_CPU_ID
+# endif
+# define BCMCPU_IS_3368() (bcm63xx_get_cpu_id() == BCM3368_CPU_ID)
+#else
+# define BCMCPU_IS_3368() (0)
+#endif
+
#ifdef CONFIG_BCM63XX_CPU_6328
# ifdef bcm63xx_get_cpu_id
# undef bcm63xx_get_cpu_id
#define RSET_XTMDMAS_SIZE(chans) (16 * (chans))
#define RSET_RNG_SIZE 20
+/*
+ * 3368 register sets base address
+ */
+#define BCM_3368_DSL_LMEM_BASE (0xdeadbeef)
+#define BCM_3368_PERF_BASE (0xfff8c000)
+#define BCM_3368_TIMER_BASE (0xfff8c040)
+#define BCM_3368_WDT_BASE (0xfff8c080)
+#define BCM_3368_UART0_BASE (0xfff8c100)
+#define BCM_3368_UART1_BASE (0xfff8c120)
+#define BCM_3368_GPIO_BASE (0xfff8c080)
+#define BCM_3368_SPI_BASE (0xfff8c800)
+#define BCM_3368_HSSPI_BASE (0xdeadbeef)
+#define BCM_3368_UDC0_BASE (0xdeadbeef)
+#define BCM_3368_USBDMA_BASE (0xdeadbeef)
+#define BCM_3368_OHCI0_BASE (0xdeadbeef)
+#define BCM_3368_OHCI_PRIV_BASE (0xdeadbeef)
+#define BCM_3368_USBH_PRIV_BASE (0xdeadbeef)
+#define BCM_3368_USBD_BASE (0xdeadbeef)
+#define BCM_3368_MPI_BASE (0xfff80000)
+#define BCM_3368_PCMCIA_BASE (0xfff80054)
+#define BCM_3368_PCIE_BASE (0xdeadbeef)
+#define BCM_3368_SDRAM_REGS_BASE (0xdeadbeef)
+#define BCM_3368_DSL_BASE (0xdeadbeef)
+#define BCM_3368_UBUS_BASE (0xdeadbeef)
+#define BCM_3368_ENET0_BASE (0xfff98000)
+#define BCM_3368_ENET1_BASE (0xfff98800)
+#define BCM_3368_ENETDMA_BASE (0xfff99800)
+#define BCM_3368_ENETDMAC_BASE (0xfff99900)
+#define BCM_3368_ENETDMAS_BASE (0xfff99a00)
+#define BCM_3368_ENETSW_BASE (0xdeadbeef)
+#define BCM_3368_EHCI0_BASE (0xdeadbeef)
+#define BCM_3368_SDRAM_BASE (0xdeadbeef)
+#define BCM_3368_MEMC_BASE (0xfff84000)
+#define BCM_3368_DDR_BASE (0xdeadbeef)
+#define BCM_3368_M2M_BASE (0xdeadbeef)
+#define BCM_3368_ATM_BASE (0xdeadbeef)
+#define BCM_3368_XTM_BASE (0xdeadbeef)
+#define BCM_3368_XTMDMA_BASE (0xdeadbeef)
+#define BCM_3368_XTMDMAC_BASE (0xdeadbeef)
+#define BCM_3368_XTMDMAS_BASE (0xdeadbeef)
+#define BCM_3368_PCM_BASE (0xfff9c200)
+#define BCM_3368_PCMDMA_BASE (0xdeadbeef)
+#define BCM_3368_PCMDMAC_BASE (0xdeadbeef)
+#define BCM_3368_PCMDMAS_BASE (0xdeadbeef)
+#define BCM_3368_RNG_BASE (0xdeadbeef)
+#define BCM_3368_MISC_BASE (0xdeadbeef)
+
/*
* 6328 register sets base address
*/
#define BCM_6328_PCMDMAS_BASE (0xdeadbeef)
#define BCM_6328_RNG_BASE (0xdeadbeef)
#define BCM_6328_MISC_BASE (0xb0001800)
+#define BCM_6328_OTP_BASE (0xb0000600)
+
/*
* 6338 register sets base address
*/
#ifdef BCMCPU_RUNTIME_DETECT
return bcm63xx_regs_base[set];
#else
+#ifdef CONFIG_BCM63XX_CPU_3368
+ __GEN_RSET(3368)
+#endif
#ifdef CONFIG_BCM63XX_CPU_6328
__GEN_RSET(6328)
#endif
IRQ_XTM_DMA0,
};
+/*
+ * 3368 irqs
+ */
+#define BCM_3368_TIMER_IRQ (IRQ_INTERNAL_BASE + 0)
+#define BCM_3368_SPI_IRQ (IRQ_INTERNAL_BASE + 1)
+#define BCM_3368_UART0_IRQ (IRQ_INTERNAL_BASE + 2)
+#define BCM_3368_UART1_IRQ (IRQ_INTERNAL_BASE + 3)
+#define BCM_3368_DSL_IRQ 0
+#define BCM_3368_UDC0_IRQ 0
+#define BCM_3368_OHCI0_IRQ 0
+#define BCM_3368_ENET0_IRQ (IRQ_INTERNAL_BASE + 8)
+#define BCM_3368_ENET1_IRQ (IRQ_INTERNAL_BASE + 6)
+#define BCM_3368_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9)
+#define BCM_3368_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 15)
+#define BCM_3368_ENET0_TXDMA_IRQ (IRQ_INTERNAL_BASE + 16)
+#define BCM_3368_HSSPI_IRQ 0
+#define BCM_3368_EHCI0_IRQ 0
+#define BCM_3368_USBD_IRQ 0
+#define BCM_3368_USBD_RXDMA0_IRQ 0
+#define BCM_3368_USBD_TXDMA0_IRQ 0
+#define BCM_3368_USBD_RXDMA1_IRQ 0
+#define BCM_3368_USBD_TXDMA1_IRQ 0
+#define BCM_3368_USBD_RXDMA2_IRQ 0
+#define BCM_3368_USBD_TXDMA2_IRQ 0
+#define BCM_3368_ENET1_RXDMA_IRQ (IRQ_INTERNAL_BASE + 17)
+#define BCM_3368_ENET1_TXDMA_IRQ (IRQ_INTERNAL_BASE + 18)
+#define BCM_3368_PCI_IRQ (IRQ_INTERNAL_BASE + 31)
+#define BCM_3368_PCMCIA_IRQ 0
+#define BCM_3368_ATM_IRQ 0
+#define BCM_3368_ENETSW_RXDMA0_IRQ 0
+#define BCM_3368_ENETSW_RXDMA1_IRQ 0
+#define BCM_3368_ENETSW_RXDMA2_IRQ 0
+#define BCM_3368_ENETSW_RXDMA3_IRQ 0
+#define BCM_3368_ENETSW_TXDMA0_IRQ 0
+#define BCM_3368_ENETSW_TXDMA1_IRQ 0
+#define BCM_3368_ENETSW_TXDMA2_IRQ 0
+#define BCM_3368_ENETSW_TXDMA3_IRQ 0
+#define BCM_3368_XTM_IRQ 0
+#define BCM_3368_XTM_DMA0_IRQ 0
+
+#define BCM_3368_EXT_IRQ0 (IRQ_INTERNAL_BASE + 25)
+#define BCM_3368_EXT_IRQ1 (IRQ_INTERNAL_BASE + 26)
+#define BCM_3368_EXT_IRQ2 (IRQ_INTERNAL_BASE + 27)
+#define BCM_3368_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28)
+
+
/*
* 6328 irqs
*/
switch (bcm63xx_get_cpu_id()) {
case BCM6328_CPU_ID:
return 32;
+ case BCM3368_CPU_ID:
case BCM6358_CPU_ID:
return 40;
case BCM6338_CPU_ID:
/* Clock Control register */
#define PERF_CKCTL_REG 0x4
+#define CKCTL_3368_MAC_EN (1 << 3)
+#define CKCTL_3368_TC_EN (1 << 5)
+#define CKCTL_3368_US_TOP_EN (1 << 6)
+#define CKCTL_3368_DS_TOP_EN (1 << 7)
+#define CKCTL_3368_APM_EN (1 << 8)
+#define CKCTL_3368_SPI_EN (1 << 9)
+#define CKCTL_3368_USBS_EN (1 << 10)
+#define CKCTL_3368_BMU_EN (1 << 11)
+#define CKCTL_3368_PCM_EN (1 << 12)
+#define CKCTL_3368_NTP_EN (1 << 13)
+#define CKCTL_3368_ACP_B_EN (1 << 14)
+#define CKCTL_3368_ACP_A_EN (1 << 15)
+#define CKCTL_3368_EMUSB_EN (1 << 17)
+#define CKCTL_3368_ENET0_EN (1 << 18)
+#define CKCTL_3368_ENET1_EN (1 << 19)
+#define CKCTL_3368_USBU_EN (1 << 20)
+#define CKCTL_3368_EPHY_EN (1 << 21)
+
+#define CKCTL_3368_ALL_SAFE_EN (CKCTL_3368_MAC_EN | \
+ CKCTL_3368_TC_EN | \
+ CKCTL_3368_US_TOP_EN | \
+ CKCTL_3368_DS_TOP_EN | \
+ CKCTL_3368_APM_EN | \
+ CKCTL_3368_SPI_EN | \
+ CKCTL_3368_USBS_EN | \
+ CKCTL_3368_BMU_EN | \
+ CKCTL_3368_PCM_EN | \
+ CKCTL_3368_NTP_EN | \
+ CKCTL_3368_ACP_B_EN | \
+ CKCTL_3368_ACP_A_EN | \
+ CKCTL_3368_EMUSB_EN | \
+ CKCTL_3368_USBU_EN)
+
#define CKCTL_6328_PHYMIPS_EN (1 << 0)
#define CKCTL_6328_ADSL_QPROC_EN (1 << 1)
#define CKCTL_6328_ADSL_AFE_EN (1 << 2)
#define SYS_PLL_SOFT_RESET 0x1
/* Interrupt Mask register */
+#define PERF_IRQMASK_3368_REG 0xc
#define PERF_IRQMASK_6328_REG 0x20
#define PERF_IRQMASK_6338_REG 0xc
#define PERF_IRQMASK_6345_REG 0xc
#define PERF_IRQMASK_6368_REG 0x20
/* Interrupt Status register */
+#define PERF_IRQSTAT_3368_REG 0x10
#define PERF_IRQSTAT_6328_REG 0x28
#define PERF_IRQSTAT_6338_REG 0x10
#define PERF_IRQSTAT_6345_REG 0x10
#define PERF_IRQSTAT_6368_REG 0x28
/* External Interrupt Configuration register */
+#define PERF_EXTIRQ_CFG_REG_3368 0x14
#define PERF_EXTIRQ_CFG_REG_6328 0x18
#define PERF_EXTIRQ_CFG_REG_6338 0x14
#define PERF_EXTIRQ_CFG_REG_6345 0x14
#define PERF_SOFTRESET_6362_REG 0x10
#define PERF_SOFTRESET_6368_REG 0x10
+#define SOFTRESET_3368_SPI_MASK (1 << 0)
+#define SOFTRESET_3368_ENET_MASK (1 << 2)
+#define SOFTRESET_3368_MPI_MASK (1 << 3)
+#define SOFTRESET_3368_EPHY_MASK (1 << 6)
+#define SOFTRESET_3368_USBS_MASK (1 << 11)
+#define SOFTRESET_3368_PCM_MASK (1 << 13)
+
#define SOFTRESET_6328_SPI_MASK (1 << 0)
#define SOFTRESET_6328_EPHY_MASK (1 << 1)
#define SOFTRESET_6328_SAR_MASK (1 << 2)
#define SPI_6348_RX_DATA 0x80
#define SPI_6348_RX_DATA_SIZE 0x3f
-/* BCM 6358/6262/6368 SPI core */
+/* BCM 3368/6358/6262/6368 SPI core */
#define SPI_6358_MSG_CTL 0x00 /* 16-bits register */
#define SPI_6358_MSG_CTL_WIDTH 16
#define SPI_6358_MSG_DATA 0x02
#define PCIE_DEVICE_OFFSET 0x8000
+/*************************************************************************
+ * _REG relative to RSET_OTP
+ *************************************************************************/
+
+#define OTP_USER_BITS_6328_REG(i) (0x20 + (i) * 4)
+#define OTP_6328_REG3_TP1_DISABLED BIT(9)
+
#endif /* BCM63XX_REGS_H_ */
/* GPIO LEDs */
struct gpio_led leds[5];
+
+ /* External PHY reset GPIO */
+ unsigned int ephy_reset_gpio;
+
+ /* External PHY reset GPIO flags from gpio.h */
+ unsigned long ephy_reset_gpio_flags;
};
#endif /* ! BOARD_BCM963XX_H_ */
static inline int is_bcm63xx_internal_registers(phys_t offset)
{
switch (bcm63xx_get_cpu_id()) {
+ case BCM3368_CPU_ID:
+ if (offset >= 0xfff80000)
+ return 1;
+ break;
case BCM6338_CPU_ID:
case BCM6345_CPU_ID:
case BCM6348_CPU_ID:
#ifndef __ASM_MACH_CAVIUM_OCTEON_DMA_COHERENCE_H
#define __ASM_MACH_CAVIUM_OCTEON_DMA_COHERENCE_H
+#include <linux/bug.h>
+
struct device;
extern void octeon_pci_dma_init(void);
size_t size)
{
BUG();
+ return 0;
}
static inline dma_addr_t plat_map_dma_mem_page(struct device *dev,
struct page *page)
{
BUG();
+ return 0;
}
static inline unsigned long plat_dma_addr_to_phys(struct device *dev,
dma_addr_t dma_addr)
{
BUG();
+ return 0;
}
static inline void plat_unmap_dma_mem(struct device *dev, dma_addr_t dma_addr,
static inline int plat_dma_supported(struct device *dev, u64 mask)
{
BUG();
+ return 0;
}
static inline void plat_extra_sync_for_device(struct device *dev)
dma_addr_t dma_addr)
{
BUG();
+ return 0;
}
dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr);
ori v0, CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE
dmtc0 v0, CP0_CVMMEMCTL_REG # Write the cavium mem control register
dmfc0 v0, CP0_CVMCTL_REG # Read the cavium control register
-#ifdef CONFIG_CAVIUM_OCTEON_HW_FIX_UNALIGNED
# Disable unaligned load/store support but leave HW fixup enabled
+ # Needed for octeon specific memcpy
or v0, v0, 0x5001
xor v0, v0, 0x1001
-#else
- # Disable unaligned load/store and HW fixup support
- or v0, v0, 0x5001
- xor v0, v0, 0x5001
-#endif
# Read the processor ID register
mfc0 v1, CP0_PRID_REG
# Disable instruction prefetching (Octeon Pass1 errata)
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 Cavium, Inc.
+ */
+#ifndef _ASM_MACH_CAVIUM_OCTEON_SPACES_H
+#define _ASM_MACH_CAVIUM_OCTEON_SPACES_H
+
+#include <linux/const.h>
+
+#ifdef CONFIG_64BIT
+/* They are all the same and some OCTEON II cores cannot handle 0xa8.. */
+#define CAC_BASE _AC(0x8000000000000000, UL)
+#define UNCAC_BASE _AC(0x8000000000000000, UL)
+#define IO_BASE _AC(0x8000000000000000, UL)
+
+
+#endif /* CONFIG_64BIT */
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* _ASM_MACH_CAVIUM_OCTEON_SPACES_H */
#endif
}
+#ifdef CONFIG_SWIOTLB
+static inline dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+ return paddr;
+}
+
+static inline phys_addr_t dma_to_phys(struct device *dev, dma_addr_t daddr)
+{
+ return daddr;
+}
+#endif
+
#endif /* __ASM_MACH_GENERIC_DMA_COHERENCE_H */
/* Intentionally empty macro, used in head.S. Override in
* arch/mips/mach-xxx/kernel-entry-init.h when necessary.
*/
-.macro kernel_entry_setup
-.endm
+ .macro kernel_entry_setup
+ .endm
/*
* Do SMP slave processor setup necessary before we can savely execute C code.
dsrl \res, NSRI_NODEID_SHFT
.endm
+/*
+ * TLB bits
+ */
+#define PAGE_GLOBAL (1 << 6)
+#define PAGE_VALID (1 << 7)
+#define PAGE_DIRTY (1 << 8)
+#define CACHE_CACHABLE_COW (5 << 9)
+
+ /*
+ * inputs are the text nasid in t1, data nasid in t2.
+ */
+ .macro MAPPED_KERNEL_SETUP_TLB
+#ifdef CONFIG_MAPPED_KERNEL
+ /*
+ * This needs to read the nasid - assume 0 for now.
+ * Drop in 0xffffffffc0000000 in tlbhi, 0+VG in tlblo_0,
+ * 0+DVG in tlblo_1.
+ */
+ dli t0, 0xffffffffc0000000
+ dmtc0 t0, CP0_ENTRYHI
+ li t0, 0x1c000 # Offset of text into node memory
+ dsll t1, NASID_SHFT # Shift text nasid into place
+ dsll t2, NASID_SHFT # Same for data nasid
+ or t1, t1, t0 # Physical load address of kernel text
+ or t2, t2, t0 # Physical load address of kernel data
+ dsrl t1, 12 # 4K pfn
+ dsrl t2, 12 # 4K pfn
+ dsll t1, 6 # Get pfn into place
+ dsll t2, 6 # Get pfn into place
+ li t0, ((PAGE_GLOBAL | PAGE_VALID | CACHE_CACHABLE_COW) >> 6)
+ or t0, t0, t1
+ mtc0 t0, CP0_ENTRYLO0 # physaddr, VG, cach exlwr
+ li t0, ((PAGE_GLOBAL | PAGE_VALID | PAGE_DIRTY | CACHE_CACHABLE_COW) >> 6)
+ or t0, t0, t2
+ mtc0 t0, CP0_ENTRYLO1 # physaddr, DVG, cach exlwr
+ li t0, 0x1ffe000 # MAPPED_KERN_TLBMASK, TLBPGMASK_16M
+ mtc0 t0, CP0_PAGEMASK
+ li t0, 0 # KMAP_INX
+ mtc0 t0, CP0_INDEX
+ li t0, 1
+ mtc0 t0, CP0_WIRED
+ tlbwi
+#else
+ mtc0 zero, CP0_WIRED
+#endif
+ .endm
+
/*
* Intentionally empty macro, used in head.S. Override in
* arch/mips/mach-xxx/kernel-entry-init.h when necessary.
#ifndef _ASM_MACH_IP28_SPACES_H
#define _ASM_MACH_IP28_SPACES_H
-#define CAC_BASE 0xa800000000000000
+#define CAC_BASE _AC(0xa800000000000000, UL)
-#define HIGHMEM_START (~0UL)
+#define HIGHMEM_START (~0UL)
-#define PHYS_OFFSET _AC(0x20000000, UL)
+#define PHYS_OFFSET _AC(0x20000000, UL)
+
+#define UNCAC_BASE _AC(0xc0000000, UL) /* 0xa0000000 + PHYS_OFFSET */
+#define IO_BASE UNCAC_BASE
#include <asm/mach-generic/spaces.h>
+++ /dev/null
-/*
- * include/asm-mips/pmc-sierra/msp71xx/gpio.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * @author Patrick Glass <patrickglass@gmail.com>
- */
-
-#ifndef __PMC_MSP71XX_GPIO_H
-#define __PMC_MSP71XX_GPIO_H
-
-/* Max number of gpio's is 28 on chip plus 3 banks of I2C IO Expanders */
-#define ARCH_NR_GPIOS (28 + (3 * 8))
-
-/* new generic GPIO API - see Documentation/gpio.txt */
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
-/* Setup calls for the gpio and gpio extended */
-extern void msp71xx_init_gpio(void);
-extern void msp71xx_init_gpio_extended(void);
-extern int msp71xx_set_output_drive(unsigned gpio, int value);
-
-/* Custom output drive functionss */
-static inline int gpio_set_output_drive(unsigned gpio, int value)
-{
- return msp71xx_set_output_drive(gpio, value);
-}
-
-/* IRQ's are not supported for gpio lines */
-static inline int gpio_to_irq(unsigned gpio)
-{
- return -EINVAL;
-}
-
-static inline int irq_to_gpio(unsigned irq)
-{
- return -EINVAL;
-}
-
-#endif /* __PMC_MSP71XX_GPIO_H */
+++ /dev/null
-/*
- * This is a direct copy of the ev96100.h file, with a global
- * search and replace. The numbers are the same.
- *
- * The reason I'm duplicating this is so that the 64120/96100
- * defines won't be confusing in the source code.
- */
-#ifndef __ASM_MIPS_GT64120_H
-#define __ASM_MIPS_GT64120_H
-
-/*
- * This is the CPU physical memory map of PPMC Board:
- *
- * 0x00000000-0x03FFFFFF - 64MB SDRAM (SCS[0]#)
- * 0x1C000000-0x1C000000 - LED (CS0)
- * 0x1C800000-0x1C800007 - UART 16550 port (CS1)
- * 0x1F000000-0x1F000000 - MailBox (CS3)
- * 0x1FC00000-0x20000000 - 4MB Flash (BOOT CS)
- */
-
-#define WRPPMC_SDRAM_SCS0_BASE 0x00000000
-#define WRPPMC_SDRAM_SCS0_SIZE 0x04000000
-
-#define WRPPMC_UART16550_BASE 0x1C800000
-#define WRPPMC_UART16550_CLOCK 3686400 /* 3.68MHZ */
-
-#define WRPPMC_LED_BASE 0x1C000000
-#define WRPPMC_MBOX_BASE 0x1F000000
-
-#define WRPPMC_BOOTROM_BASE 0x1FC00000
-#define WRPPMC_BOOTROM_SIZE 0x00400000 /* 4M Flash */
-
-#define WRPPMC_MIPS_TIMER_IRQ 7 /* MIPS compare/count timer interrupt */
-#define WRPPMC_UART16550_IRQ 6
-#define WRPPMC_PCI_INTA_IRQ 3
-
-/*
- * PCI Bus I/O and Memory resources allocation
- *
- * NOTE: We only have PCI_0 hose interface
- */
-#define GT_PCI_MEM_BASE 0x13000000UL
-#define GT_PCI_MEM_SIZE 0x02000000UL
-#define GT_PCI_IO_BASE 0x11000000UL
-#define GT_PCI_IO_SIZE 0x02000000UL
-
-/*
- * PCI interrupts will come in on either the INTA or INTD interrupt lines,
- * which are mapped to the #2 and #5 interrupt pins of the MIPS. On our
- * boards, they all either come in on IntD or they all come in on IntA, they
- * aren't mixed. There can be numerous PCI interrupts, so we keep a list of the
- * "requested" interrupt numbers and go through the list whenever we get an
- * IntA/D.
- *
- * Interrupts < 8 are directly wired to the processor; PCI INTA is 8 and
- * INTD is 11.
- */
-#define GT_TIMER 4
-#define GT_INTA 2
-#define GT_INTD 5
-
-#ifndef __ASSEMBLY__
-
-/*
- * GT64120 internal register space base address
- */
-extern unsigned long gt64120_base;
-
-#define GT64120_BASE (gt64120_base)
-
-/* define WRPPMC_EARLY_DEBUG to enable early output something to UART */
-#undef WRPPMC_EARLY_DEBUG
-
-#ifdef WRPPMC_EARLY_DEBUG
-extern void wrppmc_led_on(int mask);
-extern void wrppmc_led_off(int mask);
-extern void wrppmc_early_printk(const char *fmt, ...);
-#else
-#define wrppmc_early_printk(fmt, ...) do {} while (0)
-#endif /* WRPPMC_EARLY_DEBUG */
-
-#endif /* __ASSEMBLY__ */
-#endif /* __ASM_MIPS_GT64120_H */
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <ralf@linux-mips.org>
- */
-#ifndef __ASM_MIPS_MACH_WRPPMC_WAR_H
-#define __ASM_MIPS_MACH_WRPPMC_WAR_H
-
-#define R4600_V1_INDEX_ICACHEOP_WAR 0
-#define R4600_V1_HIT_CACHEOP_WAR 0
-#define R4600_V2_HIT_CACHEOP_WAR 0
-#define R5432_CP0_INTERRUPT_WAR 0
-#define BCM1250_M3_WAR 0
-#define SIBYTE_1956_WAR 0
-#define MIPS4K_ICACHE_REFILL_WAR 0
-#define MIPS_CACHE_SYNC_WAR 0
-#define TX49XX_ICACHE_INDEX_INV_WAR 0
-#define ICACHE_REFILLS_WORKAROUND_WAR 1
-#define R10000_LLSC_WAR 0
-#define MIPS34K_MISSED_ITLB_WAR 0
-
-#endif /* __ASM_MIPS_MACH_WRPPMC_WAR_H */
#define ASCII_DISPLAY_WORD_BASE 0x1f000410
#define ASCII_DISPLAY_POS_BASE 0x1f000418
-/*
- * Reset register.
- */
-#define SOFTRES_REG 0x1f000500
-#define GORESET 0x42
-
/*
* Revision register.
*/
#define MIPS_CONF3_RXI (_ULCAST_(1) << 12)
#define MIPS_CONF3_ULRI (_ULCAST_(1) << 13)
#define MIPS_CONF3_ISA (_ULCAST_(3) << 14)
-#define MIPS_CONF3_ISA_OE (_ULCAST_(3) << 16)
+#define MIPS_CONF3_ISA_OE (_ULCAST_(1) << 16)
#define MIPS_CONF3_VZ (_ULCAST_(1) << 23)
#define MIPS_CONF4_MMUSIZEEXT (_ULCAST_(255) << 0)
#define TLBMISS_HANDLER_SETUP_PGD(pgd) \
do { \
- void (*tlbmiss_handler_setup_pgd)(unsigned long); \
- extern u32 tlbmiss_handler_setup_pgd_array[16]; \
- \
- tlbmiss_handler_setup_pgd = \
- (__typeof__(tlbmiss_handler_setup_pgd)) tlbmiss_handler_setup_pgd_array; \
+ extern void tlbmiss_handler_setup_pgd(unsigned long); \
tlbmiss_handler_setup_pgd((unsigned long)(pgd)); \
} while (0)
* Common SMP definitions
*/
#define RESET_VEC_PHYS 0x1fc00000
+#define RESET_VEC_SIZE 8192 /* 8KB reset code and data */
#define RESET_DATA_PHYS (RESET_VEC_PHYS + (1<<10))
+
+/* Offsets of parameters in the RESET_DATA_PHYS area */
#define BOOT_THREAD_MODE 0
#define BOOT_NMI_LOCK 4
#define BOOT_NMI_HANDLER 8
+/* CPU ready flags for each CPU */
+#define BOOT_CPU_READY 2048
+
#ifndef __ASSEMBLY__
#include <linux/cpumask.h>
#include <linux/spinlock.h>
void nlm_rmiboot_preboot(void);
void nlm_percpu_init(int hwcpuid);
+static inline void *
+nlm_get_boot_data(int offset)
+{
+ return (void *)(CKSEG1ADDR(RESET_DATA_PHYS) + offset);
+}
+
static inline void
nlm_set_nmi_handler(void *handler)
{
- char *reset_data;
+ void *nmih = nlm_get_boot_data(BOOT_NMI_HANDLER);
- reset_data = (char *)CKSEG1ADDR(RESET_DATA_PHYS);
- *(int64_t *)(reset_data + BOOT_NMI_HANDLER) = (long)handler;
+ *(int64_t *)nmih = (long)handler;
}
/*
* Misc.
*/
+void nlm_init_boot_cpu(void);
unsigned int nlm_get_cpu_frequency(void);
void nlm_node_init(int node);
extern struct plat_smp_ops nlm_smp_ops;
extern char nlm_reset_entry[], nlm_reset_entry_end[];
+/* SWIOTLB */
+extern struct dma_map_ops nlm_swiotlb_dma_ops;
+
extern unsigned int nlm_threads_per_core;
extern cpumask_t nlm_cpumask;
{
uint64_t ipi;
- ipi = (nmi << 31) | (irq << 20);
+ ipi = ((uint64_t)nmi << 31) | (irq << 20);
ipi |= ((hwt >> 4) << 16) | (1 << (hwt & 0xf)); /* cpuset and mask */
nlm_write_pic_reg(base, PIC_IPI_CTL, ipi);
}
void xlp_mmu_init(void);
void nlm_hal_init(void);
+void *xlp_dt_init(void *fdtp);
#endif /* !__ASSEMBLY__ */
#endif /* _ASM_NLM_XLP_H */
#define nlm_write_c2_cc14(s, v) __write_32bit_c2_register($30, s, v)
#define nlm_write_c2_cc15(s, v) __write_32bit_c2_register($31, s, v)
+#define nlm_read_c2_status0() __read_32bit_c2_register($2, 0)
+#define nlm_write_c2_status0(v) __write_32bit_c2_register($2, 0, v)
+#define nlm_read_c2_status1() __read_32bit_c2_register($2, 1)
+#define nlm_write_c2_status1(v) __write_32bit_c2_register($2, 1, v)
#define nlm_read_c2_status(sel) __read_32bit_c2_register($2, 0)
#define nlm_read_c2_config() __read_32bit_c2_register($3, 0)
#define nlm_write_c2_config(v) __write_32bit_c2_register($3, 0, v)
/*
* Disable interrupts and enable COP2 access
*/
-static inline uint32_t nlm_cop2_enable(void)
+static inline uint32_t nlm_cop2_enable_irqsave(void)
{
uint32_t sr = read_c0_status();
return sr;
}
-static inline void nlm_cop2_restore(uint32_t sr)
+static inline void nlm_cop2_disable_irqrestore(uint32_t sr)
{
write_c0_status(sr);
}
*/
for (i = 0; i < 8; i++) {
nlm_msgsnd(dest);
- status = nlm_read_c2_status(0);
+ status = nlm_read_c2_status0();
if ((status & 0x2) == 1)
pr_info("Send pending fail!\n");
if ((status & 0x4) == 0)
/* wait for load pending to clear */
do {
- status = nlm_read_c2_status(1);
+ status = nlm_read_c2_status0();
} while ((status & 0x08) != 0);
/* receive error bits */
* use any numbers in this range.
*/
CVMX_BOARD_TYPE_CUST_PRIVATE_MIN = 20001,
+ CVMX_BOARD_TYPE_UBNT_E100 = 20002,
CVMX_BOARD_TYPE_CUST_PRIVATE_MAX = 30000,
/* The remaining range is reserved for future use. */
/* Customer private range */
ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MIN)
+ ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E100)
ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MAX)
}
return "Unsupported Board";
#define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_EXEC | \
VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC)
-#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE + \
- PHYS_OFFSET)
-#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET - \
- PHYS_OFFSET)
+#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE)
+#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET)
#include <asm-generic/memory_model.h>
#include <asm-generic/getorder.h>
/*
* Used by boards to register their PCI busses before the actual scanning.
*/
-extern struct pci_controller * alloc_pci_controller(void);
extern void register_pci_controller(struct pci_controller *hose);
/*
struct mips3264_watch_reg_state mips3264;
};
-#ifdef CONFIG_CPU_CAVIUM_OCTEON
+#if defined(CONFIG_CPU_CAVIUM_OCTEON)
struct octeon_cop2_state {
/* DMFC2 rt, 0x0201 */
/* DMFC2 rt, 0x025A; DMFC2 rt, 0x025B - Pass2 */
unsigned long cop2_gfm_result[2];
};
-#define INIT_OCTEON_COP2 {0,}
+#define COP2_INIT \
+ .cp2 = {0,},
struct octeon_cvmseg_state {
unsigned long cvmseg[CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE]
[cpu_dcache_line_size() / sizeof(unsigned long)];
};
+#elif defined(CONFIG_CPU_XLP)
+struct nlm_cop2_state {
+ u64 rx[4];
+ u64 tx[4];
+ u32 tx_msg_status;
+ u32 rx_msg_status;
+};
+
+#define COP2_INIT \
+ .cp2 = {{0}, {0}, 0, 0},
+#else
+#define COP2_INIT
#endif
typedef struct {
unsigned long cp0_baduaddr; /* Last kernel fault accessing USEG */
unsigned long error_code;
#ifdef CONFIG_CPU_CAVIUM_OCTEON
- struct octeon_cop2_state cp2 __attribute__ ((__aligned__(128)));
- struct octeon_cvmseg_state cvmseg __attribute__ ((__aligned__(128)));
+ struct octeon_cop2_state cp2 __attribute__ ((__aligned__(128)));
+ struct octeon_cvmseg_state cvmseg __attribute__ ((__aligned__(128)));
+#endif
+#ifdef CONFIG_CPU_XLP
+ struct nlm_cop2_state cp2;
#endif
struct mips_abi *abi;
};
#define FPAFF_INIT
#endif /* CONFIG_MIPS_MT_FPAFF */
-#ifdef CONFIG_CPU_CAVIUM_OCTEON
-#define OCTEON_INIT \
- .cp2 = INIT_OCTEON_COP2,
-#else
-#define OCTEON_INIT
-#endif /* CONFIG_CPU_CAVIUM_OCTEON */
-
#define INIT_THREAD { \
/* \
* Saved main processor registers \
.cp0_baduaddr = 0, \
.error_code = 0, \
/* \
- * Cavium Octeon specifics (null if not Octeon) \
+ * Platform specific cop2 registers(null if no COP2) \
*/ \
- OCTEON_INIT \
+ COP2_INIT \
}
struct task_struct;
LONG_S $24, PT_R24(sp)
#ifndef CONFIG_CPU_HAS_SMARTMIPS
LONG_S v1, PT_LO(sp)
+#endif
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+ /*
+ * The Octeon multiplier state is affected by general
+ * multiply instructions. It must be saved before and
+ * kernel code might corrupt it
+ */
+ jal octeon_mult_save
#endif
.endm
ori $28, sp, _THREAD_MASK
xori $28, _THREAD_MASK
#ifdef CONFIG_CPU_CAVIUM_OCTEON
- .set mips64
- pref 0, 0($28) /* Prefetch the current pointer */
- pref 0, PT_R31(sp) /* Prefetch the $31(ra) */
- /* The Octeon multiplier state is affected by general multiply
- instructions. It must be saved before and kernel code might
- corrupt it */
- jal octeon_mult_save
- LONG_L v1, 0($28) /* Load the current pointer */
- /* Restore $31(ra) that was changed by the jal */
- LONG_L ra, PT_R31(sp)
- pref 0, 0(v1) /* Prefetch the current thread */
+ .set mips64
+ pref 0, 0($28) /* Prefetch the current pointer */
#endif
.set pop
.endm
.endm
.macro RESTORE_TEMP
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+ /* Restore the Octeon multiplier state */
+ jal octeon_mult_restore
+#endif
#ifdef CONFIG_CPU_HAS_SMARTMIPS
LONG_L $24, PT_ACX(sp)
mtlhx $24
DVPE 5 # dvpe a1
jal mips_ihb
#endif /* CONFIG_MIPS_MT_SMTC */
-#ifdef CONFIG_CPU_CAVIUM_OCTEON
- /* Restore the Octeon multiplier state */
- jal octeon_mult_restore
-#endif
mfc0 a0, CP0_STATUS
ori a0, STATMASK
xori a0, STATMASK
--- /dev/null
+/*
+ * GCC stack protector support.
+ *
+ * (This is directly adopted from the ARM implementation)
+ *
+ * Stack protector works by putting predefined pattern at the start of
+ * the stack frame and verifying that it hasn't been overwritten when
+ * returning from the function. The pattern is called stack canary
+ * and gcc expects it to be defined by a global variable called
+ * "__stack_chk_guard" on MIPS. This unfortunately means that on SMP
+ * we cannot have a different canary value per task.
+ */
+
+#ifndef _ASM_STACKPROTECTOR_H
+#define _ASM_STACKPROTECTOR_H 1
+
+#include <linux/random.h>
+#include <linux/version.h>
+
+extern unsigned long __stack_chk_guard;
+
+/*
+ * Initialize the stackprotector canary value.
+ *
+ * NOTE: this must only be called from functions that never return,
+ * and it must always be inlined.
+ */
+static __always_inline void boot_init_stack_canary(void)
+{
+ unsigned long canary;
+
+ /* Try to get a semi random initial value. */
+ get_random_bytes(&canary, sizeof(canary));
+ canary ^= LINUX_VERSION_CODE;
+
+ current->stack_canary = canary;
+ __stack_chk_guard = current->stack_canary;
+}
+
+#endif /* _ASM_STACKPROTECTOR_H */
#include <asm/cpu-features.h>
#include <asm/watch.h>
#include <asm/dsp.h>
+#include <asm/cop2.h>
struct task_struct;
#define switch_to(prev, next, last) \
do { \
- u32 __usedfpu; \
+ u32 __usedfpu, __c0_stat; \
__mips_mt_fpaff_switch_to(prev); \
if (cpu_has_dsp) \
__save_dsp(prev); \
+ if (cop2_present && (KSTK_STATUS(prev) & ST0_CU2)) { \
+ if (cop2_lazy_restore) \
+ KSTK_STATUS(prev) &= ~ST0_CU2; \
+ __c0_stat = read_c0_status(); \
+ write_c0_status(__c0_stat | ST0_CU2); \
+ cop2_save(&prev->thread.cp2); \
+ write_c0_status(__c0_stat & ~ST0_CU2); \
+ } \
__clear_software_ll_bit(); \
__usedfpu = test_and_clear_tsk_thread_flag(prev, TIF_USEDFPU); \
(last) = resume(prev, next, task_thread_info(next), __usedfpu); \
#define finish_arch_switch(prev) \
do { \
+ u32 __c0_stat; \
+ if (cop2_present && !cop2_lazy_restore && \
+ (KSTK_STATUS(current) & ST0_CU2)) { \
+ __c0_stat = read_c0_status(); \
+ write_c0_status(__c0_stat | ST0_CU2); \
+ cop2_restore(¤t->thread.cp2); \
+ write_c0_status(__c0_stat & ~ST0_CU2); \
+ } \
if (cpu_has_dsp) \
__restore_dsp(current); \
if (cpu_has_userlocal) \
#define TIF_RESTORE_SIGMASK 9 /* restore signal mask in do_signal() */
#define TIF_USEDFPU 16 /* FPU was used by this task this quantum (SMP) */
#define TIF_MEMDIE 18 /* is terminating due to OOM killer */
+#define TIF_NOHZ 19 /* in adaptive nohz mode */
#define TIF_FIXADE 20 /* Fix address errors in software */
#define TIF_LOGADE 21 /* Log address errors to syslog */
#define TIF_32BIT_REGS 22 /* also implies 16/32 fprs */
#define _TIF_SECCOMP (1<<TIF_SECCOMP)
#define _TIF_NOTIFY_RESUME (1<<TIF_NOTIFY_RESUME)
#define _TIF_USEDFPU (1<<TIF_USEDFPU)
+#define _TIF_NOHZ (1<<TIF_NOHZ)
#define _TIF_FIXADE (1<<TIF_FIXADE)
#define _TIF_LOGADE (1<<TIF_LOGADE)
#define _TIF_32BIT_REGS (1<<TIF_32BIT_REGS)
#define _TIF_FPUBOUND (1<<TIF_FPUBOUND)
#define _TIF_LOAD_WATCH (1<<TIF_LOAD_WATCH)
+#define _TIF_WORK_SYSCALL_ENTRY (_TIF_NOHZ | _TIF_SYSCALL_TRACE | \
+ _TIF_SYSCALL_AUDIT)
+
/* work to do in syscall_trace_leave() */
-#define _TIF_WORK_SYSCALL_EXIT (_TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT)
+#define _TIF_WORK_SYSCALL_EXIT (_TIF_NOHZ | _TIF_SYSCALL_TRACE | \
+ _TIF_SYSCALL_AUDIT)
/* work to do on interrupt/exception return */
#define _TIF_WORK_MASK \
(_TIF_SIGPENDING | _TIF_NEED_RESCHED | _TIF_NOTIFY_RESUME)
/* work to do on any return to u-space */
-#define _TIF_ALLWORK_MASK (_TIF_WORK_MASK | _TIF_WORK_SYSCALL_EXIT)
+#define _TIF_ALLWORK_MASK (_TIF_NOHZ | _TIF_WORK_MASK | \
+ _TIF_WORK_SYSCALL_EXIT)
#endif /* __KERNEL__ */
#define XIO_PORT(x) ((xwidgetnum_t)(((x)&XIO_PORT_BITS) >> XIO_PORT_SHIFT))
#define XIO_PACK(p, o) ((((uint64_t)(p))<<XIO_PORT_SHIFT) | ((o)&XIO_ADDR_BITS))
+#ifdef CONFIG_PCI
+extern int bridge_probe(nasid_t nasid, int widget, int masterwid);
+#else
+static inline int bridge_probe(nasid_t nasid, int widget, int masterwid)
+{
+ return 0;
+}
+#endif
+
#endif /* !__ASSEMBLY__ */
#endif /* _ASM_XTALK_XTALK_H */
*
* Copyright (C) 1995, 96, 97, 98, 99, 2003, 05 Ralf Baechle
*/
-#ifndef _ASM_FCNTL_H
-#define _ASM_FCNTL_H
+#ifndef _UAPI_ASM_FCNTL_H
+#define _UAPI_ASM_FCNTL_H
+#include <asm/sgidefs.h>
#define O_APPEND 0x0008
#define O_DSYNC 0x0010 /* used to be O_SYNC, see below */
* contain all the same fields as struct flock.
*/
-#ifdef CONFIG_32BIT
+#if _MIPS_SIM != _MIPS_SIM_ABI64
+
#include <linux/types.h>
struct flock {
short l_type;
short l_whence;
- off_t l_start;
- off_t l_len;
+ __kernel_off_t l_start;
+ __kernel_off_t l_len;
long l_sysid;
__kernel_pid_t l_pid;
long pad[4];
#define HAVE_ARCH_STRUCT_FLOCK
-#endif /* CONFIG_32BIT */
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
#include <asm-generic/fcntl.h>
-#endif /* _ASM_FCNTL_H */
+#endif /* _UAPI_ASM_FCNTL_H */
enum mm_16c_minor_op {
mm_lwm16_op = 0x04,
mm_swm16_op = 0x05,
- mm_jr16_op = 0x18,
- mm_jrc_op = 0x1a,
- mm_jalr16_op = 0x1c,
- mm_jalrs16_op = 0x1e,
+ mm_jr16_op = 0x0c,
+ mm_jrc_op = 0x0d,
+ mm_jalr16_op = 0x0e,
+ mm_jalrs16_op = 0x0f,
+ mm_jraddiusp_op = 0x18,
};
/*
struct msqid64_ds {
struct ipc64_perm msg_perm;
-#if defined(CONFIG_32BIT) && !defined(CONFIG_CPU_LITTLE_ENDIAN)
+#if !defined(__mips64) && defined(__MIPSEB__)
unsigned long __unused1;
#endif
__kernel_time_t msg_stime; /* last msgsnd time */
-#if defined(CONFIG_32BIT) && defined(CONFIG_CPU_LITTLE_ENDIAN)
+#if !defined(__mips64) && defined(__MIPSEL__)
unsigned long __unused1;
#endif
-#if defined(CONFIG_32BIT) && !defined(CONFIG_CPU_LITTLE_ENDIAN)
+#if !defined(__mips64) && defined(__MIPSEB__)
unsigned long __unused2;
#endif
__kernel_time_t msg_rtime; /* last msgrcv time */
-#if defined(CONFIG_32BIT) && defined(CONFIG_CPU_LITTLE_ENDIAN)
+#if !defined(__mips64) && defined(__MIPSEL__)
unsigned long __unused2;
#endif
-#if defined(CONFIG_32BIT) && !defined(CONFIG_CPU_LITTLE_ENDIAN)
+#if !defined(__mips64) && defined(__MIPSEB__)
unsigned long __unused3;
#endif
__kernel_time_t msg_ctime; /* last change time */
-#if defined(CONFIG_32BIT) && defined(CONFIG_CPU_LITTLE_ENDIAN)
+#if !defined(__mips64) && defined(__MIPSEL__)
unsigned long __unused3;
#endif
unsigned long msg_cbytes; /* current number of bytes on queue */
* but we keep the old value on MIPS32,
* for compatibility:
*/
-#ifdef CONFIG_32BIT
+#ifndef __mips64
# define RLIM_INFINITY 0x7fffffffUL
#endif
/*
* Careful to keep union _sifields from shifting ...
*/
-#ifdef CONFIG_32BIT
+#if __SIZEOF_LONG__ == 4
#define __ARCH_SI_PREAMBLE_SIZE (3 * sizeof(int))
#endif
-#ifdef CONFIG_64BIT
+#if __SIZEOF_LONG__ == 8
#define __ARCH_SI_PREAMBLE_SIZE (4 * sizeof(int))
#endif
#define __SWAB_64_THRU_32__
-#ifdef CONFIG_CPU_MIPSR2
+#if defined(__mips_isa_rev) && (__mips_isa_rev >= 2)
static inline __attribute_const__ __u16 __arch_swab16(__u16 x)
{
#define __arch_swab32 __arch_swab32
/*
- * Having already checked for CONFIG_CPU_MIPSR2, enable the
- * optimized version for 64-bit kernel on r2 CPUs.
+ * Having already checked for MIPS R2, enable the optimized version for
+ * 64-bit kernel on r2 CPUs.
*/
-#ifdef CONFIG_64BIT
+#ifdef __mips64
static inline __attribute_const__ __u64 __arch_swab64(__u64 x)
{
__asm__(
return x;
}
#define __arch_swab64 __arch_swab64
-#endif /* CONFIG_64BIT */
-#endif /* CONFIG_CPU_MIPSR2 */
+#endif /* __mips64 */
+#endif /* MIPS R2 or newer */
#endif /* _ASM_SWAB_H */
OFFSET(TASK_FLAGS, task_struct, flags);
OFFSET(TASK_MM, task_struct, mm);
OFFSET(TASK_PID, task_struct, pid);
+#if defined(CONFIG_CC_STACKPROTECTOR)
+ OFFSET(TASK_STACK_CANARY, task_struct, stack_canary);
+#endif
DEFINE(TASK_STRUCT_SIZE, sizeof(struct task_struct));
BLANK();
}
printk("%s: unaligned epc - sending SIGBUS.\n", current->comm);
force_sig(SIGBUS, current);
return -EFAULT;
-
}
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
+#include <linux/context_tracking.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/ptrace.h>
asmlinkage void __init do_daddi_ov(struct pt_regs *regs)
{
+ enum ctx_state prev_state;
+
+ prev_state = exception_enter();
daddi_ov = 1;
regs->cp0_epc += 4;
+ exception_exit(prev_state);
}
static inline void check_daddi(void)
case MIPS_CPU_ISA_IV:
c->isa_level |= MIPS_CPU_ISA_IV;
case MIPS_CPU_ISA_III:
- c->isa_level |= MIPS_CPU_ISA_I | MIPS_CPU_ISA_II |
- MIPS_CPU_ISA_III;
+ c->isa_level |= MIPS_CPU_ISA_II | MIPS_CPU_ISA_III;
break;
case MIPS_CPU_ISA_M32R2:
c->isa_level |= MIPS_CPU_ISA_M32R1;
case MIPS_CPU_ISA_II:
c->isa_level |= MIPS_CPU_ISA_II;
- case MIPS_CPU_ISA_I:
- c->isa_level |= MIPS_CPU_ISA_I;
break;
}
}
c->options |= MIPS_CPU_ULRI;
if (config3 & MIPS_CONF3_ISA)
c->options |= MIPS_CPU_MICROMIPS;
-#ifdef CONFIG_CPU_MICROMIPS
- write_c0_config3(read_c0_config3() | MIPS_CONF3_ISA_OE);
-#endif
if (config3 & MIPS_CONF3_VZ)
c->ases |= MIPS_ASE_VZ;
case PRID_IMP_R2000:
c->cputype = CPU_R2000;
__cpu_name[cpu] = "R2000";
- set_isa(c, MIPS_CPU_ISA_I);
c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
MIPS_CPU_NOFPUEX;
if (__cpu_has_fpu())
c->cputype = CPU_R3000;
__cpu_name[cpu] = "R3000";
}
- set_isa(c, MIPS_CPU_ISA_I);
c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
MIPS_CPU_NOFPUEX;
if (__cpu_has_fpu())
break;
#endif
case PRID_IMP_TX39:
- set_isa(c, MIPS_CPU_ISA_I);
c->options = MIPS_CPU_TLB | MIPS_CPU_TX39_CACHE;
if ((c->processor_id & 0xf0) == (PRID_REV_TX3927 & 0xf0)) {
set_isa(c, MIPS_CPU_ISA_M64R1);
c->tlbsize = ((read_c0_config1() >> 25) & 0x3f) + 1;
}
+ c->kscratch_mask = 0xf;
}
#ifdef CONFIG_64BIT
#include <kernel-entry-init.h>
- /*
- * inputs are the text nasid in t1, data nasid in t2.
- */
- .macro MAPPED_KERNEL_SETUP_TLB
-#ifdef CONFIG_MAPPED_KERNEL
- /*
- * This needs to read the nasid - assume 0 for now.
- * Drop in 0xffffffffc0000000 in tlbhi, 0+VG in tlblo_0,
- * 0+DVG in tlblo_1.
- */
- dli t0, 0xffffffffc0000000
- dmtc0 t0, CP0_ENTRYHI
- li t0, 0x1c000 # Offset of text into node memory
- dsll t1, NASID_SHFT # Shift text nasid into place
- dsll t2, NASID_SHFT # Same for data nasid
- or t1, t1, t0 # Physical load address of kernel text
- or t2, t2, t0 # Physical load address of kernel data
- dsrl t1, 12 # 4K pfn
- dsrl t2, 12 # 4K pfn
- dsll t1, 6 # Get pfn into place
- dsll t2, 6 # Get pfn into place
- li t0, ((_PAGE_GLOBAL|_PAGE_VALID| _CACHE_CACHABLE_COW) >> 6)
- or t0, t0, t1
- mtc0 t0, CP0_ENTRYLO0 # physaddr, VG, cach exlwr
- li t0, ((_PAGE_GLOBAL|_PAGE_VALID| _PAGE_DIRTY|_CACHE_CACHABLE_COW) >> 6)
- or t0, t0, t2
- mtc0 t0, CP0_ENTRYLO1 # physaddr, DVG, cach exlwr
- li t0, 0x1ffe000 # MAPPED_KERN_TLBMASK, TLBPGMASK_16M
- mtc0 t0, CP0_PAGEMASK
- li t0, 0 # KMAP_INX
- mtc0 t0, CP0_INDEX
- li t0, 1
- mtc0 t0, CP0_WIRED
- tlbwi
-#else
- mtc0 zero, CP0_WIRED
-#endif
- .endm
-
/*
* For the moment disable interrupts, mark the kernel mode and
* set ST0_KX so that the CPU does not spit fire when using
/* Assumption : cpumask refers to a single CPU */
spin_lock_irqsave(&gic_lock, flags);
- for (;;) {
- /* Re-route this IRQ */
- GIC_SH_MAP_TO_VPE_SMASK(irq, first_cpu(tmp));
- /* Update the pcpu_masks */
- for (i = 0; i < NR_CPUS; i++)
- clear_bit(irq, pcpu_masks[i].pcpu_mask);
- set_bit(irq, pcpu_masks[first_cpu(tmp)].pcpu_mask);
+ /* Re-route this IRQ */
+ GIC_SH_MAP_TO_VPE_SMASK(irq, first_cpu(tmp));
+
+ /* Update the pcpu_masks */
+ for (i = 0; i < NR_CPUS; i++)
+ clear_bit(irq, pcpu_masks[i].pcpu_mask);
+ set_bit(irq, pcpu_masks[first_cpu(tmp)].pcpu_mask);
- }
cpumask_copy(d->affinity, cpumask);
spin_unlock_irqrestore(&gic_lock, flags);
#endif
/* arg3: Get frame pointer of current stack */
-#ifdef CONFIG_FRAME_POINTER
- move a2, fp
-#else /* ! CONFIG_FRAME_POINTER */
#ifdef CONFIG_64BIT
PTR_LA a2, PT_SIZE(sp)
#else
PTR_LA a2, (PT_SIZE+8)(sp)
-#endif
#endif
jal prepare_ftrace_return
cpu_save_nonscratch a0
LONG_S ra, THREAD_REG31(a0)
- /* check if we need to save COP2 registers */
- PTR_L t2, TASK_THREAD_INFO(a0)
- LONG_L t0, ST_OFF(t2)
- bbit0 t0, 30, 1f
-
- /* Disable COP2 in the stored process state */
- li t1, ST0_CU2
- xor t0, t1
- LONG_S t0, ST_OFF(t2)
-
- /* Enable COP2 so we can save it */
- mfc0 t0, CP0_STATUS
- or t0, t1
- mtc0 t0, CP0_STATUS
-
- /* Save COP2 */
- daddu a0, THREAD_CP2
- jal octeon_cop2_save
- dsubu a0, THREAD_CP2
-
- /* Disable COP2 now that we are done */
- mfc0 t0, CP0_STATUS
- li t1, ST0_CU2
- xor t0, t1
- mtc0 t0, CP0_STATUS
-
-1:
#if CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE > 0
/* Check if we need to store CVMSEG state */
mfc0 t0, $11,7 /* CvmMemCtl */
mtc0 t0, $11,7 /* CvmMemCtl */
#endif
3:
+
+#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
+ PTR_L t8, __stack_chk_guard
+ LONG_L t9, TASK_STACK_CANARY(a1)
+ LONG_S t9, 0(t8)
+#endif
+
/*
* The order of restoring the registers takes care of the race
* updating $28, $29 and kernelsp without disabling ints.
seq_printf(m, "]\n");
}
if (cpu_has_mips_r) {
- seq_printf(m, "isa\t\t\t:");
- if (cpu_has_mips_1)
- seq_printf(m, "%s", " mips1");
+ seq_printf(m, "isa\t\t\t: mips1");
if (cpu_has_mips_2)
seq_printf(m, "%s", " mips2");
if (cpu_has_mips_3)
return 1;
}
-/*
- *
- */
+#ifdef CONFIG_CC_STACKPROTECTOR
+#include <linux/stackprotector.h>
+unsigned long __stack_chk_guard __read_mostly;
+EXPORT_SYMBOL(__stack_chk_guard);
+#endif
+
struct mips_frame_info {
void *func;
unsigned long func_size;
if (name == NULL)
return;
- strncpy(mips_machine_name, name, sizeof(mips_machine_name));
+ strlcpy(mips_machine_name, name, sizeof(mips_machine_name));
pr_info("MIPS: machine is %s\n", mips_get_machine_name());
}
* binaries.
*/
#include <linux/compiler.h>
+#include <linux/context_tracking.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/mm.h>
*/
asmlinkage void syscall_trace_enter(struct pt_regs *regs)
{
+ user_exit();
+
/* do the secure computing check first */
secure_computing_strict(regs->regs[2]);
*/
asmlinkage void syscall_trace_leave(struct pt_regs *regs)
{
+ /*
+ * We may come here right after calling schedule_user()
+ * or do_notify_resume(), in which case we can be in RCU
+ * user mode.
+ */
+ user_exit();
+
audit_syscall_exit(regs);
if (!(current->ptrace & PT_PTRACED))
send_sig(current->exit_code, current, 1);
current->exit_code = 0;
}
+
+ user_enter();
}
fpu_save_single a0, t0 # clobbers t0
1:
+
+#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
+ PTR_L t8, __stack_chk_guard
+ LONG_L t9, TASK_STACK_CANARY(a1)
+ LONG_S t9, 0(t8)
+#endif
+
/*
* The order of restoring the registers takes care of the race
* updating $28, $29 and kernelsp without disabling ints.
# clobbers t1
1:
+#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
+ PTR_L t8, __stack_chk_guard
+ LONG_L t9, TASK_STACK_CANARY(a1)
+ LONG_S t9, 0(t8)
+#endif
+
/*
* The order of restoring the registers takes care of the race
* updating $28, $29 and kernelsp without disabling ints.
size_t count, loff_t * ppos)
{
int minor = iminor(file_inode(file));
- struct rtlx_channel *rt = &rtlx->channel[minor];
/* any space left... */
if (!rtlx_write_poll(minor)) {
stack_done:
lw t0, TI_FLAGS($28) # syscall tracing enabled?
- li t1, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT
+ li t1, _TIF_WORK_SYSCALL_ENTRY
and t0, t1
bnez t0, syscall_trace_entry # -> yes
sd a3, PT_R26(sp) # save a3 for syscall restarting
- li t1, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT
+ li t1, _TIF_WORK_SYSCALL_ENTRY
LONG_L t0, TI_FLAGS($28) # syscall tracing enabled?
and t0, t1, t0
bnez t0, syscall_trace_entry
sd a3, PT_R26(sp) # save a3 for syscall restarting
- li t1, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT
+ li t1, _TIF_WORK_SYSCALL_ENTRY
LONG_L t0, TI_FLAGS($28) # syscall tracing enabled?
and t0, t1, t0
bnez t0, n32_syscall_trace_entry
PTR 4b, bad_stack
.previous
- li t1, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT
+ li t1, _TIF_WORK_SYSCALL_ENTRY
LONG_L t0, TI_FLAGS($28) # syscall tracing enabled?
and t0, t1, t0
bnez t0, trace_a_syscall
* Copyright (C) 1999, 2000 Silicon Graphics, Inc.
*/
#include <linux/cache.h>
+#include <linux/context_tracking.h>
#include <linux/irqflags.h>
#include <linux/sched.h>
#include <linux/mm.h>
{
local_irq_enable();
+ user_exit();
+
/* deal with pending signal delivery */
if (thread_info_flags & _TIF_SIGPENDING)
do_signal(regs);
clear_thread_flag(TIF_NOTIFY_RESUME);
tracehook_notify_resume(regs);
}
+
+ user_enter();
}
#ifdef CONFIG_SMP
static void __init bmips_smp_setup(void)
{
- int i;
+ int i, cpu = 1, boot_cpu = 0;
#if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380)
/* arbitration priority */
/* NBK and weak order flags */
set_c0_brcm_config_0(0x30000);
+ /* Find out if we are running on TP0 or TP1 */
+ boot_cpu = !!(read_c0_brcm_cmt_local() & (1 << 31));
+
/*
* MIPS interrupts 0,1 (SW INT 0,1) cross over to the other thread
* MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output
* MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output
+ *
+ * If booting from TP1, leave the existing CMT interrupt routing
+ * such that TP0 responds to SW1 and TP1 responds to SW0.
*/
- change_c0_brcm_cmt_intr(0xf8018000,
- (0x02 << 27) | (0x03 << 15));
+ if (boot_cpu == 0)
+ change_c0_brcm_cmt_intr(0xf8018000,
+ (0x02 << 27) | (0x03 << 15));
+ else
+ change_c0_brcm_cmt_intr(0xf8018000, (0x1d << 27));
/* single core, 2 threads (2 pipelines) */
max_cpus = 2;
if (!board_ebase_setup)
board_ebase_setup = &bmips_ebase_setup;
+ __cpu_number_map[boot_cpu] = 0;
+ __cpu_logical_map[0] = boot_cpu;
+
for (i = 0; i < max_cpus; i++) {
- __cpu_number_map[i] = 1;
- __cpu_logical_map[i] = 1;
+ if (i != boot_cpu) {
+ __cpu_number_map[i] = cpu;
+ __cpu_logical_map[cpu] = i;
+ cpu++;
+ }
set_cpu_possible(i, 1);
set_cpu_present(i, 1);
}
bmips_send_ipi_single(cpu, 0);
else {
#if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380)
- set_c0_brcm_cmt_ctrl(0x01);
+ /* Reset slave TP1 if booting from TP0 */
+ if (cpu_logical_map(cpu) == 0)
+ set_c0_brcm_cmt_ctrl(0x01);
#elif defined(CONFIG_CPU_BMIPS5000)
if (cpu & 0x01)
write_c0_brcm_action(ACTION_BOOT_THREAD(cpu));
*/
#include <linux/bug.h>
#include <linux/compiler.h>
+#include <linux/context_tracking.h>
#include <linux/kexec.h>
#include <linux/init.h>
#include <linux/kernel.h>
printk("Status: %08x ", (uint32_t) regs->cp0_status);
- if (current_cpu_data.isa_level == MIPS_CPU_ISA_I) {
+ if (cpu_has_3kex) {
if (regs->cp0_status & ST0_KUO)
printk("KUo ");
if (regs->cp0_status & ST0_IEO)
printk("KUc ");
if (regs->cp0_status & ST0_IEC)
printk("IEc ");
- } else {
+ } else if (cpu_has_4kex) {
if (regs->cp0_status & ST0_KX)
printk("KX ");
if (regs->cp0_status & ST0_SX)
const struct exception_table_entry *fixup = NULL;
int data = regs->cp0_cause & 4;
int action = MIPS_BE_FATAL;
+ enum ctx_state prev_state;
+ prev_state = exception_enter();
/* XXX For now. Fixme, this searches the wrong table ... */
if (data && !user_mode(regs))
fixup = search_dbe_tables(exception_epc(regs));
switch (action) {
case MIPS_BE_DISCARD:
- return;
+ goto out;
case MIPS_BE_FIXUP:
if (fixup) {
regs->cp0_epc = fixup->nextinsn;
- return;
+ goto out;
}
break;
default:
field, regs->cp0_epc, field, regs->regs[31]);
if (notify_die(DIE_OOPS, "bus error", regs, 0, regs_to_trapnr(regs), SIGBUS)
== NOTIFY_STOP)
- return;
+ goto out;
die_if_kernel("Oops", regs);
force_sig(SIGBUS, current);
+
+out:
+ exception_exit(prev_state);
}
/*
asmlinkage void do_ov(struct pt_regs *regs)
{
+ enum ctx_state prev_state;
siginfo_t info;
+ prev_state = exception_enter();
die_if_kernel("Integer overflow", regs);
info.si_code = FPE_INTOVF;
info.si_errno = 0;
info.si_addr = (void __user *) regs->cp0_epc;
force_sig_info(SIGFPE, &info, current);
+ exception_exit(prev_state);
}
int process_fpemu_return(int sig, void __user *fault_addr)
*/
asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31)
{
+ enum ctx_state prev_state;
siginfo_t info = {0};
+ prev_state = exception_enter();
if (notify_die(DIE_FP, "FP exception", regs, 0, regs_to_trapnr(regs), SIGFPE)
== NOTIFY_STOP)
- return;
+ goto out;
die_if_kernel("FP exception in kernel code", regs);
if (fcr31 & FPU_CSR_UNI_X) {
/* If something went wrong, signal */
process_fpemu_return(sig, fault_addr);
- return;
+ goto out;
} else if (fcr31 & FPU_CSR_INV_X)
info.si_code = FPE_FLTINV;
else if (fcr31 & FPU_CSR_DIV_X)
info.si_errno = 0;
info.si_addr = (void __user *) regs->cp0_epc;
force_sig_info(SIGFPE, &info, current);
+
+out:
+ exception_exit(prev_state);
}
static void do_trap_or_bp(struct pt_regs *regs, unsigned int code,
asmlinkage void do_bp(struct pt_regs *regs)
{
unsigned int opcode, bcode;
+ enum ctx_state prev_state;
unsigned long epc;
u16 instr[2];
+ prev_state = exception_enter();
if (get_isa16_mode(regs->cp0_epc)) {
/* Calculate EPC. */
epc = exception_epc(regs);
goto out_sigsegv;
bcode = (instr[0] >> 6) & 0x3f;
do_trap_or_bp(regs, bcode, "Break");
- return;
+ goto out;
}
} else {
if (__get_user(opcode, (unsigned int __user *) exception_epc(regs)))
switch (bcode) {
case BRK_KPROBE_BP:
if (notify_die(DIE_BREAK, "debug", regs, bcode, regs_to_trapnr(regs), SIGTRAP) == NOTIFY_STOP)
- return;
+ goto out;
else
break;
case BRK_KPROBE_SSTEPBP:
if (notify_die(DIE_SSTEPBP, "single_step", regs, bcode, regs_to_trapnr(regs), SIGTRAP) == NOTIFY_STOP)
- return;
+ goto out;
else
break;
default:
}
do_trap_or_bp(regs, bcode, "Break");
+
+out:
+ exception_exit(prev_state);
return;
out_sigsegv:
force_sig(SIGSEGV, current);
+ goto out;
}
asmlinkage void do_tr(struct pt_regs *regs)
{
u32 opcode, tcode = 0;
+ enum ctx_state prev_state;
u16 instr[2];
unsigned long epc = msk_isa16_mode(exception_epc(regs));
+ prev_state = exception_enter();
if (get_isa16_mode(regs->cp0_epc)) {
if (__get_user(instr[0], (u16 __user *)(epc + 0)) ||
__get_user(instr[1], (u16 __user *)(epc + 2)))
}
do_trap_or_bp(regs, tcode, "Trap");
+
+out:
+ exception_exit(prev_state);
return;
out_sigsegv:
force_sig(SIGSEGV, current);
+ goto out;
}
asmlinkage void do_ri(struct pt_regs *regs)
unsigned int __user *epc = (unsigned int __user *)exception_epc(regs);
unsigned long old_epc = regs->cp0_epc;
unsigned long old31 = regs->regs[31];
+ enum ctx_state prev_state;
unsigned int opcode = 0;
int status = -1;
+ prev_state = exception_enter();
if (notify_die(DIE_RI, "RI Fault", regs, 0, regs_to_trapnr(regs), SIGILL)
== NOTIFY_STOP)
- return;
+ goto out;
die_if_kernel("Reserved instruction in kernel code", regs);
if (unlikely(compute_return_epc(regs) < 0))
- return;
+ goto out;
if (get_isa16_mode(regs->cp0_epc)) {
unsigned short mmop[2] = { 0 };
regs->regs[31] = old31;
force_sig(status, current);
}
+
+out:
+ exception_exit(prev_state);
}
/*
{
struct pt_regs *regs = data;
- switch (action) {
- default:
- die_if_kernel("Unhandled kernel unaligned access or invalid "
+ die_if_kernel("COP2: Unhandled kernel unaligned access or invalid "
"instruction", regs);
- /* Fall through */
-
- case CU2_EXCEPTION:
- force_sig(SIGILL, current);
- }
+ force_sig(SIGILL, current);
return NOTIFY_OK;
}
asmlinkage void do_cpu(struct pt_regs *regs)
{
+ enum ctx_state prev_state;
unsigned int __user *epc;
unsigned long old_epc, old31;
unsigned int opcode;
int status;
unsigned long __maybe_unused flags;
- die_if_kernel("do_cpu invoked from kernel context!", regs);
-
+ prev_state = exception_enter();
cpid = (regs->cp0_cause >> CAUSEB_CE) & 3;
+ if (cpid != 2)
+ die_if_kernel("do_cpu invoked from kernel context!", regs);
+
switch (cpid) {
case 0:
epc = (unsigned int __user *)exception_epc(regs);
status = -1;
if (unlikely(compute_return_epc(regs) < 0))
- return;
+ goto out;
if (get_isa16_mode(regs->cp0_epc)) {
unsigned short mmop[2] = { 0 };
force_sig(status, current);
}
- return;
+ goto out;
case 3:
/*
mt_ase_fp_affinity();
}
- return;
+ goto out;
case 2:
raw_notifier_call_chain(&cu2_chain, CU2_EXCEPTION, regs);
- return;
+ goto out;
}
force_sig(SIGILL, current);
+
+out:
+ exception_exit(prev_state);
}
asmlinkage void do_mdmx(struct pt_regs *regs)
{
+ enum ctx_state prev_state;
+
+ prev_state = exception_enter();
force_sig(SIGILL, current);
+ exception_exit(prev_state);
}
/*
*/
asmlinkage void do_watch(struct pt_regs *regs)
{
+ enum ctx_state prev_state;
u32 cause;
+ prev_state = exception_enter();
/*
* Clear WP (bit 22) bit of cause register so we don't loop
* forever.
mips_clear_watch_registers();
local_irq_enable();
}
+ exception_exit(prev_state);
}
asmlinkage void do_mcheck(struct pt_regs *regs)
{
const int field = 2 * sizeof(unsigned long);
int multi_match = regs->cp0_status & ST0_TS;
+ enum ctx_state prev_state;
+ prev_state = exception_enter();
show_regs(regs);
if (multi_match) {
panic("Caught Machine Check exception - %scaused by multiple "
"matching entries in the TLB.",
(multi_match) ? "" : "not ");
+ exception_exit(prev_state);
}
asmlinkage void do_mt(struct pt_regs *regs)
}
extern void tlb_init(void);
-extern void flush_tlb_handlers(void);
/*
* Timer interrupt
ebase += (read_c0_ebase() & 0x3ffff000);
}
+ if (cpu_has_mmips) {
+ unsigned int config3 = read_c0_config3();
+
+ if (IS_ENABLED(CONFIG_CPU_MICROMIPS))
+ write_c0_config3(config3 | MIPS_CONF3_ISA_OE);
+ else
+ write_c0_config3(config3 & ~MIPS_CONF3_ISA_OE);
+ }
+
if (board_ebase_setup)
board_ebase_setup();
per_cpu_trap_init(true);
set_handler(0x080, &except_vec3_generic, 0x80);
local_flush_icache_range(ebase, ebase + 0x400);
- flush_tlb_handlers();
sort_extable(__start___dbe_table, __stop___dbe_table);
* A store crossing a page boundary might be executed only partially.
* Undo the partial store in this case.
*/
+#include <linux/context_tracking.h>
#include <linux/mm.h>
#include <linux/signal.h>
#include <linux/smp.h>
/* Recode table from 16-bit STORE register notation to 32-bit GPR. */
const int reg16to32st[] = { 0, 17, 2, 3, 4, 5, 6, 7 };
-void emulate_load_store_microMIPS(struct pt_regs *regs, void __user * addr)
+static void emulate_load_store_microMIPS(struct pt_regs *regs,
+ void __user *addr)
{
unsigned long value;
unsigned int res;
("Unhandled kernel unaligned access or invalid instruction", regs);
force_sig(SIGILL, current);
}
+
asmlinkage void do_ade(struct pt_regs *regs)
{
+ enum ctx_state prev_state;
unsigned int __user *pc;
mm_segment_t seg;
+ prev_state = exception_enter();
perf_sw_event(PERF_COUNT_SW_ALIGNMENT_FAULTS,
1, regs, regs->cp0_badvaddr);
/*
/*
* XXX On return from the signal handler we should advance the epc
*/
+ exception_exit(prev_state);
}
#ifdef CONFIG_DEBUG_FS
* disable the register.
*/
write_c0_watchlo0(7);
+ back_to_back_c0_hazard();
t = read_c0_watchlo0();
write_c0_watchlo0(0);
c->watch_reg_masks[0] = t & 7;
c->watch_reg_use_cnt = 1;
t = read_c0_watchhi0();
write_c0_watchhi0(t | 0xff8);
+ back_to_back_c0_hazard();
t = read_c0_watchhi0();
c->watch_reg_masks[0] |= (t & 0xff8);
if ((t & 0x80000000) == 0)
return;
write_c0_watchlo1(7);
+ back_to_back_c0_hazard();
t = read_c0_watchlo1();
write_c0_watchlo1(0);
c->watch_reg_masks[1] = t & 7;
c->watch_reg_use_cnt = 2;
t = read_c0_watchhi1();
write_c0_watchhi1(t | 0xff8);
+ back_to_back_c0_hazard();
t = read_c0_watchhi1();
c->watch_reg_masks[1] |= (t & 0xff8);
if ((t & 0x80000000) == 0)
return;
write_c0_watchlo2(7);
+ back_to_back_c0_hazard();
t = read_c0_watchlo2();
write_c0_watchlo2(0);
c->watch_reg_masks[2] = t & 7;
c->watch_reg_use_cnt = 3;
t = read_c0_watchhi2();
write_c0_watchhi2(t | 0xff8);
+ back_to_back_c0_hazard();
t = read_c0_watchhi2();
c->watch_reg_masks[2] |= (t & 0xff8);
if ((t & 0x80000000) == 0)
return;
write_c0_watchlo3(7);
+ back_to_back_c0_hazard();
t = read_c0_watchlo3();
write_c0_watchlo3(0);
c->watch_reg_masks[3] = t & 7;
c->watch_reg_use_cnt = 4;
t = read_c0_watchhi3();
write_c0_watchhi3(t | 0xff8);
+ back_to_back_c0_hazard();
t = read_c0_watchhi3();
c->watch_reg_masks[3] |= (t & 0xff8);
if ((t & 0x80000000) == 0)
if (!of_have_populated_dt())
panic("device tree not present");
- strncpy(of_ids[0].compatible, soc_info.compatible,
+ strlcpy(of_ids[0].compatible, soc_info.compatible,
sizeof(of_ids[0].compatible));
strncpy(of_ids[1].compatible, "simple-bus",
sizeof(of_ids[1].compatible));
/* And the same for proc */
-int proc_dolasatstring(ctl_table *table, int write,
+int proc_dolasatstring(struct ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
int r;
}
/* proc function to write EEPROM after changing int entry */
-int proc_dolasatint(ctl_table *table, int write,
+int proc_dolasatint(struct ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
int r;
static int rtctmp;
/* proc function to read/write RealTime Clock */
-int proc_dolasatrtc(ctl_table *table, int write,
+int proc_dolasatrtc(struct ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
struct timespec ts;
#endif
#ifdef CONFIG_INET
-int proc_lasat_ip(ctl_table *table, int write,
+int proc_lasat_ip(struct ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
unsigned int ip;
}
#endif
-int proc_lasat_prid(ctl_table *table, int write,
+int proc_lasat_prid(struct ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
int r;
extern int lasat_boot_to_service;
-static ctl_table lasat_table[] = {
+static struct ctl_table lasat_table[] = {
{
.procname = "cpu-hz",
.data = &lasat_board_info.li_cpu_hz,
{}
};
-static ctl_table lasat_root_table[] = {
+static struct ctl_table lasat_root_table[] = {
{
.procname = "lasat",
.mode = 0555,
* option) any later version.
*/
+#include <linux/pci.h>
#include <cs5536/cs5536.h>
#include <cs5536/cs5536_pci.h>
return conf_data;
}
+
+/*
+ * The mfgpt timer interrupt is running early, so we must keep the south bridge
+ * mmio always enabled. Otherwise we may race with the PCI configuration which
+ * may temporarily disable it. When that happens and the timer interrupt fires,
+ * we are not able to clear it and the system will hang.
+ */
+static void cs5536_isa_mmio_always_on(struct pci_dev *dev)
+{
+ dev->mmio_always_on = 1;
+}
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA,
+ PCI_CLASS_BRIDGE_ISA, 8, cs5536_isa_mmio_always_on);
unsigned int fcr31;
unsigned int bit;
+ if (!cpu_has_mmips)
+ return 0;
+
switch (insn.mm_i_format.opcode) {
case mm_pool32a_op:
if ((insn.mm_i_format.simmediate & MM_POOL32A_MINOR_MASK) ==
obj-y += cache.o dma-default.o extable.o fault.o \
gup.o init.o mmap.o page.o page-funcs.o \
- tlbex.o tlbex-fault.o uasm-mips.o
+ tlbex.o tlbex-fault.o tlb-funcs.o uasm-mips.o
obj-$(CONFIG_32BIT) += ioremap.o pgtable-32.o
obj-$(CONFIG_64BIT) += pgtable-64.o
#ifdef CONFIG_SIBYTE_BW_TRACE
/* Freeze the trace buffer now */
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
- csr_out32(M_BCM1480_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG));
-#else
csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG));
-#endif
printk("Trace buffer frozen\n");
#endif
if (!plat_device_is_coherent(dev))
__dma_sync(sg_page(sg), sg->offset, sg->length,
direction);
+#ifdef CONFIG_NEED_SG_DMA_LENGTH
+ sg->dma_length = sg->length;
+#endif
sg->dma_address = plat_map_dma_mem_page(dev, sg_page(sg)) +
sg->offset;
}
*
* Copyright (C) 1995 - 2000 by Ralf Baechle
*/
+#include <linux/context_tracking.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
* and the problem, and then passes it off to one of the appropriate
* routines.
*/
-asmlinkage void __kprobes do_page_fault(struct pt_regs *regs, unsigned long write,
- unsigned long address)
+static void __kprobes __do_page_fault(struct pt_regs *regs, unsigned long write,
+ unsigned long address)
{
struct vm_area_struct * vma = NULL;
struct task_struct *tsk = current;
}
#endif
}
+
+asmlinkage void __kprobes do_page_fault(struct pt_regs *regs,
+ unsigned long write, unsigned long address)
+{
+ enum ctx_state prev_state;
+
+ prev_state = exception_enter();
+ __do_page_fault(regs, write, address);
+ exception_exit(prev_state);
+}
uasm_i_cache(buf, Create_Dirty_Excl_D, off, A0);
}
- }
+ }
}
extern u32 __clear_page_start;
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Micro-assembler generated tlb handler functions.
+ *
+ * Copyright (C) 2013 Broadcom Corporation.
+ *
+ * Based on mm/page-funcs.c
+ * Copyright (C) 2012 MIPS Technologies, Inc.
+ * Copyright (C) 2012 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <asm/asm.h>
+#include <asm/regdef.h>
+
+#define FASTPATH_SIZE 128
+
+LEAF(tlbmiss_handler_setup_pgd)
+ .space 16 * 4
+END(tlbmiss_handler_setup_pgd)
+EXPORT(tlbmiss_handler_setup_pgd_end)
+
+LEAF(handle_tlbm)
+ .space FASTPATH_SIZE * 4
+END(handle_tlbm)
+EXPORT(handle_tlbm_end)
+
+LEAF(handle_tlbs)
+ .space FASTPATH_SIZE * 4
+END(handle_tlbs)
+EXPORT(handle_tlbs_end)
+
+LEAF(handle_tlbl)
+ .space FASTPATH_SIZE * 4
+END(handle_tlbl)
+EXPORT(handle_tlbl_end)
static unsigned int kscratch_used_mask __cpuinitdata;
+static inline int __maybe_unused c0_kscratch(void)
+{
+ switch (current_cpu_type()) {
+ case CPU_XLP:
+ case CPU_XLR:
+ return 22;
+ default:
+ return 31;
+ }
+}
+
static int __cpuinit allocate_kscratch(void)
{
int r;
int smp_processor_id_sel;
int smp_processor_id_shift;
- if (scratch_reg > 0) {
+ if (scratch_reg >= 0) {
/* Save in CPU local C0_KScratch? */
- UASM_i_MTC0(p, 1, 31, scratch_reg);
+ UASM_i_MTC0(p, 1, c0_kscratch(), scratch_reg);
r.r1 = K0;
r.r2 = K1;
r.r3 = 1;
static void __cpuinit build_restore_work_registers(u32 **p)
{
- if (scratch_reg > 0) {
- UASM_i_MFC0(p, 1, 31, scratch_reg);
+ if (scratch_reg >= 0) {
+ UASM_i_MFC0(p, 1, c0_kscratch(), scratch_reg);
return;
}
/* K0 already points to save area, restore $1 and $2 */
uasm_i_mtc0(p, 0, C0_PAGEMASK);
uasm_il_b(p, r, lid);
}
- if (scratch_reg > 0)
- UASM_i_MFC0(p, 1, 31, scratch_reg);
+ if (scratch_reg >= 0)
+ UASM_i_MFC0(p, 1, c0_kscratch(), scratch_reg);
else
UASM_i_LW(p, 1, scratchpad_offset(0), 0);
} else {
#ifdef CONFIG_MIPS_PGD_C0_CONTEXT
if (pgd_reg != -1) {
/* pgd is in pgd_reg */
- UASM_i_MFC0(p, ptr, 31, pgd_reg);
+ UASM_i_MFC0(p, ptr, c0_kscratch(), pgd_reg);
} else {
/*
* &pgd << 11 stored in CONTEXT [23..63].
uasm_i_jr(p, ptr);
if (mode == refill_scratch) {
- if (scratch_reg > 0)
- UASM_i_MFC0(p, 1, 31, scratch_reg);
+ if (scratch_reg >= 0)
+ UASM_i_MFC0(p, 1, c0_kscratch(), scratch_reg);
else
UASM_i_LW(p, 1, scratchpad_offset(0), 0);
} else {
uasm_i_srl(p, ptr, ptr, 19);
#else
/*
- * smp_processor_id() << 3 is stored in CONTEXT.
+ * smp_processor_id() << 2 is stored in CONTEXT.
*/
uasm_i_mfc0(p, ptr, C0_CONTEXT);
UASM_i_LA_mostly(p, tmp, pgdc);
static struct mips_huge_tlb_info __cpuinit
build_fast_tlb_refill_handler (u32 **p, struct uasm_label **l,
struct uasm_reloc **r, unsigned int tmp,
- unsigned int ptr, int c0_scratch)
+ unsigned int ptr, int c0_scratch_reg)
{
struct mips_huge_tlb_info rv;
unsigned int even, odd;
UASM_i_MFC0(p, tmp, C0_BADVADDR);
if (pgd_reg != -1)
- UASM_i_MFC0(p, ptr, 31, pgd_reg);
+ UASM_i_MFC0(p, ptr, c0_kscratch(), pgd_reg);
else
UASM_i_MFC0(p, ptr, C0_CONTEXT);
- if (c0_scratch >= 0)
- UASM_i_MTC0(p, scratch, 31, c0_scratch);
+ if (c0_scratch_reg >= 0)
+ UASM_i_MTC0(p, scratch, c0_kscratch(), c0_scratch_reg);
else
UASM_i_SW(p, scratch, scratchpad_offset(0), 0);
}
} else {
if (pgd_reg != -1)
- UASM_i_MFC0(p, ptr, 31, pgd_reg);
+ UASM_i_MFC0(p, ptr, c0_kscratch(), pgd_reg);
else
UASM_i_MFC0(p, ptr, C0_CONTEXT);
UASM_i_MFC0(p, tmp, C0_BADVADDR);
- if (c0_scratch >= 0)
- UASM_i_MTC0(p, scratch, 31, c0_scratch);
+ if (c0_scratch_reg >= 0)
+ UASM_i_MTC0(p, scratch, c0_kscratch(), c0_scratch_reg);
else
UASM_i_SW(p, scratch, scratchpad_offset(0), 0);
}
UASM_i_MTC0(p, odd, C0_ENTRYLO1); /* load it */
- if (c0_scratch >= 0) {
- UASM_i_MFC0(p, scratch, 31, c0_scratch);
+ if (c0_scratch_reg >= 0) {
+ UASM_i_MFC0(p, scratch, c0_kscratch(), c0_scratch_reg);
build_tlb_write_entry(p, l, r, tlb_random);
uasm_l_leave(l, *p);
rv.restore_scratch = 1;
memset(relocs, 0, sizeof(relocs));
memset(final_handler, 0, sizeof(final_handler));
- if ((scratch_reg > 0 || scratchpad_available()) && use_bbit_insns()) {
+ if ((scratch_reg >= 0 || scratchpad_available()) && use_bbit_insns()) {
htlb_info = build_fast_tlb_refill_handler(&p, &l, &r, K0, K1,
scratch_reg);
vmalloc_mode = refill_scratch;
dump_handler("r4000_tlb_refill", (u32 *)ebase, 64);
}
-/*
- * 128 instructions for the fastpath handler is generous and should
- * never be exceeded.
- */
-#define FASTPATH_SIZE 128
+extern u32 handle_tlbl[], handle_tlbl_end[];
+extern u32 handle_tlbs[], handle_tlbs_end[];
+extern u32 handle_tlbm[], handle_tlbm_end[];
-u32 handle_tlbl[FASTPATH_SIZE] __cacheline_aligned;
-u32 handle_tlbs[FASTPATH_SIZE] __cacheline_aligned;
-u32 handle_tlbm[FASTPATH_SIZE] __cacheline_aligned;
#ifdef CONFIG_MIPS_PGD_C0_CONTEXT
-u32 tlbmiss_handler_setup_pgd_array[16] __cacheline_aligned;
+extern u32 tlbmiss_handler_setup_pgd[], tlbmiss_handler_setup_pgd_end[];
static void __cpuinit build_r4000_setup_pgd(void)
{
const int a0 = 4;
const int a1 = 5;
u32 *p = tlbmiss_handler_setup_pgd_array;
+ const int tlbmiss_handler_setup_pgd_size =
+ tlbmiss_handler_setup_pgd_end - tlbmiss_handler_setup_pgd;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
- memset(tlbmiss_handler_setup_pgd_array, 0, sizeof(tlbmiss_handler_setup_pgd_array));
+ memset(tlbmiss_handler_setup_pgd, 0, tlbmiss_handler_setup_pgd_size *
+ sizeof(tlbmiss_handler_setup_pgd[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
} else {
/* PGD in c0_KScratch */
uasm_i_jr(&p, 31);
- UASM_i_MTC0(&p, a0, 31, pgd_reg);
+ UASM_i_MTC0(&p, a0, c0_kscratch(), pgd_reg);
}
- if (p - tlbmiss_handler_setup_pgd_array > ARRAY_SIZE(tlbmiss_handler_setup_pgd_array))
- panic("tlbmiss_handler_setup_pgd_array space exceeded");
+ if (p >= tlbmiss_handler_setup_pgd_end)
+ panic("tlbmiss_handler_setup_pgd space exceeded");
+
uasm_resolve_relocs(relocs, labels);
- pr_debug("Wrote tlbmiss_handler_setup_pgd_array (%u instructions).\n",
- (unsigned int)(p - tlbmiss_handler_setup_pgd_array));
+ pr_debug("Wrote tlbmiss_handler_setup_pgd (%u instructions).\n",
+ (unsigned int)(p - tlbmiss_handler_setup_pgd));
- dump_handler("tlbmiss_handler",
- tlbmiss_handler_setup_pgd_array,
- ARRAY_SIZE(tlbmiss_handler_setup_pgd_array));
+ dump_handler("tlbmiss_handler", tlbmiss_handler_setup_pgd,
+ tlbmiss_handler_setup_pgd_size);
}
#endif
static void __cpuinit build_r3000_tlb_load_handler(void)
{
u32 *p = handle_tlbl;
+ const int handle_tlbl_size = handle_tlbl_end - handle_tlbl;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
- memset(handle_tlbl, 0, sizeof(handle_tlbl));
+ memset(handle_tlbl, 0, handle_tlbl_size * sizeof(handle_tlbl[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
uasm_i_j(&p, (unsigned long)tlb_do_page_fault_0 & 0x0fffffff);
uasm_i_nop(&p);
- if ((p - handle_tlbl) > FASTPATH_SIZE)
+ if (p >= handle_tlbl_end)
panic("TLB load handler fastpath space exceeded");
uasm_resolve_relocs(relocs, labels);
pr_debug("Wrote TLB load handler fastpath (%u instructions).\n",
(unsigned int)(p - handle_tlbl));
- dump_handler("r3000_tlb_load", handle_tlbl, ARRAY_SIZE(handle_tlbl));
+ dump_handler("r3000_tlb_load", handle_tlbl, handle_tlbl_size);
}
static void __cpuinit build_r3000_tlb_store_handler(void)
{
u32 *p = handle_tlbs;
+ const int handle_tlbs_size = handle_tlbs_end - handle_tlbs;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
- memset(handle_tlbs, 0, sizeof(handle_tlbs));
+ memset(handle_tlbs, 0, handle_tlbs_size * sizeof(handle_tlbs[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
uasm_i_nop(&p);
- if ((p - handle_tlbs) > FASTPATH_SIZE)
+ if (p >= handle_tlbs)
panic("TLB store handler fastpath space exceeded");
uasm_resolve_relocs(relocs, labels);
pr_debug("Wrote TLB store handler fastpath (%u instructions).\n",
(unsigned int)(p - handle_tlbs));
- dump_handler("r3000_tlb_store", handle_tlbs, ARRAY_SIZE(handle_tlbs));
+ dump_handler("r3000_tlb_store", handle_tlbs, handle_tlbs_size);
}
static void __cpuinit build_r3000_tlb_modify_handler(void)
{
u32 *p = handle_tlbm;
+ const int handle_tlbm_size = handle_tlbm_end - handle_tlbm;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
- memset(handle_tlbm, 0, sizeof(handle_tlbm));
+ memset(handle_tlbm, 0, handle_tlbm_size * sizeof(handle_tlbm[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
uasm_i_nop(&p);
- if ((p - handle_tlbm) > FASTPATH_SIZE)
+ if (p >= handle_tlbm_end)
panic("TLB modify handler fastpath space exceeded");
uasm_resolve_relocs(relocs, labels);
pr_debug("Wrote TLB modify handler fastpath (%u instructions).\n",
(unsigned int)(p - handle_tlbm));
- dump_handler("r3000_tlb_modify", handle_tlbm, ARRAY_SIZE(handle_tlbm));
+ dump_handler("r3000_tlb_modify", handle_tlbm, handle_tlbm_size);
}
#endif /* CONFIG_MIPS_PGD_C0_CONTEXT */
static void __cpuinit build_r4000_tlb_load_handler(void)
{
u32 *p = handle_tlbl;
+ const int handle_tlbl_size = handle_tlbl_end - handle_tlbl;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
struct work_registers wr;
- memset(handle_tlbl, 0, sizeof(handle_tlbl));
+ memset(handle_tlbl, 0, handle_tlbl_size * sizeof(handle_tlbl[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
uasm_i_nop(&p);
uasm_i_tlbr(&p);
+
+ switch (current_cpu_type()) {
+ default:
+ if (cpu_has_mips_r2) {
+ uasm_i_ehb(&p);
+
+ case CPU_CAVIUM_OCTEON:
+ case CPU_CAVIUM_OCTEON_PLUS:
+ case CPU_CAVIUM_OCTEON2:
+ break;
+ }
+ }
+
/* Examine entrylo 0 or 1 based on ptr. */
if (use_bbit_insns()) {
uasm_i_bbit0(&p, wr.r2, ilog2(sizeof(pte_t)), 8);
uasm_i_nop(&p);
uasm_i_tlbr(&p);
+
+ switch (current_cpu_type()) {
+ default:
+ if (cpu_has_mips_r2) {
+ uasm_i_ehb(&p);
+
+ case CPU_CAVIUM_OCTEON:
+ case CPU_CAVIUM_OCTEON_PLUS:
+ case CPU_CAVIUM_OCTEON2:
+ break;
+ }
+ }
+
/* Examine entrylo 0 or 1 based on ptr. */
if (use_bbit_insns()) {
uasm_i_bbit0(&p, wr.r2, ilog2(sizeof(pte_t)), 8);
uasm_i_j(&p, (unsigned long)tlb_do_page_fault_0 & 0x0fffffff);
uasm_i_nop(&p);
- if ((p - handle_tlbl) > FASTPATH_SIZE)
+ if (p >= handle_tlbl_end)
panic("TLB load handler fastpath space exceeded");
uasm_resolve_relocs(relocs, labels);
pr_debug("Wrote TLB load handler fastpath (%u instructions).\n",
(unsigned int)(p - handle_tlbl));
- dump_handler("r4000_tlb_load", handle_tlbl, ARRAY_SIZE(handle_tlbl));
+ dump_handler("r4000_tlb_load", handle_tlbl, handle_tlbl_size);
}
static void __cpuinit build_r4000_tlb_store_handler(void)
{
u32 *p = handle_tlbs;
+ const int handle_tlbs_size = handle_tlbs_end - handle_tlbs;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
struct work_registers wr;
- memset(handle_tlbs, 0, sizeof(handle_tlbs));
+ memset(handle_tlbs, 0, handle_tlbs_size * sizeof(handle_tlbs[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
uasm_i_nop(&p);
- if ((p - handle_tlbs) > FASTPATH_SIZE)
+ if (p >= handle_tlbs_end)
panic("TLB store handler fastpath space exceeded");
uasm_resolve_relocs(relocs, labels);
pr_debug("Wrote TLB store handler fastpath (%u instructions).\n",
(unsigned int)(p - handle_tlbs));
- dump_handler("r4000_tlb_store", handle_tlbs, ARRAY_SIZE(handle_tlbs));
+ dump_handler("r4000_tlb_store", handle_tlbs, handle_tlbs_size);
}
static void __cpuinit build_r4000_tlb_modify_handler(void)
{
u32 *p = handle_tlbm;
+ const int handle_tlbm_size = handle_tlbm_end - handle_tlbm;
struct uasm_label *l = labels;
struct uasm_reloc *r = relocs;
struct work_registers wr;
- memset(handle_tlbm, 0, sizeof(handle_tlbm));
+ memset(handle_tlbm, 0, handle_tlbm_size * sizeof(handle_tlbm[0]));
memset(labels, 0, sizeof(labels));
memset(relocs, 0, sizeof(relocs));
uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
uasm_i_nop(&p);
- if ((p - handle_tlbm) > FASTPATH_SIZE)
+ if (p >= handle_tlbm_end)
panic("TLB modify handler fastpath space exceeded");
uasm_resolve_relocs(relocs, labels);
pr_debug("Wrote TLB modify handler fastpath (%u instructions).\n",
(unsigned int)(p - handle_tlbm));
- dump_handler("r4000_tlb_modify", handle_tlbm, ARRAY_SIZE(handle_tlbm));
+ dump_handler("r4000_tlb_modify", handle_tlbm, handle_tlbm_size);
+}
+
+static void __cpuinit flush_tlb_handlers(void)
+{
+ local_flush_icache_range((unsigned long)handle_tlbl,
+ (unsigned long)handle_tlbl_end);
+ local_flush_icache_range((unsigned long)handle_tlbs,
+ (unsigned long)handle_tlbs_end);
+ local_flush_icache_range((unsigned long)handle_tlbm,
+ (unsigned long)handle_tlbm_end);
+#ifdef CONFIG_MIPS_PGD_C0_CONTEXT
+ local_flush_icache_range((unsigned long)tlbmiss_handler_setup_pgd,
+ (unsigned long)tlbmiss_handler_setup_pgd_end);
+#endif
}
void __cpuinit build_tlb_refill_handler(void)
build_r3000_tlb_load_handler();
build_r3000_tlb_store_handler();
build_r3000_tlb_modify_handler();
+ flush_tlb_handlers();
run_once++;
}
#else
build_r4000_tlb_modify_handler();
if (!cpu_has_local_ebase)
build_r4000_tlb_refill_handler();
+ flush_tlb_handlers();
run_once++;
}
if (cpu_has_local_ebase)
build_r4000_tlb_refill_handler();
}
}
-
-void __cpuinit flush_tlb_handlers(void)
-{
- local_flush_icache_range((unsigned long)handle_tlbl,
- (unsigned long)handle_tlbl + sizeof(handle_tlbl));
- local_flush_icache_range((unsigned long)handle_tlbs,
- (unsigned long)handle_tlbs + sizeof(handle_tlbs));
- local_flush_icache_range((unsigned long)handle_tlbm,
- (unsigned long)handle_tlbm + sizeof(handle_tlbm));
-#ifdef CONFIG_MIPS_PGD_C0_CONTEXT
- local_flush_icache_range((unsigned long)tlbmiss_handler_setup_pgd_array,
- (unsigned long)tlbmiss_handler_setup_pgd_array + sizeof(handle_tlbm));
-#endif
-}
malta-reset.o malta-setup.o malta-time.o
obj-$(CONFIG_EARLY_PRINTK) += malta-console.o
-obj-$(CONFIG_PCI) += malta-pci.o
# FIXME FIXME FIXME
obj-$(CONFIG_MIPS_MT_SMTC) += malta-smtc.o
*/
int __init gcmp_probe(unsigned long addr, unsigned long size)
{
- if (mips_revision_sconid != MIPS_REVISION_SCON_ROCIT) {
+ if ((mips_revision_sconid != MIPS_REVISION_SCON_ROCIT) &&
+ (mips_revision_sconid != MIPS_REVISION_SCON_GT64120)) {
gcmp_present = 0;
+ pr_debug("GCMP NOT present\n");
return gcmp_present;
}
+++ /dev/null
-/*
- * Copyright (C) 1999, 2000, 2004, 2005 MIPS Technologies, Inc.
- * All rights reserved.
- * Authors: Carsten Langgaard <carstenl@mips.com>
- * Maciej W. Rozycki <macro@mips.com>
- *
- * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * MIPS boards specific PCI support.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <asm/gt64120.h>
-#include <asm/gcmpregs.h>
-#include <asm/mips-boards/generic.h>
-#include <asm/mips-boards/bonito64.h>
-#include <asm/mips-boards/msc01_pci.h>
-
-static struct resource bonito64_mem_resource = {
- .name = "Bonito PCI MEM",
- .flags = IORESOURCE_MEM,
-};
-
-static struct resource bonito64_io_resource = {
- .name = "Bonito PCI I/O",
- .start = 0x00000000UL,
- .end = 0x000fffffUL,
- .flags = IORESOURCE_IO,
-};
-
-static struct resource gt64120_mem_resource = {
- .name = "GT-64120 PCI MEM",
- .flags = IORESOURCE_MEM,
-};
-
-static struct resource gt64120_io_resource = {
- .name = "GT-64120 PCI I/O",
- .flags = IORESOURCE_IO,
-};
-
-static struct resource msc_mem_resource = {
- .name = "MSC PCI MEM",
- .flags = IORESOURCE_MEM,
-};
-
-static struct resource msc_io_resource = {
- .name = "MSC PCI I/O",
- .flags = IORESOURCE_IO,
-};
-
-extern struct pci_ops bonito64_pci_ops;
-extern struct pci_ops gt64xxx_pci0_ops;
-extern struct pci_ops msc_pci_ops;
-
-static struct pci_controller bonito64_controller = {
- .pci_ops = &bonito64_pci_ops,
- .io_resource = &bonito64_io_resource,
- .mem_resource = &bonito64_mem_resource,
- .io_offset = 0x00000000UL,
-};
-
-static struct pci_controller gt64120_controller = {
- .pci_ops = >64xxx_pci0_ops,
- .io_resource = >64120_io_resource,
- .mem_resource = >64120_mem_resource,
-};
-
-static struct pci_controller msc_controller = {
- .pci_ops = &msc_pci_ops,
- .io_resource = &msc_io_resource,
- .mem_resource = &msc_mem_resource,
-};
-
-void __init mips_pcibios_init(void)
-{
- struct pci_controller *controller;
- resource_size_t start, end, map, start1, end1, map1, map2, map3, mask;
-
- switch (mips_revision_sconid) {
- case MIPS_REVISION_SCON_GT64120:
- /*
- * Due to a bug in the Galileo system controller, we need
- * to setup the PCI BAR for the Galileo internal registers.
- * This should be done in the bios/bootprom and will be
- * fixed in a later revision of YAMON (the MIPS boards
- * boot prom).
- */
- GT_WRITE(GT_PCI0_CFGADDR_OFS,
- (0 << GT_PCI0_CFGADDR_BUSNUM_SHF) | /* Local bus */
- (0 << GT_PCI0_CFGADDR_DEVNUM_SHF) | /* GT64120 dev */
- (0 << GT_PCI0_CFGADDR_FUNCTNUM_SHF) | /* Function 0*/
- ((0x20/4) << GT_PCI0_CFGADDR_REGNUM_SHF) | /* BAR 4*/
- GT_PCI0_CFGADDR_CONFIGEN_BIT);
-
- /* Perform the write */
- GT_WRITE(GT_PCI0_CFGDATA_OFS, CPHYSADDR(MIPS_GT_BASE));
-
- /* Set up resource ranges from the controller's registers. */
- start = GT_READ(GT_PCI0M0LD_OFS);
- end = GT_READ(GT_PCI0M0HD_OFS);
- map = GT_READ(GT_PCI0M0REMAP_OFS);
- end = (end & GT_PCI_HD_MSK) | (start & ~GT_PCI_HD_MSK);
- start1 = GT_READ(GT_PCI0M1LD_OFS);
- end1 = GT_READ(GT_PCI0M1HD_OFS);
- map1 = GT_READ(GT_PCI0M1REMAP_OFS);
- end1 = (end1 & GT_PCI_HD_MSK) | (start1 & ~GT_PCI_HD_MSK);
- /* Cannot support multiple windows, use the wider. */
- if (end1 - start1 > end - start) {
- start = start1;
- end = end1;
- map = map1;
- }
- mask = ~(start ^ end);
- /* We don't support remapping with a discontiguous mask. */
- BUG_ON((start & GT_PCI_HD_MSK) != (map & GT_PCI_HD_MSK) &&
- mask != ~((mask & -mask) - 1));
- gt64120_mem_resource.start = start;
- gt64120_mem_resource.end = end;
- gt64120_controller.mem_offset = (start & mask) - (map & mask);
- /* Addresses are 36-bit, so do shifts in the destinations. */
- gt64120_mem_resource.start <<= GT_PCI_DCRM_SHF;
- gt64120_mem_resource.end <<= GT_PCI_DCRM_SHF;
- gt64120_mem_resource.end |= (1 << GT_PCI_DCRM_SHF) - 1;
- gt64120_controller.mem_offset <<= GT_PCI_DCRM_SHF;
-
- start = GT_READ(GT_PCI0IOLD_OFS);
- end = GT_READ(GT_PCI0IOHD_OFS);
- map = GT_READ(GT_PCI0IOREMAP_OFS);
- end = (end & GT_PCI_HD_MSK) | (start & ~GT_PCI_HD_MSK);
- mask = ~(start ^ end);
- /* We don't support remapping with a discontiguous mask. */
- BUG_ON((start & GT_PCI_HD_MSK) != (map & GT_PCI_HD_MSK) &&
- mask != ~((mask & -mask) - 1));
- gt64120_io_resource.start = map & mask;
- gt64120_io_resource.end = (map & mask) | ~mask;
- gt64120_controller.io_offset = 0;
- /* Addresses are 36-bit, so do shifts in the destinations. */
- gt64120_io_resource.start <<= GT_PCI_DCRM_SHF;
- gt64120_io_resource.end <<= GT_PCI_DCRM_SHF;
- gt64120_io_resource.end |= (1 << GT_PCI_DCRM_SHF) - 1;
-
- controller = >64120_controller;
- break;
-
- case MIPS_REVISION_SCON_BONITO:
- /* Set up resource ranges from the controller's registers. */
- map = BONITO_PCIMAP;
- map1 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO0) >>
- BONITO_PCIMAP_PCIMAP_LO0_SHIFT;
- map2 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO1) >>
- BONITO_PCIMAP_PCIMAP_LO1_SHIFT;
- map3 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO2) >>
- BONITO_PCIMAP_PCIMAP_LO2_SHIFT;
- /* Combine as many adjacent windows as possible. */
- map = map1;
- start = BONITO_PCILO0_BASE;
- end = 1;
- if (map3 == map2 + 1) {
- map = map2;
- start = BONITO_PCILO1_BASE;
- end++;
- }
- if (map2 == map1 + 1) {
- map = map1;
- start = BONITO_PCILO0_BASE;
- end++;
- }
- bonito64_mem_resource.start = start;
- bonito64_mem_resource.end = start +
- BONITO_PCIMAP_WINBASE(end) - 1;
- bonito64_controller.mem_offset = start -
- BONITO_PCIMAP_WINBASE(map);
-
- controller = &bonito64_controller;
- break;
-
- case MIPS_REVISION_SCON_SOCIT:
- case MIPS_REVISION_SCON_ROCIT:
- case MIPS_REVISION_SCON_SOCITSC:
- case MIPS_REVISION_SCON_SOCITSCP:
- /* Set up resource ranges from the controller's registers. */
- MSC_READ(MSC01_PCI_SC2PMBASL, start);
- MSC_READ(MSC01_PCI_SC2PMMSKL, mask);
- MSC_READ(MSC01_PCI_SC2PMMAPL, map);
- msc_mem_resource.start = start & mask;
- msc_mem_resource.end = (start & mask) | ~mask;
- msc_controller.mem_offset = (start & mask) - (map & mask);
-#ifdef CONFIG_MIPS_CMP
- if (gcmp_niocu())
- gcmp_setregion(0, start, mask,
- GCMP_GCB_GCMPB_CMDEFTGT_IOCU1);
-#endif
- MSC_READ(MSC01_PCI_SC2PIOBASL, start);
- MSC_READ(MSC01_PCI_SC2PIOMSKL, mask);
- MSC_READ(MSC01_PCI_SC2PIOMAPL, map);
- msc_io_resource.start = map & mask;
- msc_io_resource.end = (map & mask) | ~mask;
- msc_controller.io_offset = 0;
- ioport_resource.end = ~mask;
-#ifdef CONFIG_MIPS_CMP
- if (gcmp_niocu())
- gcmp_setregion(1, start, mask,
- GCMP_GCB_GCMPB_CMDEFTGT_IOCU1);
-#endif
- /* If ranges overlap I/O takes precedence. */
- start = start & mask;
- end = start | ~mask;
- if ((start >= msc_mem_resource.start &&
- start <= msc_mem_resource.end) ||
- (end >= msc_mem_resource.start &&
- end <= msc_mem_resource.end)) {
- /* Use the larger space. */
- start = max(start, msc_mem_resource.start);
- end = min(end, msc_mem_resource.end);
- if (start - msc_mem_resource.start >=
- msc_mem_resource.end - end)
- msc_mem_resource.end = start - 1;
- else
- msc_mem_resource.start = end + 1;
- }
-
- controller = &msc_controller;
- break;
- default:
- return;
- }
-
- /* Change start address to avoid conflicts with ACPI and SMB devices */
- if (controller->io_resource->start < 0x00002000UL)
- controller->io_resource->start = 0x00002000UL;
-
- iomem_resource.end &= 0xfffffffffULL; /* 64 GB */
- ioport_resource.end = controller->io_resource->end;
-
- controller->io_map_base = mips_io_port_base;
-
- register_pci_controller(controller);
-}
/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
* Carsten Langgaard, carstenl@mips.com
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- * Reset the MIPS boards.
- *
*/
-#include <linux/init.h>
+#include <linux/io.h>
#include <linux/pm.h>
-#include <asm/io.h>
#include <asm/reboot.h>
-#include <asm/mips-boards/generic.h>
+
+#define SOFTRES_REG 0x1f000500
+#define GORESET 0x42
static void mips_machine_restart(char *command)
{
__raw_writel(GORESET, softres_reg);
}
-
static int __init mips_reboot_setup(void)
{
_machine_restart = mips_machine_restart;
return 0;
}
-
arch_initcall(mips_reboot_setup);
#include <linux/pm.h>
#include <asm/reboot.h>
-#include <asm/mips-boards/generic.h>
+
+#define SOFTRES_REG 0x1f000050
+#define GORESET 0x4d
static void mips_machine_restart(char *command)
{
return 0;
}
-
arch_initcall(mips_reboot_setup);
config NLM_COMMON
bool
+config IOMMU_HELPER
+ bool
+
+config NEED_SG_DMA_LENGTH
+ bool
+
+config SWIOTLB
+ def_bool y
+ select NEED_SG_DMA_LENGTH
+ select IOMMU_HELPER
+
endif
obj-y += irq.o time.o
+obj-y += nlm-dma.o
+obj-y += reset.o
obj-$(CONFIG_SMP) += smp.o smpboot.o
obj-$(CONFIG_EARLY_PRINTK) += earlycons.o
node = nlm_nodeid();
eirr = read_c0_eirr_and_eimr();
-
- i = __ilog2_u64(eirr);
- if (i == -1)
+ if (eirr == 0)
return;
+ i = __ffs64(eirr);
/* per-CPU IRQs don't need translation */
- if (eirr & PERCPU_IRQ_MASK) {
+ if (i < PIC_IRQ_BASE) {
do_IRQ(i);
return;
}
--- /dev/null
+/*
+* Copyright (C) 2003-2013 Broadcom Corporation
+* All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+#include <linux/bootmem.h>
+#include <linux/export.h>
+#include <linux/swiotlb.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+
+#include <asm/bootinfo.h>
+
+static char *nlm_swiotlb;
+
+static void *nlm_dma_alloc_coherent(struct device *dev, size_t size,
+ dma_addr_t *dma_handle, gfp_t gfp, struct dma_attrs *attrs)
+{
+ void *ret;
+
+ if (dma_alloc_from_coherent(dev, size, dma_handle, &ret))
+ return ret;
+
+ /* ignore region specifiers */
+ gfp &= ~(__GFP_DMA | __GFP_DMA32 | __GFP_HIGHMEM);
+
+#ifdef CONFIG_ZONE_DMA32
+ if (dev->coherent_dma_mask <= DMA_BIT_MASK(32))
+ gfp |= __GFP_DMA32;
+#endif
+
+ /* Don't invoke OOM killer */
+ gfp |= __GFP_NORETRY;
+
+ return swiotlb_alloc_coherent(dev, size, dma_handle, gfp);
+}
+
+static void nlm_dma_free_coherent(struct device *dev, size_t size,
+ void *vaddr, dma_addr_t dma_handle, struct dma_attrs *attrs)
+{
+ int order = get_order(size);
+
+ if (dma_release_from_coherent(dev, order, vaddr))
+ return;
+
+ swiotlb_free_coherent(dev, size, vaddr, dma_handle);
+}
+
+struct dma_map_ops nlm_swiotlb_dma_ops = {
+ .alloc = nlm_dma_alloc_coherent,
+ .free = nlm_dma_free_coherent,
+ .map_page = swiotlb_map_page,
+ .unmap_page = swiotlb_unmap_page,
+ .map_sg = swiotlb_map_sg_attrs,
+ .unmap_sg = swiotlb_unmap_sg_attrs,
+ .sync_single_for_cpu = swiotlb_sync_single_for_cpu,
+ .sync_single_for_device = swiotlb_sync_single_for_device,
+ .sync_sg_for_cpu = swiotlb_sync_sg_for_cpu,
+ .sync_sg_for_device = swiotlb_sync_sg_for_device,
+ .mapping_error = swiotlb_dma_mapping_error,
+ .dma_supported = swiotlb_dma_supported
+};
+
+void __init plat_swiotlb_setup(void)
+{
+ size_t swiotlbsize;
+ unsigned long swiotlb_nslabs;
+
+ swiotlbsize = 1 << 20; /* 1 MB for now */
+ swiotlb_nslabs = swiotlbsize >> IO_TLB_SHIFT;
+ swiotlb_nslabs = ALIGN(swiotlb_nslabs, IO_TLB_SEGSIZE);
+ swiotlbsize = swiotlb_nslabs << IO_TLB_SHIFT;
+
+ nlm_swiotlb = alloc_bootmem_low_pages(swiotlbsize);
+ swiotlb_init_with_tbl(nlm_swiotlb, swiotlb_nslabs, 1);
+}
--- /dev/null
+/*
+ * Copyright 2003-2013 Broadcom Corporation.
+ * All Rights Reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/init.h>
+
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/asmmacro.h>
+#include <asm/addrspace.h>
+
+#include <asm/netlogic/common.h>
+
+#include <asm/netlogic/xlp-hal/iomap.h>
+#include <asm/netlogic/xlp-hal/xlp.h>
+#include <asm/netlogic/xlp-hal/sys.h>
+#include <asm/netlogic/xlp-hal/cpucontrol.h>
+
+#define CP0_EBASE $15
+#define SYS_CPU_COHERENT_BASE(node) CKSEG1ADDR(XLP_DEFAULT_IO_BASE) + \
+ XLP_IO_SYS_OFFSET(node) + XLP_IO_PCI_HDRSZ + \
+ SYS_CPU_NONCOHERENT_MODE * 4
+
+/* Enable XLP features and workarounds in the LSU */
+.macro xlp_config_lsu
+ li t0, LSU_DEFEATURE
+ mfcr t1, t0
+
+ lui t2, 0xc080 /* SUE, Enable Unaligned Access, L2HPE */
+ or t1, t1, t2
+ mtcr t1, t0
+
+ li t0, ICU_DEFEATURE
+ mfcr t1, t0
+ ori t1, 0x1000 /* Enable Icache partitioning */
+ mtcr t1, t0
+
+ li t0, SCHED_DEFEATURE
+ lui t1, 0x0100 /* Disable BRU accepting ALU ops */
+ mtcr t1, t0
+.endm
+
+/*
+ * Low level flush for L1D cache on XLP, the normal cache ops does
+ * not do the complete and correct cache flush.
+ */
+.macro xlp_flush_l1_dcache
+ li t0, LSU_DEBUG_DATA0
+ li t1, LSU_DEBUG_ADDR
+ li t2, 0 /* index */
+ li t3, 0x1000 /* loop count */
+1:
+ sll v0, t2, 5
+ mtcr zero, t0
+ ori v1, v0, 0x3 /* way0 | write_enable | write_active */
+ mtcr v1, t1
+2:
+ mfcr v1, t1
+ andi v1, 0x1 /* wait for write_active == 0 */
+ bnez v1, 2b
+ nop
+ mtcr zero, t0
+ ori v1, v0, 0x7 /* way1 | write_enable | write_active */
+ mtcr v1, t1
+3:
+ mfcr v1, t1
+ andi v1, 0x1 /* wait for write_active == 0 */
+ bnez v1, 3b
+ nop
+ addi t2, 1
+ bne t3, t2, 1b
+ nop
+.endm
+
+/*
+ * nlm_reset_entry will be copied to the reset entry point for
+ * XLR and XLP. The XLP cores start here when they are woken up. This
+ * is also the NMI entry point.
+ *
+ * We use scratch reg 6/7 to save k0/k1 and check for NMI first.
+ *
+ * The data corresponding to reset/NMI is stored at RESET_DATA_PHYS
+ * location, this will have the thread mask (used when core is woken up)
+ * and the current NMI handler in case we reached here for an NMI.
+ *
+ * When a core or thread is newly woken up, it marks itself ready and
+ * loops in a 'wait'. When the CPU really needs waking up, we send an NMI
+ * IPI to it, with the NMI handler set to prom_boot_secondary_cpus
+ */
+ .set noreorder
+ .set noat
+ .set arch=xlr /* for mfcr/mtcr, XLR is sufficient */
+
+FEXPORT(nlm_reset_entry)
+ dmtc0 k0, $22, 6
+ dmtc0 k1, $22, 7
+ mfc0 k0, CP0_STATUS
+ li k1, 0x80000
+ and k1, k0, k1
+ beqz k1, 1f /* go to real reset entry */
+ nop
+ li k1, CKSEG1ADDR(RESET_DATA_PHYS) /* NMI */
+ ld k0, BOOT_NMI_HANDLER(k1)
+ jr k0
+ nop
+
+1: /* Entry point on core wakeup */
+ mfc0 t0, CP0_EBASE, 1
+ mfc0 t1, CP0_EBASE, 1
+ srl t1, 5
+ andi t1, 0x3 /* t1 <- node */
+ li t2, 0x40000
+ mul t3, t2, t1 /* t3 = node * 0x40000 */
+ srl t0, t0, 2
+ and t0, t0, 0x7 /* t0 <- core */
+ li t1, 0x1
+ sll t0, t1, t0
+ nor t0, t0, zero /* t0 <- ~(1 << core) */
+ li t2, SYS_CPU_COHERENT_BASE(0)
+ add t2, t2, t3 /* t2 <- SYS offset for node */
+ lw t1, 0(t2)
+ and t1, t1, t0
+ sw t1, 0(t2)
+
+ /* read back to ensure complete */
+ lw t1, 0(t2)
+ sync
+
+ /* Configure LSU on Non-0 Cores. */
+ xlp_config_lsu
+ /* FALL THROUGH */
+
+/*
+ * Wake up sibling threads from the initial thread in
+ * a core.
+ */
+EXPORT(nlm_boot_siblings)
+ /* core L1D flush before enable threads */
+ xlp_flush_l1_dcache
+ /* Enable hw threads by writing to MAP_THREADMODE of the core */
+ li t0, CKSEG1ADDR(RESET_DATA_PHYS)
+ lw t1, BOOT_THREAD_MODE(t0) /* t1 <- thread mode */
+ li t0, ((CPU_BLOCKID_MAP << 8) | MAP_THREADMODE)
+ mfcr t2, t0
+ or t2, t2, t1
+ mtcr t2, t0
+
+ /*
+ * The new hardware thread starts at the next instruction
+ * For all the cases other than core 0 thread 0, we will
+ * jump to the secondary wait function.
+ */
+ mfc0 v0, CP0_EBASE, 1
+ andi v0, 0x3ff /* v0 <- node/core */
+
+ beqz v0, 4f /* boot cpu (cpuid == 0)? */
+ nop
+
+ /* setup status reg */
+ move t1, zero
+#ifdef CONFIG_64BIT
+ ori t1, ST0_KX
+#endif
+ mtc0 t1, CP0_STATUS
+
+ /* mark CPU ready, careful here, previous mtcr trashed registers */
+ li t3, CKSEG1ADDR(RESET_DATA_PHYS)
+ ADDIU t1, t3, BOOT_CPU_READY
+ sll v1, v0, 2
+ PTR_ADDU t1, v1
+ li t2, 1
+ sw t2, 0(t1)
+ /* Wait until NMI hits */
+3: wait
+ b 3b
+ nop
+
+ /*
+ * For the boot CPU, we have to restore registers and
+ * return
+ */
+4: dmfc0 t0, $4, 2 /* restore SP from UserLocal */
+ li t1, 0xfadebeef
+ dmtc0 t1, $4, 2 /* restore SP from UserLocal */
+ PTR_SUBU sp, t0, PT_SIZE
+ RESTORE_ALL
+ jr ra
+ nop
+EXPORT(nlm_reset_entry_end)
+
+LEAF(nlm_init_boot_cpu)
+#ifdef CONFIG_CPU_XLP
+ xlp_config_lsu
+#endif
+ jr ra
+ nop
+END(nlm_init_boot_cpu)
* Boot all other cpus in the system, initialize them, and bring them into
* the boot function
*/
-int nlm_cpu_ready[NR_CPUS];
unsigned long nlm_next_gp;
unsigned long nlm_next_sp;
static cpumask_t phys_cpu_present_mask;
{
unsigned int boot_cpu;
int num_cpus, i, ncore;
+ volatile u32 *cpu_ready = nlm_get_boot_data(BOOT_CPU_READY);
char buf[64];
boot_cpu = hard_smp_processor_id();
num_cpus = 1;
for (i = 0; i < NR_CPUS; i++) {
/*
- * nlm_cpu_ready array is not set for the boot_cpu,
+ * cpu_ready array is not set for the boot_cpu,
* it is only set for ASPs (see smpboot.S)
*/
- if (nlm_cpu_ready[i]) {
+ if (cpu_ready[i]) {
cpumask_set_cpu(i, &phys_cpu_present_mask);
__cpu_number_map[i] = num_cpus;
__cpu_logical_map[num_cpus] = i;
int __cpuinit nlm_wakeup_secondary_cpus(void)
{
- unsigned long reset_vec;
- char *reset_data;
+ u32 *reset_data;
int threadmode;
- /* Update reset entry point with CPU init code */
- reset_vec = CKSEG1ADDR(RESET_VEC_PHYS);
- memcpy((void *)reset_vec, (void *)nlm_reset_entry,
- (nlm_reset_entry_end - nlm_reset_entry));
-
/* verify the mask and setup core config variables */
threadmode = nlm_parse_cpumask(&nlm_cpumask);
/* Setup CPU init parameters */
- reset_data = (char *)CKSEG1ADDR(RESET_DATA_PHYS);
- *(int *)(reset_data + BOOT_THREAD_MODE) = threadmode;
+ reset_data = nlm_get_boot_data(BOOT_THREAD_MODE);
+ *reset_data = threadmode;
#ifdef CONFIG_CPU_XLP
xlp_wakeup_secondary_cpus();
#include <asm/netlogic/xlp-hal/cpucontrol.h>
#define CP0_EBASE $15
-#define SYS_CPU_COHERENT_BASE(node) CKSEG1ADDR(XLP_DEFAULT_IO_BASE) + \
- XLP_IO_SYS_OFFSET(node) + XLP_IO_PCI_HDRSZ + \
- SYS_CPU_NONCOHERENT_MODE * 4
-
-#define XLP_AX_WORKAROUND /* enable Ax silicon workarounds */
-
-/* Enable XLP features and workarounds in the LSU */
-.macro xlp_config_lsu
- li t0, LSU_DEFEATURE
- mfcr t1, t0
-
- lui t2, 0xc080 /* SUE, Enable Unaligned Access, L2HPE */
- or t1, t1, t2
-#ifdef XLP_AX_WORKAROUND
- li t2, ~0xe /* S1RCM */
- and t1, t1, t2
-#endif
- mtcr t1, t0
-
- li t0, ICU_DEFEATURE
- mfcr t1, t0
- ori t1, 0x1000 /* Enable Icache partitioning */
- mtcr t1, t0
-
-
-#ifdef XLP_AX_WORKAROUND
- li t0, SCHED_DEFEATURE
- lui t1, 0x0100 /* Disable BRU accepting ALU ops */
- mtcr t1, t0
-#endif
-.endm
-
-/*
- * This is the code that will be copied to the reset entry point for
- * XLR and XLP. The XLP cores start here when they are woken up. This
- * is also the NMI entry point.
- */
-.macro xlp_flush_l1_dcache
- li t0, LSU_DEBUG_DATA0
- li t1, LSU_DEBUG_ADDR
- li t2, 0 /* index */
- li t3, 0x1000 /* loop count */
-1:
- sll v0, t2, 5
- mtcr zero, t0
- ori v1, v0, 0x3 /* way0 | write_enable | write_active */
- mtcr v1, t1
-2:
- mfcr v1, t1
- andi v1, 0x1 /* wait for write_active == 0 */
- bnez v1, 2b
- nop
- mtcr zero, t0
- ori v1, v0, 0x7 /* way1 | write_enable | write_active */
- mtcr v1, t1
-3:
- mfcr v1, t1
- andi v1, 0x1 /* wait for write_active == 0 */
- bnez v1, 3b
- nop
- addi t2, 1
- bne t3, t2, 1b
- nop
-.endm
-
-/*
- * The cores can come start when they are woken up. This is also the NMI
- * entry, so check that first.
- *
- * The data corresponding to reset/NMI is stored at RESET_DATA_PHYS
- * location, this will have the thread mask (used when core is woken up)
- * and the current NMI handler in case we reached here for an NMI.
- *
- * When a core or thread is newly woken up, it loops in a 'wait'. When
- * the CPU really needs waking up, we send an NMI to it, with the NMI
- * handler set to prom_boot_secondary_cpus
- */
.set noreorder
.set noat
- .set arch=xlr /* for mfcr/mtcr, XLR is sufficient */
-
-FEXPORT(nlm_reset_entry)
- dmtc0 k0, $22, 6
- dmtc0 k1, $22, 7
- mfc0 k0, CP0_STATUS
- li k1, 0x80000
- and k1, k0, k1
- beqz k1, 1f /* go to real reset entry */
- nop
- li k1, CKSEG1ADDR(RESET_DATA_PHYS) /* NMI */
- ld k0, BOOT_NMI_HANDLER(k1)
- jr k0
- nop
-
-1: /* Entry point on core wakeup */
- mfc0 t0, CP0_EBASE, 1
- mfc0 t1, CP0_EBASE, 1
- srl t1, 5
- andi t1, 0x3 /* t1 <- node */
- li t2, 0x40000
- mul t3, t2, t1 /* t3 = node * 0x40000 */
- srl t0, t0, 2
- and t0, t0, 0x7 /* t0 <- core */
- li t1, 0x1
- sll t0, t1, t0
- nor t0, t0, zero /* t0 <- ~(1 << core) */
- li t2, SYS_CPU_COHERENT_BASE(0)
- add t2, t2, t3 /* t2 <- SYS offset for node */
- lw t1, 0(t2)
- and t1, t1, t0
- sw t1, 0(t2)
-
- /* read back to ensure complete */
- lw t1, 0(t2)
- sync
-
- /* Configure LSU on Non-0 Cores. */
- xlp_config_lsu
- /* FALL THROUGH */
-
-/*
- * Wake up sibling threads from the initial thread in
- * a core.
- */
-EXPORT(nlm_boot_siblings)
- /* core L1D flush before enable threads */
- xlp_flush_l1_dcache
- /* Enable hw threads by writing to MAP_THREADMODE of the core */
- li t0, CKSEG1ADDR(RESET_DATA_PHYS)
- lw t1, BOOT_THREAD_MODE(t0) /* t1 <- thread mode */
- li t0, ((CPU_BLOCKID_MAP << 8) | MAP_THREADMODE)
- mfcr t2, t0
- or t2, t2, t1
- mtcr t2, t0
-
- /*
- * The new hardware thread starts at the next instruction
- * For all the cases other than core 0 thread 0, we will
- * jump to the secondary wait function.
- */
- mfc0 v0, CP0_EBASE, 1
- andi v0, 0x3ff /* v0 <- node/core */
-
- /* Init MMU in the first thread after changing THREAD_MODE
- * register (Ax Errata?)
- */
- andi v1, v0, 0x3 /* v1 <- thread id */
- bnez v1, 2f
- nop
-
- li t0, MMU_SETUP
- li t1, 0
- mtcr t1, t0
- _ehb
-
-2: beqz v0, 4f /* boot cpu (cpuid == 0)? */
- nop
-
- /* setup status reg */
- move t1, zero
-#ifdef CONFIG_64BIT
- ori t1, ST0_KX
-#endif
- mtc0 t1, CP0_STATUS
- /* mark CPU ready */
- PTR_LA t1, nlm_cpu_ready
- sll v1, v0, 2
- PTR_ADDU t1, v1
- li t2, 1
- sw t2, 0(t1)
- /* Wait until NMI hits */
-3: wait
- j 3b
- nop
-
- /*
- * For the boot CPU, we have to restore registers and
- * return
- */
-4: dmfc0 t0, $4, 2 /* restore SP from UserLocal */
- li t1, 0xfadebeef
- dmtc0 t1, $4, 2 /* restore SP from UserLocal */
- PTR_SUBU sp, t0, PT_SIZE
- RESTORE_ALL
- jr ra
- nop
-EXPORT(nlm_reset_entry_end)
+ .set arch=xlr /* for mfcr/mtcr, XLR is sufficient */
FEXPORT(xlp_boot_core0_siblings) /* "Master" cpu starts from here */
- xlp_config_lsu
dmtc0 sp, $4, 2 /* SP saved in UserLocal */
SAVE_ALL
sync
andi t2, t0, 0x3 /* thread num */
sll t0, 2 /* offset in cpu array */
- PTR_LA t1, nlm_cpu_ready /* mark CPU ready */
- PTR_ADDU t1, t0
+ li t3, CKSEG1ADDR(RESET_DATA_PHYS)
+ ADDIU t1, t3, BOOT_CPU_READY
+ ADDU t1, t0
li t3, 1
sw t3, 0(t1)
mtcr t1, t0 /* update core control */
1: wait
- j 1b
+ b 1b
nop
END(nlm_rmiboot_preboot)
__FINIT
-obj-y += setup.o nlm_hal.o
+obj-y += setup.o nlm_hal.o cop2-ex.o dt.o
obj-$(CONFIG_SMP) += wakeup.o
obj-$(CONFIG_USB) += usb-init.o
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2013 Broadcom Corporation.
+ *
+ * based on arch/mips/cavium-octeon/cpu.c
+ * Copyright (C) 2009 Wind River Systems,
+ * written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/init.h>
+#include <linux/irqflags.h>
+#include <linux/notifier.h>
+#include <linux/prefetch.h>
+#include <linux/sched.h>
+
+#include <asm/cop2.h>
+#include <asm/current.h>
+#include <asm/mipsregs.h>
+#include <asm/page.h>
+
+#include <asm/netlogic/mips-extns.h>
+
+/*
+ * 64 bit ops are done in inline assembly to support 32 bit
+ * compilation
+ */
+void nlm_cop2_save(struct nlm_cop2_state *r)
+{
+ asm volatile(
+ ".set push\n"
+ ".set noat\n"
+ "dmfc2 $1, $0, 0\n"
+ "sd $1, 0(%1)\n"
+ "dmfc2 $1, $0, 1\n"
+ "sd $1, 8(%1)\n"
+ "dmfc2 $1, $0, 2\n"
+ "sd $1, 16(%1)\n"
+ "dmfc2 $1, $0, 3\n"
+ "sd $1, 24(%1)\n"
+ "dmfc2 $1, $1, 0\n"
+ "sd $1, 0(%2)\n"
+ "dmfc2 $1, $1, 1\n"
+ "sd $1, 8(%2)\n"
+ "dmfc2 $1, $1, 2\n"
+ "sd $1, 16(%2)\n"
+ "dmfc2 $1, $1, 3\n"
+ "sd $1, 24(%2)\n"
+ ".set pop\n"
+ : "=m"(*r)
+ : "r"(r->tx), "r"(r->rx));
+
+ r->tx_msg_status = __read_32bit_c2_register($2, 0);
+ r->rx_msg_status = __read_32bit_c2_register($3, 0) & 0x0fffffff;
+}
+
+void nlm_cop2_restore(struct nlm_cop2_state *r)
+{
+ u32 rstat;
+
+ asm volatile(
+ ".set push\n"
+ ".set noat\n"
+ "ld $1, 0(%1)\n"
+ "dmtc2 $1, $0, 0\n"
+ "ld $1, 8(%1)\n"
+ "dmtc2 $1, $0, 1\n"
+ "ld $1, 16(%1)\n"
+ "dmtc2 $1, $0, 2\n"
+ "ld $1, 24(%1)\n"
+ "dmtc2 $1, $0, 3\n"
+ "ld $1, 0(%2)\n"
+ "dmtc2 $1, $1, 0\n"
+ "ld $1, 8(%2)\n"
+ "dmtc2 $1, $1, 1\n"
+ "ld $1, 16(%2)\n"
+ "dmtc2 $1, $1, 2\n"
+ "ld $1, 24(%2)\n"
+ "dmtc2 $1, $1, 3\n"
+ ".set pop\n"
+ : : "m"(*r), "r"(r->tx), "r"(r->rx));
+
+ __write_32bit_c2_register($2, 0, r->tx_msg_status);
+ rstat = __read_32bit_c2_register($3, 0) & 0xf0000000u;
+ __write_32bit_c2_register($3, 0, r->rx_msg_status | rstat);
+}
+
+static int nlm_cu2_call(struct notifier_block *nfb, unsigned long action,
+ void *data)
+{
+ unsigned long flags;
+ unsigned int status;
+
+ switch (action) {
+ case CU2_EXCEPTION:
+ if (!capable(CAP_SYS_ADMIN) || !capable(CAP_SYS_RAWIO))
+ break;
+ local_irq_save(flags);
+ KSTK_STATUS(current) |= ST0_CU2;
+ status = read_c0_status();
+ write_c0_status(status | ST0_CU2);
+ nlm_cop2_restore(&(current->thread.cp2));
+ write_c0_status(status & ~ST0_CU2);
+ local_irq_restore(flags);
+ pr_info("COP2 access enabled for pid %d (%s)\n",
+ current->pid, current->comm);
+ return NOTIFY_BAD; /* Don't call default notifier */
+ }
+
+ return NOTIFY_OK; /* Let default notifier send signals */
+}
+
+static int __init nlm_cu2_setup(void)
+{
+ return cu2_notifier(nlm_cu2_call, 0);
+}
+early_initcall(nlm_cu2_setup);
--- /dev/null
+/*
+ * Copyright 2003-2013 Broadcom Corporation.
+ * All Rights Reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/kernel.h>
+#include <linux/bootmem.h>
+
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+#include <linux/of_device.h>
+
+extern u32 __dtb_xlp_evp_begin[], __dtb_xlp_svp_begin[], __dtb_start[];
+
+void __init *xlp_dt_init(void *fdtp)
+{
+ if (!fdtp) {
+ switch (current_cpu_data.processor_id & 0xff00) {
+#ifdef CONFIG_DT_XLP_SVP
+ case PRID_IMP_NETLOGIC_XLP3XX:
+ fdtp = __dtb_xlp_svp_begin;
+ break;
+#endif
+#ifdef CONFIG_DT_XLP_EVP
+ case PRID_IMP_NETLOGIC_XLP8XX:
+ fdtp = __dtb_xlp_evp_begin;
+ break;
+#endif
+ default:
+ /* Pick a built-in if any, and hope for the best */
+ fdtp = __dtb_start;
+ break;
+ }
+ }
+ initial_boot_params = fdtp;
+ return fdtp;
+}
+
+void __init device_tree_init(void)
+{
+ unsigned long base, size;
+
+ if (!initial_boot_params)
+ return;
+
+ base = virt_to_phys((void *)initial_boot_params);
+ size = be32_to_cpu(initial_boot_params->totalsize);
+
+ /* Before we do anything, lets reserve the dt blob */
+ reserve_bootmem(base, size, BOOTMEM_DEFAULT);
+
+ unflatten_device_tree();
+
+ /* free the space reserved for the dt blob */
+ free_bootmem(base, size);
+}
+
+static struct of_device_id __initdata xlp_ids[] = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+int __init xlp8xx_ds_publish_devices(void)
+{
+ if (!of_have_populated_dt())
+ return 0;
+ return of_platform_bus_probe(NULL, xlp_ids, NULL);
+}
+
+device_initcall(xlp8xx_ds_publish_devices);
*/
#include <linux/kernel.h>
-#include <linux/serial_8250.h>
-#include <linux/pm.h>
-#include <linux/bootmem.h>
+#include <linux/of_fdt.h>
#include <asm/idle.h>
#include <asm/reboot.h>
#include <asm/time.h>
#include <asm/bootinfo.h>
-#include <linux/of_fdt.h>
-#include <linux/of_platform.h>
-#include <linux/of_device.h>
-
#include <asm/netlogic/haldefs.h>
#include <asm/netlogic/common.h>
struct nlm_soc_info nlm_nodes[NLM_NR_NODES];
cpumask_t nlm_cpumask = CPU_MASK_CPU0;
unsigned int nlm_threads_per_core;
-extern u32 __dtb_xlp_evp_begin[], __dtb_xlp_svp_begin[], __dtb_start[];
static void nlm_linux_exit(void)
{
cpu_wait();
}
-void __init plat_mem_setup(void)
+static void nlm_fixup_mem(void)
{
- void *fdtp;
+ const int pref_backup = 512;
+ int i;
+
+ for (i = 0; i < boot_mem_map.nr_map; i++) {
+ if (boot_mem_map.map[i].type != BOOT_MEM_RAM)
+ continue;
+ boot_mem_map.map[i].size -= pref_backup;
+ }
+}
+void __init plat_mem_setup(void)
+{
panic_timeout = 5;
_machine_restart = (void (*)(char *))nlm_linux_exit;
_machine_halt = nlm_linux_exit;
pm_power_off = nlm_linux_exit;
- /*
- * If no FDT pointer is passed in, use the built-in FDT.
- * device_tree_init() does not handle CKSEG0 pointers in
- * 64-bit, so convert pointer.
- */
- fdtp = (void *)(long)fw_arg0;
- if (!fdtp) {
- switch (current_cpu_data.processor_id & 0xff00) {
-#ifdef CONFIG_DT_XLP_SVP
- case PRID_IMP_NETLOGIC_XLP3XX:
- fdtp = __dtb_xlp_svp_begin;
- break;
-#endif
-#ifdef CONFIG_DT_XLP_EVP
- case PRID_IMP_NETLOGIC_XLP8XX:
- fdtp = __dtb_xlp_evp_begin;
- break;
-#endif
- default:
- /* Pick a built-in if any, and hope for the best */
- fdtp = __dtb_start;
- break;
- }
- }
- fdtp = phys_to_virt(__pa(fdtp));
- early_init_devtree(fdtp);
+ /* memory and bootargs from DT */
+ early_init_devtree(initial_boot_params);
+ nlm_fixup_mem();
}
const char *get_system_type(void)
void __init prom_init(void)
{
+ void *reset_vec;
+
nlm_io_base = CKSEG1ADDR(XLP_DEFAULT_IO_BASE);
+ nlm_init_boot_cpu();
xlp_mmu_init();
nlm_node_init(0);
+ xlp_dt_init((void *)(long)fw_arg0);
+
+ /* Update reset entry point with CPU init code */
+ reset_vec = (void *)CKSEG1ADDR(RESET_VEC_PHYS);
+ memset(reset_vec, 0, RESET_VEC_SIZE);
+ memcpy(reset_vec, (void *)nlm_reset_entry,
+ (nlm_reset_entry_end - nlm_reset_entry));
#ifdef CONFIG_SMP
cpumask_setall(&nlm_cpumask);
register_smp_ops(&nlm_smp_ops);
#endif
}
-
-void __init device_tree_init(void)
-{
- unsigned long base, size;
-
- if (!initial_boot_params)
- return;
-
- base = virt_to_phys((void *)initial_boot_params);
- size = be32_to_cpu(initial_boot_params->totalsize);
-
- /* Before we do anything, lets reserve the dt blob */
- reserve_bootmem(base, size, BOOTMEM_DEFAULT);
-
- unflatten_device_tree();
-
- /* free the space reserved for the dt blob */
- free_bootmem(base, size);
-}
-
-static struct of_device_id __initdata xlp_ids[] = {
- { .compatible = "simple-bus", },
- {},
-};
-
-int __init xlp8xx_ds_publish_devices(void)
-{
- if (!of_have_populated_dt())
- return 0;
- return of_platform_bus_probe(NULL, xlp_ids, NULL);
-}
-
-device_initcall(xlp8xx_ds_publish_devices);
return count != 0;
}
+static int wait_for_cpus(int cpu, int bootcpu)
+{
+ volatile uint32_t *cpu_ready = nlm_get_boot_data(BOOT_CPU_READY);
+ int i, count, notready;
+
+ count = 0x20000000;
+ do {
+ notready = nlm_threads_per_core;
+ for (i = 0; i < nlm_threads_per_core; i++)
+ if (cpu_ready[cpu + i] || cpu == bootcpu)
+ --notready;
+ } while (notready != 0 && --count > 0);
+
+ return count != 0;
+}
+
static void xlp_enable_secondary_cores(const cpumask_t *wakeup_mask)
{
struct nlm_soc_info *nodep;
uint64_t syspcibase;
uint32_t syscoremask;
- int core, n, cpu, count, val;
+ int core, n, cpu;
for (n = 0; n < NLM_NR_NODES; n++) {
syspcibase = nlm_get_sys_pcibase(n);
/* core is up */
nodep->coremask |= 1u << core;
- /* spin until the first hw thread sets its ready */
- count = 0x20000000;
- do {
- val = *(volatile int *)&nlm_cpu_ready[cpu];
- } while (val == 0 && --count > 0);
+ /* spin until the hw threads sets their ready */
+ wait_for_cpus(cpu, 0);
}
}
}
* first wakeup core 0 threads
*/
xlp_boot_core0_siblings();
+ wait_for_cpus(0, 0);
/* now get other cores out of reset */
xlp_enable_secondary_cores(&nlm_cpumask);
struct nlm_fmn_msg msg;
uint32_t mflags, bkt_status;
- mflags = nlm_cop2_enable();
+ mflags = nlm_cop2_enable_irqsave();
/* Disable message ring interrupt */
nlm_fmn_setup_intr(irq, 0);
while (1) {
/* 8 bkts per core, [24:31] each bit represents one bucket
* Bit is Zero if bucket is not empty */
- bkt_status = (nlm_read_c2_status() >> 24) & 0xff;
+ bkt_status = (nlm_read_c2_status0() >> 24) & 0xff;
if (bkt_status == 0xff)
break;
for (bucket = 0; bucket < 8; bucket++) {
pr_warn("No msgring handler for stnid %d\n",
src_stnid);
else {
- nlm_cop2_restore(mflags);
+ nlm_cop2_disable_irqrestore(mflags);
hndlr->action(bucket, src_stnid, size, code,
&msg, hndlr->arg);
- mflags = nlm_cop2_enable();
+ mflags = nlm_cop2_enable_irqsave();
}
}
};
/* Enable message ring intr, to any thread in core */
nlm_fmn_setup_intr(irq, (1 << nlm_threads_per_core) - 1);
- nlm_cop2_restore(mflags);
+ nlm_cop2_disable_irqrestore(mflags);
return IRQ_HANDLED;
}
bucket_sizes = xlr_board_fmn_config.bucket_size;
cpu_fmn_info = &xlr_board_fmn_config.cpu[id];
- flags = nlm_cop2_enable();
+ flags = nlm_cop2_enable_irqsave();
/* Setup bucket sizes for the core. */
nlm_write_c2_bucksize(0, bucket_sizes[id * 8 + 0]);
/* enable FMN interrupts on this CPU */
nlm_fmn_setup_intr(IRQ_FMN, (1 << nlm_threads_per_core) - 1);
- nlm_cop2_restore(flags);
+ nlm_cop2_disable_irqrestore(flags);
}
/* setup irq only once */
setup_irq(IRQ_FMN, &fmn_irqaction);
- flags = nlm_cop2_enable();
+ flags = nlm_cop2_enable_irqsave();
nlm_fmn_setup_intr(IRQ_FMN, (1 << nlm_threads_per_core) - 1);
- nlm_cop2_restore(flags);
+ nlm_cop2_disable_irqrestore(flags);
}
{
int *argv, *envp; /* passed as 32 bit ptrs */
struct psb_info *prom_infop;
+ void *reset_vec;
#ifdef CONFIG_SMP
int i;
#endif
nlm_prom_info = *prom_infop;
nlm_init_node();
+ /* Update reset entry point with CPU init code */
+ reset_vec = (void *)CKSEG1ADDR(RESET_VEC_PHYS);
+ memset(reset_vec, 0, RESET_VEC_SIZE);
+ memcpy(reset_vec, (void *)nlm_reset_entry,
+ (nlm_reset_entry_end - nlm_reset_entry));
+
nlm_early_serial_setup();
build_arcs_cmdline(argv);
prom_add_memory();
{
struct nlm_soc_info *nodep;
unsigned int i, j, boot_cpu;
+ volatile u32 *cpu_ready = nlm_get_boot_data(BOOT_CPU_READY);
/*
* In case of RMI boot, hit with NMI to get the cores
nodep->coremask = 1;
for (i = 1; i < NLM_CORES_PER_NODE; i++) {
for (j = 1000000; j > 0; j--) {
- if (nlm_cpu_ready[i * NLM_THREADS_PER_CORE])
+ if (cpu_ready[i * NLM_THREADS_PER_CORE])
break;
udelay(10);
}
obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o
obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-loongson2.o
obj-$(CONFIG_LEMOTE_MACH2F) += fixup-lemote2f.o ops-loongson2.o
-obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o
+obj-$(CONFIG_MIPS_MALTA) += fixup-malta.o pci-malta.o
obj-$(CONFIG_PMC_MSP7120_GW) += fixup-pmcmsp.o ops-pmcmsp.o
obj-$(CONFIG_PMC_MSP7120_EVAL) += fixup-pmcmsp.o ops-pmcmsp.o
obj-$(CONFIG_PMC_MSP7120_FPGA) += fixup-pmcmsp.o ops-pmcmsp.o
obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup-rbtx4938.o
obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
-obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
obj-$(CONFIG_MIKROTIK_RB532) += pci-rc32434.o ops-rc32434.o fixup-rc32434.o
-obj-$(CONFIG_CPU_CAVIUM_OCTEON) += pci-octeon.o pcie-octeon.o
+obj-$(CONFIG_CAVIUM_OCTEON_SOC) += pci-octeon.o pcie-octeon.o
obj-$(CONFIG_CPU_XLR) += pci-xlr.o
obj-$(CONFIG_CPU_XLP) += pci-xlp.o
ifdef CONFIG_PCI_MSI
-obj-$(CONFIG_CPU_CAVIUM_OCTEON) += msi-octeon.o
+obj-$(CONFIG_CAVIUM_OCTEON_SOC) += msi-octeon.o
endif
+++ /dev/null
-/*
- * fixup-wrppmc.c: PPMC board specific PCI fixup
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2006, Wind River Inc. Rongkai.zhan (rongkai.zhan@windriver.com)
- */
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <asm/gt64120.h>
-
-/* PCI interrupt pins */
-#define PCI_INTA 1
-#define PCI_INTB 2
-#define PCI_INTC 3
-#define PCI_INTD 4
-
-#define PCI_SLOT_MAXNR 32 /* Each PCI bus has 32 physical slots */
-
-static char pci_irq_tab[PCI_SLOT_MAXNR][5] __initdata = {
- /* 0 INTA INTB INTC INTD */
- [0] = {0, 0, 0, 0, 0}, /* Slot 0: GT64120 PCI bridge */
- [6] = {0, WRPPMC_PCI_INTA_IRQ, 0, 0, 0},
-};
-
-int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- return pci_irq_tab[slot][pin];
-}
-
-/* Do platform specific device initialization at pci_enable_device() time */
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
- return 0;
-}
/* setup PCI to local bus access, used by PCI device to target
* local RAM while bus mastering */
bcm63xx_int_cfg_writel(0, PCI_BASE_ADDRESS_3);
- if (BCMCPU_IS_6358() || BCMCPU_IS_6368())
+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368())
val = MPI_SP0_REMAP_ENABLE_MASK;
else
val = 0;
case BCM6328_CPU_ID:
case BCM6362_CPU_ID:
return bcm63xx_register_pcie();
+ case BCM3368_CPU_ID:
case BCM6348_CPU_ID:
case BCM6358_CPU_ID:
case BCM6368_CPU_ID:
pci_disable_swapping(d);
}
+#ifdef CONFIG_NUMA
int pcibus_to_node(struct pci_bus *bus)
{
struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
return bc->nasid;
}
EXPORT_SYMBOL(pcibus_to_node);
+#endif /* CONFIG_NUMA */
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
pci_fixup_ioc3);
--- /dev/null
+/*
+ * Copyright (C) 1999, 2000, 2004, 2005 MIPS Technologies, Inc.
+ * All rights reserved.
+ * Authors: Carsten Langgaard <carstenl@mips.com>
+ * Maciej W. Rozycki <macro@mips.com>
+ *
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * MIPS boards specific PCI support.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/gt64120.h>
+#include <asm/gcmpregs.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/bonito64.h>
+#include <asm/mips-boards/msc01_pci.h>
+
+static struct resource bonito64_mem_resource = {
+ .name = "Bonito PCI MEM",
+ .flags = IORESOURCE_MEM,
+};
+
+static struct resource bonito64_io_resource = {
+ .name = "Bonito PCI I/O",
+ .start = 0x00000000UL,
+ .end = 0x000fffffUL,
+ .flags = IORESOURCE_IO,
+};
+
+static struct resource gt64120_mem_resource = {
+ .name = "GT-64120 PCI MEM",
+ .flags = IORESOURCE_MEM,
+};
+
+static struct resource gt64120_io_resource = {
+ .name = "GT-64120 PCI I/O",
+ .flags = IORESOURCE_IO,
+};
+
+static struct resource msc_mem_resource = {
+ .name = "MSC PCI MEM",
+ .flags = IORESOURCE_MEM,
+};
+
+static struct resource msc_io_resource = {
+ .name = "MSC PCI I/O",
+ .flags = IORESOURCE_IO,
+};
+
+extern struct pci_ops bonito64_pci_ops;
+extern struct pci_ops gt64xxx_pci0_ops;
+extern struct pci_ops msc_pci_ops;
+
+static struct pci_controller bonito64_controller = {
+ .pci_ops = &bonito64_pci_ops,
+ .io_resource = &bonito64_io_resource,
+ .mem_resource = &bonito64_mem_resource,
+ .io_offset = 0x00000000UL,
+};
+
+static struct pci_controller gt64120_controller = {
+ .pci_ops = >64xxx_pci0_ops,
+ .io_resource = >64120_io_resource,
+ .mem_resource = >64120_mem_resource,
+};
+
+static struct pci_controller msc_controller = {
+ .pci_ops = &msc_pci_ops,
+ .io_resource = &msc_io_resource,
+ .mem_resource = &msc_mem_resource,
+};
+
+void __init mips_pcibios_init(void)
+{
+ struct pci_controller *controller;
+ resource_size_t start, end, map, start1, end1, map1, map2, map3, mask;
+
+ switch (mips_revision_sconid) {
+ case MIPS_REVISION_SCON_GT64120:
+ /*
+ * Due to a bug in the Galileo system controller, we need
+ * to setup the PCI BAR for the Galileo internal registers.
+ * This should be done in the bios/bootprom and will be
+ * fixed in a later revision of YAMON (the MIPS boards
+ * boot prom).
+ */
+ GT_WRITE(GT_PCI0_CFGADDR_OFS,
+ (0 << GT_PCI0_CFGADDR_BUSNUM_SHF) | /* Local bus */
+ (0 << GT_PCI0_CFGADDR_DEVNUM_SHF) | /* GT64120 dev */
+ (0 << GT_PCI0_CFGADDR_FUNCTNUM_SHF) | /* Function 0*/
+ ((0x20/4) << GT_PCI0_CFGADDR_REGNUM_SHF) | /* BAR 4*/
+ GT_PCI0_CFGADDR_CONFIGEN_BIT);
+
+ /* Perform the write */
+ GT_WRITE(GT_PCI0_CFGDATA_OFS, CPHYSADDR(MIPS_GT_BASE));
+
+ /* Set up resource ranges from the controller's registers. */
+ start = GT_READ(GT_PCI0M0LD_OFS);
+ end = GT_READ(GT_PCI0M0HD_OFS);
+ map = GT_READ(GT_PCI0M0REMAP_OFS);
+ end = (end & GT_PCI_HD_MSK) | (start & ~GT_PCI_HD_MSK);
+ start1 = GT_READ(GT_PCI0M1LD_OFS);
+ end1 = GT_READ(GT_PCI0M1HD_OFS);
+ map1 = GT_READ(GT_PCI0M1REMAP_OFS);
+ end1 = (end1 & GT_PCI_HD_MSK) | (start1 & ~GT_PCI_HD_MSK);
+ /* Cannot support multiple windows, use the wider. */
+ if (end1 - start1 > end - start) {
+ start = start1;
+ end = end1;
+ map = map1;
+ }
+ mask = ~(start ^ end);
+ /* We don't support remapping with a discontiguous mask. */
+ BUG_ON((start & GT_PCI_HD_MSK) != (map & GT_PCI_HD_MSK) &&
+ mask != ~((mask & -mask) - 1));
+ gt64120_mem_resource.start = start;
+ gt64120_mem_resource.end = end;
+ gt64120_controller.mem_offset = (start & mask) - (map & mask);
+ /* Addresses are 36-bit, so do shifts in the destinations. */
+ gt64120_mem_resource.start <<= GT_PCI_DCRM_SHF;
+ gt64120_mem_resource.end <<= GT_PCI_DCRM_SHF;
+ gt64120_mem_resource.end |= (1 << GT_PCI_DCRM_SHF) - 1;
+ gt64120_controller.mem_offset <<= GT_PCI_DCRM_SHF;
+
+ start = GT_READ(GT_PCI0IOLD_OFS);
+ end = GT_READ(GT_PCI0IOHD_OFS);
+ map = GT_READ(GT_PCI0IOREMAP_OFS);
+ end = (end & GT_PCI_HD_MSK) | (start & ~GT_PCI_HD_MSK);
+ mask = ~(start ^ end);
+ /* We don't support remapping with a discontiguous mask. */
+ BUG_ON((start & GT_PCI_HD_MSK) != (map & GT_PCI_HD_MSK) &&
+ mask != ~((mask & -mask) - 1));
+ gt64120_io_resource.start = map & mask;
+ gt64120_io_resource.end = (map & mask) | ~mask;
+ gt64120_controller.io_offset = 0;
+ /* Addresses are 36-bit, so do shifts in the destinations. */
+ gt64120_io_resource.start <<= GT_PCI_DCRM_SHF;
+ gt64120_io_resource.end <<= GT_PCI_DCRM_SHF;
+ gt64120_io_resource.end |= (1 << GT_PCI_DCRM_SHF) - 1;
+
+ controller = >64120_controller;
+ break;
+
+ case MIPS_REVISION_SCON_BONITO:
+ /* Set up resource ranges from the controller's registers. */
+ map = BONITO_PCIMAP;
+ map1 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO0) >>
+ BONITO_PCIMAP_PCIMAP_LO0_SHIFT;
+ map2 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO1) >>
+ BONITO_PCIMAP_PCIMAP_LO1_SHIFT;
+ map3 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO2) >>
+ BONITO_PCIMAP_PCIMAP_LO2_SHIFT;
+ /* Combine as many adjacent windows as possible. */
+ map = map1;
+ start = BONITO_PCILO0_BASE;
+ end = 1;
+ if (map3 == map2 + 1) {
+ map = map2;
+ start = BONITO_PCILO1_BASE;
+ end++;
+ }
+ if (map2 == map1 + 1) {
+ map = map1;
+ start = BONITO_PCILO0_BASE;
+ end++;
+ }
+ bonito64_mem_resource.start = start;
+ bonito64_mem_resource.end = start +
+ BONITO_PCIMAP_WINBASE(end) - 1;
+ bonito64_controller.mem_offset = start -
+ BONITO_PCIMAP_WINBASE(map);
+
+ controller = &bonito64_controller;
+ break;
+
+ case MIPS_REVISION_SCON_SOCIT:
+ case MIPS_REVISION_SCON_ROCIT:
+ case MIPS_REVISION_SCON_SOCITSC:
+ case MIPS_REVISION_SCON_SOCITSCP:
+ /* Set up resource ranges from the controller's registers. */
+ MSC_READ(MSC01_PCI_SC2PMBASL, start);
+ MSC_READ(MSC01_PCI_SC2PMMSKL, mask);
+ MSC_READ(MSC01_PCI_SC2PMMAPL, map);
+ msc_mem_resource.start = start & mask;
+ msc_mem_resource.end = (start & mask) | ~mask;
+ msc_controller.mem_offset = (start & mask) - (map & mask);
+#ifdef CONFIG_MIPS_CMP
+ if (gcmp_niocu())
+ gcmp_setregion(0, start, mask,
+ GCMP_GCB_GCMPB_CMDEFTGT_IOCU1);
+#endif
+ MSC_READ(MSC01_PCI_SC2PIOBASL, start);
+ MSC_READ(MSC01_PCI_SC2PIOMSKL, mask);
+ MSC_READ(MSC01_PCI_SC2PIOMAPL, map);
+ msc_io_resource.start = map & mask;
+ msc_io_resource.end = (map & mask) | ~mask;
+ msc_controller.io_offset = 0;
+ ioport_resource.end = ~mask;
+#ifdef CONFIG_MIPS_CMP
+ if (gcmp_niocu())
+ gcmp_setregion(1, start, mask,
+ GCMP_GCB_GCMPB_CMDEFTGT_IOCU1);
+#endif
+ /* If ranges overlap I/O takes precedence. */
+ start = start & mask;
+ end = start | ~mask;
+ if ((start >= msc_mem_resource.start &&
+ start <= msc_mem_resource.end) ||
+ (end >= msc_mem_resource.start &&
+ end <= msc_mem_resource.end)) {
+ /* Use the larger space. */
+ start = max(start, msc_mem_resource.start);
+ end = min(end, msc_mem_resource.end);
+ if (start - msc_mem_resource.start >=
+ msc_mem_resource.end - end)
+ msc_mem_resource.end = start - 1;
+ else
+ msc_mem_resource.start = end + 1;
+ }
+
+ controller = &msc_controller;
+ break;
+ default:
+ return;
+ }
+
+ /* Change start address to avoid conflicts with ACPI and SMB devices */
+ if (controller->io_resource->start < 0x00002000UL)
+ controller->io_resource->start = 0x00002000UL;
+
+ iomem_resource.end &= 0xfffffffffULL; /* 64 GB */
+ ioport_resource.end = controller->io_resource->end;
+
+ controller->io_map_base = mips_io_port_base;
+
+ register_pci_controller(controller);
+}
#
obj-y += msp_prom.o msp_setup.o msp_irq.o \
msp_time.o msp_serial.o msp_elb.o
-obj-$(CONFIG_HAVE_GPIO_LIB) += gpio.o gpio_extended.o
obj-$(CONFIG_PMC_MSP7120_GW) += msp_hwbutton.o
obj-$(CONFIG_IRQ_MSP_SLP) += msp_irq_slp.o
obj-$(CONFIG_IRQ_MSP_CIC) += msp_irq_cic.o msp_irq_per.o
+++ /dev/null
-/*
- * Generic PMC MSP71xx GPIO handling. These base gpio are controlled by two
- * types of registers. The data register sets the output level when in output
- * mode and when in input mode will contain the value at the input. The config
- * register sets the various modes for each gpio.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * @author Patrick Glass <patrickglass@gmail.com>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/spinlock.h>
-#include <linux/io.h>
-
-#define MSP71XX_CFG_OFFSET(gpio) (4 * (gpio))
-#define CONF_MASK 0x0F
-#define MSP71XX_GPIO_INPUT 0x01
-#define MSP71XX_GPIO_OUTPUT 0x08
-
-#define MSP71XX_GPIO_BASE 0x0B8400000L
-
-#define to_msp71xx_gpio_chip(c) container_of(c, struct msp71xx_gpio_chip, chip)
-
-static spinlock_t gpio_lock;
-
-/*
- * struct msp71xx_gpio_chip - container for gpio chip and registers
- * @chip: chip structure for the specified gpio bank
- * @data_reg: register for reading and writing the gpio pin value
- * @config_reg: register to set the mode for the gpio pin bank
- * @out_drive_reg: register to set the output drive mode for the gpio pin bank
- */
-struct msp71xx_gpio_chip {
- struct gpio_chip chip;
- void __iomem *data_reg;
- void __iomem *config_reg;
- void __iomem *out_drive_reg;
-};
-
-/*
- * msp71xx_gpio_get() - return the chip's gpio value
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose value will be returned
- *
- * It will return 0 if gpio value is low and other if high.
- */
-static int msp71xx_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
- struct msp71xx_gpio_chip *msp_chip = to_msp71xx_gpio_chip(chip);
-
- return __raw_readl(msp_chip->data_reg) & (1 << offset);
-}
-
-/*
- * msp71xx_gpio_set() - set the output value for the gpio
- * @chip: chip structure who controls the specified gpio
- * @offset: gpio whose value will be assigned
- * @value: logic level to assign to the gpio initially
- *
- * This will set the gpio bit specified to the desired value. It will set the
- * gpio pin low if value is 0 otherwise it will be high.
- */
-static void msp71xx_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- struct msp71xx_gpio_chip *msp_chip = to_msp71xx_gpio_chip(chip);
- unsigned long flags;
- u32 data;
-
- spin_lock_irqsave(&gpio_lock, flags);
-
- data = __raw_readl(msp_chip->data_reg);
- if (value)
- data |= (1 << offset);
- else
- data &= ~(1 << offset);
- __raw_writel(data, msp_chip->data_reg);
-
- spin_unlock_irqrestore(&gpio_lock, flags);
-}
-
-/*
- * msp71xx_set_gpio_mode() - declare the mode for a gpio
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose value will be assigned
- * @mode: desired configuration for the gpio (see datasheet)
- *
- * It will set the gpio pin config to the @mode value passed in.
- */
-static int msp71xx_set_gpio_mode(struct gpio_chip *chip,
- unsigned offset, int mode)
-{
- struct msp71xx_gpio_chip *msp_chip = to_msp71xx_gpio_chip(chip);
- const unsigned bit_offset = MSP71XX_CFG_OFFSET(offset);
- unsigned long flags;
- u32 cfg;
-
- spin_lock_irqsave(&gpio_lock, flags);
-
- cfg = __raw_readl(msp_chip->config_reg);
- cfg &= ~(CONF_MASK << bit_offset);
- cfg |= (mode << bit_offset);
- __raw_writel(cfg, msp_chip->config_reg);
-
- spin_unlock_irqrestore(&gpio_lock, flags);
-
- return 0;
-}
-
-/*
- * msp71xx_direction_output() - declare the direction mode for a gpio
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose value will be assigned
- * @value: logic level to assign to the gpio initially
- *
- * This call will set the mode for the @gpio to output. It will set the
- * gpio pin low if value is 0 otherwise it will be high.
- */
-static int msp71xx_direction_output(struct gpio_chip *chip,
- unsigned offset, int value)
-{
- msp71xx_gpio_set(chip, offset, value);
-
- return msp71xx_set_gpio_mode(chip, offset, MSP71XX_GPIO_OUTPUT);
-}
-
-/*
- * msp71xx_direction_input() - declare the direction mode for a gpio
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose to which the value will be assigned
- *
- * This call will set the mode for the @gpio to input.
- */
-static int msp71xx_direction_input(struct gpio_chip *chip, unsigned offset)
-{
- return msp71xx_set_gpio_mode(chip, offset, MSP71XX_GPIO_INPUT);
-}
-
-/*
- * msp71xx_set_output_drive() - declare the output drive for the gpio line
- * @gpio: gpio pin whose output drive you wish to modify
- * @value: zero for active drain 1 for open drain drive
- *
- * This call will set the output drive mode for the @gpio to output.
- */
-int msp71xx_set_output_drive(unsigned gpio, int value)
-{
- unsigned long flags;
- u32 data;
-
- if (gpio > 15 || gpio < 0)
- return -EINVAL;
-
- spin_lock_irqsave(&gpio_lock, flags);
-
- data = __raw_readl((void __iomem *)(MSP71XX_GPIO_BASE + 0x190));
- if (value)
- data |= (1 << gpio);
- else
- data &= ~(1 << gpio);
- __raw_writel(data, (void __iomem *)(MSP71XX_GPIO_BASE + 0x190));
-
- spin_unlock_irqrestore(&gpio_lock, flags);
-
- return 0;
-}
-EXPORT_SYMBOL(msp71xx_set_output_drive);
-
-#define MSP71XX_GPIO_BANK(name, dr, cr, base_gpio, num_gpio) \
-{ \
- .chip = { \
- .label = name, \
- .direction_input = msp71xx_direction_input, \
- .direction_output = msp71xx_direction_output, \
- .get = msp71xx_gpio_get, \
- .set = msp71xx_gpio_set, \
- .base = base_gpio, \
- .ngpio = num_gpio \
- }, \
- .data_reg = (void __iomem *)(MSP71XX_GPIO_BASE + dr), \
- .config_reg = (void __iomem *)(MSP71XX_GPIO_BASE + cr), \
- .out_drive_reg = (void __iomem *)(MSP71XX_GPIO_BASE + 0x190), \
-}
-
-/*
- * struct msp71xx_gpio_banks[] - container array of gpio banks
- * @chip: chip structure for the specified gpio bank
- * @data_reg: register for reading and writing the gpio pin value
- * @config_reg: register to set the mode for the gpio pin bank
- *
- * This array structure defines the gpio banks for the PMC MIPS Processor.
- * We specify the bank name, the data register, the config register, base
- * starting gpio number, and the number of gpios exposed by the bank.
- */
-static struct msp71xx_gpio_chip msp71xx_gpio_banks[] = {
-
- MSP71XX_GPIO_BANK("GPIO_1_0", 0x170, 0x180, 0, 2),
- MSP71XX_GPIO_BANK("GPIO_5_2", 0x174, 0x184, 2, 4),
- MSP71XX_GPIO_BANK("GPIO_9_6", 0x178, 0x188, 6, 4),
- MSP71XX_GPIO_BANK("GPIO_15_10", 0x17C, 0x18C, 10, 6),
-};
-
-void __init msp71xx_init_gpio(void)
-{
- int i;
-
- spin_lock_init(&gpio_lock);
-
- for (i = 0; i < ARRAY_SIZE(msp71xx_gpio_banks); i++)
- gpiochip_add(&msp71xx_gpio_banks[i].chip);
-}
+++ /dev/null
-/*
- * Generic PMC MSP71xx EXTENDED (EXD) GPIO handling. The extended gpio is
- * a set of hardware registers that have no need for explicit locking as
- * it is handled by unique method of writing individual set/clr bits.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * @author Patrick Glass <patrickglass@gmail.com>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/io.h>
-
-#define MSP71XX_DATA_OFFSET(gpio) (2 * (gpio))
-#define MSP71XX_READ_OFFSET(gpio) (MSP71XX_DATA_OFFSET(gpio) + 1)
-#define MSP71XX_CFG_OUT_OFFSET(gpio) (MSP71XX_DATA_OFFSET(gpio) + 16)
-#define MSP71XX_CFG_IN_OFFSET(gpio) (MSP71XX_CFG_OUT_OFFSET(gpio) + 1)
-
-#define MSP71XX_EXD_GPIO_BASE 0x0BC000000L
-
-#define to_msp71xx_exd_gpio_chip(c) \
- container_of(c, struct msp71xx_exd_gpio_chip, chip)
-
-/*
- * struct msp71xx_exd_gpio_chip - container for gpio chip and registers
- * @chip: chip structure for the specified gpio bank
- * @reg: register for control and data of gpio pin
- */
-struct msp71xx_exd_gpio_chip {
- struct gpio_chip chip;
- void __iomem *reg;
-};
-
-/*
- * msp71xx_exd_gpio_get() - return the chip's gpio value
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose value will be returned
- *
- * It will return 0 if gpio value is low and other if high.
- */
-static int msp71xx_exd_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
- struct msp71xx_exd_gpio_chip *msp71xx_chip =
- to_msp71xx_exd_gpio_chip(chip);
- const unsigned bit = MSP71XX_READ_OFFSET(offset);
-
- return __raw_readl(msp71xx_chip->reg) & (1 << bit);
-}
-
-/*
- * msp71xx_exd_gpio_set() - set the output value for the gpio
- * @chip: chip structure who controls the specified gpio
- * @offset: gpio whose value will be assigned
- * @value: logic level to assign to the gpio initially
- *
- * This will set the gpio bit specified to the desired value. It will set the
- * gpio pin low if value is 0 otherwise it will be high.
- */
-static void msp71xx_exd_gpio_set(struct gpio_chip *chip,
- unsigned offset, int value)
-{
- struct msp71xx_exd_gpio_chip *msp71xx_chip =
- to_msp71xx_exd_gpio_chip(chip);
- const unsigned bit = MSP71XX_DATA_OFFSET(offset);
-
- __raw_writel(1 << (bit + (value ? 1 : 0)), msp71xx_chip->reg);
-}
-
-/*
- * msp71xx_exd_direction_output() - declare the direction mode for a gpio
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose value will be assigned
- * @value: logic level to assign to the gpio initially
- *
- * This call will set the mode for the @gpio to output. It will set the
- * gpio pin low if value is 0 otherwise it will be high.
- */
-static int msp71xx_exd_direction_output(struct gpio_chip *chip,
- unsigned offset, int value)
-{
- struct msp71xx_exd_gpio_chip *msp71xx_chip =
- to_msp71xx_exd_gpio_chip(chip);
-
- msp71xx_exd_gpio_set(chip, offset, value);
- __raw_writel(1 << MSP71XX_CFG_OUT_OFFSET(offset), msp71xx_chip->reg);
- return 0;
-}
-
-/*
- * msp71xx_exd_direction_input() - declare the direction mode for a gpio
- * @chip: chip structure which controls the specified gpio
- * @offset: gpio whose to which the value will be assigned
- *
- * This call will set the mode for the @gpio to input.
- */
-static int msp71xx_exd_direction_input(struct gpio_chip *chip, unsigned offset)
-{
- struct msp71xx_exd_gpio_chip *msp71xx_chip =
- to_msp71xx_exd_gpio_chip(chip);
-
- __raw_writel(1 << MSP71XX_CFG_IN_OFFSET(offset), msp71xx_chip->reg);
- return 0;
-}
-
-#define MSP71XX_EXD_GPIO_BANK(name, exd_reg, base_gpio, num_gpio) \
-{ \
- .chip = { \
- .label = name, \
- .direction_input = msp71xx_exd_direction_input, \
- .direction_output = msp71xx_exd_direction_output, \
- .get = msp71xx_exd_gpio_get, \
- .set = msp71xx_exd_gpio_set, \
- .base = base_gpio, \
- .ngpio = num_gpio, \
- }, \
- .reg = (void __iomem *)(MSP71XX_EXD_GPIO_BASE + exd_reg), \
-}
-
-/*
- * struct msp71xx_exd_gpio_banks[] - container array of gpio banks
- * @chip: chip structure for the specified gpio bank
- * @reg: register for reading and writing the gpio pin value
- *
- * This array structure defines the extended gpio banks for the
- * PMC MIPS Processor. We specify the bank name, the data/config
- * register,the base starting gpio number, and the number of
- * gpios exposed by the bank of gpios.
- */
-static struct msp71xx_exd_gpio_chip msp71xx_exd_gpio_banks[] = {
-
- MSP71XX_EXD_GPIO_BANK("GPIO_23_16", 0x188, 16, 8),
- MSP71XX_EXD_GPIO_BANK("GPIO_27_24", 0x18C, 24, 4),
-};
-
-void __init msp71xx_init_gpio_extended(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(msp71xx_exd_gpio_banks); i++)
- gpiochip_add(&msp71xx_exd_gpio_banks[i].chip);
-}
*/
void platform_release_memory(void *ptr, int size)
{
- unsigned long addr;
- unsigned long end;
-
- addr = ((unsigned long)ptr + (PAGE_SIZE - 1)) & PAGE_MASK;
- end = ((unsigned long)ptr + size) & PAGE_MASK;
-
- for (; addr < end; addr += PAGE_SIZE) {
- ClearPageReserved(virt_to_page(__va(addr)));
- init_page_count(virt_to_page(__va(addr)));
- free_page((unsigned long)__va(addr));
- }
+ free_reserved_area((unsigned long)ptr, (unsigned long)(ptr + size),
+ -1, NULL);
}
EXPORT_SYMBOL(platform_release_memory);
if (!of_have_populated_dt())
panic("device tree not present");
- strncpy(of_ids[0].compatible, soc_info.compatible, len);
+ strlcpy(of_ids[0].compatible, soc_info.compatible, len);
strncpy(of_ids[1].compatible, "palmbus", len);
if (of_platform_populate(NULL, of_ids, NULL, NULL))
ip27-xtalk.o
obj-$(CONFIG_EARLY_PRINTK) += ip27-console.o
+obj-$(CONFIG_PCI) += ip27-irq-pci.o
obj-$(CONFIG_SMP) += ip27-smp.o
--- /dev/null
+/*
+ * ip27-irq.c: Highlevel interrupt handling for IP27 architecture.
+ *
+ * Copyright (C) 1999, 2000 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 1999 - 2001 Kanoj Sarcar
+ */
+
+#undef DEBUG
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/timex.h>
+#include <linux/smp.h>
+#include <linux/random.h>
+#include <linux/kernel.h>
+#include <linux/kernel_stat.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+
+#include <asm/bootinfo.h>
+#include <asm/io.h>
+#include <asm/mipsregs.h>
+
+#include <asm/processor.h>
+#include <asm/pci/bridge.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/hub.h>
+#include <asm/sn/intr.h>
+
+/*
+ * Linux has a controller-independent x86 interrupt architecture.
+ * every controller has a 'controller-template', that is used
+ * by the main code to do the right thing. Each driver-visible
+ * interrupt source is transparently wired to the appropriate
+ * controller. Thus drivers need not be aware of the
+ * interrupt-controller.
+ *
+ * Various interrupt controllers we handle: 8259 PIC, SMP IO-APIC,
+ * PIIX4's internal 8259 PIC and SGI's Visual Workstation Cobalt (IO-)APIC.
+ * (IO-APICs assumed to be messaging to Pentium local-APICs)
+ *
+ * the code is designed to be easily extended with new/different
+ * interrupt controllers, without having to do assembly magic.
+ */
+
+extern struct bridge_controller *irq_to_bridge[];
+extern int irq_to_slot[];
+
+/*
+ * use these macros to get the encoded nasid and widget id
+ * from the irq value
+ */
+#define IRQ_TO_BRIDGE(i) irq_to_bridge[(i)]
+#define SLOT_FROM_PCI_IRQ(i) irq_to_slot[i]
+
+static inline int alloc_level(int cpu, int irq)
+{
+ struct hub_data *hub = hub_data(cpu_to_node(cpu));
+ struct slice_data *si = cpu_data[cpu].data;
+ int level;
+
+ level = find_first_zero_bit(hub->irq_alloc_mask, LEVELS_PER_SLICE);
+ if (level >= LEVELS_PER_SLICE)
+ panic("Cpu %d flooded with devices", cpu);
+
+ __set_bit(level, hub->irq_alloc_mask);
+ si->level_to_irq[level] = irq;
+
+ return level;
+}
+
+static inline int find_level(cpuid_t *cpunum, int irq)
+{
+ int cpu, i;
+
+ for_each_online_cpu(cpu) {
+ struct slice_data *si = cpu_data[cpu].data;
+
+ for (i = BASE_PCI_IRQ; i < LEVELS_PER_SLICE; i++)
+ if (si->level_to_irq[i] == irq) {
+ *cpunum = cpu;
+
+ return i;
+ }
+ }
+
+ panic("Could not identify cpu/level for irq %d", irq);
+}
+
+static int intr_connect_level(int cpu, int bit)
+{
+ nasid_t nasid = COMPACT_TO_NASID_NODEID(cpu_to_node(cpu));
+ struct slice_data *si = cpu_data[cpu].data;
+
+ set_bit(bit, si->irq_enable_mask);
+
+ if (!cputoslice(cpu)) {
+ REMOTE_HUB_S(nasid, PI_INT_MASK0_A, si->irq_enable_mask[0]);
+ REMOTE_HUB_S(nasid, PI_INT_MASK1_A, si->irq_enable_mask[1]);
+ } else {
+ REMOTE_HUB_S(nasid, PI_INT_MASK0_B, si->irq_enable_mask[0]);
+ REMOTE_HUB_S(nasid, PI_INT_MASK1_B, si->irq_enable_mask[1]);
+ }
+
+ return 0;
+}
+
+static int intr_disconnect_level(int cpu, int bit)
+{
+ nasid_t nasid = COMPACT_TO_NASID_NODEID(cpu_to_node(cpu));
+ struct slice_data *si = cpu_data[cpu].data;
+
+ clear_bit(bit, si->irq_enable_mask);
+
+ if (!cputoslice(cpu)) {
+ REMOTE_HUB_S(nasid, PI_INT_MASK0_A, si->irq_enable_mask[0]);
+ REMOTE_HUB_S(nasid, PI_INT_MASK1_A, si->irq_enable_mask[1]);
+ } else {
+ REMOTE_HUB_S(nasid, PI_INT_MASK0_B, si->irq_enable_mask[0]);
+ REMOTE_HUB_S(nasid, PI_INT_MASK1_B, si->irq_enable_mask[1]);
+ }
+
+ return 0;
+}
+
+/* Startup one of the (PCI ...) IRQs routes over a bridge. */
+static unsigned int startup_bridge_irq(struct irq_data *d)
+{
+ struct bridge_controller *bc;
+ bridgereg_t device;
+ bridge_t *bridge;
+ int pin, swlevel;
+ cpuid_t cpu;
+
+ pin = SLOT_FROM_PCI_IRQ(d->irq);
+ bc = IRQ_TO_BRIDGE(d->irq);
+ bridge = bc->base;
+
+ pr_debug("bridge_startup(): irq= 0x%x pin=%d\n", d->irq, pin);
+ /*
+ * "map" irq to a swlevel greater than 6 since the first 6 bits
+ * of INT_PEND0 are taken
+ */
+ swlevel = find_level(&cpu, d->irq);
+ bridge->b_int_addr[pin].addr = (0x20000 | swlevel | (bc->nasid << 8));
+ bridge->b_int_enable |= (1 << pin);
+ bridge->b_int_enable |= 0x7ffffe00; /* more stuff in int_enable */
+
+ /*
+ * Enable sending of an interrupt clear packt to the hub on a high to
+ * low transition of the interrupt pin.
+ *
+ * IRIX sets additional bits in the address which are documented as
+ * reserved in the bridge docs.
+ */
+ bridge->b_int_mode |= (1UL << pin);
+
+ /*
+ * We assume the bridge to have a 1:1 mapping between devices
+ * (slots) and intr pins.
+ */
+ device = bridge->b_int_device;
+ device &= ~(7 << (pin*3));
+ device |= (pin << (pin*3));
+ bridge->b_int_device = device;
+
+ bridge->b_wid_tflush;
+
+ intr_connect_level(cpu, swlevel);
+
+ return 0; /* Never anything pending. */
+}
+
+/* Shutdown one of the (PCI ...) IRQs routes over a bridge. */
+static void shutdown_bridge_irq(struct irq_data *d)
+{
+ struct bridge_controller *bc = IRQ_TO_BRIDGE(d->irq);
+ bridge_t *bridge = bc->base;
+ int pin, swlevel;
+ cpuid_t cpu;
+
+ pr_debug("bridge_shutdown: irq 0x%x\n", d->irq);
+ pin = SLOT_FROM_PCI_IRQ(d->irq);
+
+ /*
+ * map irq to a swlevel greater than 6 since the first 6 bits
+ * of INT_PEND0 are taken
+ */
+ swlevel = find_level(&cpu, d->irq);
+ intr_disconnect_level(cpu, swlevel);
+
+ bridge->b_int_enable &= ~(1 << pin);
+ bridge->b_wid_tflush;
+}
+
+static inline void enable_bridge_irq(struct irq_data *d)
+{
+ cpuid_t cpu;
+ int swlevel;
+
+ swlevel = find_level(&cpu, d->irq); /* Criminal offence */
+ intr_connect_level(cpu, swlevel);
+}
+
+static inline void disable_bridge_irq(struct irq_data *d)
+{
+ cpuid_t cpu;
+ int swlevel;
+
+ swlevel = find_level(&cpu, d->irq); /* Criminal offence */
+ intr_disconnect_level(cpu, swlevel);
+}
+
+static struct irq_chip bridge_irq_type = {
+ .name = "bridge",
+ .irq_startup = startup_bridge_irq,
+ .irq_shutdown = shutdown_bridge_irq,
+ .irq_mask = disable_bridge_irq,
+ .irq_unmask = enable_bridge_irq,
+};
+
+void register_bridge_irq(unsigned int irq)
+{
+ irq_set_chip_and_handler(irq, &bridge_irq_type, handle_level_irq);
+}
+
+int request_bridge_irq(struct bridge_controller *bc)
+{
+ int irq = allocate_irqno();
+ int swlevel, cpu;
+ nasid_t nasid;
+
+ if (irq < 0)
+ return irq;
+
+ /*
+ * "map" irq to a swlevel greater than 6 since the first 6 bits
+ * of INT_PEND0 are taken
+ */
+ cpu = bc->irq_cpu;
+ swlevel = alloc_level(cpu, irq);
+ if (unlikely(swlevel < 0)) {
+ free_irqno(irq);
+
+ return -EAGAIN;
+ }
+
+ /* Make sure it's not already pending when we connect it. */
+ nasid = COMPACT_TO_NASID_NODEID(cpu_to_node(cpu));
+ REMOTE_HUB_CLR_INTR(nasid, swlevel);
+
+ intr_connect_level(cpu, swlevel);
+
+ register_bridge_irq(irq);
+
+ return irq;
+}
#include <asm/mipsregs.h>
#include <asm/processor.h>
-#include <asm/pci/bridge.h>
#include <asm/sn/addrs.h>
#include <asm/sn/agent.h>
#include <asm/sn/arch.h>
extern asmlinkage void ip27_irq(void);
-extern struct bridge_controller *irq_to_bridge[];
-extern int irq_to_slot[];
-
-/*
- * use these macros to get the encoded nasid and widget id
- * from the irq value
- */
-#define IRQ_TO_BRIDGE(i) irq_to_bridge[(i)]
-#define SLOT_FROM_PCI_IRQ(i) irq_to_slot[i]
-
-static inline int alloc_level(int cpu, int irq)
-{
- struct hub_data *hub = hub_data(cpu_to_node(cpu));
- struct slice_data *si = cpu_data[cpu].data;
- int level;
-
- level = find_first_zero_bit(hub->irq_alloc_mask, LEVELS_PER_SLICE);
- if (level >= LEVELS_PER_SLICE)
- panic("Cpu %d flooded with devices", cpu);
-
- __set_bit(level, hub->irq_alloc_mask);
- si->level_to_irq[level] = irq;
-
- return level;
-}
-
-static inline int find_level(cpuid_t *cpunum, int irq)
-{
- int cpu, i;
-
- for_each_online_cpu(cpu) {
- struct slice_data *si = cpu_data[cpu].data;
-
- for (i = BASE_PCI_IRQ; i < LEVELS_PER_SLICE; i++)
- if (si->level_to_irq[i] == irq) {
- *cpunum = cpu;
-
- return i;
- }
- }
-
- panic("Could not identify cpu/level for irq %d", irq);
-}
-
/*
* Find first bit set
*/
panic("CPU %d got a hub error interrupt", smp_processor_id());
}
-static int intr_connect_level(int cpu, int bit)
-{
- nasid_t nasid = COMPACT_TO_NASID_NODEID(cpu_to_node(cpu));
- struct slice_data *si = cpu_data[cpu].data;
-
- set_bit(bit, si->irq_enable_mask);
-
- if (!cputoslice(cpu)) {
- REMOTE_HUB_S(nasid, PI_INT_MASK0_A, si->irq_enable_mask[0]);
- REMOTE_HUB_S(nasid, PI_INT_MASK1_A, si->irq_enable_mask[1]);
- } else {
- REMOTE_HUB_S(nasid, PI_INT_MASK0_B, si->irq_enable_mask[0]);
- REMOTE_HUB_S(nasid, PI_INT_MASK1_B, si->irq_enable_mask[1]);
- }
-
- return 0;
-}
-
-static int intr_disconnect_level(int cpu, int bit)
-{
- nasid_t nasid = COMPACT_TO_NASID_NODEID(cpu_to_node(cpu));
- struct slice_data *si = cpu_data[cpu].data;
-
- clear_bit(bit, si->irq_enable_mask);
-
- if (!cputoslice(cpu)) {
- REMOTE_HUB_S(nasid, PI_INT_MASK0_A, si->irq_enable_mask[0]);
- REMOTE_HUB_S(nasid, PI_INT_MASK1_A, si->irq_enable_mask[1]);
- } else {
- REMOTE_HUB_S(nasid, PI_INT_MASK0_B, si->irq_enable_mask[0]);
- REMOTE_HUB_S(nasid, PI_INT_MASK1_B, si->irq_enable_mask[1]);
- }
-
- return 0;
-}
-
-/* Startup one of the (PCI ...) IRQs routes over a bridge. */
-static unsigned int startup_bridge_irq(struct irq_data *d)
-{
- struct bridge_controller *bc;
- bridgereg_t device;
- bridge_t *bridge;
- int pin, swlevel;
- cpuid_t cpu;
-
- pin = SLOT_FROM_PCI_IRQ(d->irq);
- bc = IRQ_TO_BRIDGE(d->irq);
- bridge = bc->base;
-
- pr_debug("bridge_startup(): irq= 0x%x pin=%d\n", d->irq, pin);
- /*
- * "map" irq to a swlevel greater than 6 since the first 6 bits
- * of INT_PEND0 are taken
- */
- swlevel = find_level(&cpu, d->irq);
- bridge->b_int_addr[pin].addr = (0x20000 | swlevel | (bc->nasid << 8));
- bridge->b_int_enable |= (1 << pin);
- bridge->b_int_enable |= 0x7ffffe00; /* more stuff in int_enable */
-
- /*
- * Enable sending of an interrupt clear packt to the hub on a high to
- * low transition of the interrupt pin.
- *
- * IRIX sets additional bits in the address which are documented as
- * reserved in the bridge docs.
- */
- bridge->b_int_mode |= (1UL << pin);
-
- /*
- * We assume the bridge to have a 1:1 mapping between devices
- * (slots) and intr pins.
- */
- device = bridge->b_int_device;
- device &= ~(7 << (pin*3));
- device |= (pin << (pin*3));
- bridge->b_int_device = device;
-
- bridge->b_wid_tflush;
-
- intr_connect_level(cpu, swlevel);
-
- return 0; /* Never anything pending. */
-}
-
-/* Shutdown one of the (PCI ...) IRQs routes over a bridge. */
-static void shutdown_bridge_irq(struct irq_data *d)
-{
- struct bridge_controller *bc = IRQ_TO_BRIDGE(d->irq);
- bridge_t *bridge = bc->base;
- int pin, swlevel;
- cpuid_t cpu;
-
- pr_debug("bridge_shutdown: irq 0x%x\n", d->irq);
- pin = SLOT_FROM_PCI_IRQ(d->irq);
-
- /*
- * map irq to a swlevel greater than 6 since the first 6 bits
- * of INT_PEND0 are taken
- */
- swlevel = find_level(&cpu, d->irq);
- intr_disconnect_level(cpu, swlevel);
-
- bridge->b_int_enable &= ~(1 << pin);
- bridge->b_wid_tflush;
-}
-
-static inline void enable_bridge_irq(struct irq_data *d)
-{
- cpuid_t cpu;
- int swlevel;
-
- swlevel = find_level(&cpu, d->irq); /* Criminal offence */
- intr_connect_level(cpu, swlevel);
-}
-
-static inline void disable_bridge_irq(struct irq_data *d)
-{
- cpuid_t cpu;
- int swlevel;
-
- swlevel = find_level(&cpu, d->irq); /* Criminal offence */
- intr_disconnect_level(cpu, swlevel);
-}
-
-static struct irq_chip bridge_irq_type = {
- .name = "bridge",
- .irq_startup = startup_bridge_irq,
- .irq_shutdown = shutdown_bridge_irq,
- .irq_mask = disable_bridge_irq,
- .irq_unmask = enable_bridge_irq,
-};
-
-void register_bridge_irq(unsigned int irq)
-{
- irq_set_chip_and_handler(irq, &bridge_irq_type, handle_level_irq);
-}
-
-int request_bridge_irq(struct bridge_controller *bc)
-{
- int irq = allocate_irqno();
- int swlevel, cpu;
- nasid_t nasid;
-
- if (irq < 0)
- return irq;
-
- /*
- * "map" irq to a swlevel greater than 6 since the first 6 bits
- * of INT_PEND0 are taken
- */
- cpu = bc->irq_cpu;
- swlevel = alloc_level(cpu, irq);
- if (unlikely(swlevel < 0)) {
- free_irqno(irq);
-
- return -EAGAIN;
- }
-
- /* Make sure it's not already pending when we connect it. */
- nasid = COMPACT_TO_NASID_NODEID(cpu_to_node(cpu));
- REMOTE_HUB_CLR_INTR(nasid, swlevel);
-
- intr_connect_level(cpu, swlevel);
-
- register_bridge_irq(irq);
-
- return irq;
-}
-
asmlinkage void plat_irq_dispatch(void)
{
unsigned long pending = read_c0_cause() & read_c0_status();
config SIBYTE_BUS_WATCHER
bool "Support for Bus Watcher statistics"
- depends on SIBYTE_SB1xxx_SOC
+ depends on SIBYTE_SB1xxx_SOC && \
+ (SIBYTE_BCM112X || SIBYTE_SB1250)
help
Handle and keep statistics on the bus error interrupts (COR_ECC,
BAD_ECC, IO_BUS).
-I$(srctree)/arch/mips/include/asm/mach-sibyte \
-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
-platform-$(CONFIG_SIBYTE_SB1250) += sibyte/
cflags-$(CONFIG_SIBYTE_SB1250) += \
-I$(srctree)/arch/mips/include/asm/mach-sibyte \
-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
# Sibyte BCM91120C (CRhine) board
# Sibyte BCM91125C (CRhone) board
# Sibyte BCM91125E (Rhone) board
-# Sibyte SWARM board
+# Sibyte BCM91250A (SWARM) board
+# Sibyte BCM91250C2 (LittleSur) board
# Sibyte BCM91x80 (BigSur) board
#
load-$(CONFIG_SIBYTE_CARMEL) := 0xffffffff80100000
load-$(CONFIG_SIBYTE_SENTOSA) := 0xffffffff80100000
load-$(CONFIG_SIBYTE_SWARM) := 0xffffffff80100000
load-$(CONFIG_SIBYTE_BIGSUR) := 0xffffffff80100000
+load-$(CONFIG_SIBYTE_LITTLESUR) := 0xffffffff80100000
obj-y := cfe.o
+obj-$(CONFIG_SIBYTE_BUS_WATCHER) += bus_watcher.o
obj-$(CONFIG_SIBYTE_CFE_CONSOLE) += cfe_console.o
obj-$(CONFIG_SIBYTE_TBPROF) += sb_tbprof.o
--- /dev/null
+/*
+ * Copyright (C) 2002,2003 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+/*
+ * The Bus Watcher monitors internal bus transactions and maintains
+ * counts of transactions with error status, logging details and
+ * causing one of several interrupts. This driver provides a handler
+ * for those interrupts which aggregates the counts (to avoid
+ * saturating the 8-bit counters) and provides a presence in
+ * /proc/bus_watcher if PROC_FS is on.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
+#include <asm/io.h>
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_int.h>
+#include <asm/sibyte/sb1250_scd.h>
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#include <asm/sibyte/bcm1480_regs.h>
+#endif
+
+
+struct bw_stats_struct {
+ uint64_t status;
+ uint32_t l2_err;
+ uint32_t memio_err;
+ int status_printed;
+ unsigned long l2_cor_d;
+ unsigned long l2_bad_d;
+ unsigned long l2_cor_t;
+ unsigned long l2_bad_t;
+ unsigned long mem_cor_d;
+ unsigned long mem_bad_d;
+ unsigned long bus_error;
+} bw_stats;
+
+
+static void print_summary(uint32_t status, uint32_t l2_err,
+ uint32_t memio_err)
+{
+ printk("Bus watcher error counters: %08x %08x\n", l2_err, memio_err);
+ printk("\nLast recorded signature:\n");
+ printk("Request %02x from %d, answered by %d with Dcode %d\n",
+ (unsigned int)(G_SCD_BERR_TID(status) & 0x3f),
+ (int)(G_SCD_BERR_TID(status) >> 6),
+ (int)G_SCD_BERR_RID(status),
+ (int)G_SCD_BERR_DCODE(status));
+}
+
+/*
+ * check_bus_watcher is exported for use in situations where we want
+ * to see the most recent status of the bus watcher, which might have
+ * already been destructively read out of the registers.
+ *
+ * notes: this is currently used by the cache error handler
+ * should provide locking against the interrupt handler
+ */
+void check_bus_watcher(void)
+{
+ u32 status, l2_err, memio_err;
+
+#ifdef CONFIG_SB1_PASS_1_WORKAROUNDS
+ /* Destructive read, clears register and interrupt */
+ status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS));
+#elif defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250)
+ /* Use non-destructive register */
+ status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS_DEBUG));
+#elif defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+ /* Use non-destructive register */
+ /* Same as 1250 except BUS_ERR_STATUS_DEBUG is in a different place. */
+ status = csr_in32(IOADDR(A_BCM1480_BUS_ERR_STATUS_DEBUG));
+#else
+#error bus watcher being built for unknown Sibyte SOC!
+#endif
+ if (!(status & 0x7fffffff)) {
+ printk("Using last values reaped by bus watcher driver\n");
+ status = bw_stats.status;
+ l2_err = bw_stats.l2_err;
+ memio_err = bw_stats.memio_err;
+ } else {
+ l2_err = csr_in32(IOADDR(A_BUS_L2_ERRORS));
+ memio_err = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
+ }
+ if (status & ~(1UL << 31))
+ print_summary(status, l2_err, memio_err);
+ else
+ printk("Bus watcher indicates no error\n");
+}
+
+#ifdef CONFIG_PROC_FS
+
+/* For simplicity, I want to assume a single read is required each
+ time */
+static int bw_proc_show(struct seq_file *m, void *v)
+{
+ struct bw_stats_struct *stats = m->private;
+
+ seq_puts(m, "SiByte Bus Watcher statistics\n");
+ seq_puts(m, "-----------------------------\n");
+ seq_printf(m, "L2-d-cor %8ld\nL2-d-bad %8ld\n",
+ stats->l2_cor_d, stats->l2_bad_d);
+ seq_printf(m, "L2-t-cor %8ld\nL2-t-bad %8ld\n",
+ stats->l2_cor_t, stats->l2_bad_t);
+ seq_printf(m, "MC-d-cor %8ld\nMC-d-bad %8ld\n",
+ stats->mem_cor_d, stats->mem_bad_d);
+ seq_printf(m, "IO-err %8ld\n", stats->bus_error);
+ seq_puts(m, "\nLast recorded signature:\n");
+ seq_printf(m, "Request %02x from %d, answered by %d with Dcode %d\n",
+ (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f),
+ (int)(G_SCD_BERR_TID(stats->status) >> 6),
+ (int)G_SCD_BERR_RID(stats->status),
+ (int)G_SCD_BERR_DCODE(stats->status));
+ /* XXXKW indicate multiple errors between printings, or stats
+ collection (or both)? */
+ if (stats->status & M_SCD_BERR_MULTERRS)
+ seq_puts(m, "Multiple errors observed since last check.\n");
+ if (stats->status_printed) {
+ seq_puts(m, "(no change since last printing)\n");
+ } else {
+ stats->status_printed = 1;
+ }
+
+ return 0;
+}
+
+static int bw_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, bw_proc_show, PDE_DATA(inode));
+}
+
+static const struct file_operations bw_proc_fops = {
+ .open = bw_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static void create_proc_decoder(struct bw_stats_struct *stats)
+{
+ struct proc_dir_entry *ent;
+
+ ent = proc_create_data("bus_watcher", S_IWUSR | S_IRUGO, NULL,
+ &bw_proc_fops, stats);
+ if (!ent) {
+ printk(KERN_INFO "Unable to initialize bus_watcher /proc entry\n");
+ return;
+ }
+}
+
+#endif /* CONFIG_PROC_FS */
+
+/*
+ * sibyte_bw_int - handle bus watcher interrupts and accumulate counts
+ *
+ * notes: possible re-entry due to multiple sources
+ * should check/indicate saturation
+ */
+static irqreturn_t sibyte_bw_int(int irq, void *data)
+{
+ struct bw_stats_struct *stats = data;
+ unsigned long cntr;
+#ifdef CONFIG_SIBYTE_BW_TRACE
+ int i;
+#endif
+
+#ifdef CONFIG_SIBYTE_BW_TRACE
+ csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG));
+ csr_out32(M_SCD_TRACE_CFG_START_READ, IOADDR(A_SCD_TRACE_CFG));
+
+ for (i=0; i<256*6; i++)
+ printk("%016llx\n",
+ (long long)__raw_readq(IOADDR(A_SCD_TRACE_READ)));
+
+ csr_out32(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
+ csr_out32(M_SCD_TRACE_CFG_START, IOADDR(A_SCD_TRACE_CFG));
+#endif
+
+ /* Destructive read, clears register and interrupt */
+ stats->status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS));
+ stats->status_printed = 0;
+
+ stats->l2_err = cntr = csr_in32(IOADDR(A_BUS_L2_ERRORS));
+ stats->l2_cor_d += G_SCD_L2ECC_CORR_D(cntr);
+ stats->l2_bad_d += G_SCD_L2ECC_BAD_D(cntr);
+ stats->l2_cor_t += G_SCD_L2ECC_CORR_T(cntr);
+ stats->l2_bad_t += G_SCD_L2ECC_BAD_T(cntr);
+ csr_out32(0, IOADDR(A_BUS_L2_ERRORS));
+
+ stats->memio_err = cntr = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
+ stats->mem_cor_d += G_SCD_MEM_ECC_CORR(cntr);
+ stats->mem_bad_d += G_SCD_MEM_ECC_BAD(cntr);
+ stats->bus_error += G_SCD_MEM_BUSERR(cntr);
+ csr_out32(0, IOADDR(A_BUS_MEM_IO_ERRORS));
+
+ return IRQ_HANDLED;
+}
+
+int __init sibyte_bus_watcher(void)
+{
+ memset(&bw_stats, 0, sizeof(struct bw_stats_struct));
+ bw_stats.status_printed = 1;
+
+ if (request_irq(K_INT_BAD_ECC, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
+ printk("Failed to register bus watcher BAD_ECC irq\n");
+ return -1;
+ }
+ if (request_irq(K_INT_COR_ECC, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
+ free_irq(K_INT_BAD_ECC, &bw_stats);
+ printk("Failed to register bus watcher COR_ECC irq\n");
+ return -1;
+ }
+ if (request_irq(K_INT_IO_BUS, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
+ free_irq(K_INT_BAD_ECC, &bw_stats);
+ free_irq(K_INT_COR_ECC, &bw_stats);
+ printk("Failed to register bus watcher IO_BUS irq\n");
+ return -1;
+ }
+
+#ifdef CONFIG_PROC_FS
+ create_proc_decoder(&bw_stats);
+#endif
+
+#ifdef CONFIG_SIBYTE_BW_TRACE
+ csr_out32((M_SCD_TRSEQ_ASAMPLE | M_SCD_TRSEQ_DSAMPLE |
+ K_SCD_TRSEQ_TRIGGER_ALL),
+ IOADDR(A_SCD_TRACE_SEQUENCE_0));
+ csr_out32(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
+ csr_out32(M_SCD_TRACE_CFG_START, IOADDR(A_SCD_TRACE_CFG));
+#endif
+
+ return 0;
+}
+
+__initcall(sibyte_bus_watcher);
#include <linux/types.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/sched.h>
#include <linux/vmalloc.h>
#include <linux/fs.h>
#include <linux/errno.h>
obj-y := setup.o irq.o time.o
obj-$(CONFIG_SMP) += smp.o
-obj-$(CONFIG_SIBYTE_BUS_WATCHER) += bus_watcher.o
+++ /dev/null
-/*
- * Copyright (C) 2002,2003 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-/*
- * The Bus Watcher monitors internal bus transactions and maintains
- * counts of transactions with error status, logging details and
- * causing one of several interrupts. This driver provides a handler
- * for those interrupts which aggregates the counts (to avoid
- * saturating the 8-bit counters) and provides a presence in
- * /proc/bus_watcher if PROC_FS is on.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-#include <linux/proc_fs.h>
-#include <linux/seq_file.h>
-#include <asm/io.h>
-
-#include <asm/sibyte/sb1250.h>
-#include <asm/sibyte/sb1250_regs.h>
-#include <asm/sibyte/sb1250_int.h>
-#include <asm/sibyte/sb1250_scd.h>
-
-
-struct bw_stats_struct {
- uint64_t status;
- uint32_t l2_err;
- uint32_t memio_err;
- int status_printed;
- unsigned long l2_cor_d;
- unsigned long l2_bad_d;
- unsigned long l2_cor_t;
- unsigned long l2_bad_t;
- unsigned long mem_cor_d;
- unsigned long mem_bad_d;
- unsigned long bus_error;
-} bw_stats;
-
-
-static void print_summary(uint32_t status, uint32_t l2_err,
- uint32_t memio_err)
-{
- printk("Bus watcher error counters: %08x %08x\n", l2_err, memio_err);
- printk("\nLast recorded signature:\n");
- printk("Request %02x from %d, answered by %d with Dcode %d\n",
- (unsigned int)(G_SCD_BERR_TID(status) & 0x3f),
- (int)(G_SCD_BERR_TID(status) >> 6),
- (int)G_SCD_BERR_RID(status),
- (int)G_SCD_BERR_DCODE(status));
-}
-
-/*
- * check_bus_watcher is exported for use in situations where we want
- * to see the most recent status of the bus watcher, which might have
- * already been destructively read out of the registers.
- *
- * notes: this is currently used by the cache error handler
- * should provide locking against the interrupt handler
- */
-void check_bus_watcher(void)
-{
- u32 status, l2_err, memio_err;
-
-#ifdef CONFIG_SB1_PASS_1_WORKAROUNDS
- /* Destructive read, clears register and interrupt */
- status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS));
-#else
- /* Use non-destructive register */
- status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS_DEBUG));
-#endif
- if (!(status & 0x7fffffff)) {
- printk("Using last values reaped by bus watcher driver\n");
- status = bw_stats.status;
- l2_err = bw_stats.l2_err;
- memio_err = bw_stats.memio_err;
- } else {
- l2_err = csr_in32(IOADDR(A_BUS_L2_ERRORS));
- memio_err = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
- }
- if (status & ~(1UL << 31))
- print_summary(status, l2_err, memio_err);
- else
- printk("Bus watcher indicates no error\n");
-}
-
-#ifdef CONFIG_PROC_FS
-
-/* For simplicity, I want to assume a single read is required each
- time */
-static int bw_proc_show(struct seq_file *m, void *v)
-{
- struct bw_stats_struct *stats = m->private;
-
- seq_puts(m, "SiByte Bus Watcher statistics\n");
- seq_puts(m, "-----------------------------\n");
- seq_printf(m, "L2-d-cor %8ld\nL2-d-bad %8ld\n",
- stats->l2_cor_d, stats->l2_bad_d);
- seq_printf(m, "L2-t-cor %8ld\nL2-t-bad %8ld\n",
- stats->l2_cor_t, stats->l2_bad_t);
- seq_printf(m, "MC-d-cor %8ld\nMC-d-bad %8ld\n",
- stats->mem_cor_d, stats->mem_bad_d);
- seq_printf(m, "IO-err %8ld\n", stats->bus_error);
- seq_puts(m, "\nLast recorded signature:\n");
- seq_printf(m, "Request %02x from %d, answered by %d with Dcode %d\n",
- (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f),
- (int)(G_SCD_BERR_TID(stats->status) >> 6),
- (int)G_SCD_BERR_RID(stats->status),
- (int)G_SCD_BERR_DCODE(stats->status));
- /* XXXKW indicate multiple errors between printings, or stats
- collection (or both)? */
- if (stats->status & M_SCD_BERR_MULTERRS)
- seq_puts(m, "Multiple errors observed since last check.\n");
- if (stats->status_printed) {
- seq_puts(m, "(no change since last printing)\n");
- } else {
- stats->status_printed = 1;
- }
-
- return 0;
-}
-
-static int bw_proc_open(struct inode *inode, struct file *file)
-{
- return single_open(file, bw_proc_show, PDE_DATA(inode));
-}
-
-static const struct file_operations bw_proc_fops = {
- .open = bw_proc_open,
- .read = seq_read,
- .llseek = seq_lseek,
- .release = single_release,
-};
-
-static void create_proc_decoder(struct bw_stats_struct *stats)
-{
- struct proc_dir_entry *ent;
-
- ent = proc_create_data("bus_watcher", S_IWUSR | S_IRUGO, NULL,
- &bw_proc_fops, stats);
- if (!ent) {
- printk(KERN_INFO "Unable to initialize bus_watcher /proc entry\n");
- return;
- }
-}
-
-#endif /* CONFIG_PROC_FS */
-
-/*
- * sibyte_bw_int - handle bus watcher interrupts and accumulate counts
- *
- * notes: possible re-entry due to multiple sources
- * should check/indicate saturation
- */
-static irqreturn_t sibyte_bw_int(int irq, void *data)
-{
- struct bw_stats_struct *stats = data;
- unsigned long cntr;
-#ifdef CONFIG_SIBYTE_BW_TRACE
- int i;
-#endif
-#ifndef CONFIG_PROC_FS
- char bw_buf[1024];
-#endif
-
-#ifdef CONFIG_SIBYTE_BW_TRACE
- csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG));
- csr_out32(M_SCD_TRACE_CFG_START_READ, IOADDR(A_SCD_TRACE_CFG));
-
- for (i=0; i<256*6; i++)
- printk("%016llx\n",
- (long long)__raw_readq(IOADDR(A_SCD_TRACE_READ)));
-
- csr_out32(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
- csr_out32(M_SCD_TRACE_CFG_START, IOADDR(A_SCD_TRACE_CFG));
-#endif
-
- /* Destructive read, clears register and interrupt */
- stats->status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS));
- stats->status_printed = 0;
-
- stats->l2_err = cntr = csr_in32(IOADDR(A_BUS_L2_ERRORS));
- stats->l2_cor_d += G_SCD_L2ECC_CORR_D(cntr);
- stats->l2_bad_d += G_SCD_L2ECC_BAD_D(cntr);
- stats->l2_cor_t += G_SCD_L2ECC_CORR_T(cntr);
- stats->l2_bad_t += G_SCD_L2ECC_BAD_T(cntr);
- csr_out32(0, IOADDR(A_BUS_L2_ERRORS));
-
- stats->memio_err = cntr = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
- stats->mem_cor_d += G_SCD_MEM_ECC_CORR(cntr);
- stats->mem_bad_d += G_SCD_MEM_ECC_BAD(cntr);
- stats->bus_error += G_SCD_MEM_BUSERR(cntr);
- csr_out32(0, IOADDR(A_BUS_MEM_IO_ERRORS));
-
- return IRQ_HANDLED;
-}
-
-int __init sibyte_bus_watcher(void)
-{
- memset(&bw_stats, 0, sizeof(struct bw_stats_struct));
- bw_stats.status_printed = 1;
-
- if (request_irq(K_INT_BAD_ECC, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
- printk("Failed to register bus watcher BAD_ECC irq\n");
- return -1;
- }
- if (request_irq(K_INT_COR_ECC, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
- free_irq(K_INT_BAD_ECC, &bw_stats);
- printk("Failed to register bus watcher COR_ECC irq\n");
- return -1;
- }
- if (request_irq(K_INT_IO_BUS, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
- free_irq(K_INT_BAD_ECC, &bw_stats);
- free_irq(K_INT_COR_ECC, &bw_stats);
- printk("Failed to register bus watcher IO_BUS irq\n");
- return -1;
- }
-
-#ifdef CONFIG_PROC_FS
- create_proc_decoder(&bw_stats);
-#endif
-
-#ifdef CONFIG_SIBYTE_BW_TRACE
- csr_out32((M_SCD_TRSEQ_ASAMPLE | M_SCD_TRSEQ_DSAMPLE |
- K_SCD_TRSEQ_TRIGGER_ALL),
- IOADDR(A_SCD_TRACE_SEQUENCE_0));
- csr_out32(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
- csr_out32(M_SCD_TRACE_CFG_START, IOADDR(A_SCD_TRACE_CFG));
-#endif
-
- return 0;
-}
-
-__initcall(sibyte_bus_watcher);
extern struct pci_ops sni_pcimt_ops;
+#ifdef CONFIG_PCI
static struct pci_controller sni_controller = {
.pci_ops = &sni_pcimt_ops,
.mem_resource = &sni_mem_resource,
.io_offset = 0x00000000UL,
.io_map_base = SNI_PORT_BASE
};
+#endif
static void enable_pcimt_irq(struct irq_data *d)
{
}
};
-static struct resource sni_mem_resource = {
- .start = 0x18000000UL,
- .end = 0x1fbfffffUL,
- .name = "PCIT PCI MEM",
- .flags = IORESOURCE_MEM
-};
-
static void __init sni_pcit_resource_init(void)
{
int i;
extern struct pci_ops sni_pcit_ops;
+#ifdef CONFIG_PCI
+static struct resource sni_mem_resource = {
+ .start = 0x18000000UL,
+ .end = 0x1fbfffffUL,
+ .name = "PCIT PCI MEM",
+ .flags = IORESOURCE_MEM
+};
+
static struct pci_controller sni_pcit_controller = {
.pci_ops = &sni_pcit_ops,
.mem_resource = &sni_mem_resource,
.io_offset = 0x00000000UL,
.io_map_base = SNI_PORT_BASE
};
+#endif /* CONFIG_PCI */
static void enable_pcit_irq(struct irq_data *d)
{
+++ /dev/null
-#
-# This file is subject to the terms and conditions of the GNU General Public
-# License. See the file "COPYING" in the main directory of this archive
-# for more details.
-#
-# Copyright 2006 Wind River System, Inc.
-# Author: Rongkai.Zhan <rongkai.zhan@windriver.com>
-#
-# Makefile for the Wind River MIPS 4Kc PPMC Eval Board
-#
-
-obj-y += irq.o pci.o reset.o serial.o setup.o time.o
+++ /dev/null
-#
-# Wind River PPMC Board (4KC + GT64120)
-#
-platform-$(CONFIG_WR_PPMC) += wrppmc/
-cflags-$(CONFIG_WR_PPMC) += \
- -I$(srctree)/arch/mips/include/asm/mach-wrppmc
-load-$(CONFIG_WR_PPMC) += 0xffffffff80100000
+++ /dev/null
-/*
- * irq.c: GT64120 Interrupt Controller
- *
- * Copyright (C) 2006, Wind River System Inc.
- * Author: Rongkai.Zhan, <rongkai.zhan@windriver.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#include <linux/hardirq.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/gt64120.h>
-#include <asm/irq_cpu.h>
-#include <asm/mipsregs.h>
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
-
- if (pending & STATUSF_IP7)
- do_IRQ(WRPPMC_MIPS_TIMER_IRQ); /* CPU Compare/Count internal timer */
- else if (pending & STATUSF_IP6)
- do_IRQ(WRPPMC_UART16550_IRQ); /* UART 16550 port */
- else if (pending & STATUSF_IP3)
- do_IRQ(WRPPMC_PCI_INTA_IRQ); /* PCI INT_A */
- else
- spurious_interrupt();
-}
-
-/**
- * Initialize GT64120 Interrupt Controller
- */
-void gt64120_init_pic(void)
-{
- /* clear CPU Interrupt Cause Registers */
- GT_WRITE(GT_INTRCAUSE_OFS, (0x1F << 21));
- GT_WRITE(GT_HINTRCAUSE_OFS, 0x00);
-
- /* Disable all interrupts from GT64120 bridge chip */
- GT_WRITE(GT_INTRMASK_OFS, 0x00);
- GT_WRITE(GT_HINTRMASK_OFS, 0x00);
- GT_WRITE(GT_PCI0_ICMASK_OFS, 0x00);
- GT_WRITE(GT_PCI0_HICMASK_OFS, 0x00);
-}
-
-void __init arch_init_irq(void)
-{
- /* IRQ 0 - 7 are for MIPS common irq_cpu controller */
- mips_cpu_irq_init();
-
- gt64120_init_pic();
-}
+++ /dev/null
-/*
- * pci.c: GT64120 PCI support.
- *
- * Copyright (C) 2006, Wind River System Inc. Rongkai.Zhan <rongkai.zhan@windriver.com>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-
-#include <asm/gt64120.h>
-
-extern struct pci_ops gt64xxx_pci0_ops;
-
-static struct resource pci0_io_resource = {
- .name = "pci_0 io",
- .start = GT_PCI_IO_BASE,
- .end = GT_PCI_IO_BASE + GT_PCI_IO_SIZE - 1,
- .flags = IORESOURCE_IO,
-};
-
-static struct resource pci0_mem_resource = {
- .name = "pci_0 memory",
- .start = GT_PCI_MEM_BASE,
- .end = GT_PCI_MEM_BASE + GT_PCI_MEM_SIZE - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct pci_controller hose_0 = {
- .pci_ops = >64xxx_pci0_ops,
- .io_resource = &pci0_io_resource,
- .mem_resource = &pci0_mem_resource,
-};
-
-static int __init gt64120_pci_init(void)
-{
- (void) GT_READ(GT_PCI0_CMD_OFS); /* Huh??? -- Ralf */
- (void) GT_READ(GT_PCI0_BARE_OFS);
-
- /* reset the whole PCI I/O space range */
- ioport_resource.start = GT_PCI_IO_BASE;
- ioport_resource.end = GT_PCI_IO_BASE + GT_PCI_IO_SIZE - 1;
-
- register_pci_controller(&hose_0);
- return 0;
-}
-
-arch_initcall(gt64120_pci_init);
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1997 Ralf Baechle
- */
-#include <linux/irqflags.h>
-#include <linux/kernel.h>
-
-#include <asm/cacheflush.h>
-#include <asm/idle.h>
-#include <asm/mipsregs.h>
-#include <asm/processor.h>
-
-void wrppmc_machine_restart(char *command)
-{
- /*
- * Ouch, we're still alive ... This time we take the silver bullet ...
- * ... and find that we leave the hardware in a state in which the
- * kernel in the flush locks up somewhen during of after the PCI
- * detection stuff.
- */
- local_irq_disable();
- set_c0_status(ST0_BEV | ST0_ERL);
- change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
- flush_cache_all();
- write_c0_wired(0);
- __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-}
-
-void wrppmc_machine_halt(void)
-{
- local_irq_disable();
-
- printk(KERN_NOTICE "You can safely turn off the power\n");
- while (1) {
- if (cpu_wait)
- cpu_wait();
- }
-}
+++ /dev/null
-/*
- * Registration of WRPPMC UART platform device.
- *
- * Copyright (C) 2007 Yoichi Yuasa <yuasa@linux-mips.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
- */
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-
-#include <asm/gt64120.h>
-
-static struct resource wrppmc_uart_resource[] __initdata = {
- {
- .start = WRPPMC_UART16550_BASE,
- .end = WRPPMC_UART16550_BASE + 7,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = WRPPMC_UART16550_IRQ,
- .end = WRPPMC_UART16550_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct plat_serial8250_port wrppmc_serial8250_port[] = {
- {
- .irq = WRPPMC_UART16550_IRQ,
- .uartclk = WRPPMC_UART16550_CLOCK,
- .iotype = UPIO_MEM,
- .flags = UPF_IOREMAP | UPF_SKIP_TEST,
- .mapbase = WRPPMC_UART16550_BASE,
- },
- {},
-};
-
-static __init int wrppmc_uart_add(void)
-{
- struct platform_device *pdev;
- int retval;
-
- pdev = platform_device_alloc("serial8250", -1);
- if (!pdev)
- return -ENOMEM;
-
- pdev->id = PLAT8250_DEV_PLATFORM;
- pdev->dev.platform_data = wrppmc_serial8250_port;
-
- retval = platform_device_add_resources(pdev, wrppmc_uart_resource,
- ARRAY_SIZE(wrppmc_uart_resource));
- if (retval)
- goto err_free_device;
-
- retval = platform_device_add(pdev);
- if (retval)
- goto err_free_device;
-
- return 0;
-
-err_free_device:
- platform_device_put(pdev);
-
- return retval;
-}
-device_initcall(wrppmc_uart_add);
+++ /dev/null
-/*
- * setup.c: Setup pointers to hardware dependent routines.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1996, 1997, 2004 by Ralf Baechle (ralf@linux-mips.org)
- * Copyright (C) 2006, Wind River System Inc. Rongkai.zhan <rongkai.zhan@windriver.com>
- */
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-#include <linux/pm.h>
-
-#include <asm/io.h>
-#include <asm/bootinfo.h>
-#include <asm/reboot.h>
-#include <asm/time.h>
-#include <asm/gt64120.h>
-
-unsigned long gt64120_base = KSEG1ADDR(0x14000000);
-
-#ifdef WRPPMC_EARLY_DEBUG
-
-static volatile unsigned char * wrppmc_led = \
- (volatile unsigned char *)KSEG1ADDR(WRPPMC_LED_BASE);
-
-/*
- * PPMC LED control register:
- * -) bit[0] controls DS1 LED (1 - OFF, 0 - ON)
- * -) bit[1] controls DS2 LED (1 - OFF, 0 - ON)
- * -) bit[2] controls DS4 LED (1 - OFF, 0 - ON)
- */
-void wrppmc_led_on(int mask)
-{
- unsigned char value = *wrppmc_led;
-
- value &= (0xF8 | mask);
- *wrppmc_led = value;
-}
-
-/* If mask = 0, turn off all LEDs */
-void wrppmc_led_off(int mask)
-{
- unsigned char value = *wrppmc_led;
-
- value |= (0x7 & mask);
- *wrppmc_led = value;
-}
-
-/*
- * We assume that bootloader has initialized UART16550 correctly
- */
-void __init wrppmc_early_putc(char ch)
-{
- static volatile unsigned char *wrppmc_uart = \
- (volatile unsigned char *)KSEG1ADDR(WRPPMC_UART16550_BASE);
- unsigned char value;
-
- /* Wait until Transmit-Holding-Register is empty */
- while (1) {
- value = *(wrppmc_uart + 5);
- if (value & 0x20)
- break;
- }
-
- *wrppmc_uart = ch;
-}
-
-void __init wrppmc_early_printk(const char *fmt, ...)
-{
- static char pbuf[256] = {'\0', };
- char *ch = pbuf;
- va_list args;
- unsigned int i;
-
- memset(pbuf, 0, 256);
- va_start(args, fmt);
- i = vsprintf(pbuf, fmt, args);
- va_end(args);
-
- /* Print the string */
- while (*ch != '\0') {
- wrppmc_early_putc(*ch);
- /* if print '\n', also print '\r' */
- if (*ch++ == '\n')
- wrppmc_early_putc('\r');
- }
-}
-#endif /* WRPPMC_EARLY_DEBUG */
-
-void __init prom_free_prom_memory(void)
-{
-}
-
-void __init plat_mem_setup(void)
-{
- extern void wrppmc_machine_restart(char *command);
- extern void wrppmc_machine_halt(void);
-
- _machine_restart = wrppmc_machine_restart;
- _machine_halt = wrppmc_machine_halt;
- pm_power_off = wrppmc_machine_halt;
-
- /* This makes the operations of 'in/out[bwl]' to the
- * physical address ( < KSEG0) can work via KSEG1
- */
- set_io_port_base(KSEG1);
-}
-
-const char *get_system_type(void)
-{
- return "Wind River PPMC (GT64120)";
-}
-
-/*
- * Initializes basic routines and structures pointers, memory size (as
- * given by the bios and saves the command line.
- */
-void __init prom_init(void)
-{
- add_memory_region(WRPPMC_SDRAM_SCS0_BASE, WRPPMC_SDRAM_SCS0_SIZE, BOOT_MEM_RAM);
- add_memory_region(WRPPMC_BOOTROM_BASE, WRPPMC_BOOTROM_SIZE, BOOT_MEM_ROM_DATA);
-
- wrppmc_early_printk("prom_init: GT64120 SDRAM Bank 0: 0x%x - 0x%08lx\n",
- WRPPMC_SDRAM_SCS0_BASE, (WRPPMC_SDRAM_SCS0_BASE + WRPPMC_SDRAM_SCS0_SIZE));
-}
+++ /dev/null
-/*
- * time.c: MIPS CPU Count/Compare timer hookup
- *
- * Author: Mark.Zhan, <rongkai.zhan@windriver.com>
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1996, 1997, 2004 by Ralf Baechle (ralf@linux-mips.org)
- * Copyright (C) 2006, Wind River System Inc.
- */
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-
-#include <asm/gt64120.h>
-#include <asm/time.h>
-
-#define WRPPMC_CPU_CLK_FREQ 40000000 /* 40MHZ */
-
-/*
- * Estimate CPU frequency. Sets mips_hpt_frequency as a side-effect
- *
- * NOTE: We disable all GT64120 timers, and use MIPS processor internal
- * timer as the source of kernel clock tick.
- */
-void __init plat_time_init(void)
-{
- /* Disable GT64120 timers */
- GT_WRITE(GT_TC_CONTROL_OFS, 0x00);
- GT_WRITE(GT_TC0_OFS, 0x00);
- GT_WRITE(GT_TC1_OFS, 0x00);
- GT_WRITE(GT_TC2_OFS, 0x00);
- GT_WRITE(GT_TC3_OFS, 0x00);
-
- /* Use MIPS compare/count internal timer */
- mips_hpt_frequency = WRPPMC_CPU_CLK_FREQ;
-}
config PATA_OCTEON_CF
tristate "OCTEON Boot Bus Compact Flash support"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
help
This option enables a polled compact flash driver for use with
compact flash cards attached to the OCTEON boot bus.
config HW_RANDOM_OCTEON
tristate "Octeon Random Number Generator support"
- depends on HW_RANDOM && CPU_CAVIUM_OCTEON
+ depends on HW_RANDOM && CAVIUM_OCTEON_SOC
default HW_RANDOM
---help---
This driver provides kernel-side support for the Random Number
config EDAC_OCTEON_L2C
tristate "Cavium Octeon Secondary Caches (L2C)"
- depends on EDAC_MM_EDAC && CPU_CAVIUM_OCTEON
+ depends on EDAC_MM_EDAC && CAVIUM_OCTEON_SOC
help
Support for error detection and correction on the
Cavium Octeon family of SOCs.
config EDAC_OCTEON_LMC
tristate "Cavium Octeon DRAM Memory Controller (LMC)"
- depends on EDAC_MM_EDAC && CPU_CAVIUM_OCTEON
+ depends on EDAC_MM_EDAC && CAVIUM_OCTEON_SOC
help
Support for error detection and correction on the
Cavium Octeon family of SOCs.
config EDAC_OCTEON_PCI
tristate "Cavium Octeon PCI Controller"
- depends on EDAC_MM_EDAC && PCI && CPU_CAVIUM_OCTEON
+ depends on EDAC_MM_EDAC && PCI && CAVIUM_OCTEON_SOC
help
Support for error detection and correction on the
Cavium Octeon family of SOCs.
config I2C_OCTEON
tristate "Cavium OCTEON I2C bus support"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
help
Say yes if you want to support the I2C serial bus on Cavium
OCTEON SOC.
config OCTEON_MGMT_ETHERNET
tristate "Octeon Management port ethernet driver (CN5XXX, CN6XXX)"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
select PHYLIB
select MDIO_OCTEON
default y
config MDIO_OCTEON
tristate "Support for MDIO buses on Octeon SOCs"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
default y
help
#include <linux/rio_drv.h>
#include <linux/rio_ids.h>
#include <linux/delay.h>
+
+#include <asm/page.h>
#include "../rio.h"
#define LOCAL_RTE_CONF_DESTID_SEL 0x010070
config SPI_OCTEON
tristate "Cavium OCTEON SPI controller"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
help
SPI host driver for the hardware found on some Cavium OCTEON
SOCs.
# Assumption: We are on embedded, if we compile the MIPS core.
config SSB_EMBEDDED
bool
- depends on SSB_DRIVER_MIPS
+ depends on SSB_DRIVER_MIPS && SSB_PCICORE_HOSTMODE
default y
config SSB_DRIVER_EXTIF
config OCTEON_ETHERNET
tristate "Cavium Networks Octeon Ethernet support"
- depends on CPU_CAVIUM_OCTEON && NETDEVICES
+ depends on CAVIUM_OCTEON_SOC && NETDEVICES
select PHYLIB
select MDIO_OCTEON
help
#include <linux/clk.h>
#include <linux/pm_runtime.h>
+#include <asm/byteorder.h>
+
#include "8250.h"
/* Offsets for the DesignWare specific registers */
int last_lcr;
int line;
struct clk *clk;
+ u8 usr_reg;
};
static void dw8250_serial_out(struct uart_port *p, int offset, int value)
return readb(p->membase + offset);
}
+/* Read Back (rb) version to ensure register access ording. */
+static void dw8250_serial_out_rb(struct uart_port *p, int offset, int value)
+{
+ dw8250_serial_out(p, offset, value);
+ dw8250_serial_in(p, UART_LCR);
+}
+
static void dw8250_serial_out32(struct uart_port *p, int offset, int value)
{
struct dw8250_data *d = p->private_data;
return 1;
} else if ((iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
/* Clear the USR and write the LCR again. */
- (void)p->serial_in(p, DW_UART_USR);
+ (void)p->serial_in(p, d->usr_reg);
p->serial_out(p, UART_LCR, d->last_lcr);
return 1;
pm_runtime_put_sync_suspend(port->dev);
}
-static int dw8250_probe_of(struct uart_port *p)
+static void dw8250_setup_port(struct uart_8250_port *up)
+{
+ struct uart_port *p = &up->port;
+ u32 reg = readl(p->membase + DW_UART_UCV);
+
+ /*
+ * If the Component Version Register returns zero, we know that
+ * ADDITIONAL_FEATURES are not enabled. No need to go any further.
+ */
+ if (!reg)
+ return;
+
+ dev_dbg_ratelimited(p->dev, "Designware UART version %c.%c%c\n",
+ (reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
+
+ reg = readl(p->membase + DW_UART_CPR);
+ if (!reg)
+ return;
+
+ /* Select the type based on fifo */
+ if (reg & DW_UART_CPR_FIFO_MODE) {
+ p->type = PORT_16550A;
+ p->flags |= UPF_FIXED_TYPE;
+ p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
+ up->tx_loadsz = p->fifosize;
+ up->capabilities = UART_CAP_FIFO;
+ }
+
+ if (reg & DW_UART_CPR_AFCE_MODE)
+ up->capabilities |= UART_CAP_AFE;
+}
+
+static int dw8250_probe_of(struct uart_port *p,
+ struct dw8250_data *data)
{
struct device_node *np = p->dev->of_node;
u32 val;
-
- if (!of_property_read_u32(np, "reg-io-width", &val)) {
+ bool has_ucv = true;
+
+ if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) {
+#ifdef __BIG_ENDIAN
+ /*
+ * Low order bits of these 64-bit registers, when
+ * accessed as a byte, are 7 bytes further down in the
+ * address space in big endian mode.
+ */
+ p->membase += 7;
+#endif
+ p->serial_out = dw8250_serial_out_rb;
+ p->flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
+ p->type = PORT_OCTEON;
+ data->usr_reg = 0x27;
+ has_ucv = false;
+ } else if (!of_property_read_u32(np, "reg-io-width", &val)) {
switch (val) {
case 1:
break;
return -EINVAL;
}
}
+ if (has_ucv)
+ dw8250_setup_port(container_of(p, struct uart_8250_port, port));
if (!of_property_read_u32(np, "reg-shift", &val))
p->regshift = val;
const struct acpi_device_id *id;
struct uart_port *p = &up->port;
+ dw8250_setup_port(up);
+
id = acpi_match_device(p->dev->driver->acpi_match_table, p->dev);
if (!id)
return -ENODEV;
}
#endif /* CONFIG_ACPI */
-static void dw8250_setup_port(struct uart_8250_port *up)
-{
- struct uart_port *p = &up->port;
- u32 reg = readl(p->membase + DW_UART_UCV);
-
- /*
- * If the Component Version Register returns zero, we know that
- * ADDITIONAL_FEATURES are not enabled. No need to go any further.
- */
- if (!reg)
- return;
-
- dev_dbg_ratelimited(p->dev, "Designware UART version %c.%c%c\n",
- (reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
-
- reg = readl(p->membase + DW_UART_CPR);
- if (!reg)
- return;
-
- /* Select the type based on fifo */
- if (reg & DW_UART_CPR_FIFO_MODE) {
- p->type = PORT_16550A;
- p->flags |= UPF_FIXED_TYPE;
- p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
- up->tx_loadsz = p->fifosize;
- up->capabilities = UART_CAP_FIFO;
- }
-
- if (reg & DW_UART_CPR_AFCE_MODE)
- up->capabilities |= UART_CAP_AFE;
-}
-
static int dw8250_probe(struct platform_device *pdev)
{
struct uart_8250_port uart = {};
if (!data)
return -ENOMEM;
+ data->usr_reg = DW_UART_USR;
data->clk = devm_clk_get(&pdev->dev, NULL);
if (!IS_ERR(data->clk)) {
clk_prepare_enable(data->clk);
uart.port.serial_out = dw8250_serial_out;
uart.port.private_data = data;
- dw8250_setup_port(&uart);
-
if (pdev->dev.of_node) {
- err = dw8250_probe_of(&uart.port);
+ err = dw8250_probe_of(&uart.port, data);
if (err)
return err;
} else if (ACPI_HANDLE(&pdev->dev)) {
static const struct of_device_id dw8250_of_match[] = {
{ .compatible = "snps,dw-apb-uart" },
+ { .compatible = "cavium,octeon-3860-uart" },
{ /* Sentinel */ }
};
MODULE_DEVICE_TABLE(of, dw8250_of_match);
config USB_OCTEON_EHCI
bool "Octeon on-chip EHCI support"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
default n
select USB_EHCI_BIG_ENDIAN_MMIO
help
config USB_OCTEON_OHCI
bool "Octeon on-chip OHCI support"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
default USB_OCTEON_EHCI
select USB_OHCI_BIG_ENDIAN_MMIO
select USB_OHCI_LITTLE_ENDIAN
config OCTEON_WDT
tristate "Cavium OCTEON SOC family Watchdog Timer"
- depends on CPU_CAVIUM_OCTEON
+ depends on CAVIUM_OCTEON_SOC
default y
select EXPORT_UASM if OCTEON_WDT = m
help
* get the remaining count from the ... count register
* which is 1*8 before the config register
*/
- ret = put_user(__raw_readq(user_dog - 8) / 1000000, p);
+ ret = put_user((u32)__raw_readq(user_dog - 8) / 1000000, p);
break;
}
return ret;
header-y += ax25.h
header-y += b1lli.h
header-y += baycom.h
+header-y += bcm933xx_hcs.h
header-y += bfs_fs.h
header-y += binfmts.h
header-y += blkpg.h
--- /dev/null
+/*
+ * Broadcom Cable Modem firmware format
+ */
+
+#ifndef __BCM933XX_HCS_H
+#define __BCM933XX_HCS_H
+
+#include <linux/types.h>
+
+struct bcm_hcs {
+ __u16 magic;
+ __u16 control;
+ __u16 rev_maj;
+ __u16 rev_min;
+ __u32 build_date;
+ __u32 filelen;
+ __u32 ldaddress;
+ char filename[64];
+ __u16 hcs;
+ __u16 her_znaet_chto;
+ __u32 crc;
+};
+
+#endif /* __BCM933XX_HCS */
domain = controller ? irq_find_host(controller) : irq_default_domain;
if (!domain) {
-#ifdef CONFIG_MIPS
- /*
- * Workaround to avoid breaking interrupt controller drivers
- * that don't yet register an irq_domain. This is temporary
- * code. ~~~gcl, Feb 24, 2012
- *
- * Scheduled for removal in Linux v3.6. That should be enough
- * time.
- */
- if (intsize > 0)
- return intspec[0];
-#endif
pr_warn("no irq domain found for %s !\n",
of_node_full_name(controller));
return 0;
depends on FAULT_INJECTION_DEBUG_FS && STACKTRACE_SUPPORT
depends on !X86_64
select STACKTRACE
- select FRAME_POINTER if !PPC && !S390 && !MICROBLAZE && !ARM_UNWIND
+ select FRAME_POINTER if !MIPS && !PPC && !S390 && !MICROBLAZE && !ARM_UNWIND
help
Provide stacktrace filter for fault-injection capabilities
projects / linux.git / commitdiff