* http://www.gnu.org/copyleft/gpl.html
*/
+#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
#include <linux/suspend.h>
#include <asm/cacheflush.h>
#include <asm/proc-fns.h>
#include "common.h"
#include "hardware.h"
+#define CCR 0x0
+#define BM_CCR_WB_COUNT (0x7 << 16)
+#define BM_CCR_RBC_BYPASS_COUNT (0x3f << 21)
+#define BM_CCR_RBC_EN (0x1 << 27)
+
+#define CLPCR 0x54
+#define BP_CLPCR_LPM 0
+#define BM_CLPCR_LPM (0x3 << 0)
+#define BM_CLPCR_BYPASS_PMIC_READY (0x1 << 2)
+#define BM_CLPCR_ARM_CLK_DIS_ON_LPM (0x1 << 5)
+#define BM_CLPCR_SBYOS (0x1 << 6)
+#define BM_CLPCR_DIS_REF_OSC (0x1 << 7)
+#define BM_CLPCR_VSTBY (0x1 << 8)
+#define BP_CLPCR_STBY_COUNT 9
+#define BM_CLPCR_STBY_COUNT (0x3 << 9)
+#define BM_CLPCR_COSC_PWRDOWN (0x1 << 11)
+#define BM_CLPCR_WB_PER_AT_LPM (0x1 << 16)
+#define BM_CLPCR_WB_CORE_AT_LPM (0x1 << 17)
+#define BM_CLPCR_BYP_MMDC_CH0_LPM_HS (0x1 << 19)
+#define BM_CLPCR_BYP_MMDC_CH1_LPM_HS (0x1 << 21)
+#define BM_CLPCR_MASK_CORE0_WFI (0x1 << 22)
+#define BM_CLPCR_MASK_CORE1_WFI (0x1 << 23)
+#define BM_CLPCR_MASK_CORE2_WFI (0x1 << 24)
+#define BM_CLPCR_MASK_CORE3_WFI (0x1 << 25)
+#define BM_CLPCR_MASK_SCU_IDLE (0x1 << 26)
+#define BM_CLPCR_MASK_L2CC_IDLE (0x1 << 27)
+
+#define CGPR 0x64
+#define BM_CGPR_CHICKEN_BIT (0x1 << 17)
+
+static void __iomem *ccm_base;
+
+void imx6q_set_chicken_bit(void)
+{
+ u32 val = readl_relaxed(ccm_base + CGPR);
+
+ val |= BM_CGPR_CHICKEN_BIT;
+ writel_relaxed(val, ccm_base + CGPR);
+}
+
+static void imx6q_enable_rbc(bool enable)
+{
+ u32 val;
+
+ /*
+ * need to mask all interrupts in GPC before
+ * operating RBC configurations
+ */
+ imx_gpc_mask_all();
+
+ /* configure RBC enable bit */
+ val = readl_relaxed(ccm_base + CCR);
+ val &= ~BM_CCR_RBC_EN;
+ val |= enable ? BM_CCR_RBC_EN : 0;
+ writel_relaxed(val, ccm_base + CCR);
+
+ /* configure RBC count */
+ val = readl_relaxed(ccm_base + CCR);
+ val &= ~BM_CCR_RBC_BYPASS_COUNT;
+ val |= enable ? BM_CCR_RBC_BYPASS_COUNT : 0;
+ writel(val, ccm_base + CCR);
+
+ /*
+ * need to delay at least 2 cycles of CKIL(32K)
+ * due to hardware design requirement, which is
+ * ~61us, here we use 65us for safe
+ */
+ udelay(65);
+
+ /* restore GPC interrupt mask settings */
+ imx_gpc_restore_all();
+}
+
+static void imx6q_enable_wb(bool enable)
+{
+ u32 val;
+
+ /* configure well bias enable bit */
+ val = readl_relaxed(ccm_base + CLPCR);
+ val &= ~BM_CLPCR_WB_PER_AT_LPM;
+ val |= enable ? BM_CLPCR_WB_PER_AT_LPM : 0;
+ writel_relaxed(val, ccm_base + CLPCR);
+
+ /* configure well bias count */
+ val = readl_relaxed(ccm_base + CCR);
+ val &= ~BM_CCR_WB_COUNT;
+ val |= enable ? BM_CCR_WB_COUNT : 0;
+ writel_relaxed(val, ccm_base + CCR);
+}
+
+int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
+{
+ struct irq_desc *iomuxc_irq_desc;
+ u32 val = readl_relaxed(ccm_base + CLPCR);
+
+ val &= ~BM_CLPCR_LPM;
+ switch (mode) {
+ case WAIT_CLOCKED:
+ break;
+ case WAIT_UNCLOCKED:
+ val |= 0x1 << BP_CLPCR_LPM;
+ val |= BM_CLPCR_ARM_CLK_DIS_ON_LPM;
+ break;
+ case STOP_POWER_ON:
+ val |= 0x2 << BP_CLPCR_LPM;
+ break;
+ case WAIT_UNCLOCKED_POWER_OFF:
+ val |= 0x1 << BP_CLPCR_LPM;
+ val &= ~BM_CLPCR_VSTBY;
+ val &= ~BM_CLPCR_SBYOS;
+ break;
+ case STOP_POWER_OFF:
+ val |= 0x2 << BP_CLPCR_LPM;
+ val |= 0x3 << BP_CLPCR_STBY_COUNT;
+ val |= BM_CLPCR_VSTBY;
+ val |= BM_CLPCR_SBYOS;
+ if (cpu_is_imx6sl()) {
+ val |= BM_CLPCR_BYPASS_PMIC_READY;
+ val |= BM_CLPCR_BYP_MMDC_CH0_LPM_HS;
+ } else {
+ val |= BM_CLPCR_BYP_MMDC_CH1_LPM_HS;
+ }
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /*
+ * Unmask the always pending IOMUXC interrupt #32 as wakeup source to
+ * deassert dsm_request signal, so that we can ensure dsm_request
+ * is not asserted when we're going to write CLPCR register to set LPM.
+ * After setting up LPM bits, we need to mask this wakeup source.
+ */
+ iomuxc_irq_desc = irq_to_desc(32);
+ imx_gpc_irq_unmask(&iomuxc_irq_desc->irq_data);
+ writel_relaxed(val, ccm_base + CLPCR);
+ imx_gpc_irq_mask(&iomuxc_irq_desc->irq_data);
+
+ return 0;
+}
+
static int imx6q_suspend_finish(unsigned long val)
{
cpu_do_idle();
switch (state) {
case PM_SUSPEND_MEM:
imx6q_set_lpm(STOP_POWER_OFF);
+ imx6q_enable_wb(true);
+ imx6q_enable_rbc(true);
imx_gpc_pre_suspend();
imx_anatop_pre_suspend();
imx_set_cpu_jump(0, v7_cpu_resume);
/* Zzz ... */
cpu_suspend(0, imx6q_suspend_finish);
- imx_smp_prepare();
+ if (cpu_is_imx6q() || cpu_is_imx6dl())
+ imx_smp_prepare();
imx_anatop_post_resume();
imx_gpc_post_resume();
+ imx6q_enable_rbc(false);
+ imx6q_enable_wb(false);
imx6q_set_lpm(WAIT_CLOCKED);
break;
default:
.valid = suspend_valid_only_mem,
};
+void __init imx6q_pm_set_ccm_base(void __iomem *base)
+{
+ ccm_base = base;
+}
+
void __init imx6q_pm_init(void)
{
+ struct regmap *gpr;
+
+ WARN_ON(!ccm_base);
+
+ /*
+ * Force IOMUXC irq pending, so that the interrupt to GPC can be
+ * used to deassert dsm_request signal when the signal gets
+ * asserted unexpectedly.
+ */
+ gpr = syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+ if (!IS_ERR(gpr))
+ regmap_update_bits(gpr, IOMUXC_GPR1, IMX6Q_GPR1_GINT,
+ IMX6Q_GPR1_GINT);
+
+ /* Set initial power mode */
+ imx6q_set_lpm(WAIT_CLOCKED);
+
suspend_set_ops(&imx6q_pm_ops);
}
projects / linux-drm-fsl-dcu.git / blobdiff