/*
* powertv-usb.c
*
- * Description: ASIC-specific USB device setup and shutdown
+ * Description: ASIC-specific USB device setup and shutdown
*
* Copyright (C) 2005-2009 Scientific-Atlanta, Inc.
* Copyright (C) 2009 Cisco Systems, Inc.
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*
- * Author: Ken Eppinett
- * David Schleef <ds@schleef.org>
+ * Author: Ken Eppinett
+ * David Schleef <ds@schleef.org>
*
* NOTE: The bootloader allocates persistent memory at an address which is
* 16 MiB below the end of the highest address in KSEG0. All fixed
#define MCC2_GMII_RX2_CLOCK_SELECT (1 << 16)
#define ETHER_CLK_CONFIG (MCC2_GMII_GCLK_TO_PAD | \
- MCC2_ETHER125_0_CLOCK_SELECT | \
+ MCC2_ETHER125_0_CLOCK_SELECT | \
MCC2_RMII_0_CLOCK_SELECT | \
MCC2_GMII_TX0_CLOCK_SELECT | \
MCC2_GMII_RX0_CLOCK_SELECT | \
- MCC2_ETHER125_1_CLOCK_SELECT | \
+ MCC2_ETHER125_1_CLOCK_SELECT | \
MCC2_RMII_1_CLOCK_SELECT | \
MCC2_GMII_TX1_CLOCK_SELECT | \
MCC2_GMII_RX1_CLOCK_SELECT | \
- MCC2_ETHER125_2_CLOCK_SELECT | \
+ MCC2_ETHER125_2_CLOCK_SELECT | \
MCC2_RMII_2_CLOCK_SELECT | \
MCC2_GMII_TX2_CLOCK_SELECT | \
MCC2_GMII_RX2_CLOCK_SELECT)
#define QAM_FS_DISABLE_DIVIDE_BY_3 (1 << 5)
#define QAM_FS_ENABLE_PROGRAM (1 << 4)
-#define QAM_FS_ENABLE_OUTPUT (1 << 3)
-#define QAM_FS_SELECT_TEST_BYPASS (1 << 2)
-#define QAM_FS_DISABLE_DIGITAL_STANDBY (1 << 1)
+#define QAM_FS_ENABLE_OUTPUT (1 << 3)
+#define QAM_FS_SELECT_TEST_BYPASS (1 << 2)
+#define QAM_FS_DISABLE_DIGITAL_STANDBY (1 << 1)
#define QAM_FS_CHOOSE_FS (1 << 0)
/* Definitions for fs432x4a_ctl register */
static struct resource ehci_resources[] = {
{
.parent = &asic_resource,
- .start = 0,
- .end = 0xff,
- .flags = IORESOURCE_MEM,
+ .start = 0,
+ .end = 0xff,
+ .flags = IORESOURCE_MEM,
},
{
- .start = irq_usbehci,
- .end = irq_usbehci,
- .flags = IORESOURCE_IRQ,
+ .start = irq_usbehci,
+ .end = irq_usbehci,
+ .flags = IORESOURCE_IRQ,
},
};
static struct resource ohci_resources[] = {
{
.parent = &asic_resource,
- .start = 0,
- .end = 0xff,
- .flags = IORESOURCE_MEM,
+ .start = 0,
+ .end = 0xff,
+ .flags = IORESOURCE_MEM,
},
{
- .start = irq_usbohci,
- .end = irq_usbohci,
- .flags = IORESOURCE_IRQ,
+ .start = irq_usbohci,
+ .end = irq_usbohci,
+ .flags = IORESOURCE_IRQ,
},
};
*
* QAM frequency selection code, which affects the frequency at which USB
* runs. The frequency is calculated as:
- * 2^15 * ndiv * Fin
+ * 2^15 * ndiv * Fin
* Fout = ------------------------------------------------------------
- * (sdiv * (ipe * (1 + md/32) - (ipe - 2^15)*(1 + (md + 1)/32)))
+ * (sdiv * (ipe * (1 + md/32) - (ipe - 2^15)*(1 + (md + 1)/32)))
* where:
* Fin 54 MHz
* ndiv QAM_FS_NSDIV_54MHZ ? 8 : 16