--- /dev/null
+/******************************************************************************
+ *
+ * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
+ *
+ *
+ ******************************************************************************/
+#ifndef __RTL8188E_HAL_H__
+#define __RTL8188E_HAL_H__
+
+
+/* include HAL Related header after HAL Related compiling flags */
+#include "rtl8188e_spec.h"
+#include "Hal8188EPhyReg.h"
+#include "Hal8188EPhyCfg.h"
+#include "rtl8188e_rf.h"
+#include "rtl8188e_dm.h"
+#include "rtl8188e_recv.h"
+#include "rtl8188e_xmit.h"
+#include "rtl8188e_cmd.h"
+#include "Hal8188EPwrSeq.h"
+#include "rtl8188e_sreset.h"
+#include "rtw_efuse.h"
+
+#include "odm_precomp.h"
+
+/* Fw Array */
+#define Rtl8188E_FwImageArray Rtl8188EFwImgArray
+#define Rtl8188E_FWImgArrayLength Rtl8188EFWImgArrayLength
+
+#define RTL8188E_FW_UMC_IMG "rtl8188E\\rtl8188efw.bin"
+#define RTL8188E_PHY_REG "rtl8188E\\PHY_REG_1T.txt"
+#define RTL8188E_PHY_RADIO_A "rtl8188E\\radio_a_1T.txt"
+#define RTL8188E_PHY_RADIO_B "rtl8188E\\radio_b_1T.txt"
+#define RTL8188E_AGC_TAB "rtl8188E\\AGC_TAB_1T.txt"
+#define RTL8188E_PHY_MACREG "rtl8188E\\MAC_REG.txt"
+#define RTL8188E_PHY_REG_PG "rtl8188E\\PHY_REG_PG.txt"
+#define RTL8188E_PHY_REG_MP "rtl8188E\\PHY_REG_MP.txt"
+
+/* RTL8188E Power Configuration CMDs for USB/SDIO interfaces */
+#define Rtl8188E_NIC_PWR_ON_FLOW rtl8188E_power_on_flow
+#define Rtl8188E_NIC_RF_OFF_FLOW rtl8188E_radio_off_flow
+#define Rtl8188E_NIC_DISABLE_FLOW rtl8188E_card_disable_flow
+#define Rtl8188E_NIC_ENABLE_FLOW rtl8188E_card_enable_flow
+#define Rtl8188E_NIC_SUSPEND_FLOW rtl8188E_suspend_flow
+#define Rtl8188E_NIC_RESUME_FLOW rtl8188E_resume_flow
+#define Rtl8188E_NIC_PDN_FLOW rtl8188E_hwpdn_flow
+#define Rtl8188E_NIC_LPS_ENTER_FLOW rtl8188E_enter_lps_flow
+#define Rtl8188E_NIC_LPS_LEAVE_FLOW rtl8188E_leave_lps_flow
+
+#define DRVINFO_SZ 4 /* unit is 8bytes */
+#define PageNum_128(_Len) (u32)(((_Len)>>7) + ((_Len) & 0x7F ? 1 : 0))
+
+/* download firmware related data structure */
+#define FW_8188E_SIZE 0x4000 /* 16384,16k */
+#define FW_8188E_START_ADDRESS 0x1000
+#define FW_8188E_END_ADDRESS 0x1FFF /* 0x5FFF */
+
+#define MAX_PAGE_SIZE 4096 /* @ page : 4k bytes */
+
+#define IS_FW_HEADER_EXIST(_pFwHdr) \
+ ((le16_to_cpu(_pFwHdr->Signature)&0xFFF0) == 0x92C0 || \
+ (le16_to_cpu(_pFwHdr->Signature)&0xFFF0) == 0x88C0 || \
+ (le16_to_cpu(_pFwHdr->Signature)&0xFFF0) == 0x2300 || \
+ (le16_to_cpu(_pFwHdr->Signature)&0xFFF0) == 0x88E0)
+
+enum firmware_source {
+ FW_SOURCE_IMG_FILE = 0,
+ FW_SOURCE_HEADER_FILE = 1, /* from header file */
+};
+
+struct rt_firmware {
+ enum firmware_source eFWSource;
+ u8 *szFwBuffer;
+ u32 ulFwLength;
+};
+
+/* This structure must be careful with byte-ordering */
+
+struct rt_firmware_hdr {
+ /* 8-byte alinment required */
+ /* LONG WORD 0 ---- */
+ __le16 Signature; /* 92C0: test chip; 92C,
+ * 88C0: test chip; 88C1: MP A-cut;
+ * 92C1: MP A-cut */
+ u8 Category; /* AP/NIC and USB/PCI */
+ u8 Function; /* Reserved for different FW function
+ * indcation, for further use when
+ * driver needs to download different
+ * FW for different conditions */
+ __le16 Version; /* FW Version */
+ u8 Subversion; /* FW Subversion, default 0x00 */
+ u16 Rsvd1;
+
+ /* LONG WORD 1 ---- */
+ u8 Month; /* Release time Month field */
+ u8 Date; /* Release time Date field */
+ u8 Hour; /* Release time Hour field */
+ u8 Minute; /* Release time Minute field */
+ __le16 RamCodeSize; /* The size of RAM code */
+ u8 Foundry;
+ u8 Rsvd2;
+
+ /* LONG WORD 2 ---- */
+ __le32 SvnIdx; /* The SVN entry index */
+ u32 Rsvd3;
+
+ /* LONG WORD 3 ---- */
+ u32 Rsvd4;
+ u32 Rsvd5;
+};
+
+#define DRIVER_EARLY_INT_TIME 0x05
+#define BCN_DMA_ATIME_INT_TIME 0x02
+
+enum usb_rx_agg_mode {
+ USB_RX_AGG_DISABLE,
+ USB_RX_AGG_DMA,
+ USB_RX_AGG_USB,
+ USB_RX_AGG_MIX
+};
+
+#define MAX_RX_DMA_BUFFER_SIZE_88E \
+ 0x2400 /* 9k for 88E nornal chip , MaxRxBuff=10k-max(TxReportSize(64*8),
+ * WOLPattern(16*24)) */
+
+#define MAX_TX_REPORT_BUFFER_SIZE 0x0400 /* 1k */
+
+
+/* BK, BE, VI, VO, HCCA, MANAGEMENT, COMMAND, HIGH, BEACON. */
+#define MAX_TX_QUEUE 9
+
+#define TX_SELE_HQ BIT(0) /* High Queue */
+#define TX_SELE_LQ BIT(1) /* Low Queue */
+#define TX_SELE_NQ BIT(2) /* Normal Queue */
+
+/* Note: We will divide number of page equally for each queue other
+ * than public queue! */
+/* 22k = 22528 bytes = 176 pages (@page = 128 bytes) */
+/* must reserved about 7 pages for LPS => 176-7 = 169 (0xA9) */
+/* 2*BCN / 1*ps-poll / 1*null-data /1*prob_rsp /1*QOS null-data /1*BT QOS
+ * null-data */
+
+#define TX_TOTAL_PAGE_NUMBER_88E 0xA9/* 169 (21632=> 21k) */
+
+#define TX_PAGE_BOUNDARY_88E (TX_TOTAL_PAGE_NUMBER_88E + 1)
+
+/* Note: For Normal Chip Setting ,modify later */
+#define WMM_NORMAL_TX_TOTAL_PAGE_NUMBER \
+ TX_TOTAL_PAGE_NUMBER_88E /* 0xA9 , 0xb0=>176=>22k */
+#define WMM_NORMAL_TX_PAGE_BOUNDARY_88E \
+ (WMM_NORMAL_TX_TOTAL_PAGE_NUMBER + 1) /* 0xA9 */
+
+/* Chip specific */
+#define CHIP_BONDING_IDENTIFIER(_value) (((_value)>>22)&0x3)
+#define CHIP_BONDING_92C_1T2R 0x1
+#define CHIP_BONDING_88C_USB_MCARD 0x2
+#define CHIP_BONDING_88C_USB_HP 0x1
+#include "HalVerDef.h"
+#include "hal_com.h"
+
+/* Channel Plan */
+enum ChannelPlan {
+ CHPL_FCC = 0,
+ CHPL_IC = 1,
+ CHPL_ETSI = 2,
+ CHPL_SPA = 3,
+ CHPL_FRANCE = 4,
+ CHPL_MKK = 5,
+ CHPL_MKK1 = 6,
+ CHPL_ISRAEL = 7,
+ CHPL_TELEC = 8,
+ CHPL_GLOBAL = 9,
+ CHPL_WORLD = 10,
+};
+
+struct txpowerinfo24g {
+ u8 IndexCCK_Base[MAX_RF_PATH][MAX_CHNL_GROUP_24G];
+ u8 IndexBW40_Base[MAX_RF_PATH][MAX_CHNL_GROUP_24G-1];
+ /* If only one tx, only BW20 and OFDM are used. */
+ s8 CCK_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+ s8 OFDM_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+ s8 BW20_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+ s8 BW40_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+};
+
+#define EFUSE_REAL_CONTENT_LEN 512
+#define EFUSE_MAP_LEN 128
+#define EFUSE_MAX_SECTION 16
+#define EFUSE_IC_ID_OFFSET 506 /* For some inferior IC purpose*/
+#define AVAILABLE_EFUSE_ADDR(addr) (addr < EFUSE_REAL_CONTENT_LEN)
+/* To prevent out of boundary programming case, */
+/* leave 1byte and program full section */
+/* 9bytes + 1byt + 5bytes and pre 1byte. */
+/* For worst case: */
+/* | 1byte|----8bytes----|1byte|--5bytes--| */
+/* | | Reserved(14bytes) | */
+
+/* PG data exclude header, dummy 6 bytes frome CP test and reserved 1byte. */
+#define EFUSE_OOB_PROTECT_BYTES 15
+
+#define HWSET_MAX_SIZE_88E 512
+
+#define EFUSE_REAL_CONTENT_LEN_88E 256
+#define EFUSE_MAP_LEN_88E 512
+#define EFUSE_MAX_SECTION_88E 64
+#define EFUSE_MAX_WORD_UNIT_88E 4
+#define EFUSE_IC_ID_OFFSET_88E 506
+#define AVAILABLE_EFUSE_ADDR_88E(addr) \
+ (addr < EFUSE_REAL_CONTENT_LEN_88E)
+/* To prevent out of boundary programming case, leave 1byte and program
+ * full section */
+/* 9bytes + 1byt + 5bytes and pre 1byte. */
+/* For worst case: */
+/* | 2byte|----8bytes----|1byte|--7bytes--| 92D */
+/* PG data exclude header, dummy 7 bytes frome CP test and reserved 1byte. */
+#define EFUSE_OOB_PROTECT_BYTES_88E 18
+#define EFUSE_PROTECT_BYTES_BANK_88E 16
+
+/* EFUSE for BT definition */
+#define EFUSE_BT_REAL_CONTENT_LEN 1536 /* 512*3 */
+#define EFUSE_BT_MAP_LEN 1024 /* 1k bytes */
+#define EFUSE_BT_MAX_SECTION 128 /* 1024/8 */
+
+#define EFUSE_PROTECT_BYTES_BANK 16
+
+/* For RTL8723 WiFi/BT/GPS multi-function configuration. */
+enum rt_multi_func {
+ RT_MULTI_FUNC_NONE = 0x00,
+ RT_MULTI_FUNC_WIFI = 0x01,
+ RT_MULTI_FUNC_BT = 0x02,
+ RT_MULTI_FUNC_GPS = 0x04,
+};
+
+/* For RTL8723 regulator mode. */
+enum rt_regulator_mode {
+ RT_SWITCHING_REGULATOR = 0,
+ RT_LDO_REGULATOR = 1,
+};
+
+struct hal_data_8188e {
+ struct HAL_VERSION VersionID;
+ enum rt_multi_func MultiFunc; /* For multi-function consideration. */
+ enum rt_regulator_mode RegulatorMode; /* switching regulator or LDO */
+ u16 CustomerID;
+
+ u16 FirmwareVersion;
+ u16 FirmwareVersionRev;
+ u16 FirmwareSubVersion;
+ u16 FirmwareSignature;
+ u8 PGMaxGroup;
+ /* current WIFI_PHY values */
+ u32 ReceiveConfig;
+ enum wireless_mode CurrentWirelessMode;
+ enum ht_channel_width CurrentChannelBW;
+ u8 CurrentChannel;
+ u8 nCur40MhzPrimeSC;/* Control channel sub-carrier */
+
+ u16 BasicRateSet;
+
+ /* rf_ctrl */
+ u8 rf_chip;
+ u8 rf_type;
+ u8 NumTotalRFPath;
+
+ u8 BoardType;
+
+ /* EEPROM setting. */
+ u16 EEPROMVID;
+ u16 EEPROMPID;
+ u16 EEPROMSVID;
+ u16 EEPROMSDID;
+ u8 EEPROMCustomerID;
+ u8 EEPROMSubCustomerID;
+ u8 EEPROMVersion;
+ u8 EEPROMRegulatory;
+
+ u8 bTXPowerDataReadFromEEPORM;
+ u8 EEPROMThermalMeter;
+ u8 bAPKThermalMeterIgnore;
+
+ bool EepromOrEfuse;
+ /* 92C:256bytes, 88E:512bytes, we use union set (512bytes) */
+ u8 EfuseMap[2][HWSET_MAX_SIZE_512];
+ u8 EfuseUsedPercentage;
+ struct efuse_hal EfuseHal;
+
+ u8 Index24G_CCK_Base[MAX_RF_PATH][CHANNEL_MAX_NUMBER];
+ u8 Index24G_BW40_Base[MAX_RF_PATH][CHANNEL_MAX_NUMBER];
+ /* If only one tx, only BW20 and OFDM are used. */
+ s8 CCK_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+ s8 OFDM_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+ s8 BW20_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+ s8 BW40_24G_Diff[MAX_RF_PATH][MAX_TX_COUNT];
+
+ u8 TxPwrLevelCck[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+ /* For HT 40MHZ pwr */
+ u8 TxPwrLevelHT40_1S[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+ /* For HT 40MHZ pwr */
+ u8 TxPwrLevelHT40_2S[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+ /* HT 20<->40 Pwr diff */
+ u8 TxPwrHt20Diff[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+ /* For HT<->legacy pwr diff */
+ u8 TxPwrLegacyHtDiff[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+ /* For power group */
+ u8 PwrGroupHT20[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+ u8 PwrGroupHT40[RF_PATH_MAX][CHANNEL_MAX_NUMBER];
+
+ u8 LegacyHTTxPowerDiff;/* Legacy to HT rate power diff */
+ /* The current Tx Power Level */
+ u8 CurrentCckTxPwrIdx;
+ u8 CurrentOfdm24GTxPwrIdx;
+ u8 CurrentBW2024GTxPwrIdx;
+ u8 CurrentBW4024GTxPwrIdx;
+
+
+ /* Read/write are allow for following hardware information variables */
+ u8 framesync;
+ u32 framesyncC34;
+ u8 framesyncMonitor;
+ u8 DefaultInitialGain[4];
+ u8 pwrGroupCnt;
+ u32 MCSTxPowerLevelOriginalOffset[MAX_PG_GROUP][16];
+ u32 CCKTxPowerLevelOriginalOffset;
+
+ u8 CrystalCap;
+ u32 AntennaTxPath; /* Antenna path Tx */
+ u32 AntennaRxPath; /* Antenna path Rx */
+ u8 BluetoothCoexist;
+ u8 ExternalPA;
+
+ u8 bLedOpenDrain; /* Open-drain support for controlling the LED.*/
+
+ u8 b1x1RecvCombine; /* for 1T1R receive combining */
+
+ u32 AcParam_BE; /* Original parameter for BE, use for EDCA turbo. */
+
+ struct bb_reg_def PHYRegDef[4]; /* Radio A/B/C/D */
+
+ u32 RfRegChnlVal[2];
+
+ /* RDG enable */
+ bool bRDGEnable;
+
+ /* for host message to fw */
+ u8 LastHMEBoxNum;
+
+ u8 fw_ractrl;
+ u8 RegTxPause;
+ /* Beacon function related global variable. */
+ u32 RegBcnCtrlVal;
+ u8 RegFwHwTxQCtrl;
+ u8 RegReg542;
+ u8 RegCR_1;
+
+ struct dm_priv dmpriv;
+ struct odm_dm_struct odmpriv;
+ struct sreset_priv srestpriv;
+
+ u8 CurAntenna;
+ u8 AntDivCfg;
+ u8 TRxAntDivType;
+
+
+ u8 bDumpRxPkt;/* for debug */
+ u8 bDumpTxPkt;/* for debug */
+ u8 FwRsvdPageStartOffset; /* Reserve page start offset except
+ * beacon in TxQ. */
+
+ /* 2010/08/09 MH Add CU power down mode. */
+ bool pwrdown;
+
+ /* Add for dual MAC 0--Mac0 1--Mac1 */
+ u32 interfaceIndex;
+
+ u8 OutEpQueueSel;
+ u8 OutEpNumber;
+
+ /* Add for USB aggreation mode dynamic shceme. */
+ bool UsbRxHighSpeedMode;
+
+ /* 2010/11/22 MH Add for slim combo debug mode selective. */
+ /* This is used for fix the drawback of CU TSMC-A/UMC-A cut.
+ * HW auto suspend ability. Close BT clock. */
+ bool SlimComboDbg;
+
+ u16 EfuseUsedBytes;
+
+#ifdef CONFIG_88EU_P2P
+ struct P2P_PS_Offload_t p2p_ps_offload;
+#endif
+
+ /* Auto FSM to Turn On, include clock, isolation, power control
+ * for MAC only */
+ u8 bMacPwrCtrlOn;
+
+ u32 UsbBulkOutSize;
+
+ /* Interrupt relatd register information. */
+ u32 IntArray[3];/* HISR0,HISR1,HSISR */
+ u32 IntrMask[3];
+ u8 C2hArray[16];
+ u8 UsbTxAggMode;
+ u8 UsbTxAggDescNum;
+ u16 HwRxPageSize; /* Hardware setting */
+ u32 MaxUsbRxAggBlock;
+
+ enum usb_rx_agg_mode UsbRxAggMode;
+ u8 UsbRxAggBlockCount; /* USB Block count. Block size is
+ * 512-byte in high speed and 64-byte
+ * in full speed */
+ u8 UsbRxAggBlockTimeout;
+ u8 UsbRxAggPageCount; /* 8192C DMA page count */
+ u8 UsbRxAggPageTimeout;
+};
+
+#define GET_HAL_DATA(__pAdapter) \
+ ((struct hal_data_8188e *)((__pAdapter)->HalData))
+#define GET_RF_TYPE(priv) (GET_HAL_DATA(priv)->rf_type)
+
+#define INCLUDE_MULTI_FUNC_BT(_Adapter) \
+ (GET_HAL_DATA(_Adapter)->MultiFunc & RT_MULTI_FUNC_BT)
+#define INCLUDE_MULTI_FUNC_GPS(_Adapter) \
+ (GET_HAL_DATA(_Adapter)->MultiFunc & RT_MULTI_FUNC_GPS)
+
+/* rtl8188e_hal_init.c */
+s32 rtl8188e_FirmwareDownload(struct adapter *padapter);
+void _8051Reset88E(struct adapter *padapter);
+void rtl8188e_InitializeFirmwareVars(struct adapter *padapter);
+
+
+s32 InitLLTTable(struct adapter *padapter, u8 txpktbuf_bndy);
+
+/* EFuse */
+u8 GetEEPROMSize8188E(struct adapter *padapter);
+void Hal_InitPGData88E(struct adapter *padapter);
+void Hal_EfuseParseIDCode88E(struct adapter *padapter, u8 *hwinfo);
+void Hal_ReadTxPowerInfo88E(struct adapter *padapter, u8 *hwinfo,
+ bool AutoLoadFail);
+
+void Hal_EfuseParseEEPROMVer88E(struct adapter *padapter, u8 *hwinfo,
+ bool AutoLoadFail);
+void rtl8188e_EfuseParseChnlPlan(struct adapter *padapter, u8 *hwinfo,
+ bool AutoLoadFail);
+void Hal_EfuseParseCustomerID88E(struct adapter *padapter, u8 *hwinfo,
+ bool AutoLoadFail);
+void Hal_ReadAntennaDiversity88E(struct adapter *pAdapter,u8 *PROMContent,
+ bool AutoLoadFail);
+void Hal_ReadThermalMeter_88E(struct adapter * dapter, u8 *PROMContent,
+ bool AutoloadFail);
+void Hal_EfuseParseXtal_8188E(struct adapter *pAdapter, u8 *hwinfo,
+ bool AutoLoadFail);
+void Hal_EfuseParseBoardType88E(struct adapter *pAdapter, u8 *hwinfo,
+ bool AutoLoadFail);
+void Hal_ReadPowerSavingMode88E(struct adapter *pAdapter, u8 *hwinfo,
+ bool AutoLoadFail);
+
+bool HalDetectPwrDownMode88E(struct adapter *Adapter);
+
+void Hal_InitChannelPlan(struct adapter *padapter);
+void rtl8188e_set_hal_ops(struct hal_ops *pHalFunc);
+
+/* register */
+void SetBcnCtrlReg(struct adapter *padapter, u8 SetBits, u8 ClearBits);
+
+void rtl8188e_clone_haldata(struct adapter *dst, struct adapter *src);
+void rtl8188e_start_thread(struct adapter *padapter);
+void rtl8188e_stop_thread(struct adapter *padapter);
+
+void rtw_IOL_cmd_tx_pkt_buf_dump(struct adapter *Adapter, int len);
+s32 rtl8188e_iol_efuse_patch(struct adapter *padapter);
+void rtw_cancel_all_timer(struct adapter *padapter);
+void _ps_open_RF(struct adapter *adapt);
+
+#endif /* __RTL8188E_HAL_H__ */
--- /dev/null
+/******************************************************************************
+ *
+ * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
+ *
+ *******************************************************************************/
+#ifndef __RTL8188E_SPEC_H__
+#define __RTL8188E_SPEC_H__
+
+#ifndef BIT
+#define BIT(x) (1 << (x))
+#endif
+
+#define BIT0 0x00000001
+#define BIT1 0x00000002
+#define BIT2 0x00000004
+#define BIT3 0x00000008
+#define BIT4 0x00000010
+#define BIT5 0x00000020
+#define BIT6 0x00000040
+#define BIT7 0x00000080
+#define BIT8 0x00000100
+#define BIT9 0x00000200
+#define BIT10 0x00000400
+#define BIT11 0x00000800
+#define BIT12 0x00001000
+#define BIT13 0x00002000
+#define BIT14 0x00004000
+#define BIT15 0x00008000
+#define BIT16 0x00010000
+#define BIT17 0x00020000
+#define BIT18 0x00040000
+#define BIT19 0x00080000
+#define BIT20 0x00100000
+#define BIT21 0x00200000
+#define BIT22 0x00400000
+#define BIT23 0x00800000
+#define BIT24 0x01000000
+#define BIT25 0x02000000
+#define BIT26 0x04000000
+#define BIT27 0x08000000
+#define BIT28 0x10000000
+#define BIT29 0x20000000
+#define BIT30 0x40000000
+#define BIT31 0x80000000
+
+/* 8192C Regsiter offset definition */
+
+#define HAL_PS_TIMER_INT_DELAY 50 /* 50 microseconds */
+#define HAL_92C_NAV_UPPER_UNIT 128 /* micro-second */
+
+#define MAC_ADDR_LEN 6
+/* 8188E PKT_BUFF_ACCESS_CTRL value */
+#define TXPKT_BUF_SELECT 0x69
+#define RXPKT_BUF_SELECT 0xA5
+#define DISABLE_TRXPKT_BUF_ACCESS 0x0
+
+
+/* 0x0000h ~ 0x00FFh System Configuration */
+#define REG_SYS_ISO_CTRL 0x0000
+#define REG_SYS_FUNC_EN 0x0002
+#define REG_APS_FSMCO 0x0004
+#define REG_SYS_CLKR 0x0008
+#define REG_9346CR 0x000A
+#define REG_EE_VPD 0x000C
+#define REG_AFE_MISC 0x0010
+#define REG_SPS0_CTRL 0x0011
+#define REG_SPS_OCP_CFG 0x0018
+#define REG_RSV_CTRL 0x001C
+#define REG_RF_CTRL 0x001F
+#define REG_LDOA15_CTRL 0x0020
+#define REG_LDOV12D_CTRL 0x0021
+#define REG_LDOHCI12_CTRL 0x0022
+#define REG_LPLDO_CTRL 0x0023
+#define REG_AFE_XTAL_CTRL 0x0024
+#define REG_AFE_PLL_CTRL 0x0028
+#define REG_APE_PLL_CTRL_EXT 0x002c
+#define REG_EFUSE_CTRL 0x0030
+#define REG_EFUSE_TEST 0x0034
+#define REG_GPIO_MUXCFG 0x0040
+#define REG_GPIO_IO_SEL 0x0042
+#define REG_MAC_PINMUX_CFG 0x0043
+#define REG_GPIO_PIN_CTRL 0x0044
+#define REG_GPIO_INTM 0x0048
+#define REG_LEDCFG0 0x004C
+#define REG_LEDCFG1 0x004D
+#define REG_LEDCFG2 0x004E
+#define REG_LEDCFG3 0x004F
+#define REG_FSIMR 0x0050
+#define REG_FSISR 0x0054
+#define REG_HSIMR 0x0058
+#define REG_HSISR 0x005c
+#define REG_GPIO_PIN_CTRL_2 0x0060 /* RTL8723 WIFI/BT/GPS
+ * Multi-Function GPIO Pin Control. */
+#define REG_GPIO_IO_SEL_2 0x0062 /* RTL8723 WIFI/BT/GPS
+ * Multi-Function GPIO Select. */
+#define REG_BB_PAD_CTRL 0x0064
+#define REG_MULTI_FUNC_CTRL 0x0068 /* RTL8723 WIFI/BT/GPS
+ * Multi-Function control source. */
+#define REG_GPIO_OUTPUT 0x006c
+#define REG_AFE_XTAL_CTRL_EXT 0x0078 /* RTL8188E */
+#define REG_XCK_OUT_CTRL 0x007c /* RTL8188E */
+#define REG_MCUFWDL 0x0080
+#define REG_WOL_EVENT 0x0081 /* RTL8188E */
+#define REG_MCUTSTCFG 0x0084
+#define REG_HMEBOX_E0 0x0088
+#define REG_HMEBOX_E1 0x008A
+#define REG_HMEBOX_E2 0x008C
+#define REG_HMEBOX_E3 0x008E
+#define REG_HMEBOX_EXT_0 0x01F0
+#define REG_HMEBOX_EXT_1 0x01F4
+#define REG_HMEBOX_EXT_2 0x01F8
+#define REG_HMEBOX_EXT_3 0x01FC
+#define REG_HIMR_88E 0x00B0
+#define REG_HISR_88E 0x00B4
+#define REG_HIMRE_88E 0x00B8
+#define REG_HISRE_88E 0x00BC
+#define REG_EFUSE_ACCESS 0x00CF /* Efuse access protection
+ * for RTL8723 */
+#define REG_BIST_SCAN 0x00D0
+#define REG_BIST_RPT 0x00D4
+#define REG_BIST_ROM_RPT 0x00D8
+#define REG_USB_SIE_INTF 0x00E0
+#define REG_PCIE_MIO_INTF 0x00E4
+#define REG_PCIE_MIO_INTD 0x00E8
+#define REG_HPON_FSM 0x00EC
+#define REG_SYS_CFG 0x00F0
+#define REG_GPIO_OUTSTS 0x00F4 /* For RTL8723 only. */
+#define REG_TYPE_ID 0x00FC
+
+#define REG_MAC_PHY_CTRL_NORMAL 0x00f8
+
+/* 0x0100h ~ 0x01FFh MACTOP General Configuration */
+#define REG_CR 0x0100
+#define REG_PBP 0x0104
+#define REG_PKT_BUFF_ACCESS_CTRL 0x0106
+#define REG_TRXDMA_CTRL 0x010C
+#define REG_TRXFF_BNDY 0x0114
+#define REG_TRXFF_STATUS 0x0118
+#define REG_RXFF_PTR 0x011C
+/* define REG_HIMR 0x0120 */
+/* define REG_HISR 0x0124 */
+#define REG_HIMRE 0x0128
+#define REG_HISRE 0x012C
+#define REG_CPWM 0x012F
+#define REG_FWIMR 0x0130
+#define REG_FTIMR 0x0138
+#define REG_FWISR 0x0134
+#define REG_PKTBUF_DBG_CTRL 0x0140
+#define REG_PKTBUF_DBG_ADDR (REG_PKTBUF_DBG_CTRL)
+#define REG_RXPKTBUF_DBG (REG_PKTBUF_DBG_CTRL+2)
+#define REG_TXPKTBUF_DBG (REG_PKTBUF_DBG_CTRL+3)
+#define REG_RXPKTBUF_CTRL (REG_PKTBUF_DBG_CTRL+2)
+#define REG_PKTBUF_DBG_DATA_L 0x0144
+#define REG_PKTBUF_DBG_DATA_H 0x0148
+
+#define REG_TC0_CTRL 0x0150
+#define REG_TC1_CTRL 0x0154
+#define REG_TC2_CTRL 0x0158
+#define REG_TC3_CTRL 0x015C
+#define REG_TC4_CTRL 0x0160
+#define REG_TCUNIT_BASE 0x0164
+#define REG_MBIST_START 0x0174
+#define REG_MBIST_DONE 0x0178
+#define REG_MBIST_FAIL 0x017C
+#define REG_32K_CTRL 0x0194 /* RTL8188E */
+#define REG_C2HEVT_MSG_NORMAL 0x01A0
+#define REG_C2HEVT_CLEAR 0x01AF
+#define REG_MCUTST_1 0x01c0
+#define REG_FMETHR 0x01C8
+#define REG_HMETFR 0x01CC
+#define REG_HMEBOX_0 0x01D0
+#define REG_HMEBOX_1 0x01D4
+#define REG_HMEBOX_2 0x01D8
+#define REG_HMEBOX_3 0x01DC
+
+#define REG_LLT_INIT 0x01E0
+
+/* 0x0200h ~ 0x027Fh TXDMA Configuration */
+#define REG_RQPN 0x0200
+#define REG_FIFOPAGE 0x0204
+#define REG_TDECTRL 0x0208
+#define REG_TXDMA_OFFSET_CHK 0x020C
+#define REG_TXDMA_STATUS 0x0210
+#define REG_RQPN_NPQ 0x0214
+
+/* 0x0280h ~ 0x02FFh RXDMA Configuration */
+#define REG_RXDMA_AGG_PG_TH 0x0280
+#define REG_RXPKT_NUM 0x0284
+#define REG_RXDMA_STATUS 0x0288
+
+/* 0x0300h ~ 0x03FFh PCIe */
+#define REG_PCIE_CTRL_REG 0x0300
+#define REG_INT_MIG 0x0304 /* Interrupt Migration */
+#define REG_BCNQ_DESA 0x0308 /* TX Beacon Descr Address */
+#define REG_HQ_DESA 0x0310 /* TX High Queue Descr Addr */
+#define REG_MGQ_DESA 0x0318 /* TX Manage Queue Descr Addr*/
+#define REG_VOQ_DESA 0x0320 /* TX VO Queue Descr Addr */
+#define REG_VIQ_DESA 0x0328 /* TX VI Queue Descr Addr */
+#define REG_BEQ_DESA 0x0330 /* TX BE Queue Descr Addr */
+#define REG_BKQ_DESA 0x0338 /* TX BK Queue Descr Addr */
+#define REG_RX_DESA 0x0340 /* RX Queue Descr Addr */
+#define REG_MDIO 0x0354 /* MDIO for Access PCIE PHY */
+#define REG_DBG_SEL 0x0360 /* Debug Selection Register */
+#define REG_PCIE_HRPWM 0x0361 /* PCIe RPWM */
+#define REG_PCIE_HCPWM 0x0363 /* PCIe CPWM */
+#define REG_WATCH_DOG 0x0368
+
+/* RTL8723 series ------------------------------ */
+#define REG_PCIE_HISR 0x03A0
+
+/* spec version 11 */
+/* 0x0400h ~ 0x047Fh Protocol Configuration */
+#define REG_VOQ_INFORMATION 0x0400
+#define REG_VIQ_INFORMATION 0x0404
+#define REG_BEQ_INFORMATION 0x0408
+#define REG_BKQ_INFORMATION 0x040C
+#define REG_MGQ_INFORMATION 0x0410
+#define REG_HGQ_INFORMATION 0x0414
+#define REG_BCNQ_INFORMATION 0x0418
+#define REG_TXPKT_EMPTY 0x041A
+
+#define REG_CPU_MGQ_INFORMATION 0x041C
+#define REG_FWHW_TXQ_CTRL 0x0420
+#define REG_HWSEQ_CTRL 0x0423
+#define REG_TXPKTBUF_BCNQ_BDNY 0x0424
+#define REG_TXPKTBUF_MGQ_BDNY 0x0425
+#define REG_LIFETIME_EN 0x0426
+#define REG_MULTI_BCNQ_OFFSET 0x0427
+#define REG_SPEC_SIFS 0x0428
+#define REG_RL 0x042A
+#define REG_DARFRC 0x0430
+#define REG_RARFRC 0x0438
+#define REG_RRSR 0x0440
+#define REG_ARFR0 0x0444
+#define REG_ARFR1 0x0448
+#define REG_ARFR2 0x044C
+#define REG_ARFR3 0x0450
+#define REG_AGGLEN_LMT 0x0458
+#define REG_AMPDU_MIN_SPACE 0x045C
+#define REG_TXPKTBUF_WMAC_LBK_BF_HD 0x045D
+#define REG_FAST_EDCA_CTRL 0x0460
+#define REG_RD_RESP_PKT_TH 0x0463
+#define REG_INIRTS_RATE_SEL 0x0480
+/* define REG_INIDATA_RATE_SEL 0x0484 */
+#define REG_POWER_STATUS 0x04A4
+#define REG_POWER_STAGE1 0x04B4
+#define REG_POWER_STAGE2 0x04B8
+#define REG_PKT_VO_VI_LIFE_TIME 0x04C0
+#define REG_PKT_BE_BK_LIFE_TIME 0x04C2
+#define REG_STBC_SETTING 0x04C4
+#define REG_PROT_MODE_CTRL 0x04C8
+#define REG_MAX_AGGR_NUM 0x04CA
+#define REG_RTS_MAX_AGGR_NUM 0x04CB
+#define REG_BAR_MODE_CTRL 0x04CC
+#define REG_RA_TRY_RATE_AGG_LMT 0x04CF
+#define REG_EARLY_MODE_CONTROL 0x4D0
+#define REG_NQOS_SEQ 0x04DC
+#define REG_QOS_SEQ 0x04DE
+#define REG_NEED_CPU_HANDLE 0x04E0
+#define REG_PKT_LOSE_RPT 0x04E1
+#define REG_PTCL_ERR_STATUS 0x04E2
+#define REG_TX_RPT_CTRL 0x04EC
+#define REG_TX_RPT_TIME 0x04F0 /* 2 byte */
+#define REG_DUMMY 0x04FC
+
+/* 0x0500h ~ 0x05FFh EDCA Configuration */
+#define REG_EDCA_VO_PARAM 0x0500
+#define REG_EDCA_VI_PARAM 0x0504
+#define REG_EDCA_BE_PARAM 0x0508
+#define REG_EDCA_BK_PARAM 0x050C
+#define REG_BCNTCFG 0x0510
+#define REG_PIFS 0x0512
+#define REG_RDG_PIFS 0x0513
+#define REG_SIFS_CTX 0x0514
+#define REG_SIFS_TRX 0x0516
+#define REG_TSFTR_SYN_OFFSET 0x0518
+#define REG_AGGR_BREAK_TIME 0x051A
+#define REG_SLOT 0x051B
+#define REG_TX_PTCL_CTRL 0x0520
+#define REG_TXPAUSE 0x0522
+#define REG_DIS_TXREQ_CLR 0x0523
+#define REG_RD_CTRL 0x0524
+/* Format for offset 540h-542h: */
+/* [3:0]: TBTT prohibit setup in unit of 32us. The time for HW getting
+ * beacon content before TBTT. */
+/* [7:4]: Reserved. */
+/* [19:8]: TBTT prohibit hold in unit of 32us. The time for HW holding
+ * to send the beacon packet. */
+/* [23:20]: Reserved */
+/* Description: */
+/* | */
+/* |<--Setup--|--Hold------------>| */
+/* --------------|---------------------- */
+/* | */
+/* TBTT */
+/* Note: We cannot update beacon content to HW or send any AC packets during
+ * the time between Setup and Hold. */
+#define REG_TBTT_PROHIBIT 0x0540
+#define REG_RD_NAV_NXT 0x0544
+#define REG_NAV_PROT_LEN 0x0546
+#define REG_BCN_CTRL 0x0550
+#define REG_BCN_CTRL_1 0x0551
+#define REG_MBID_NUM 0x0552
+#define REG_DUAL_TSF_RST 0x0553
+#define REG_BCN_INTERVAL 0x0554
+#define REG_DRVERLYINT 0x0558
+#define REG_BCNDMATIM 0x0559
+#define REG_ATIMWND 0x055A
+#define REG_BCN_MAX_ERR 0x055D
+#define REG_RXTSF_OFFSET_CCK 0x055E
+#define REG_RXTSF_OFFSET_OFDM 0x055F
+#define REG_TSFTR 0x0560
+#define REG_TSFTR1 0x0568
+#define REG_ATIMWND_1 0x0570
+#define REG_PSTIMER 0x0580
+#define REG_TIMER0 0x0584
+#define REG_TIMER1 0x0588
+#define REG_ACMHWCTRL 0x05C0
+
+/* define REG_FW_TSF_SYNC_CNT 0x04A0 */
+#define REG_FW_RESET_TSF_CNT_1 0x05FC
+#define REG_FW_RESET_TSF_CNT_0 0x05FD
+#define REG_FW_BCN_DIS_CNT 0x05FE
+
+/* 0x0600h ~ 0x07FFh WMAC Configuration */
+#define REG_APSD_CTRL 0x0600
+#define REG_BWOPMODE 0x0603
+#define REG_TCR 0x0604
+#define REG_RCR 0x0608
+#define REG_RX_PKT_LIMIT 0x060C
+#define REG_RX_DLK_TIME 0x060D
+#define REG_RX_DRVINFO_SZ 0x060F
+
+#define REG_MACID 0x0610
+#define REG_BSSID 0x0618
+#define REG_MAR 0x0620
+#define REG_MBIDCAMCFG 0x0628
+
+#define REG_USTIME_EDCA 0x0638
+#define REG_MAC_SPEC_SIFS 0x063A
+
+/* 20100719 Joseph: Hardware register definition change. (HW datasheet v54) */
+/* [15:8]SIFS_R2T_OFDM, [7:0]SIFS_R2T_CCK */
+#define REG_R2T_SIFS 0x063C
+/* [15:8]SIFS_T2T_OFDM, [7:0]SIFS_T2T_CCK */
+#define REG_T2T_SIFS 0x063E
+#define REG_ACKTO 0x0640
+#define REG_CTS2TO 0x0641
+#define REG_EIFS 0x0642
+
+/* RXERR_RPT */
+#define RXERR_TYPE_OFDM_PPDU 0
+#define RXERR_TYPE_OFDM_false_ALARM 1
+#define RXERR_TYPE_OFDM_MPDU_OK 2
+#define RXERR_TYPE_OFDM_MPDU_FAIL 3
+#define RXERR_TYPE_CCK_PPDU 4
+#define RXERR_TYPE_CCK_false_ALARM 5
+#define RXERR_TYPE_CCK_MPDU_OK 6
+#define RXERR_TYPE_CCK_MPDU_FAIL 7
+#define RXERR_TYPE_HT_PPDU 8
+#define RXERR_TYPE_HT_false_ALARM 9
+#define RXERR_TYPE_HT_MPDU_TOTAL 10
+#define RXERR_TYPE_HT_MPDU_OK 11
+#define RXERR_TYPE_HT_MPDU_FAIL 12
+#define RXERR_TYPE_RX_FULL_DROP 15
+
+#define RXERR_COUNTER_MASK 0xFFFFF
+#define RXERR_RPT_RST BIT(27)
+#define _RXERR_RPT_SEL(type) ((type) << 28)
+
+/* Note: */
+/* The NAV upper value is very important to WiFi 11n 5.2.3 NAV test.
+ * The default value is always too small, but the WiFi TestPlan test
+ * by 25,000 microseconds of NAV through sending CTS in the air.
+ * We must update this value greater than 25,000 microseconds to pass
+ * the item. The offset of NAV_UPPER in 8192C Spec is incorrect, and
+ * the offset should be 0x0652. */
+#define REG_NAV_UPPER 0x0652 /* unit of 128 */
+
+/* WMA, BA, CCX */
+/* define REG_NAV_CTRL 0x0650 */
+#define REG_BACAMCMD 0x0654
+#define REG_BACAMCONTENT 0x0658
+#define REG_LBDLY 0x0660
+#define REG_FWDLY 0x0661
+#define REG_RXERR_RPT 0x0664
+#define REG_WMAC_TRXPTCL_CTL 0x0668
+
+/* Security */
+#define REG_CAMCMD 0x0670
+#define REG_CAMWRITE 0x0674
+#define REG_CAMREAD 0x0678
+#define REG_CAMDBG 0x067C
+#define REG_SECCFG 0x0680
+
+/* Power */
+#define REG_WOW_CTRL 0x0690
+#define REG_PS_RX_INFO 0x0692
+#define REG_UAPSD_TID 0x0693
+#define REG_WKFMCAM_CMD 0x0698
+#define REG_WKFMCAM_NUM_88E 0x698
+#define REG_RXFLTMAP0 0x06A0
+#define REG_RXFLTMAP1 0x06A2
+#define REG_RXFLTMAP2 0x06A4
+#define REG_BCN_PSR_RPT 0x06A8
+#define REG_BT_COEX_TABLE 0x06C0
+
+/* Hardware Port 2 */
+#define REG_MACID1 0x0700
+#define REG_BSSID1 0x0708
+
+/* 0xFE00h ~ 0xFE55h USB Configuration */
+#define REG_USB_INFO 0xFE17
+#define REG_USB_SPECIAL_OPTION 0xFE55
+#define REG_USB_DMA_AGG_TO 0xFE5B
+#define REG_USB_AGG_TO 0xFE5C
+#define REG_USB_AGG_TH 0xFE5D
+
+/* For normal chip */
+#define REG_NORMAL_SIE_VID 0xFE60 /* 0xFE60~0xFE61 */
+#define REG_NORMAL_SIE_PID 0xFE62 /* 0xFE62~0xFE63 */
+#define REG_NORMAL_SIE_OPTIONAL 0xFE64
+#define REG_NORMAL_SIE_EP 0xFE65 /* 0xFE65~0xFE67 */
+#define REG_NORMAL_SIE_PHY 0xFE68 /* 0xFE68~0xFE6B */
+#define REG_NORMAL_SIE_OPTIONAL2 0xFE6C
+#define REG_NORMAL_SIE_GPS_EP 0xFE6D /* 0xFE6D, for RTL8723 only. */
+#define REG_NORMAL_SIE_MAC_ADDR 0xFE70 /* 0xFE70~0xFE75 */
+#define REG_NORMAL_SIE_STRING 0xFE80 /* 0xFE80~0xFEDF */
+
+/* TODO: use these definition when using REG_xxx naming rule. */
+/* NOTE: DO NOT Remove these definition. Use later. */
+
+#define EFUSE_CTRL REG_EFUSE_CTRL /* E-Fuse Control. */
+#define EFUSE_TEST REG_EFUSE_TEST /* E-Fuse Test. */
+#define MSR (REG_CR + 2) /* Media Status reg */
+#define ISR REG_HISR_88E
+/* Timing Sync Function Timer Register. */
+#define TSFR REG_TSFTR
+
+#define PBP REG_PBP
+
+/* Redifine MACID register, to compatible prior ICs. */
+/* MAC ID Register, Offset 0x0050-0x0053 */
+#define IDR0 REG_MACID
+/* MAC ID Register, Offset 0x0054-0x0055 */
+#define IDR4 (REG_MACID + 4)
+
+/* 9. Security Control Registers (Offset: ) */
+/* IN 8190 Data Sheet is called CAMcmd */
+#define RWCAM REG_CAMCMD
+/* Software write CAM input content */
+#define WCAMI REG_CAMWRITE
+/* Software read/write CAM config */
+#define RCAMO REG_CAMREAD
+#define CAMDBG REG_CAMDBG
+/* Security Configuration Register */
+#define SECR REG_SECCFG
+
+/* Unused register */
+#define UnusedRegister 0x1BF
+#define DCAM UnusedRegister
+#define PSR UnusedRegister
+#define BBAddr UnusedRegister
+#define PhyDataR UnusedRegister
+
+/* Min Spacing related settings. */
+#define MAX_MSS_DENSITY_2T 0x13
+#define MAX_MSS_DENSITY_1T 0x0A
+
+/* EEPROM enable when set 1 */
+#define CmdEEPROM_En BIT5
+/* System EEPROM select, 0: boot from E-FUSE, 1: The EEPROM used is 9346 */
+#define CmdEERPOMSEL BIT4
+#define Cmd9346CR_9356SEL BIT4
+
+/* 8192C GPIO MUX Configuration Register (offset 0x40, 4 byte) */
+#define GPIOSEL_GPIO 0
+#define GPIOSEL_ENBT BIT5
+
+/* 8192C GPIO PIN Control Register (offset 0x44, 4 byte) */
+/* GPIO pins input value */
+#define GPIO_IN REG_GPIO_PIN_CTRL
+/* GPIO pins output value */
+#define GPIO_OUT (REG_GPIO_PIN_CTRL+1)
+/* GPIO pins output enable when a bit is set to "1"; otherwise,
+ * input is configured. */
+#define GPIO_IO_SEL (REG_GPIO_PIN_CTRL+2)
+#define GPIO_MOD (REG_GPIO_PIN_CTRL+3)
+
+/* 8723/8188E Host System Interrupt Mask Register (offset 0x58, 32 byte) */
+#define HSIMR_GPIO12_0_INT_EN BIT0
+#define HSIMR_SPS_OCP_INT_EN BIT5
+#define HSIMR_RON_INT_EN BIT6
+#define HSIMR_PDN_INT_EN BIT7
+#define HSIMR_GPIO9_INT_EN BIT25
+
+/* 8723/8188E Host System Interrupt Status Register (offset 0x5C, 32 byte) */
+#define HSISR_GPIO12_0_INT BIT0
+#define HSISR_SPS_OCP_INT BIT5
+#define HSISR_RON_INT_EN BIT6
+#define HSISR_PDNINT BIT7
+#define HSISR_GPIO9_INT BIT25
+
+/* 8192C (MSR) Media Status Register (Offset 0x4C, 8 bits) */
+/*
+Network Type
+00: No link
+01: Link in ad hoc network
+10: Link in infrastructure network
+11: AP mode
+Default: 00b.
+*/
+#define MSR_NOLINK 0x00
+#define MSR_ADHOC 0x01
+#define MSR_INFRA 0x02
+#define MSR_AP 0x03
+
+/* 88EU (MSR) Media Status Register (Offset 0x4C, 8 bits) */
+#define USB_INTR_CONTENT_C2H_OFFSET 0
+#define USB_INTR_CONTENT_CPWM1_OFFSET 16
+#define USB_INTR_CONTENT_CPWM2_OFFSET 20
+#define USB_INTR_CONTENT_HISR_OFFSET 48
+#define USB_INTR_CONTENT_HISRE_OFFSET 52
+
+/* 88E Driver Initialization Offload REG_FDHM0(Offset 0x88, 8 bits) */
+/* IOL config for REG_FDHM0(Reg0x88) */
+#define CMD_INIT_LLT BIT0
+#define CMD_READ_EFUSE_MAP BIT1
+#define CMD_EFUSE_PATCH BIT2
+#define CMD_IOCONFIG BIT3
+#define CMD_INIT_LLT_ERR BIT4
+#define CMD_READ_EFUSE_MAP_ERR BIT5
+#define CMD_EFUSE_PATCH_ERR BIT6
+#define CMD_IOCONFIG_ERR BIT7
+
+/* 6. Adaptive Control Registers (Offset: 0x0160 - 0x01CF) */
+/* 8192C Response Rate Set Register (offset 0x181, 24bits) */
+#define RRSR_1M BIT0
+#define RRSR_2M BIT1
+#define RRSR_5_5M BIT2
+#define RRSR_11M BIT3
+#define RRSR_6M BIT4
+#define RRSR_9M BIT5
+#define RRSR_12M BIT6
+#define RRSR_18M BIT7
+#define RRSR_24M BIT8
+#define RRSR_36M BIT9
+#define RRSR_48M BIT10
+#define RRSR_54M BIT11
+#define RRSR_MCS0 BIT12
+#define RRSR_MCS1 BIT13
+#define RRSR_MCS2 BIT14
+#define RRSR_MCS3 BIT15
+#define RRSR_MCS4 BIT16
+#define RRSR_MCS5 BIT17
+#define RRSR_MCS6 BIT18
+#define RRSR_MCS7 BIT19
+
+/* 8192C Response Rate Set Register (offset 0x1BF, 8bits) */
+/* WOL bit information */
+#define HAL92C_WOL_PTK_UPDATE_EVENT BIT0
+#define HAL92C_WOL_GTK_UPDATE_EVENT BIT1
+
+/* 8192C BW_OPMODE bits (Offset 0x203, 8bit) */
+#define BW_OPMODE_20MHZ BIT2
+#define BW_OPMODE_5G BIT1
+
+/* 8192C CAM Config Setting (offset 0x250, 1 byte) */
+#define CAM_VALID BIT15
+#define CAM_NOTVALID 0x0000
+#define CAM_USEDK BIT5
+
+#define CAM_CONTENT_COUNT 8
+
+#define CAM_NONE 0x0
+#define CAM_WEP40 0x01
+#define CAM_TKIP 0x02
+#define CAM_AES 0x04
+#define CAM_WEP104 0x05
+#define CAM_SMS4 0x6
+
+#define TOTAL_CAM_ENTRY 32
+#define HALF_CAM_ENTRY 16
+
+#define CAM_CONFIG_USEDK true
+#define CAM_CONFIG_NO_USEDK false
+
+#define CAM_WRITE BIT16
+#define CAM_READ 0x00000000
+#define CAM_POLLINIG BIT31
+
+#define SCR_UseDK 0x01
+#define SCR_TxSecEnable 0x02
+#define SCR_RxSecEnable 0x04
+
+/* 10. Power Save Control Registers (Offset: 0x0260 - 0x02DF) */
+#define WOW_PMEN BIT0 /* Power management Enable. */
+#define WOW_WOMEN BIT1 /* WoW function on or off. */
+#define WOW_MAGIC BIT2 /* Magic packet */
+#define WOW_UWF BIT3 /* Unicast Wakeup frame. */
+
+/* 12. Host Interrupt Status Registers (Offset: 0x0300 - 0x030F) */
+/* 8188 IMR/ISR bits */
+#define IMR_DISABLED_88E 0x0
+/* IMR DW0(0x0060-0063) Bit 0-31 */
+#define IMR_TXCCK_88E BIT30 /* TXRPT interrupt when CCX bit of the packet is set */
+#define IMR_PSTIMEOUT_88E BIT29 /* Power Save Time Out Interrupt */
+#define IMR_GTINT4_88E BIT28 /* When GTIMER4 expires, this bit is set to 1 */
+#define IMR_GTINT3_88E BIT27 /* When GTIMER3 expires, this bit is set to 1 */
+#define IMR_TBDER_88E BIT26 /* Transmit Beacon0 Error */
+#define IMR_TBDOK_88E BIT25 /* Transmit Beacon0 OK */
+#define IMR_TSF_BIT32_TOGGLE_88E BIT24 /* TSF Timer BIT32 toggle indication interrupt */
+#define IMR_BCNDMAINT0_88E BIT20 /* Beacon DMA Interrupt 0 */
+#define IMR_BCNDERR0_88E BIT16 /* Beacon Queue DMA Error 0 */
+#define IMR_HSISR_IND_ON_INT_88E BIT15 /* HSISR Indicator (HSIMR & HSISR is true, this bit is set to 1) */
+#define IMR_BCNDMAINT_E_88E BIT14 /* Beacon DMA Interrupt Extension for Win7 */
+#define IMR_ATIMEND_88E BIT12 /* CTWidnow End or ATIM Window End */
+#define IMR_HISR1_IND_INT_88E BIT11 /* HISR1 Indicator (HISR1 & HIMR1 is true, this bit is set to 1) */
+#define IMR_C2HCMD_88E BIT10 /* CPU to Host Command INT Status, Write 1 clear */
+#define IMR_CPWM2_88E BIT9 /* CPU power Mode exchange INT Status, Write 1 clear */
+#define IMR_CPWM_88E BIT8 /* CPU power Mode exchange INT Status, Write 1 clear */
+#define IMR_HIGHDOK_88E BIT7 /* High Queue DMA OK */
+#define IMR_MGNTDOK_88E BIT6 /* Management Queue DMA OK */
+#define IMR_BKDOK_88E BIT5 /* AC_BK DMA OK */
+#define IMR_BEDOK_88E BIT4 /* AC_BE DMA OK */
+#define IMR_VIDOK_88E BIT3 /* AC_VI DMA OK */
+#define IMR_VODOK_88E BIT2 /* AC_VO DMA OK */
+#define IMR_RDU_88E BIT1 /* Rx Descriptor Unavailable */
+#define IMR_ROK_88E BIT0 /* Receive DMA OK */
+
+/* IMR DW1(0x00B4-00B7) Bit 0-31 */
+#define IMR_BCNDMAINT7_88E BIT27 /* Beacon DMA Interrupt 7 */
+#define IMR_BCNDMAINT6_88E BIT26 /* Beacon DMA Interrupt 6 */
+#define IMR_BCNDMAINT5_88E BIT25 /* Beacon DMA Interrupt 5 */
+#define IMR_BCNDMAINT4_88E BIT24 /* Beacon DMA Interrupt 4 */
+#define IMR_BCNDMAINT3_88E BIT23 /* Beacon DMA Interrupt 3 */
+#define IMR_BCNDMAINT2_88E BIT22 /* Beacon DMA Interrupt 2 */
+#define IMR_BCNDMAINT1_88E BIT21 /* Beacon DMA Interrupt 1 */
+#define IMR_BCNDERR7_88E BIT20 /* Beacon DMA Error Int 7 */
+#define IMR_BCNDERR6_88E BIT19 /* Beacon DMA Error Int 6 */
+#define IMR_BCNDERR5_88E BIT18 /* Beacon DMA Error Int 5 */
+#define IMR_BCNDERR4_88E BIT17 /* Beacon DMA Error Int 4 */
+#define IMR_BCNDERR3_88E BIT16 /* Beacon DMA Error Int 3 */
+#define IMR_BCNDERR2_88E BIT15 /* Beacon DMA Error Int 2 */
+#define IMR_BCNDERR1_88E BIT14 /* Beacon DMA Error Int 1 */
+#define IMR_ATIMEND_E_88E BIT13 /* ATIM Window End Ext for Win7 */
+#define IMR_TXERR_88E BIT11 /* Tx Err Flag Int Status, write 1 clear. */
+#define IMR_RXERR_88E BIT10 /* Rx Err Flag INT Status, Write 1 clear */
+#define IMR_TXFOVW_88E BIT9 /* Transmit FIFO Overflow */
+#define IMR_RXFOVW_88E BIT8 /* Receive FIFO Overflow */
+
+#define HAL_NIC_UNPLUG_ISR 0xFFFFFFFF /* The value when the NIC is unplugged for PCI. */
+
+/* 8192C EFUSE */
+#define HWSET_MAX_SIZE 256
+#define HWSET_MAX_SIZE_88E 512
+
+/*===================================================================
+=====================================================================
+Here the register defines are for 92C. When the define is as same with 92C,
+we will use the 92C's define for the consistency
+So the following defines for 92C is not entire!!!!!!
+=====================================================================
+=====================================================================*/
+/*
+Based on Datasheet V33---090401
+Register Summary
+Current IOREG MAP
+0x0000h ~ 0x00FFh System Configuration (256 Bytes)
+0x0100h ~ 0x01FFh MACTOP General Configuration (256 Bytes)
+0x0200h ~ 0x027Fh TXDMA Configuration (128 Bytes)
+0x0280h ~ 0x02FFh RXDMA Configuration (128 Bytes)
+0x0300h ~ 0x03FFh PCIE EMAC Reserved Region (256 Bytes)
+0x0400h ~ 0x04FFh Protocol Configuration (256 Bytes)
+0x0500h ~ 0x05FFh EDCA Configuration (256 Bytes)
+0x0600h ~ 0x07FFh WMAC Configuration (512 Bytes)
+0x2000h ~ 0x3FFFh 8051 FW Download Region (8196 Bytes)
+*/
+/* 8192C (TXPAUSE) transmission pause (Offset 0x522, 8 bits) */
+/* Note: */
+/* The bits of stopping AC(VO/VI/BE/BK) queue in datasheet
+ * RTL8192S/RTL8192C are wrong, */
+/* the correct arragement is VO - Bit0, VI - Bit1, BE - Bit2,
+ * and BK - Bit3. */
+/* 8723 and 88E may be not correct either in the earlier version. */
+#define StopBecon BIT6
+#define StopHigh BIT5
+#define StopMgt BIT4
+#define StopBK BIT3
+#define StopBE BIT2
+#define StopVI BIT1
+#define StopVO BIT0
+
+/* 8192C (RCR) Receive Configuration Register(Offset 0x608, 32 bits) */
+#define RCR_APPFCS BIT31 /* WMAC append FCS after payload */
+#define RCR_APP_MIC BIT30
+#define RCR_APP_PHYSTS BIT28
+#define RCR_APP_ICV BIT29
+#define RCR_APP_PHYST_RXFF BIT28
+#define RCR_APP_BA_SSN BIT27 /* Accept BA SSN */
+#define RCR_ENMBID BIT24 /* Enable Multiple BssId. */
+#define RCR_LSIGEN BIT23
+#define RCR_MFBEN BIT22
+#define RCR_HTC_LOC_CTRL BIT14 /* MFC<--HTC=1 MFC-->HTC=0 */
+#define RCR_AMF BIT13 /* Accept management type frame */
+#define RCR_ACF BIT12 /* Accept control type frame */
+#define RCR_ADF BIT11 /* Accept data type frame */
+#define RCR_AICV BIT9 /* Accept ICV error packet */
+#define RCR_ACRC32 BIT8 /* Accept CRC32 error packet */
+#define RCR_CBSSID_BCN BIT7 /* Accept BSSID match packet
+ * (Rx beacon, probe rsp) */
+#define RCR_CBSSID_DATA BIT6 /* Accept BSSID match (Data)*/
+#define RCR_CBSSID RCR_CBSSID_DATA /* Accept BSSID match */
+#define RCR_APWRMGT BIT5 /* Accept power management pkt*/
+#define RCR_ADD3 BIT4 /* Accept address 3 match pkt */
+#define RCR_AB BIT3 /* Accept broadcast packet */
+#define RCR_AM BIT2 /* Accept multicast packet */
+#define RCR_APM BIT1 /* Accept physical match pkt */
+#define RCR_AAP BIT0 /* Accept all unicast packet */
+#define RCR_MXDMA_OFFSET 8
+#define RCR_FIFO_OFFSET 13
+
+/* 0xFE00h ~ 0xFE55h USB Configuration */
+#define REG_USB_INFO 0xFE17
+#define REG_USB_SPECIAL_OPTION 0xFE55
+#define REG_USB_DMA_AGG_TO 0xFE5B
+#define REG_USB_AGG_TO 0xFE5C
+#define REG_USB_AGG_TH 0xFE5D
+
+#define REG_USB_HRPWM 0xFE58
+#define REG_USB_HCPWM 0xFE57
+/* 8192C Regsiter Bit and Content definition */
+/* 0x0000h ~ 0x00FFh System Configuration */
+
+/* 2 SYS_ISO_CTRL */
+#define ISO_MD2PP BIT(0)
+#define ISO_UA2USB BIT(1)
+#define ISO_UD2CORE BIT(2)
+#define ISO_PA2PCIE BIT(3)
+#define ISO_PD2CORE BIT(4)
+#define ISO_IP2MAC BIT(5)
+#define ISO_DIOP BIT(6)
+#define ISO_DIOE BIT(7)
+#define ISO_EB2CORE BIT(8)
+#define ISO_DIOR BIT(9)
+#define PWC_EV12V BIT(15)
+
+/* 2 SYS_FUNC_EN */
+#define FEN_BBRSTB BIT(0)
+#define FEN_BB_GLB_RSTn BIT(1)
+#define FEN_USBA BIT(2)
+#define FEN_UPLL BIT(3)
+#define FEN_USBD BIT(4)
+#define FEN_DIO_PCIE BIT(5)
+#define FEN_PCIEA BIT(6)
+#define FEN_PPLL BIT(7)
+#define FEN_PCIED BIT(8)
+#define FEN_DIOE BIT(9)
+#define FEN_CPUEN BIT(10)
+#define FEN_DCORE BIT(11)
+#define FEN_ELDR BIT(12)
+#define FEN_DIO_RF BIT(13)
+#define FEN_HWPDN BIT(14)
+#define FEN_MREGEN BIT(15)
+
+/* 2 APS_FSMCO */
+#define PFM_LDALL BIT(0)
+#define PFM_ALDN BIT(1)
+#define PFM_LDKP BIT(2)
+#define PFM_WOWL BIT(3)
+#define EnPDN BIT(4)
+#define PDN_PL BIT(5)
+#define APFM_ONMAC BIT(8)
+#define APFM_OFF BIT(9)
+#define APFM_RSM BIT(10)
+#define AFSM_HSUS BIT(11)
+#define AFSM_PCIE BIT(12)
+#define APDM_MAC BIT(13)
+#define APDM_HOST BIT(14)
+#define APDM_HPDN BIT(15)
+#define RDY_MACON BIT(16)
+#define SUS_HOST BIT(17)
+#define ROP_ALD BIT(20)
+#define ROP_PWR BIT(21)
+#define ROP_SPS BIT(22)
+#define SOP_MRST BIT(25)
+#define SOP_FUSE BIT(26)
+#define SOP_ABG BIT(27)
+#define SOP_AMB BIT(28)
+#define SOP_RCK BIT(29)
+#define SOP_A8M BIT(30)
+#define XOP_BTCK BIT(31)
+
+/* 2 SYS_CLKR */
+#define ANAD16V_EN BIT(0)
+#define ANA8M BIT(1)
+#define MACSLP BIT(4)
+#define LOADER_CLK_EN BIT(5)
+
+/* 2 9346CR */
+
+#define BOOT_FROM_EEPROM BIT(4)
+#define EEPROM_EN BIT(5)
+
+/* 2 SPS0_CTRL */
+
+/* 2 SPS_OCP_CFG */
+
+/* 2 RF_CTRL */
+#define RF_EN BIT(0)
+#define RF_RSTB BIT(1)
+#define RF_SDMRSTB BIT(2)
+
+/* 2 LDOV12D_CTRL */
+#define LDV12_EN BIT(0)
+#define LDV12_SDBY BIT(1)
+#define LPLDO_HSM BIT(2)
+#define LPLDO_LSM_DIS BIT(3)
+#define _LDV12_VADJ(x) (((x) & 0xF) << 4)
+
+/* 2EFUSE_CTRL */
+#define ALD_EN BIT(18)
+#define EF_PD BIT(19)
+#define EF_FLAG BIT(31)
+
+/* 2 EFUSE_TEST (For RTL8723 partially) */
+#define EF_TRPT BIT(7)
+/* 00: Wifi Efuse, 01: BT Efuse0, 10: BT Efuse1, 11: BT Efuse2 */
+#define EF_CELL_SEL (BIT(8)|BIT(9))
+#define LDOE25_EN BIT(31)
+#define EFUSE_SEL(x) (((x) & 0x3) << 8)
+#define EFUSE_SEL_MASK 0x300
+#define EFUSE_WIFI_SEL_0 0x0
+#define EFUSE_BT_SEL_0 0x1
+#define EFUSE_BT_SEL_1 0x2
+#define EFUSE_BT_SEL_2 0x3
+
+#define EFUSE_ACCESS_ON 0x69 /* For RTL8723 only. */
+#define EFUSE_ACCESS_OFF 0x00 /* For RTL8723 only. */
+
+/* 2 8051FWDL */
+/* 2 MCUFWDL */
+#define MCUFWDL_EN BIT(0)
+#define MCUFWDL_RDY BIT(1)
+#define FWDL_ChkSum_rpt BIT(2)
+#define MACINI_RDY BIT(3)
+#define BBINI_RDY BIT(4)
+#define RFINI_RDY BIT(5)
+#define WINTINI_RDY BIT(6)
+#define RAM_DL_SEL BIT(7) /* 1:RAM, 0:ROM */
+#define ROM_DLEN BIT(19)
+#define CPRST BIT(23)
+
+/* 2 REG_SYS_CFG */
+#define XCLK_VLD BIT(0)
+#define ACLK_VLD BIT(1)
+#define UCLK_VLD BIT(2)
+#define PCLK_VLD BIT(3)
+#define PCIRSTB BIT(4)
+#define V15_VLD BIT(5)
+#define SW_OFFLOAD_EN BIT(7)
+#define SIC_IDLE BIT(8)
+#define BD_MAC2 BIT(9)
+#define BD_MAC1 BIT(10)
+#define IC_MACPHY_MODE BIT(11)
+#define CHIP_VER (BIT(12)|BIT(13)|BIT(14)|BIT(15))
+#define BT_FUNC BIT(16)
+#define VENDOR_ID BIT(19)
+#define PAD_HWPD_IDN BIT(22)
+#define TRP_VAUX_EN BIT(23) /* RTL ID */
+#define TRP_BT_EN BIT(24)
+#define BD_PKG_SEL BIT(25)
+#define BD_HCI_SEL BIT(26)
+#define TYPE_ID BIT(27)
+
+#define CHIP_VER_RTL_MASK 0xF000 /* Bit 12 ~ 15 */
+#define CHIP_VER_RTL_SHIFT 12
+
+/* 2REG_GPIO_OUTSTS (For RTL8723 only) */
+#define EFS_HCI_SEL (BIT(0)|BIT(1))
+#define PAD_HCI_SEL (BIT(2)|BIT(3))
+#define HCI_SEL (BIT(4)|BIT(5))
+#define PKG_SEL_HCI BIT(6)
+#define FEN_GPS BIT(7)
+#define FEN_BT BIT(8)
+#define FEN_WL BIT(9)
+#define FEN_PCI BIT(10)
+#define FEN_USB BIT(11)
+#define BTRF_HWPDN_N BIT(12)
+#define WLRF_HWPDN_N BIT(13)
+#define PDN_BT_N BIT(14)
+#define PDN_GPS_N BIT(15)
+#define BT_CTL_HWPDN BIT(16)
+#define GPS_CTL_HWPDN BIT(17)
+#define PPHY_SUSB BIT(20)
+#define UPHY_SUSB BIT(21)
+#define PCI_SUSEN BIT(22)
+#define USB_SUSEN BIT(23)
+#define RF_RL_ID (BIT(31)|BIT(30)|BIT(29)|BIT(28))
+
+/* 2SYS_CFG */
+#define RTL_ID BIT(23) /* TestChip ID, 1:Test(RLE); 0:MP(RL) */
+
+/* 0x0100h ~ 0x01FFh MACTOP General Configuration */
+
+/* 2 Function Enable Registers */
+/* 2 CR */
+
+#define HCI_TXDMA_EN BIT(0)
+#define HCI_RXDMA_EN BIT(1)
+#define TXDMA_EN BIT(2)
+#define RXDMA_EN BIT(3)
+#define PROTOCOL_EN BIT(4)
+#define SCHEDULE_EN BIT(5)
+#define MACTXEN BIT(6)
+#define MACRXEN BIT(7)
+#define ENSWBCN BIT(8)
+#define ENSEC BIT(9)
+#define CALTMR_EN BIT(10) /* 32k CAL TMR enable */
+
+/* Network type */
+#define _NETTYPE(x) (((x) & 0x3) << 16)
+#define MASK_NETTYPE 0x30000
+#define NT_NO_LINK 0x0
+#define NT_LINK_AD_HOC 0x1
+#define NT_LINK_AP 0x2
+#define NT_AS_AP 0x3
+
+/* 2 PBP - Page Size Register */
+#define GET_RX_PAGE_SIZE(value) ((value) & 0xF)
+#define GET_TX_PAGE_SIZE(value) (((value) & 0xF0) >> 4)
+#define _PSRX_MASK 0xF
+#define _PSTX_MASK 0xF0
+#define _PSRX(x) (x)
+#define _PSTX(x) ((x) << 4)
+
+#define PBP_64 0x0
+#define PBP_128 0x1
+#define PBP_256 0x2
+#define PBP_512 0x3
+#define PBP_1024 0x4
+
+/* 2 TX/RXDMA */
+#define RXDMA_ARBBW_EN BIT(0)
+#define RXSHFT_EN BIT(1)
+#define RXDMA_AGG_EN BIT(2)
+#define QS_VO_QUEUE BIT(8)
+#define QS_VI_QUEUE BIT(9)
+#define QS_BE_QUEUE BIT(10)
+#define QS_BK_QUEUE BIT(11)
+#define QS_MANAGER_QUEUE BIT(12)
+#define QS_HIGH_QUEUE BIT(13)
+
+#define HQSEL_VOQ BIT(0)
+#define HQSEL_VIQ BIT(1)
+#define HQSEL_BEQ BIT(2)
+#define HQSEL_BKQ BIT(3)
+#define HQSEL_MGTQ BIT(4)
+#define HQSEL_HIQ BIT(5)
+
+/* For normal driver, 0x10C */
+#define _TXDMA_HIQ_MAP(x) (((x)&0x3) << 14)
+#define _TXDMA_MGQ_MAP(x) (((x)&0x3) << 12)
+#define _TXDMA_BKQ_MAP(x) (((x)&0x3) << 10)
+#define _TXDMA_BEQ_MAP(x) (((x)&0x3) << 8 )
+#define _TXDMA_VIQ_MAP(x) (((x)&0x3) << 6 )
+#define _TXDMA_VOQ_MAP(x) (((x)&0x3) << 4 )
+
+#define QUEUE_LOW 1
+#define QUEUE_NORMAL 2
+#define QUEUE_HIGH 3
+
+/* 2 TRXFF_BNDY */
+
+/* 2 LLT_INIT */
+#define _LLT_NO_ACTIVE 0x0
+#define _LLT_WRITE_ACCESS 0x1
+#define _LLT_READ_ACCESS 0x2
+
+#define _LLT_INIT_DATA(x) ((x) & 0xFF)
+#define _LLT_INIT_ADDR(x) (((x) & 0xFF) << 8)
+#define _LLT_OP(x) (((x) & 0x3) << 30)
+#define _LLT_OP_VALUE(x) (((x) >> 30) & 0x3)
+
+/* 0x0200h ~ 0x027Fh TXDMA Configuration */
+/* 2RQPN */
+#define _HPQ(x) ((x) & 0xFF)
+#define _LPQ(x) (((x) & 0xFF) << 8)
+#define _PUBQ(x) (((x) & 0xFF) << 16)
+/* NOTE: in RQPN_NPQ register */
+#define _NPQ(x) ((x) & 0xFF)
+
+#define HPQ_PUBLIC_DIS BIT(24)
+#define LPQ_PUBLIC_DIS BIT(25)
+#define LD_RQPN BIT(31)
+
+/* 2TDECTRL */
+#define BCN_VALID BIT(16)
+#define BCN_HEAD(x) (((x) & 0xFF) << 8)
+#define BCN_HEAD_MASK 0xFF00
+
+/* 2 TDECTL */
+#define BLK_DESC_NUM_SHIFT 4
+#define BLK_DESC_NUM_MASK 0xF
+
+/* 2 TXDMA_OFFSET_CHK */
+#define DROP_DATA_EN BIT(9)
+
+/* 0x0280h ~ 0x028Bh RX DMA Configuration */
+
+/* REG_RXDMA_CONTROL, 0x0286h */
+
+/* 2 REG_RXPKT_NUM, 0x0284 */
+#define RXPKT_RELEASE_POLL BIT(16)
+#define RXDMA_IDLE BIT(17)
+#define RW_RELEASE_EN BIT(18)
+
+/* 0x0400h ~ 0x047Fh Protocol Configuration */
+/* 2 FWHW_TXQ_CTRL */
+#define EN_AMPDU_RTY_NEW BIT(7)
+
+/* 2 SPEC SIFS */
+#define _SPEC_SIFS_CCK(x) ((x) & 0xFF)
+#define _SPEC_SIFS_OFDM(x) (((x) & 0xFF) << 8)
+
+/* 2 RL */
+#define RETRY_LIMIT_SHORT_SHIFT 8
+#define RETRY_LIMIT_LONG_SHIFT 0
+
+/* 0x0500h ~ 0x05FFh EDCA Configuration */
+
+/* 2 EDCA setting */
+#define AC_PARAM_TXOP_LIMIT_OFFSET 16
+#define AC_PARAM_ECW_MAX_OFFSET 12
+#define AC_PARAM_ECW_MIN_OFFSET 8
+#define AC_PARAM_AIFS_OFFSET 0
+
+#define _LRL(x) ((x) & 0x3F)
+#define _SRL(x) (((x) & 0x3F) << 8)
+
+/* 2 BCN_CTRL */
+#define EN_MBSSID BIT(1)
+#define EN_TXBCN_RPT BIT(2)
+#define EN_BCN_FUNCTION BIT(3)
+#define DIS_TSF_UPDATE BIT(3)
+
+/* The same function but different bit field. */
+#define DIS_TSF_UDT0_NORMAL_CHIP BIT(4)
+#define DIS_TSF_UDT0_TEST_CHIP BIT(5)
+#define STOP_BCNQ BIT(6)
+
+/* 2 ACMHWCTRL */
+#define AcmHw_HwEn BIT(0)
+#define AcmHw_BeqEn BIT(1)
+#define AcmHw_ViqEn BIT(2)
+#define AcmHw_VoqEn BIT(3)
+#define AcmHw_BeqStatus BIT(4)
+#define AcmHw_ViqStatus BIT(5)
+#define AcmHw_VoqStatus BIT(6)
+
+/* 0x0600h ~ 0x07FFh WMAC Configuration */
+/* 2APSD_CTRL */
+#define APSDOFF BIT(6)
+#define APSDOFF_STATUS BIT(7)
+
+#define RATE_BITMAP_ALL 0xFFFFF
+
+/* Only use CCK 1M rate for ACK */
+#define RATE_RRSR_CCK_ONLY_1M 0xFFFF1
+
+/* 2 TCR */
+#define TSFRST BIT(0)
+#define DIS_GCLK BIT(1)
+#define PAD_SEL BIT(2)
+#define PWR_ST BIT(6)
+#define PWRBIT_OW_EN BIT(7)
+#define ACRC BIT(8)
+#define CFENDFORM BIT(9)
+#define ICV BIT(10)
+
+/* 2 RCR */
+#define AAP BIT(0)
+#define APM BIT(1)
+#define AM BIT(2)
+#define AB BIT(3)
+#define ADD3 BIT(4)
+#define APWRMGT BIT(5)
+#define CBSSID BIT(6)
+#define CBSSID_DATA BIT(6)
+#define CBSSID_BCN BIT(7)
+#define ACRC32 BIT(8)
+#define AICV BIT(9)
+#define ADF BIT(11)
+#define ACF BIT(12)
+#define AMF BIT(13)
+#define HTC_LOC_CTRL BIT(14)
+#define UC_DATA_EN BIT(16)
+#define BM_DATA_EN BIT(17)
+#define MFBEN BIT(22)
+#define LSIGEN BIT(23)
+#define EnMBID BIT(24)
+#define APP_BASSN BIT(27)
+#define APP_PHYSTS BIT(28)
+#define APP_ICV BIT(29)
+#define APP_MIC BIT(30)
+#define APP_FCS BIT(31)
+
+/* 2 SECCFG */
+#define SCR_TxUseDK BIT(0) /* Force Tx Use Default Key */
+#define SCR_RxUseDK BIT(1) /* Force Rx Use Default Key */
+#define SCR_TxEncEnable BIT(2) /* Enable Tx Encryption */
+#define SCR_RxDecEnable BIT(3) /* Enable Rx Decryption */
+#define SCR_SKByA2 BIT(4) /* Search kEY BY A2 */
+#define SCR_NoSKMC BIT(5) /* No Key Search Multicast */
+#define SCR_TXBCUSEDK BIT(6) /* Force Tx Bcast pkt Use Default Key */
+#define SCR_RXBCUSEDK BIT(7) /* Force Rx Bcast pkt Use Default Key */
+
+/* RTL8188E SDIO Configuration */
+
+/* I/O bus domain address mapping */
+#define SDIO_LOCAL_BASE 0x10250000
+#define WLAN_IOREG_BASE 0x10260000
+#define FIRMWARE_FIFO_BASE 0x10270000
+#define TX_HIQ_BASE 0x10310000
+#define TX_MIQ_BASE 0x10320000
+#define TX_LOQ_BASE 0x10330000
+#define RX_RX0FF_BASE 0x10340000
+
+/* SDIO host local register space mapping. */
+#define SDIO_LOCAL_MSK 0x0FFF
+#define WLAN_IOREG_MSK 0x7FFF
+#define WLAN_FIFO_MSK 0x1FFF /* Aggregation Length[12:0] */
+#define WLAN_RX0FF_MSK 0x0003
+
+/* Without ref to the SDIO Device ID */
+#define SDIO_WITHOUT_REF_DEVICE_ID 0
+#define SDIO_LOCAL_DEVICE_ID 0 /* 0b[16], 000b[15:13] */
+#define WLAN_TX_HIQ_DEVICE_ID 4 /* 0b[16], 100b[15:13] */
+#define WLAN_TX_MIQ_DEVICE_ID 5 /* 0b[16], 101b[15:13] */
+#define WLAN_TX_LOQ_DEVICE_ID 6 /* 0b[16], 110b[15:13] */
+#define WLAN_RX0FF_DEVICE_ID 7 /* 0b[16], 111b[15:13] */
+#define WLAN_IOREG_DEVICE_ID 8 /* 1b[16] */
+
+/* SDIO Tx Free Page Index */
+#define HI_QUEUE_IDX 0
+#define MID_QUEUE_IDX 1
+#define LOW_QUEUE_IDX 2
+#define PUBLIC_QUEUE_IDX 3
+
+#define SDIO_MAX_TX_QUEUE 3 /* HIQ, MIQ and LOQ */
+#define SDIO_MAX_RX_QUEUE 1
+
+/* SDIO Tx Control */
+#define SDIO_REG_TX_CTRL 0x0000
+/* SDIO Host Interrupt Mask */
+#define SDIO_REG_HIMR 0x0014
+/* SDIO Host Interrupt Service Routine */
+#define SDIO_REG_HISR 0x0018
+/* HCI Current Power Mode */
+#define SDIO_REG_HCPWM 0x0019
+/* RXDMA Request Length */
+#define SDIO_REG_RX0_REQ_LEN 0x001C
+/* Free Tx Buffer Page */
+#define SDIO_REG_FREE_TXPG 0x0020
+/* HCI Current Power Mode 1 */
+#define SDIO_REG_HCPWM1 0x0024
+/* HCI Current Power Mode 2 */
+#define SDIO_REG_HCPWM2 0x0026
+/* HTSF Informaion */
+#define SDIO_REG_HTSFR_INFO 0x0030
+/* HCI Request Power Mode 1 */
+#define SDIO_REG_HRPWM1 0x0080
+/* HCI Request Power Mode 2 */
+#define SDIO_REG_HRPWM2 0x0082
+/* HCI Power Save Clock */
+#define SDIO_REG_HPS_CLKR 0x0084
+/* SDIO HCI Suspend Control */
+#define SDIO_REG_HSUS_CTRL 0x0086
+/* SDIO Host Extension Interrupt Mask Always */
+#define SDIO_REG_HIMR_ON 0x0090
+/* SDIO Host Extension Interrupt Status Always */
+#define SDIO_REG_HISR_ON 0x0091
+
+#define SDIO_HIMR_DISABLED 0
+
+/* RTL8188E SDIO Host Interrupt Mask Register */
+#define SDIO_HIMR_RX_REQUEST_MSK BIT0
+#define SDIO_HIMR_AVAL_MSK BIT1
+#define SDIO_HIMR_TXERR_MSK BIT2
+#define SDIO_HIMR_RXERR_MSK BIT3
+#define SDIO_HIMR_TXFOVW_MSK BIT4
+#define SDIO_HIMR_RXFOVW_MSK BIT5
+#define SDIO_HIMR_TXBCNOK_MSK BIT6
+#define SDIO_HIMR_TXBCNERR_MSK BIT7
+#define SDIO_HIMR_BCNERLY_INT_MSK BIT16
+#define SDIO_HIMR_C2HCMD_MSK BIT17
+#define SDIO_HIMR_CPWM1_MSK BIT18
+#define SDIO_HIMR_CPWM2_MSK BIT19
+#define SDIO_HIMR_HSISR_IND_MSK BIT20
+#define SDIO_HIMR_GTINT3_IND_MSK BIT21
+#define SDIO_HIMR_GTINT4_IND_MSK BIT22
+#define SDIO_HIMR_PSTIMEOUT_MSK BIT23
+#define SDIO_HIMR_OCPINT_MSK BIT24
+#define SDIO_HIMR_ATIMEND_MSK BIT25
+#define SDIO_HIMR_ATIMEND_E_MSK BIT26
+#define SDIO_HIMR_CTWEND_MSK BIT27
+
+/* RTL8188E SDIO Specific */
+#define SDIO_HIMR_MCU_ERR_MSK BIT28
+#define SDIO_HIMR_TSF_BIT32_TOGGLE_MSK BIT29
+
+/* SDIO Host Interrupt Service Routine */
+#define SDIO_HISR_RX_REQUEST BIT0
+#define SDIO_HISR_AVAL BIT1
+#define SDIO_HISR_TXERR BIT2
+#define SDIO_HISR_RXERR BIT3
+#define SDIO_HISR_TXFOVW BIT4
+#define SDIO_HISR_RXFOVW BIT5
+#define SDIO_HISR_TXBCNOK BIT6
+#define SDIO_HISR_TXBCNERR BIT7
+#define SDIO_HISR_BCNERLY_INT BIT16
+#define SDIO_HISR_C2HCMD BIT17
+#define SDIO_HISR_CPWM1 BIT18
+#define SDIO_HISR_CPWM2 BIT19
+#define SDIO_HISR_HSISR_IND BIT20
+#define SDIO_HISR_GTINT3_IND BIT21
+#define SDIO_HISR_GTINT4_IND BIT22
+#define SDIO_HISR_PSTIME BIT23
+#define SDIO_HISR_OCPINT BIT24
+#define SDIO_HISR_ATIMEND BIT25
+#define SDIO_HISR_ATIMEND_E BIT26
+#define SDIO_HISR_CTWEND BIT27
+
+/* RTL8188E SDIO Specific */
+#define SDIO_HISR_MCU_ERR BIT28
+#define SDIO_HISR_TSF_BIT32_TOGGLE BIT29
+
+#define MASK_SDIO_HISR_CLEAR \
+ (SDIO_HISR_TXERR | SDIO_HISR_RXERR | SDIO_HISR_TXFOVW |\
+ SDIO_HISR_RXFOVW | SDIO_HISR_TXBCNOK | SDIO_HISR_TXBCNERR |\
+ SDIO_HISR_C2HCMD | SDIO_HISR_CPWM1 | SDIO_HISR_CPWM2 |\
+ SDIO_HISR_HSISR_IND | SDIO_HISR_GTINT3_IND | SDIO_HISR_GTINT4_IND |\
+ SDIO_HISR_PSTIMEOUT | SDIO_HISR_OCPINT)
+
+/* SDIO HCI Suspend Control Register */
+#define HCI_RESUME_PWR_RDY BIT1
+#define HCI_SUS_CTRL BIT0
+
+/* SDIO Tx FIFO related */
+/* The number of Tx FIFO free page */
+#define SDIO_TX_FREE_PG_QUEUE 4
+#define SDIO_TX_FIFO_PAGE_SZ 128
+
+/* 0xFE00h ~ 0xFE55h USB Configuration */
+
+/* 2 USB Information (0xFE17) */
+#define USB_IS_HIGH_SPEED 0
+#define USB_IS_FULL_SPEED 1
+#define USB_SPEED_MASK BIT(5)
+
+#define USB_NORMAL_SIE_EP_MASK 0xF
+#define USB_NORMAL_SIE_EP_SHIFT 4
+
+/* 2 Special Option */
+#define USB_AGG_EN BIT(3)
+
+/* 0; Use interrupt endpoint to upload interrupt pkt */
+/* 1; Use bulk endpoint to upload interrupt pkt, */
+#define INT_BULK_SEL BIT(4)
+
+/* 2REG_C2HEVT_CLEAR */
+/* Set by driver and notify FW that the driver has read
+ * the C2H command message */
+#define C2H_EVT_HOST_CLOSE 0x00
+/* Set by FW indicating that FW had set the C2H command
+ * message and it's not yet read by driver. */
+#define C2H_EVT_FW_CLOSE 0xFF
+
+/* 2REG_MULTI_FUNC_CTRL(For RTL8723 Only) */
+/* Enable GPIO[9] as WiFi HW PDn source */
+#define WL_HWPDN_EN BIT0
+/* WiFi HW PDn polarity control */
+#define WL_HWPDN_SL BIT1
+/* WiFi function enable */
+#define WL_FUNC_EN BIT2
+/* Enable GPIO[9] as WiFi RF HW PDn source */
+#define WL_HWROF_EN BIT3
+/* Enable GPIO[11] as BT HW PDn source */
+#define BT_HWPDN_EN BIT16
+/* BT HW PDn polarity control */
+#define BT_HWPDN_SL BIT17
+/* BT function enable */
+#define BT_FUNC_EN BIT18
+/* Enable GPIO[11] as BT/GPS RF HW PDn source */
+#define BT_HWROF_EN BIT19
+/* Enable GPIO[10] as GPS HW PDn source */
+#define GPS_HWPDN_EN BIT20
+/* GPS HW PDn polarity control */
+#define GPS_HWPDN_SL BIT21
+/* GPS function enable */
+#define GPS_FUNC_EN BIT22
+
+/* 3 REG_LIFECTRL_CTRL */
+#define HAL92C_EN_PKT_LIFE_TIME_BK BIT3
+#define HAL92C_EN_PKT_LIFE_TIME_BE BIT2
+#define HAL92C_EN_PKT_LIFE_TIME_VI BIT1
+#define HAL92C_EN_PKT_LIFE_TIME_VO BIT0
+
+#define HAL92C_MSDU_LIFE_TIME_UNIT 128 /* in us */
+
+/* General definitions */
+#define LAST_ENTRY_OF_TX_PKT_BUFFER 176 /* 22k 22528 bytes */
+
+#define POLLING_LLT_THRESHOLD 20
+#define POLLING_READY_TIMEOUT_COUNT 1000
+/* GPIO BIT */
+#define HAL_8192C_HW_GPIO_WPS_BIT BIT2
+
+/* 8192C EEPROM/EFUSE share register definition. */
+
+/* EEPROM/Efuse PG Offset for 88EE/88EU/88ES */
+#define EEPROM_TX_PWR_INX_88E 0x10
+
+#define EEPROM_ChannelPlan_88E 0xB8
+#define EEPROM_XTAL_88E 0xB9
+#define EEPROM_THERMAL_METER_88E 0xBA
+#define EEPROM_IQK_LCK_88E 0xBB
+
+#define EEPROM_RF_BOARD_OPTION_88E 0xC1
+#define EEPROM_RF_FEATURE_OPTION_88E 0xC2
+#define EEPROM_RF_BT_SETTING_88E 0xC3
+#define EEPROM_VERSION_88E 0xC4
+#define EEPROM_CUSTOMERID_88E 0xC5
+#define EEPROM_RF_ANTENNA_OPT_88E 0xC9
+
+/* RTL88EE */
+#define EEPROM_MAC_ADDR_88EE 0xD0
+#define EEPROM_VID_88EE 0xD6
+#define EEPROM_DID_88EE 0xD8
+#define EEPROM_SVID_88EE 0xDA
+#define EEPROM_SMID_88EE 0xDC
+
+/* RTL88EU */
+#define EEPROM_MAC_ADDR_88EU 0xD7
+#define EEPROM_VID_88EU 0xD0
+#define EEPROM_PID_88EU 0xD2
+#define EEPROM_USB_OPTIONAL_FUNCTION0 0xD4
+
+/* RTL88ES */
+#define EEPROM_MAC_ADDR_88ES 0x11A
+
+/* EEPROM/Efuse Value Type */
+#define EETYPE_TX_PWR 0x0
+
+/* Default Value for EEPROM or EFUSE!!! */
+#define EEPROM_Default_TSSI 0x0
+#define EEPROM_Default_TxPowerDiff 0x0
+#define EEPROM_Default_CrystalCap 0x5
+/* Default: 2X2, RTL8192CE(QFPN68) */
+#define EEPROM_Default_BoardType 0x02
+#define EEPROM_Default_TxPower 0x1010
+#define EEPROM_Default_HT2T_TxPwr 0x10
+
+#define EEPROM_Default_LegacyHTTxPowerDiff 0x3
+#define EEPROM_Default_ThermalMeter 0x12
+
+#define EEPROM_Default_AntTxPowerDiff 0x0
+#define EEPROM_Default_TxPwDiff_CrystalCap 0x5
+#define EEPROM_Default_TxPowerLevel 0x2A
+
+#define EEPROM_Default_HT40_2SDiff 0x0
+/* HT20<->40 default Tx Power Index Difference */
+#define EEPROM_Default_HT20_Diff 2
+#define EEPROM_Default_LegacyHTTxPowerDiff 0x3
+#define EEPROM_Default_HT40_PwrMaxOffset 0
+#define EEPROM_Default_HT20_PwrMaxOffset 0
+
+#define EEPROM_Default_CrystalCap_88E 0x20
+#define EEPROM_Default_ThermalMeter_88E 0x18
+
+/* New EFUSE deafult value */
+#define EEPROM_DEFAULT_24G_INDEX 0x2D
+#define EEPROM_DEFAULT_24G_HT20_DIFF 0X02
+#define EEPROM_DEFAULT_24G_OFDM_DIFF 0X04
+
+#define EEPROM_DEFAULT_5G_INDEX 0X2A
+#define EEPROM_DEFAULT_5G_HT20_DIFF 0X00
+#define EEPROM_DEFAULT_5G_OFDM_DIFF 0X04
+
+#define EEPROM_DEFAULT_DIFF 0XFE
+#define EEPROM_DEFAULT_CHANNEL_PLAN 0x7F
+#define EEPROM_DEFAULT_BOARD_OPTION 0x00
+#define EEPROM_DEFAULT_FEATURE_OPTION 0x00
+#define EEPROM_DEFAULT_BT_OPTION 0x10
+
+/* For debug */
+#define EEPROM_Default_PID 0x1234
+#define EEPROM_Default_VID 0x5678
+#define EEPROM_Default_CustomerID 0xAB
+#define EEPROM_Default_CustomerID_8188E 0x00
+#define EEPROM_Default_SubCustomerID 0xCD
+#define EEPROM_Default_Version 0
+
+#define EEPROM_CHANNEL_PLAN_FCC 0x0
+#define EEPROM_CHANNEL_PLAN_IC 0x1
+#define EEPROM_CHANNEL_PLAN_ETSI 0x2
+#define EEPROM_CHANNEL_PLAN_SPA 0x3
+#define EEPROM_CHANNEL_PLAN_FRANCE 0x4
+#define EEPROM_CHANNEL_PLAN_MKK 0x5
+#define EEPROM_CHANNEL_PLAN_MKK1 0x6
+#define EEPROM_CHANNEL_PLAN_ISRAEL 0x7
+#define EEPROM_CHANNEL_PLAN_TELEC 0x8
+#define EEPROM_CHANNEL_PLAN_GLOBAL_DOMA 0x9
+#define EEPROM_CHANNEL_PLAN_WORLD_WIDE_13 0xA
+#define EEPROM_CHANNEL_PLAN_NCC 0xB
+#define EEPROM_USB_OPTIONAL1 0xE
+#define EEPROM_CHANNEL_PLAN_BY_HW_MASK 0x80
+
+#define EEPROM_CID_DEFAULT 0x0
+#define EEPROM_CID_TOSHIBA 0x4
+#define EEPROM_CID_CCX 0x10 /* CCX test. */
+#define EEPROM_CID_QMI 0x0D
+#define EEPROM_CID_WHQL 0xFE
+#define RTL_EEPROM_ID 0x8129
+
+#endif /* __RTL8188E_SPEC_H__ */
projects / linux-drm-fsl-dcu.git / commitdiff